INSTRUCTION MANUAL
Version 1.0
12/15/2010
INSTRUCTION MANUAL
TABLE OF CONTENTS
Product Overview ....................................................................................................................... 3
Items Included ........................................................................................................................... 3
Precautions ................................................................................................................................ 4
Minimum System Requirements ................................................................................................. 4
Software Installation ................................................................................................................. 5
Start Screen ............................................................................................................................ 5
Software Install ...................................................................................................................... 5
Software Registration ............................................................................................................. 6
NovaLink Instructions ................................................................................................................ 8
Startup .................................................................................................................................... 8
Creating & Saving a Profile ..................................................................................................... 9
Uploading/Updating a Profile .................................................................................................. 9
Resetting to Default Settings ................................................................................................ 10
Sharing Profiles ..................................................................................................................... 10
Disconnecting Your ESC ........................................................................................................ 10
Downloading Software Updates ............................................................................................ 10
ESC Firmware Upgrade ............................................................................................................. 11
NovaLink Parameter Definitions ............................................................................................... 12
Settings ................................................................................................................................. 12
Advanced .............................................................................................................................. 17
Comments & Suggestions ......................................................................................................... 19
Troubleshooting ....................................................................................................................... 19
ESC Disconnected During Firmware Update .......................................................................... 19
NovaLink Not Displaying Properly on Windows 7 .................................................................. 19
NovaLink Firmware Updater Displays Error Message ............................................................ 19
Product Warranty ..................................................................................................................... 20
Novak Electronics, Inc. www.teamnovak.com
|
2
PRODUCT OVERVIEW
INSTRUCTION MANUAL
The NovaLink
that easily plugs into the speed control and an included USB cord. Using the integrated software disk,
customers can fine tune the ESC’s multiple parameters by inputting the desired values or using the userfriendly graphic controls. Additionally, each personalized set of parameters can be stored on a PC to recall
and use again later. These custom-made parameter sets can, also, be shared with other drivers. The
NovaLink will never be outdated due to the easy-to-download software updates available to users on
Novak’s Web site. The NovaLink is compatible with Windows® XP™, Vista™, and 7™ computer-operating
platforms.
TM
provides users with expanded programming adjustability. It comprises a unique module
ITEMS INCLUDED
1. NovaLink USB Adaptor Module
2. USB Cable
3. NovaLink Software Disk
Novak Electronics, Inc. www.teamnovak.com
|
3
INSTRUCTION MANUAL
MINIMUM SYSTEM REQUIREMENTS
Please ensure that the computer you plan to install NovaLink on meets the following minimum
requirements
Operating System
Memory 512 RAM
CPU 1 GHz Processor
Disk 100 MB Disk
Graphics VGA Card (800x600 minimum resolution recommended)
The NovaLink uses a period (.) as the standard decimal separator. This software will not run if a
comma (,) is used instead.
whereas the US and English countries use the period).
(Some European countries use the comma as the standard decimal separator,
Windows®XPTM32-bit, Vista
The NovaLink is not compatible with 64-bit operating systems
TM
32-bit , 7
TM
32-bit
PRECAUTIONS
Check for Firmware Updates!
It is important to make sure you have the latest ESC firmware. (Refer to the “ESC Firmware Upgrade
section of this manual).
Check for Software Updates!
It is important to make sure you have the latest NovaLink software updates. (Refer to the “Downloading
Software Updates” section of this manual).
Always Unplug the ESC Fan Before Running NovaLink or Firmware Update!
Please remember to always unplug the ESC fan before using NovaLink or ESC Firmware Upgrade. Leaving
the fan plugged in will result in excess current draw that may disable the USB port and electrical noise
generated by the fan may interfere with communication.
Water and Electronics Don’t Mix!
Never allow water, moisture or other foreign materials to get inside the speed controller or the NovaLink.
Water damage will void the product warranty!
Do NOT put the NovaLink pins close to other metal objects!
Putting the metal pins against another metal object can result in shorting the NovaLink circuit. This
damage is not covered under the product’s warranty.
Plug the ESC into the NovaLink Correctly and Carefully!
The metal pins on the NovaLink can be damaged easily if the ESC is not
plugged into the Novalink carefully. The pins are marked with ”White”
and “Black” labels to aid in connecting your ESC correctly. Make sure to
match the labels on the NovaLink module with the color of the wires on
the ESC as shown in the image to the right.
White
Black
”
Novak Electronics, Inc. www.teamnovak.com
|
4
INSTRUCTION MANUAL
SOFTWARE INSTALLATION
1. Insert the NovaLink CD
Start Screen
• Windows XP: If AutoRun is enabled on your computer, the
NovaLink Start Screen will automatically open in your browser.
• Windows Vista & 7: An AutoPlay options window will usually
be displayed. Click “Run NovaLink_Startup.html”
If the Start Screen does not display when the CD is inserted,
navigate to My Computer -> right-click “NovaLink” -> select
“Open” -> double-click NovaLink_Startup.html
Software Install
1. Click Start -> My Computer (or -> Computer)
2. Double-click the NovaLink icon
3. Double-click the Drivers folder
4. Install the drivers
a. Windows XP: double-click the file “NovaLink_Drivers”
b. Windows Vista & 7: right-click “NovaLink_Drivers” and click “Run as Administrator”
i. A black command prompt will pop up during installation
5. Once the black command prompt disappears, plug the NovaLink into the USB
6. Return back to the NovaLink Setup folder by clicking the “Back” button
7. Double-click the Installer folder
8. Install NovaLink by double-clicking on the Setup.exe file
Click “Next” to begin the NovaLink Setup Wizard
Novak Electronics, Inc. www.teamnovak.com
|
5
The default installation folder is “C:\Program Files\Novak
Electronics\NovaLink_M2Dig\”. To change the installation
folder, type in the folder path or click “Browse” to select a
folder
Click “Next” to continue with the installation
INSTRUCTION MANUAL
Click “Next” to begin installation
Software Registration
After installation, you can register your software by
clicking “Register Now” or if you plan to skip registration,
click “Next”.
The registration form can be found by navigating to
Start -> All Programs -> Novak Electronics.
Registering your NovaLink will ensure that you receive emails from Novak when new versions of the software or
firmware are available.
Novak Electronics, Inc. www.teamnovak.com
|
6
Once the installation is complete, click “Close” to exit the
installation wizard
INSTRUCTION MANUAL
Novak Electronics, Inc. www.teamnovak.com
|
7
g
,
g
INSTRUCTION MANUAL
NOVALINK INSTRUCTIONS
Startup
1. Make sure to have your USB cable, NovaLink USB Adaptor, and ESC
ready
2. Plug the USB cable into your computer’s USB port
3. Plug the NovaLink adapter into the USB cable
NOTE: Make sure you unplug both input harnesses before starting the
4. Unplug the two input harnesses from your receiver (Figure 1)
5. Unplug the ESC fan & battery
6. Plug the throttle harness into the NovaLink adapter (Figure 2)
7. Start the NovaLink program
8. If you are ready to upload and configure your ESC settings, refer to the Uploading
/Updating a Profile section
Always unplug the ESC fan AND battery before running NovaLink or the ESC
Firmware Upgrade! (refer to Precautions
NovaLink software!
for details)
Figure 1
Figure 2
Any time One-Touch programming is performed, the speed controller will automatically revert back to factorydefault settings. The only exception is when the Timing settings are programmed via the NovaLink. These
settings are kept in the ESC’s non-volatile memory and when you connect the ESC to the NovaLink, the
following values will be uploaded from the ESC non-volatile memory:
- Timing Set Point
- Max Timing RPM
- Timing Level
- Boost Mode
- Boost Delay
When the ESC is powered up it goes through the following sequence:
1. All five LEDs light up during an internal test cycle.
2. Blue and green LEDs light up while the ESC is looking for the NovaLink. During this time, it is sending
out messages through the input harness and is expecting a return message from the NovaLink. If no
messages are received by the ESC, it times out.
3. Red and yellow LEDs blink twice to indicate Li-poly mode.
4. If the ESC is connected to a receiver and the signal is present, the red, yellow and blue LEDs light up
to indicate that the Neutral PPM signal is present and the Drag brake is enabled (if Timing is enable,
the white LED will also light up).
5. If no si
nal is present
the red and green LEDs will li
ht up.
Novak Electronics, Inc. www.teamnovak.com
|
8
MENU ICONS
Create New Profile
Open Existing Profile
Save Current Profile Suggestion Box
Creating & Saving a Profile
1. Click the Create New Profile icon on the menu bar
2. Adjust settings (refer to “NovaLink Parameter
Definitions”)
3. Click the Save Current Profile icon on the menu
bar
4. Choose a location to save the current profile
5. Type in next to File Name the name you would like to
name this profile
6. Click Save (all parameters on both the “Settings” and
“Advanced” tabs are saved)
INSTRUCTION MANUAL
Firmware Updater
About Us
NOTE: You do NOT need to have your ESC connected to create and save a profile
Uploading/Updating a Profile
1. Adjust settings (refer to “NovaLink Parameter
Definitions”)
2. Click Update to update your ESC’s settings (your ESC will
not be updated when you press Save)
(Your NovaLink interface will disconnect and reconnect
your ESC during this process)
a. Do NOT disconnect your ESC while it is updating
(refer to Disconnecting Your ESC
3. When the NovaLink screen re-appears, the updated profile
has been successfully saved to the ESC
)
Resetting to Default Settings
1. Click Reset in the top right corner of the interface
2. Resetting your profile will change all your parameters back
to its default values
3. If you plan on using these defaults for your ESC, do not forget to update your ESC (refer to
“Uploading/Updating a Profile
”)
Novak Electronics, Inc. www.teamnovak.com
|
9
Sharing Profiles
NovaLink allows users to share profiles by providing a feature
to open existing profiles. After receiving files from other users,
you can then upload them onto NovaLink to view the
parameters and use them on your own ESC.
1. Click the Open Exiting Profile icon
2. Select the profile you would like to open (.cfg)
3. Click Open
Disconnecting Your ESC
1. Click the Disconnect flag in the top toolbar
INSTRUCTION MANUAL
2. Remove your ESC when is shown
or
1. Close the program
2. Remove your ESC
Downloading Software Updates
Please visit http:// www.teamnovak.com/products/esc/m2 regularly for software updates. If you have
registered your NovaLink, we will notify you by e-mail when updates are available.
Novak Electronics, Inc. www.teamnovak.com
|
10
INSTRUCTION MANUAL
ESC FIRMWARE UPGRADE
It is important to keep your ESC firmware up to date. Visit www.teamnovak.com to check for new ESC
firmware upgrades. If your ESC firmware is ready for an upgrade, please follow these instructions on how
to upload the new firmware file and update your ESC:
1. Navigate to http://www.teamnovak.com/download/ESCFirmware
2. Download the M2 Dig Firmware zip file
3. Open the zip file
4. Double-click the EXE file
5. Unplug your ESC from the
NovaLink (if attached)
Note: make sure your ESC fan is unplugged
6. Start NovaLink
7. Click the Firmware Updater icon
8. The NovaLink Firmware Updater will now be launched
9. Click Update
10. Your ESC will now begin to update. When “ESC is now
updated” is shown, you may exit the application and
unplug your ESC
11
Do NOT disconnect your ESC from the NovaLink while the
firmware is updating. Your ESC will not be able to function
if this occurs. Restart the Firmware Updater and allow your
ESC to fully update if your ESC disconnects during the
firmware update.
(Refer to “Troubleshooting
Novak Electronics, Inc. www.teamnovak.com
|
” for details)
NOVALINK PARAMETER DEFINITIONS
Settings Tab
Dig Power - Dig Power is the amount of braking or dig power being applied to lock
either the front or rear motor.
- This setting is measured as a percentage of full brakes. Preset
selections are available in the drop down menu. Custom values can
entered in increments of 0.1%*.
- Increasing the Dig Power applies more braking power to the motor
that the Dig function is telling to lock. By locking either the front of
rear motor, the vehicle is able to perform a “Dig” maneuver than can
allow you to navigate around obstacles or perform a tighter turning
radius by dragging the rear wheels.
*You must select “Enter” for the software to recognize the custom value.
Drag/Hill Brake - Drag/Hill Brake is the amount of brake applied while the transmitter
is at neutral. It is also known as “coast brakes.”
- This setting is measured as a percentage of full brakes. Preset
selections are available in the drop down menu. Custom values can
entered in increments of 0.1%*.
- Increasing the Drag/Hill Brake setting makes the motor slow the
vehicle down more. You can adjust this setting to give the vehicle the
desired amount of creep down the incline when the transmitter’s
trigger is released.
- Drag/Hill Brake is featured in blue in the chart below. You can
graphically control the Drag/Hill Brake value by grabbing the bold
horizontal line in the blue section with your cursor and dragging it up
or down. This will also adjust the Minimum Brake value if the
Independent Drag Brake feature is set to “Off”.
INSTRUCTION MANUAL
*You must select “Enter” for the software to recognize the custom value.
Dead Band - Dead Band is the trigger space between Minimum Brake and
- This setting is measured as a percentage of full throttle. Ten preset
- Raising the Dead Band setting increases the amount of free play, or
Novak Electronics, Inc. www.teamnovak.com
|
12
Minimum Drive, with neutral in the middle.
selections are available in the drop down menu. Custom values can
be entered in increments of 0.1%*
distance you must move your transmitters trigger before forward
drive or braking activates. This setting is useful if your transmitters
trigger does not center well or the trigger pot is worn.
INSTRUCTION MANUAL
- The width of the blue section in the
chart below represents the Dead
Band.
* You must select "Enter" for the software
to recognize the custom value.
Drive Frequency - This setting controls how the speed control’s throttle (or forward
drive) responds to the transmitter’s trigger input. Drive Frequency is
the frequency at which the information is being sent from the ESC to
the motor (how many times per second the motor is being cycled on
and off to control its speed). Changing the Drive Frequency setting
can be a valuable tuning asset for different types of motors.
- This setting is measured in kHz. Preset selections are available in the
drop down menu. This parameter does not allow custom values to be
entered.
- Increasing the Drive Frequency setting will require more initial trigger
movement to obtain a given amount of forward drive. This will make
the throttle feel smoother and more controllable under initial drive.
Minimum Drive - Minimum Drive is the amount of forward drive applied with the first
pulse of transmitter throttle information.
- This setting is measured as a percentage of full throttle. Preset
selections are available in the drop down menu. Custom values can
entered in increments of 0.1%.
- Increasing the Minimum Drive setting starts the forward drive at a
stronger/higher level, causing the vehicle to take off more
aggressively from neutral. This is useful to compensate for heavier
vehicles to minimize the amount of trigger throw required before
effective drive is applied.
- Minimum Drive is featured in green in the chart below. You can
graphically control the Minimum
Drive value by grabbing the bold
horizontal line in the green section
with your cursor and dragging it
up or down.
*You must select “Enter” for the software to recognize the custom value.
Voltage Cut-Off - The Voltage Cut-Off setting enables or disables the speed control’s
Novak Electronics, Inc. www.teamnovak.com
|
13
Smart-Stop Voltage Cut-Off Circuitry and allows for the selection of
the type of batteries used in the vehicle’s main battery pack. The
Novak Smart-Stop Circuitry monitors battery voltage and folds back
power output to the motor when a critical voltage threshold is
reached for either LiPo or LiFe cells. Cutting off the power at the
critical threshold protects these batteries from being over-discharged
and damaged.
INSTRUCTION MANUAL
- This feature auto-selects the correct voltage cut-off value for the
number of cells in the main battery pack once the correct battery
type is selected.
WARNING: ALWAYS USE VOLTAGE CUT-OFF WITH LiPo AND LiFe
BATTERY PACKS. IF VOLTATGE CUT-OFF CIRCUITRY IS TURNED OFF AND
BATTERIES ARE ALLOWED TO DISCHARGE BELOW THE CELL’S CRITICAL
VOLTAGE, BATTERIES WILL BE DAMAGED.
Note: This feature is not accessible when the speed control is disconnected.
Operation Mode
Dig Mode
Default setting. When the transmitter’s AUX/3rd switch/dial is
thrown, the dig function for either the front or rear motor
(depending on the switch position) will be engaged, and the ESC
applies Dig Power (independent of Drag Brake) to lock the motor.
This mode requires a 3-channel transmitter with either a
proportional AUX/3rd channel switch or a simple three-position
switch to operate.
Proportional Dig Mode
In this mode, for any given partial throttle position, the
percentage of drive power applied to the affected motor is
reduced as the position of the AUX/3rd channel increases, while
the other motor receives its full amount of drive. When the
AUX/3rd channel nears full throw, the preset Dig Power is applied
to lock the affected motor. This mode requires a 3-channel
transmitter with a proportional-style AUX/3rd channel switch or
control similar to a dial or a knob.
Single Output Mode
This mode is used for standard 2-channel operation with either
single or dual-motor control. There is no dig function in this
profile.
Novak Electronics, Inc. www.teamnovak.com
|
14
COMMENTS & SUGGESTIONS
Team Novak welcomes all suggestions and comments! Feel free to send us
any suggestions or bugs you may have encountered through our
Suggestions form.
1. Start NovaLink
2. Click the Suggestions Box icon
3. Enter any suggestions, comments, or bugs into the text field
4. Click Send
TROUBLESHOOTING
INSTRUCTION MANUAL
ESC Disconnected During Firmware Update
1. Close the NovaLink Firmware Updater
2. Plug your ESC into the NovaLink Adaptor
3. Start the NovaLink Firmware Updater from the NovaLink program
4. Make sure your ESC fully updates
NovaLink Not Displaying Properly on
Windows 7
1. -> Control Panel -> Display
2. Change the setting to “Smaller-100%”
3. Click Apply
NovaLink Firmware Updater Displays
Error Message
If the Firmware Updater displays a popup saying “File does not exist. Make sure image is in the
C:\Program Files\Novak Electronics\NovaLink folder,” you need to download and save the firmware
file into the NovaLink folder. Refer to “ESC Firmware Upgrade
firmware file.
” for instructions on how to save the
Novak Electronics, Inc. www.teamnovak.com
|
15
INSTRUCTION MANUAL
PRODUCT WARRANTY
The NovaLink PC Interface software is guaranteed to be free from defects in materials or workmanship for
a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt).
Warranty does not cover incorrect installation, components worn by use, damage to the circuit board or
from excessive force or tampering with the internal electronics, exposing electronics to water, moisture, or
any other foreign material, allowing exposed wiring to short-circuit, or any damage caused by a crash,
flood, or other natural disaster.
Because Novak Electronics, Inc. has no control over the connection and use of the NovaLink Interface and
software or any other related electronics, no liability may be assumed, nor will be accepted, for any
damage resulting from the use of this product. Every Novak NovaLink PC Interface is thoroughly tested
before leaving our facility and is, therefore, considered operational.
By the act of connecting/operating the NovaLink PC Interface, user accepts all resulting liability. In no
case shall our liability exceed the product’s original cost. We reserve the right to modify warranty
provisions without notice.
This product is not intended for use by children under 14 years of age without the strict
supervision of an adult. Use of this product in an uncontrolled manner may result in physical
damage or injuries—take extra care when operating any remote control vehicle.
No part of these instructions may be reproduced without the written permission of Novak Electronics, Inc.
Microsoft, Windows XP, Windows Vista, and Windows 7 are trademarks of Microsoft Corporation in the U.S. and/or other countries.
NovaLink, Dynamic Timing Advance, and Electronic Power Control are trademarks of Novak Electronics, Inc.
Novak Electronics, Inc. www.teamnovak.com
|
16
17032 Armstrong Avenue
Irvine, Ca 92614
Phone: 949-833-8873
HUwww.teamnovak.comU
© 2010 Novak Electronics, Inc.
● All Rights Reserved ●
Loading...