Novak R/C, Inc. California • 2014 • Made in China • 55-583X-1.2
This pro duct con tain s chemicals whi ch a re k nown to the state o f
Californ ia t o ca use cancer, b irth def ects , or other repr oduc tive harm.
Novak R/C, Inc. California • 2014 • Made in China • 55-583X-1.2
This pro duct con tain s chemicals whi ch a re k nown to the state o f
Californ ia t o ca use cancer, b irth def ects , or other repr oduc tive harm.
Novak R/C, Inc. California • 2014 • Made in China • 55-583X-1.2
This pro duct con tain s chemicals whi ch a re k nown to the state o f
Californ ia t o ca use cancer, b irth def ects , or other repr oduc tive harm.
Specia lly formula ted Lead-Free Solder with 3% Silver
conten t for high- conductivit y, low-resi stance, & s trong
solder joints at a relativel y low melti ng point .
Envir onmentall y friendly & safe to handl e--Perfe ct for ha nd soldering.
SOLDERING TIPS
Always use a good, high-heat soldering iron.
Preparing The Wire: Strip the insulation from the end
of the wire. Tightly twist the exposed strands of wire.
Apply heat to exposed wire with iron and add solder to
the tip of the iron and to exposed wire at the same time.
Soldering The Wire: Pre-tin the surface being soldered
to. Place stripped & tinned end of wire on surface and
heat with iron--add just enough solder to form a clean
and continuous joint from the surface up onto the wire.
IMPORTANT NOTE
PROLONGED/EXCESSIVE HEATING WILL DAMAGE PC BOARDS
Novak R/C, Inc. California • 2014 • Made in China • 55-583X-1.2
This pro duct con tain s chemicals whi ch a re k nown to the state o f
Californ ia t o ca use cancer, b irth def ects , or other repr oduc tive harm.
Specia lly formula ted Lead-Free Solder with 3% Silver
conten t for high- conductivit y, low-resi stance, & s trong
solder joints at a relativel y low melti ng point .
Envir onmentall y friendly & safe to handl e--Perfe ct for ha nd soldering.
SOLDERING TIPS
Always use a good, high-heat soldering iron.
Preparing The Wire: Strip the insulation from the end
of the wire. Tightly twist the exposed strands of wire.
Apply heat to exposed wire with iron and add solder to
the tip of the iron and to exposed wire at the same time.
Soldering The Wire: Pre-tin the surface being soldered
to. Place stripped & tinned end of wire on surface and
heat with iron--add just enough solder to form a clean
and continuous joint from the surface up onto the wire.
IMPORTANT NOTE
PROLONGED/EXCESSIVE HEATING WILL DAMAGE PC BOARDS
Novak R/C, Inc. California • 2014 • Made in China • 55-583X-1.2
This pro duct con tain s chemicals whi ch a re k nown to the state o f
Californ ia t o ca use cancer, b irth def ects , or other repr oduc tive harm.
Specia lly formula ted Lead-Free Solder with 3% Silver
conten t for high- conductivit y, low-resi stance, & s trong
solder joints at a relativel y low melti ng point .
Envir onmentall y friendly & safe to handl e--Perfe ct for ha nd soldering.
SOLDERING TIPS
Always use a good, high-heat soldering iron.
Preparing The Wire: Strip the insulation from the end
of the wire. Tightly twist the exposed strands of wire.
Apply heat to exposed wire with iron and add solder to
the tip of the iron and to exposed wire at the same time.
Soldering The Wire: Pre-tin the surface being soldered
to. Place stripped & tinned end of wire on surface and
heat with iron--add just enough solder to form a clean
and continuous joint from the surface up onto the wire.
IMPORTANT NOTE
PROLONGED/EXCESSIVE HEATING WILL DAMAGE PC BOARDS
Novak R/C, Inc. California • 2014 • Made in China • 55-583X-1.2
This pro duct con tain s chemicals whi ch a re k nown to the state o f
Californ ia t o ca use cancer, b irth def ects , or other repr oduc tive harm.
Specia lly formula ted Lead-Free Solder with 3% Silver
conten t for high- conductivit y, low-resi stance, & s trong
solder joints at a relativel y low melti ng point .
Envir onmentall y friendly & safe to handl e--Perfe ct for ha nd soldering.
SOLDERING TIPS
Always use a good, high-heat soldering iron.
Preparing The Wire: Strip the insulation from the end
of the wire. Tightly twist the exposed strands of wire.
Apply heat to exposed wire with iron and add solder to
the tip of the iron and to exposed wire at the same time.
Soldering The Wire: Pre-tin the surface being soldered
to. Place stripped & tinned end of wire on surface and
heat with iron--add just enough solder to form a clean
and continuous joint from the surface up onto the wire.
IMPORTANT NOTE
PROLONGED/EXCESSIVE HEATING WILL DAMAGE PC BOARDS
Specia lly formula ted Lead-Free Solder with 3% Silver
conten t for high- conductivit y, low-resi stance, & s trong
solder joints at a relativel y low melti ng point .
Envir onmentall y friendly & safe to handl e--Perfe ct for ha nd soldering.
SOLDERING TIPS
Always use a good, high-heat soldering iron.
Preparing The Wire: Strip the insulation from the end
of the wire. Tightly twist the exposed strands of wire.
Apply heat to exposed wire with iron and add solder to
the tip of the iron and to exposed wire at the same time.
Soldering The Wire: Pre-tin the surface being soldered
to. Place stripped & tinned end of wire on surface and
heat with iron--add just enough solder to form a clean
and continuous joint from the surface up onto the wire.
IMPORTANT NOTE
PROLONGED/EXCESSIVE HEATING WILL DAMAGE PC BOARDS
Specia lly formula ted Lead-Free Solder with 3% Silver
conten t for high- conductivit y, low-resi stance, & s trong
solder joints at a relativel y low melti ng point .
Envir onmentall y friendly & safe to handl e--Perfe ct for ha nd soldering.
SOLDERING TIPS
Always use a good, high-heat soldering iron.
Preparing The Wire: Strip the insulation from the end
of the wire. Tightly twist the exposed strands of wire.
Apply heat to exposed wire with iron and add solder to
the tip of the iron and to exposed wire at the same time.
Soldering The Wire: Pre-tin the surface being soldered
to. Place stripped & tinned end of wire on surface and
heat with iron--add just enough solder to form a clean
and continuous joint from the surface up onto the wire.
IMPORTANT NOTE
PROLONGED/EXCESSIVE HEATING WILL DAMAGE PC BOARDS