NOYAFA NF-HDMI User Manual

Download

Page 1

Your excellent helper in cable test!

MOD EL:NF -HDMI

INSTRUCTION MANUAL INSTRUCTION MANUAL INSTRUCTION MANUAL INSTRUCTION MANUAL

HDMI Cable Tester

RIGI N

AUTH ENTI

ENTI C

RE V1 .0

Page 2

DESCRIPTION

The Noyafa NF-HDMI HDMI Cable Tester is designed for professional HDMI installations. This portable device allows installers to quickly test, troubleshoot, and verify HDMI (high definition multimedia interface) cables.NF-H DMI is designed to test wire circuit state of HDMI cables with Type A & C connectors conforming to 1.0, 1.1, 1.2, 1.2a, 1.3, 1.3a, 1.3b,

1.3c, 1.4, 1.4a Category 1 and Category 2 cables. Equipped with 3 test modes, Automatically fast/slow scan or manual test for step by step, this tool can either test the conductors in straight、short、open、crossover in all RGB conductors.

SAFETY INFORMATION

Safety is essential in the use and maintenance of NOYAFA equipment. This instruction manual and any markings on the tool provide information for avoiding hazards and unsafe practices related to the use of this tool. Observe all of the safety information provided.

Warnings

●

Do not connect tester to a live circuit as it may

damage the unit.

It is easy to damage this tester with charged HDMI lines.

●

Caution

●

Read all instructions in this manual before using this tester. Failure to do so may result in damage to the tester or injury to the user.

●

Do not drop or get the unit wet. Do not expose tester to extreme humidity or direct sunlight.

Your excellent helper in cable test!

Page 3

●

Do not use this tester with its case open, or with parts removed. Doing so may damage the tester and/or injure the user.

●

Repairs and maintenance must only be carried out by qualified service personnel or qualified electricians/ technicians who know the dangers.

Follow the recommendations of any Trade

●

Organizations or Regulatory Agencies whose scope encompasses the use of this tester or injury to the user.

Remove the battery when the tester not in use for

●

longer than a month. Chemical leakage from the battery could damage the tester.

Please use batteries according to the specification;

●

otherwise it may result in damage to equipment.

CONTENTS

Your NF-HDMI HDMI Cable Tester contains the following

1. 1 x Master unit.

2. 1 x Remote unit.

3. 1 x Pouch bag.

4. Users' Manual.

FEATURES:

The NF-HDMI HDMI cable tester allows the fast and accurate verification both HDMI type A and Type C cables, mapping continuity and proper configuration and displays 19 pins and shield connection status on both main and remote unit.

Your excellent helper in cable test!

Page 4

For HDMI cables Type A, C

Test all HDMI cables with Type A to A, A to C and C to C connectors, especially for fragile, easily damaged HDMI patch cord and in-wall HDMI cables.

Loopback function

Design with loopback function allows test HDMI type A to A, A to C on main unit.

2 Test Modes

●

Fast continuity scans for testing all conductors'

status in a cable.

●

Slow continuity scans for testing all conductors'

status in a cable.

HDMI Cable Mapping

Automatically detect wiring on HDMI type A or type C condition in straight、short、open、crossover in pin #1~#19 and Shield conductor.

Troubleshooting

Quickly troubleshoot and verify HDTV installation and DIY termination in the field.

Your excellent helper in cable test!

Page 5

SPECIFICATIONS:

●

Cables Tested:HDMI cables with Type A & C

connectors conforming to 1.0, 1.1, 1.2, 1.2a, 1.3, 1.3a,

1.3b, 1.3c, 1.4, 1.4a Category 1 and Category 2 cables.

●

Support test (main unit and remote unit):

19 pin-to-pin wire map and shielding detection.

●

Test interface of Master unit:

HDMI (type A) ×1 pcs, Mini HDMI (type C) ×1 pcs.

●

Test interface of Remote unit:

HDMI (type A) ×1pcs, Mini HDMI (type C) ×1 pcs.

●

Cable length:Under 50 meters.

●

Test Mode:

Automatically fast scan、Automatically Slow scan.

●

Displays:

19 LEDs and shield LED on both main and remote unit.

●

Beeper indication.

●

Low battery indication:Under 6.0V

●

Power source:

DC 9V(NEAD 1604/6F22)×1 (not included)

●

Dimension:

Main unit:103×66×27,Remote unit：103×35×27 mm

●

Weight:130g (not incuding battery)

●

Operating environment:

32ºF to 104ºF (0ºC to 40ºC)＜80% RH

●

Storage environment:

14ºF to 122ºF (-10ºC to +50ºC)＜70% RH

Your excellent helper in cable test!

Page 6

PRODUCT DIAGRAM(Fig 1)

1.Mini MAIN:Mini-HDMI (C Type) This socket can be used on Master unit loopback test Remote unit Mini-HDMI (C Type) to perform scan test.

2.MAIN:HDMI (A Type)

3.Remote unit:HDMI (A Type)

4.Remote unit:Mini-HDMI (C Type)

5.Switch:CONTINUITY/OFF/SWEEP

6.Power and low battery indication.

7.HDMI (A Type) Pin number.

8.Mini-HDMI (C Type) Pin number.

9.LED for indicating signal situation.

1 3

C p

A p

A pin

C pin

Clock S

ta 2

Clock -

ta 2

CEC

a 2

Uti

. /

es.

Dat

a 1

SCL

a 1

SDA

ata 1

/ CE

D ata 0

V Powe

ata 0

t P

lug

Dat

a 0

i el

l o

c k +

C p

ck S

ta 2

lock -

Dat

a 2S

ata 2-

es.

Data 1+

ta 1

a 1

D D

ata 0+

V P

Data 0S

Hot Plu

Data 0-

ield

k +

Mast er U ni t Remo te U ni t

Fig 1

Your excellent helper in cable test!

Page 7

HDMI Cable Wire / Pin And Signal Description:

HDMI

(A)Pin #

1 2 3 4 5 6 7 8 9

14 15 16

18 19

MINI-HDMI

11 10 12

17 15 16

18 19

1 3 5 4 6 8 7 9

Assignment

Data 2+

Data 2S

TMD S Re d Da ta S hi el d

Data 2-

TMD S Re d Da ta M in us

Data 1+

TMD S Gr ee n Da ta P lu s

Data 1S

TMDS Green Data Shield

Data 1-

TMDS Green Data Minus

Data 0+

TMD S Bl ue D at a Sh ie ld

Data 0S

TMD S Bl ue D at a Mi nu s

Data 0-

Clock +

Clock S

Clock -

Consu me r El ec troni cs

CEC

Reser ve d

DDC/C EC

+5V Pow er

Contr ol

SCL

SDA

Data shield for the display data channel and consumer electronics control

Hot Plu g

Shied

Signal Description

TMD S Re d Da ta P lu s

TMD S Bl ue D at a Pl us

TMD S Cl oc k Pl us

TMD S Cl oc k Sh ie ld

TMD S Cl oc k Mi nu s

Uti li ty /R es erved

Seria l Cl oc k

Seria l Da ta

+5V Pow er

Hot Plu g De te ct

Shied

Your excellent helper in cable test!

Page 8

Correspo nding to the Pins Defin ition of the HDMI cable s(Fig 2)

151719

1618

135791113

2468101214

(Fig 2)

OPER ATION

Note

When all LEDs are lighted all LEDs will decrease

●

brightness.

●

Master unit shorted pins LED will be brighter than

others when shorted 2 pins above that is correct.

●

Shield LED will light up after #1~19 LEDs light up

in sequence on any testing mode. If the HDMI cable has a shield, the Shield LED will light up, if without shield the LED will be unlighted.

Powe r of f:

Slide u pp er l ef t sw itc h to “ OF F” , POW ER ”L ED will go o ut .

“

Your excellent helper in cable test!

Page 9

Note Mast er u ni t wi th R emote uni t au to ma ti c test in g fu nc ti on

※ Insert one of A type connector of cable to Master

unit MAIN (A Type) socket and insert the other one to Remote unit A Type connector for test HDMI cable A type to A type. ※ Insert A type connector to Master unit LOOPBACK

(A Type) and insert C type connector to Remote unit Mini-HDMI (C Type) for test HDMI cable A type to Mini-HDMI (C Type). ※ Insert one of C type connectors of cable to Master

unit Mini-HDMI (C Type) socket and insert the other one to Remote unite (C Type) socket for test HDMI cable Mini-HDMI (C Type) to Mini-HDMI (C Type) socket.

1.Slide upper left switch to “CONTINUITY” then “POWER” LED lights up. Master unit #1~19 and “Shield” LEDs will all light up

2.LED indicates test result as below:

●

Straight:Master unit and Remote unit both testing pin #1~19 and “Shield” LEDs are all lighted up. (Fig 3.)

Open:Master unit and Remote unit both no

●

connected pins LEDs are off. (Fig 4.)

Your excellent helper in cable test!

Page 10

Short:Master unit testi ng s ho rt p in L ED s br ig ht er

●

than others. Remote unit shorted pins LEDs are off.

(Fig 5.)

Crossover:It can't be tested on this mode.(Fig 6. )

●

Mast er unit w ith R emote u nit slo w cont inuit y sca n testi ng func tion:

1.LED indicate testing result as below:

●

Straight:Master unit an d Re mo te u ni t bo th t es ti ng pins #1~19 and Shield LEDs are all lighted up in sequence. (Fig 3.)

Cloc k S

Cloc k -

CEC

SCL

SDA

Shie ld

Data 2 +

Data 2 S

Data 2 -

Data 1 +

Data 1 S

Data 1 -

Data 0 +

Data 0 S

Data 0 -

Cloc k +

A pin

C pin A pin C pin

Cloc k S

Cloc k -

CEC

Uti. /Res.

SCL

SDA

DDC/ CEC

+5V Po wer

Hot Pl ug

Shie ld

A pin

Data 2 +

Data 2 S

Data 2 -

Data 1 +

Data 1 S

Data 1 -

Data 0 +

Data 0 S

Data 0 -

Cloc k +

C pin A pin C pin

Uti. /Res.

DDC/ CEC

+5V Po wer

Hot Pl ug

S S

Fig 3 . St ra ig ht

Your excellent helper in cable test!

Page 11

●Open:Master unit and Remote u ni t bo th L ED s ar e

off w he n ca n to n o co nn ec te d pi ns , ot he rs L ED s ar e all lighted up in sequence. Example : Test HD MI (A Type ) to H DM I (A Typ e) c ab le t ha t pi n #2、# 5、 #8、#11 are n ot c on ne ct ed , or t es t HD MI ( A Type ) to Mini-HDMI (C Typ e) c ab le t ha t pi n #1、# 4、#7、# 10 are not connected, or test Mini-HDMI (C Type ) to Mini-HDMI (C Typ e) c ab le t ha t pi n #1、# 4、#7、# 10 are not connected. (Fig 4.)

C pin A pin C pin

Cloc k S

Cloc k -

CEC

Uti. /Res.

SCL

SDA

DDC/ CEC

+5V Po wer

Hot Pl ug

S S

Shie ld

Your excellent helper in cable test!

A pin

Data 2 +

Data 2 S

Data 2 -

Data 1 +

Data 1 S

Data 1 -

Data 0 +

Data 0 S

Data 0 -

Cloc k +

Fig 4 . Op en

C pin A pin C pin

Cloc k S

Cloc k -

CEC

Uti. /Res.

SCL

SDA

DDC/ CEC

+5V Po wer

Hot Pl ug

Shie ld

A pin

Data 2 +

Data 2 S

Data 2 -

Data 1 +

Data 1 S

Data 1 -

Data 0 +

Data 0 S

Data 0 -

Cloc k +

Page 12

●Short:Master unit LED brighte r th an o th er s an d

Remote unit LED off w he n sc an t o sh or te d pi ns , Master unit and Remote unit both LED are all lighted up in sequence, Example : Test HD MI ( A Type ) to HDMI (A Type) c ab le t ha t pi n #4、# 5、#6 a re s ho rt ed , or teat HDMI (A Type) t o Mi ni -H DM I (C Ty pe ) ca bl e that pin #4、#5、#6 are shorted, or test Mini-HDMI (C Typ e) t o Mi ni -H DM I (C Ty pe ) ca bl e th at p in # 4、 #5、#6 are shorted. (Fig 5.)

Cloc k S

Cloc k -

CEC

SCL

SDA

Shie ld

Data 2 +

Data 2 S

Data 2 -

Data 1 +

Data 1 S

Data 1 -

Data 0 +

Data 0 S

Data 0 -

Cloc k +

A pin

C pin A pin C pin

Cloc k S

Cloc k -

CEC

Uti. /Res.

SCL

SDA

DDC/ CEC

+5V Po wer

Hot Pl ug

Shie ld

A pin

Data 2 +

Data 2 S

Data 2 -

Data 1 +

Data 1 S

Data 1 -

Data 0 +

Data 0 S

Data 0 -

Cloc k +

C pin A pin C pin

Uti. /Res.

DDC/ CEC

+5V Po wer

Hot Pl ug

S S

Fig 5 . Sh or t

Your excellent helper in cable test!

Page 13

●

Crossover:Master unit LEDs ligh t up i n se qu en ce and Remote unit LEDs light up sequence by crossed pins, Example : test HDMI (A Type ) to H DM I (A Typ e) cable that pin #13 with pin#17 are crossed and pin #14 with pin #19 are crossed, or test HDMI (A Type) to Mini-HDMI (C Type ) ca bl e pi n #1 4 wi th p in # 13 and pin #17 with pin #19 are crossed, or test Mini-HDMI (C Typ e) t o Mi ni -H DM I (C Ty pe ) ca bl e pin #14 with pin #13 are crossed and pin #17 crossed with #19 are crossed. (Fig 6.)

C pin A pin C pin

Cloc k S

Cloc k -

CEC

Uti. /Res.

SCL

SDA

DDC/ CEC

+5V Po wer

Hot Pl ug

S S

Shie ld

Your excellent helper in cable test!

A pin

Data 2 +

Data 2 S

Data 2 -

Data 1 +

Data 1 S

Data 1 -

Data 0 +

Data 0 S

Data 0 -

Cloc k +

Fig 6 . Cr os so ve r

C pin A pin C pin

Cloc k S

Cloc k -

CEC

Uti. /Res.

SCL

SDA

DDC/ CEC

+5V Po wer

Hot Pl ug

Shie ld

A pin

Data 2 +

Data 2 S

Data 2 -

Data 1 +

Data 1 S

Data 1 -

Data 0 +

Data 0 S

Data 0 -

Cloc k +

Page 14

BATTERY LI FE AND R EPL ACEME NT:

Caut io n

To avoid unreliable test results, replace the battery as soon as the low battery indication appears.

War ni ng s

To avoid possible electric shock or personal injury, turn off th e ma st er u ni t an d di sc on ne ct a ll t es t le ad s before replacing the battery.

Batt er y St at us :When ”PO WE R/ LO W BAT T.” LED is f la sh in g on t he master u ni t, i t me ans the ba tt er y vo lt age is unde r 6. 0V w hi ch couldn 't powe r th e de vi ce o n. Please r ep la ce t he batter y as the f ol lo wi ng s tep:

1.Tu rn o ff t he m as te r unit and di sc on ne ct all test lead s be fo re r ep lacing th e ba tt er y.

2.Pro pe rl y re pl ace the bat te ry i nt o the batt er y ca se .

3.Use o nl y a DC 9 V( NE AD 1604/6 F2 2) b at tery.

HDMI ® is a r eg is te red trade ma rk o f HD MI Lice ns in g, L LC .

Your excellent helper in cable test!

Page 15

NF- 306 NF- 868 N F- 82 08

NF- 268 NF- 806R

NF- 468L NF- 3468 NF8 108-M

NF- 388 NF- 903 NF- 906A

Your excellent helper in cable test!

NF- 816

Page 16

Your excellent helper in cable test!

SHENZHEN NOYAFA ELECTRONIC CO.,LTD