N-Tron 105TX-POE, 105FX-POE User Manual

105TX-POE & 105FX-POE

Unmanaged Industrial Ethernet

POE Switches

User Manual &

Installation

Guide

Rev. 041008

1

Industrial Power over Ethernet Installation Guide

105TX-POE
105FX-XX-POE
105FXE-XX-YY-POE

Where: XX = ST or SC and YY = -15, -40, or -80

Rev. 041008

2

Copyright, © N-TRON Corp., 2008
820 S. University Blvd., Suite 4E
Mobile, AL USA 36609

All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-TRON
Corp. is prohibited, except as allowed under copyright laws.

Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos
or other designations mentioned herein are trademarks of their respective owners.

The information contained in this document is subject to change without notice. N-TRON Corp. makes no
warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability or fitness for a particular purpose. In no event shall N-TRON Corp. be liable for any
incidental, special, indirect or consequential damages whatsoever included but not limited to lost profits
arising out of errors or omissions in this manual or the information contained herein.

Contact Information :

N-TRON Corp.
820 South University Blvd.
Suite 4E
Mobile, AL 36609
TEL: [phone]
FAX: [phone]
Website: www.n-tron.com
Email: [e-mail]

Rev. 041008

3

GENERAL SAFETY WARNINGS
WARNING: Do not operate the equipment in the presence of flammable gasses or fumes. Operating

electrical equipment in such an environment constitutes a definite safety hazard.

WARNING: If the equipment is used in the manner not specified by N-TRON Corp., the protection provided
by the equipment may be impaired.

WARNING: Do not perform any services on the unit unless qualified to do so. Do not substitute
unauthorized parts or make unauthorized modifications to the unit.

WARNING: Do not operate the unit with the end plates removed, as this could create a shock or fire
hazard.

WARNING: Do not operate the equipment in a manner not specified by this manual.

ENVIRONMENTAL SAFETY WARNINGS

WARNING: Disconnect the power and allow to cool 5 minutes before touching.

ELECTRICAL SAFETY WARNINGS

WARNING: Disconnect the power cable before removing the end plates.

WARNING: Do not operate the unit with the end plates removed.

WARNING: Do not work on equipment or cables during periods of lightning activity.

WARNING: Do not perform any services on the unit unless qualified to do so.

WARNING: Observe proper DC Voltage polarity when installing power input cables. Reversing voltage

polarity can cause permanent damage to the unit and void the warranty.

Rev. 041008

4

HAZARDOUS LOCATION INSTALLATION REQUIREMENTS

1. This equipment is suitable for use in Class I, Div 2, Groups A, B, C, and D, or unclassified or non-

hazardous locations only.

2. WARNING: Explosion Hazard - Substitution of components may impair suitability for Class I,

Division 2.

3. WARNING: Explosion hazard, do not disconnect while the circuit is live or unless the area is known to be

non-hazardous.

4. WARNING: Explosion Hazard - Do not remove or replace the device unless power has been switched off

or the area is known to be non-hazardous.

5. Use 60/75ºC rated Copper wire, (0.22Nm) 2 inch-lbs Tightening torque for field installed connectors.

6. WARNING: Install only in accordance with Local & National Codes of Authorities Having Jurisdiction.

7. Class I, Div 2 installations require that all devices connected to this product must be UL listed for the area in

which it is installed.

8. WARNING: Damage may occur to the RJ-45 port of the powered device (PD), if the switch is not

powered down before disconnecting the Cat5 cable.

Rev. 041008

5

Functional Overview

The 105TX-POE and 105FX-POE Power over Ethernet Unmanaged Industrial Ethernet Switches are
designed to provide power over Ethernet for POE capable devices where running a power line is either not
possible or not cost effective. This feature allows an end user to power a POE camera, wireless access
point, or any other POE capable device without the need for running separate wires for power. This also
allows the ability for a centralized battery backup for all these devices.

The 105FX-POE utilizes the IEEE compliant SC or ST duplex connectors for fiber optic communication.
All 10/100Base-TX ports utilize the RJ45 shielded connectors.

Key Features

• Compact, space saving package

• Full IEEE 802.3 & 100Base-FX Compliance

• IEEE 802.3af Compliant

• 105TX-POE - Five 10/100Base-TX RJ-45 ports (4 PSE ports and 1 uplink port)

• 105FX-POE - Four 10/100Base-TX RJ-45 ports (4 PSE ports and 1 100BaseFX fiber uplink port)

• Unmanaged operation

• Extended Environmental Specifications

-40°C to 85°C Operating Temperature

-40°C to 85°C Storage Temperature

• Operating Humidity: 10% to 90% (Non Condensing)

• Support for Full/Half Duplex Operation

• LED Link/Activity Status Indication

• LED POE Status Indication

• Power Fault Status LEDs

• Auto-negotiation, Auto-sensing Speed, Duplex, and Flow Control

• Up to 1.0 Gb/s Maximum Throughput

• Industry Standard 35mm DIN Rail Mounted Enclosure

• Redundant power inputs (46-49 VDC)

• Supports up to 15.4Watts per channel (13 Watts at the Powered Device (PD ))

• Full wire speed communications

• Hardened metal DIN Rail Enclosure

Rev. 041008

6