Nova-Tech Anti-Vibration Table User Manual

[e-mail]

CALL Toll Free: 1-866-433-6682 or 1-281-359-8538

www.novatech-usa.com

FAX Toll Free: 1-866-433-6684 or 1-281-359-0084

Adam Equipment

ANTI-VIBRATION TABLE

(P.N.8035, Rev. A4, June 2007)

© Adam Equipment Company 2007

[e-mail]

CALL Toll Free: 1-866-433-6682 or 1-281-359-8538

www.novatech-usa.com

FAX Toll Free: 1-866-433-6684 or 1-281-359-0084

1.0 INTRODUCTION

The Adam Anti-Vibration Table is designed for use in the laboratory or
metrology room to provide suitable working conditions for devices that
are sensitive to vibrations and shocks.

The table comprises two separate parts-

• An internal working surface consisting of a large marble slab
mounted on rubber shock absorbing mounts

• An external service table with steel frame and adjustable levelling
feet

2.0 TECHNICAL SPECIFICATIONS

Overall dimensions (w x d x h) 800 x 600 x 782 mm
Work Surface dimensions 400 x 450 mm
Weight of Work Surface 48 kg
Total weight 82 kg

© Adam Equipment Company 2007

2

[e-mail]

CALL Toll Free: 1-866-433-6682 or 1-281-359-8538

www.novatech-usa.com

FAX Toll Free: 1-866-433-6684 or 1-281-359-0084

4.0 SETTING UP THE TABLE

4.1 PACKING LIST

No. NAME QTY

1 MARBLE 1
2 RUBBER 4
3 INNER TABLE RAIL(SMALL) 3
4 M8×16 SCREW 28
5 MARBLE SUPPORT RAIL 2
6 INNER TABLE SIDE ASSEMBLY(SMALL) 2
7 ADJUSTABLE FOOT 4
8 FRONT TRIM PANEL 1

9 Z-CLIP 4
10 M8×8 SCREW 4
11 TABLE TOP 1
12 MAIN TABLE RAIL (LARGE) 2
13 MAIN TABLE SIDE ASSEMBLY(LARGE) 2
14 HEXAGON SPANNER 1

© Adam Equipment Company 2007

3

4.2 INNER TABLE ASSEMBLY DIAGRAM

[e-mail]

CALL Toll Free: 1-866-433-6682 or 1-281-359-8538

www.novatech-usa.com

FAX Toll Free: 1-866-433-6684 or 1-281-359-0084

Assembly instructions:

1. Assemble the 3 x INNER TABLE RAILS using the HEXAGON
SPANNER with twelve M8 x 16 screws onto the 2 x INNER TABLE
SIDE ASSEMBLIES. Pay attention that the rails are assembled with
the holes facing downwards.

2. Assemble the MARBLE SUPPORT RAILS using four M8 x 16 screws
onto the INNER TABLE RAILS.

3. Assemble the four ADJUSTABLE FEET into the MARBLE SUPPORT
RAILS and then add the four RUBBERS to the ADJUSTABLE FEET.

4. Place the MARBLE onto the RUBBERS making sure that the marble

is centrally located.

© Adam Equipment Company 2007

4

4.3 MAIN TABLE ASSEMBLY DIAGRAM

[e-mail]

CALL Toll Free: 1-866-433-6682 or 1-281-359-8538

www.novatech-usa.com

FAX Toll Free: 1-866-433-6684 or 1-281-359-0084

Assembly instructions:

1. Assemble the FRONT TRIM PANEL using four M8 x 16 screws onto
the 2 x MAIN TABLE SIDE ASSEMBLIES.

2. Fix the 2 x TABLE RAILS using eight M8 x 16 screws onto the MAIN
TABLE SIDE ASSEMBLIES.

3. Put the TABLE TOP onto the main frame using the four Z-CLIPS and
four M8 x 16 screws. Two Z-CLIPS should be fitted and secured first
and then the other two can be fitted when the table top is in place
from underneath. Make sure that the table top is fitted squarely.

4. Now place the MAIN TABLE over the top of the INNER TABLE
making sure that the marble is not touching the table top.

5. The feet can now be adjusted to level the tables. NOTE:

For
weighing a larger unit that is larger than the marble slab area, we
suggest you raise the marble slab a few millimetres higher than
the table top so that the overhang portion of the unit does not
touch the table top.

© Adam Equipment Company 2007

5

4.4 COMPLETED ANTI VIBRATION TABLE

[e-mail]

CALL Toll Free: 1-866-433-6682 or 1-281-359-8538

www.novatech-usa.com

FAX Toll Free: 1-866-433-6684 or 1-281-359-0084

5.0 MAINTENANCE

• Do not dismantle the Anti-Vibration table without following the
assembly instructions.

• Do not move the Anti-Vibration Table violently and abruptly. It
is recommended to move and put down the Table gently.

• It is suggested to wipe the stains with soft cloth soaked with
detergent. Do not use organic solutions and boiled water to
wipe the stains. Do not use water for cleaning.

• Keep the Anti-Vibration Table in a dry and clean environment.
Do not expose it outdoor or use it in locations near fire, under
direct sunshine or with high temperature.

© Adam Equipment Company 2007

6

[e-mail]

CALL Toll Free: 1-866-433-6682 or 1-281-359-8538

www.novatech-usa.com

FAX Toll Free: 1-866-433-6684 or 1-281-359-0084

WARRANTY INFORMATION

Adam Equipment offers Limited Warranty (Parts and Labour) for the components
failed due to defects in materials or workmanship. Warranty starts from the date of
delivery.

During the warranty period, should any repairs be necessary, the purchaser must
inform its supplier or Adam Equipment Company. The company or its authorised
Technician reserves the right to repair or replace the components at any of its
workshops depending on the severity of the problems. However, any freight involved
in sending the faulty units or parts to the service centre should be borne by the
purchaser.

The warranty will cease to operate if the equipment is not returned in the original
packaging and with correct documentation for a claim to be processed. All claims
are at the sole discretion of Adam Equipment.

This warranty does not cover equipment where defects or poor performance is due
to misuse, accidental damage, exposure to radioactive or corrosive materials,
negligence, faulty installation, unauthorised modifications or attempted repair or
failure to observe the requirements and recommendations as given in this User
Manual.

Repairs carried out under the warranty does not extend the warranty period.
Components removed during the warranty repairs become the company property.

The statutory right of the purchaser is not affected by this warranty. The terms of
this warranty is governed by the UK law. For complete details on Warranty
Information, see the terms and conditions of sale available on our web-site.

© Adam Equipment Company 2007

ADAM EQUIPMENT is an ISO 9001:2000 certified global organisation with more than 30

[e-mail]

CALL Toll Free: 1-866-433-6682 or 1-281-359-8538

www.novatech-usa.com

FAX Toll Free: 1-866-433-6684 or 1-281-359-0084

years experience in the production and sale of electronic weighing equipment. Products are
sold through a world wide distributor network supported from our company locations in the
UK, USA, SOUTH AFRICA and AUSTRALIA.

ADAM’s products are predominantly designed for the Laboratory, Educational, Medical and
Industrial Segments. The product range is as follows:

-Analytical and Precision Laboratory Balances

-Counting Scales for Industrial and Warehouse applications

-Digital Weighing/Check-weighing Scales

-High performance Platform Scales with extensive software
features including parts counting, percent weighing etc.

-Crane scales for heavy-duty industrial weighing

-Digital Electronic Scales for Medical use

-Retail Scales for Price computing

Adam Equipment Co. Ltd.

Bond Avenue

Milton Keynes

MK1 1SW

UK

Tel:[phone]

Fax: [phone]

E-mail:

[e-mail]

Adam Equipment Inc.

26, Commerce Drive

Danbury, CT

06810

USA

Tel: [phone]

Fax: [phone]

E-mail:

[e-mail]

Adam Equipment S.A. (Pty) Ltd.

7 Megawatt Road,

Spartan EXT 22, Kempton Park,

Johannesburg

Republic of South Africa
Tel: [phone]

Fax: [phone]

E-mail:

[e-mail]

Adam Equipment (S.E. ASIA)

2/71 Tacoma Circuit

Canning Vale, Perth

Western Australia

Tel: [phone]

Fax: [phone]

[e-mail]

Pty Ltd.

E-mail:

© Copyright by Adam Equipment Co. Ltd. All rights reserved. No part of this

publication may be reprinted or translated in any form or by any means without the

prior permission of Adam Equipment.

Adam Equipment reserves the right to make changes to the technology, features,

specifications and design of the equipment without notice.

All information contained within this publication is to the best of our knowledge

timely, complete and accurate when issued. However, we are not responsible for

misinterpretations which may result from the reading of this material.

The latest version of this publication can be found on our Website.

Visit us at www.adamequipment.com

© Adam Equipment Company 2007