NSC LM3354MMX-5.0, LM3354MMX-3.3, LM3354MMX-1.8, LM3354MM-5.0, LM3354MM-4.1 Datasheet

...
LM3354 Regulated 90mA Buck-Boost Switched Capacitor DC/DC Converter
General Description
The LM3354 is a CMOS switched capacitor DC/DC con­verter that produces a regulated output voltage by automati­cally stepping up (boost) or stepping down (buck) the input voltage. It accepts an input voltage between 2.5V and 5.5V. The LM3354 is available with standard output voltages of
1.8V, 3.3V, 4.1V (ideal forwhite LED applications), and 5.0V. If other output voltage options between 1.8V and 5.0V are desired, please contact your National Semiconductor repre­sentative.
The LM3354’s proprietary buck-boost architecture enables up to 90mA of load current at an average efficiency greater than 75%. Typical operating current is only 375 µA and the typical shutdown current is only 2.3 µA.
The LM3354 is available in a 10-pin MSOP package. This package has a maximum height of only 1.1 mm.
The high efficiency of the LM3354, low operating and shut­down currents, small package size, and the small size of the overall solution make this device ideal for battery powered, portable, and hand-held applications.
See the LM3352 for up to 200mA of output current or the LM3355 for up to 50mA of output current.
Features
n Regulated V
OUT
with±3% (5.0V, 4.1V, and 3.3V
options) or
±
4% (1.8V option) accuracy
n Standard output voltages of 1.8V, 3.3V, 4.1V, and 5.0V n Custom output voltages available from 1.8V to 5.0V in
100 mV increments with volume order
n 2.5V to 5.5V input voltage range n Up to 90mA (5.0V, 4.1V, and 1.8V options) or 70mA
(3.3V option) output current
n
>
75% average efficiency
n Uses few, low-cost external components n Very small solution size n 375 µA typical operating current n 2.3 µA typical shutdown current n 1 MHz typical switching frequency n Architecture and control methods provide high load
current and good efficiency
n MSOP-10 package n Over-temperature protection
Applications
n White LED display backlights n 1-cell Lilon battery-operated equipment including PDAs,
hand-held PCs, cellular phones
n Flat panel displays n Hand-held instruments n Li-Ion, NiCd, NiMH, or alkaline battery powered systems
Typical Operating Circuit
DS200188-1
February 2002
LM3354 Regulated 90mA Buck-Boost Switched Capacitor DC/DC Converter
© 2002 National Semiconductor Corporation DS200188 www.national.com
Connection Diagram
Ordering Information
Order Number Package Type NSC Package Drawing Supplied As
LM3354MMX-5.0 MSOP-10 MUB10A 3.5k Units, Tape and Reel LM3354MM-5.0 MSOP-10 MUB10A 1k Units, Tape and Reel LM3354MMX-4.1 MSOP-10 MUB10A 3.5k Units, Tape and Reel LM3354MM-4.1 MSOP-10 MUB10A 1k Units, Tape and Reel LM3354MMX-3.3 MSOP-10 MUB10A 3.5k Units, Tape and Reel LM3354MM-3.3 MSOP-10 MUB10A 1k Units, Tape and Reel LM3354MMX-1.8 MSOP-10 MUB10A 3.5k Units, Tape and Reel LM3354MM-1.8 MSOP-10 MUB10A 1k Units, Tape and Reel
Pin Description
Pin Number Name Function
1V
IN
Input Supply Voltage 2 C1− Negative Terminal for C1 3 C1+ Positive Terminal for C1 4 GND Ground 5 GND Ground 6C
FIL
Filter Capacitor, a 1µF capacitor is recommended. 7SD
Shutdown, active low 8V
OUT
Regulated Output Voltage 9 C2− Negative Terminal for C2
10 C2+ Positive Terminal for C2
DS200188-2
Top View
MSOP-10 Pin Package
See NS Package Number MM
LM3354
www.national.com 2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.
All Pins −0.5V to 5.6V Power Dissipation (T
A
= 25˚C)
(Note 2) Internally Limited
T
JMAX
(Note 2) 150˚C
θ
JA
(Note 2) 250˚C/W Storage Temperature −65˚C to +150˚C Lead Temperature (Soldering, 5 sec.) 260˚C
ESD Rating (Note 3)
Human Body Model Machine Model
1.5 kV 100V
Operating Ratings
Input Voltage (VIN) 2.5V to 5.5V Output Voltage (V
OUT
) 1.8V to 5.0V
Ambient Temperature (T
A
) (Note 2) −40˚C to +85˚C
Junction Temperature (T
J
) (Note 2) −40˚C to +120˚C
Electrical Characteristics
Limits in standard typeface are for TA= 25˚C, and limits in boldface type apply over the full operating temperature range. Un­less otherwise specified: C
1=C2
= 0.33 µF; CIN= 10 µF; C
OUT
= 10 µF; C
FIL
= 1 µF; VIN= 3.5V.
Parameter Conditions Min
(Note 5)
Typ
(Note 4)
Max
(Note 5)
Units
LM3354-5.0
Output Voltage (V
OUT
) 3.4V<V
IN
<
5.5V;
1mA
<
I
LOAD
<
90 mA
4.85/4.8 5.0 5.15/5.2
V
3.1V
<
V
IN
<
5.5V;
1mA
<
I
LOAD
<
55 mA
4.85/4.8 5.0 5.15/5.2
2.9V
<
V
IN
<
5.5V;
1mA
<
I
LOAD
<
30 mA
4.85/4.8 5.0 5.15/5.2
Efficiency I
LOAD
=15mA 85
%
I
LOAD
= 40 mA, VIN= 3.8V 85
Output Voltage Ripple (Peak-to-Peak)
I
LOAD
=50mA
C
OUT
= 10 µF ceramic
75 mV
P-P
LM3354-4.1
Output Voltage (V
OUT
) 2.9V<V
IN
<
5.5V;
1mA
<
I
LOAD
<
90 mA
3.977/3.936 4.1 4.223/4.264 V
2.5V
<
V
IN
<
5.5V;
1mA
<
I
LOAD
<
40 mA
3.977/3.936 4.1 4.223/4.264
Efficiency I
LOAD
=15mA 80
%
I
LOAD
=70mA 75
Output Voltage Ripple (Peak-to-Peak)
I
LOAD
=50mA
C
OUT
= 10 µF ceramic
75 mV
P-P
LM3354-3.3
Output Voltage (V
OUT
) 2.9V<V
IN
<
5.5V;
1mA
<
I
LOAD
<
70 mA
3.201/3.168 3.3 3.399/3.432 V
2.5V
<
V
IN
<
5.5V;
1mA
<
I
LOAD
<
70 mA
3.201/3.168 3.3 3.399/3.432
Efficiency I
LOAD
=15mA 90
%
I
LOAD
=70mA 70
Output Voltage Ripple (Peak-to-Peak)
I
LOAD
=50mA
C
OUT
= 10 µF ceramic
75 mV
P-P
LM3354-1.8
Output Voltage (V
OUT
) 2.9V<V
IN
<
5.5V;
1mA
<
I
LOAD
<
90 mA
1.728/1.710 1.8 1.872/1.89 V
2.5V
<
V
IN
<
5.5V;
1mA
<
I
LOAD
<
80 mA
1.728/1.710 1.8 1.872/1.89
Efficiency I
LOAD
=15mA 75
%
I
LOAD
=70mA 70
Output Voltage Ripple (Peak-to-Peak)
I
LOAD
=50mA
C
OUT
= 10 µF ceramic
25 mV
P-P
LM3354
www.national.com3
Electrical Characteristics (Continued)
Limits in standard typeface are for TA= 25˚C, and limits in boldface type apply over the full operating temperature range. Un­less otherwise specified: C
1=C2
= 0.33 µF; CIN= 10 µF; C
OUT
= 10 µF; C
FIL
= 1 µF; VIN= 3.5V.
Parameter Conditions Min
(Note 5)
Typ
(Note 4)
Max
(Note 5)
Units
LM3354-ALL OUTPUT VOLTAGE VERSIONS
Operating Quiescent Current
Measured at Pin V
IN
;
I
LOAD
= 0A (Note 6)
375 475 µA
Shutdown Quiescent Current
SD Pin at 0V (Note 7) 2.3 5 µA
Switching Frequency 0.6 1 1.4 MHz SD Input Threshold Low 2.5V
<
V
IN
<
5.5V 0.2 V
IN
V
SD Input Threshold High 2.5V
<
V
IN
<
5.5V 0.8 V
IN
V
SD Input Current Measured at SD Pin;
SD Pin = V
IN
= 5.5V
0.3 µA
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is intended to be functional, but device parameter specifications may not be guaranteed. For guaranteed specifications and test conditions, see “Electrical Characteristics”.
Note 2: As long as T
A
+85˚C, all electrical characteristics hold true and the junction temperature should remain below +120˚C except for the 5V output option.
The 5V option requires that T
A
+60˚C.
Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 kresistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin.
Note 4: Typical numbers are at 25˚C and represent the most likely norm. Note 5: All limits guaranteed at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are 100% tested
or guaranteed through statisticalanalysis.All limits at temperature extremes are guaranteed by correlation using standard Statistical Quality Control methods (SQC). All limits are used to calculate Average Outgoing Quality Level (AOQL).
Note 6: The V
OUT
pin is forced to 200 mV above the typical V
OUT
. This is to insure that the internal switches are off.
Note 7: The output capacitor C
OUT
is fully discharged before measurement.
Typical Performance Characteristics Unless otherwise specified T
A
= 25˚C.
V
OUT
vs. V
IN
DS200188-41
V
OUT
vs. V
IN
DS200188-42
LM3354
www.national.com 4
Loading...
+ 8 hidden pages