N-Tron 1005TX User Manual

1000 Series

Gigabit Media Converter &

Industrial Gigabit Ethernet Switch

User Manual &

Installation

Guide

(Revised 2011-09-28)

Industrial Gigabit Ethernet Switch Installation Guide

1002MC-SX 1000BaseSX multimode fiber media converter

1002MC-LX-YY 1000BaseLX singlemode fiber media converter 1003GX2-SX 1000BaseSX multimode fiber switch

1003GX2-LX-YY 1000BaseLX singlemode fiber switch 1003GX2-B Custom mix and match 1003GX2 switch 1005TX 5 port gigabit Ethernet switch

Where "YY" is: 10 for 10km max. fiber segment length

40 for 40km max. fiber segment length 80 for 80km max. fiber segment length

1003GX2-B SFP (Mini-GBIC) Fiber Transceivers:

NTSFP-SX (LC Style Connector, up to 550m)

NTSFP-LX-10 (LC Style Connector, up to 10km)

NTSFP-LX-40 (LC Style Connector, up to 40km)

NTSFP-LX-80 (LC Style Connector, up to 80km)

(Revised 2011-09-28)

Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks of their respective owners.

The information contained in this document is subject to change without notice. N-TRON Corp. makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose. In no event shall N-TRON Corp. be liable for any incidental, special, indirect or consequential damages whatsoever included but not limited to lost profits arising out of errors or omissions in this manual or the information contained herein.

Contact Information :

N-TRON Corp. 820 South University Blvd. Suite 4E Mobile, AL 36609 TEL: (251) 342-2164 FAX: (251) 342-6353 Website: www.n-tron.com Email: N-TRON_Support@n-tron.com

(Revised 2011-09-28)

ELECTRICAL SAFETY WARNINGS

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or non-hazardous locations only.

This equipment must be used with a Listed UL Industrial Power Supply.

A Recognized or Listed fuse, rated maximum 3A, minimum 30VDC, must be installed on the line side of the device.

WARNING – Explosion Hazard – Substitution of components may impair suitability for Class I, Division 2.

WARNING – Explosion Hazard – Do not disconnect while circuit is live unless area is known to be non-

hazardous.

WARNING – Explosion Hazard – Do not replace the device unless power has been switched off or the area is known to be non-hazardous.

Use 110°C or higher rated copper wire, (0.22Nm) 2 lb/in tightening torque for field installed conductors.

WARNING: Do not operate the equipment in the presence of flammable gasses or fumes. Operating electrical equipment in such an environment constitutes a definite safety hazard.

WARNING: If the equipment is used in the manner not specified by N-TRON Corp., the protection provided by the equipment may be impaired.

WARNING: Do not perform any services on the unit unless qualified to do so. Do not substitute unauthorized parts or make unauthorized modifications to the unit.

WARNING: Do not operate the unit with the end plates removed, as this could create a shock or fire hazard.

WARNING: Properly ground the unit before connecting anything else to the unit. Units not properly grounded may result in a safety risk and could be hazardous and may void the warranty. See the grounding technique section of this user manual for proper ways to ground the unit.

WARNING: Do not operate the equipment in a manner not specified by this manual.

WARNING: Do not work on equipment or cables during periods of lightning activity.

WARNING: Observe proper DC Voltage polarity when installing power input cables. Reversing voltage

polarity can cause permanent damage to the unit and void the warranty. . WARNING: Install only in accordance with Local & National Codes of Authorities Having Jurisdiction.

(Revised 2011-09-28)

LASER SAFETY (1002MC and 1003GX2 Models)

CAUTION: CLASS 1 LASER PRODUCT. Do not stare into the laser!)

(Revised 2011-09-28)

ENVIRONMENTAL SAFETY WARNINGS

WARNING: Disconnect the power and allow to cool 5 minutes before touching.

1000 Series Industrial Gigabit Ethernet Switches

The 1000 Series Unmanaged Industrial Gigabit Ethernet Switches support high speed layer 2 switching between ports. This series of switches are housed in a ruggedized aluminum enclosure, and provide Category-5 compliant 10/100/1000Base-T connections for high performance network design, and hub/repeater upgrades.

All fiber products utilize the IEEE compliant LC duplex connectors for fiber optic communications in a convenient SFP modular design. All 10/100/1000Base-T ports utilize the RJ45 shielded connectors.

The 1002MC/MCE is a two port unmanaged media converter that converts 10/100/1000Base-T copper to 1000BaseSX/LX full duplex fiber.

The 1003GX2/GXE2 is a three port unmanaged switch that offers one 10/100/1000Base-T copper port and two 1000BaseT/SX/LX full duplex copper/fiber ports.

The 1005TX is a five port unmanaged switch that offers five 10/100/1000Base-T copper ports.

Key Features

 Compact Space Saving Package  Full IEEE 802.3 Compliance  Unmanaged Operation  Jumbo Frame Support  Extended Environmental Specifications

-40°C to 85°C Operating and Storage Temperature

 Supports Full/Half Duplex Operation  Up to 10.0 Gb/s Maximum Throughput  MDIX Auto Sensing Cable  Auto Sensing Speed and Flow Control  Full Wire Speed Communication  Store-and-forward Technology  Redundant Power Inputs (10-30 VDC)  LED Link/Activity Status Indication  Hardened Metal Enclosure  Industry Standard 35mm DIN Rail Mounted Enclosure

(Revised 2011-09-28)

+ 14 hidden pages