Novak 55-5750-1.2 User Manual

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite
end connector (not on a battery pack) to help dissipate extra heat.

Insert the stripped & tinned end of the wire into the correct barrel
of the connector
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.

solder--again, being careful not to over-heat the connector’s plastic.

Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.

©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2

(“+” & “–” are marked on the side of connector)

If needed,

[phone] • Monday-Thursday

e-mail: [e-mail]

add a small amount of extra

. Heat

www. t e a mnova k . c o m

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

-

To avoid over-heating connector’s plastic, plug into a mating/opposite
end connector (not on a battery pack) to help dissipate extra heat.

Insert the stripped & tinned end of the wire into the correct barrel
of the connector
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.

solder--again, being careful not to over-heat the connector’s plastic.

Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.

©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2

(“+” & “–” are marked on the side of connector)

If needed,

[phone] • Monday-Thursday

e-mail: [e-mail]

add a small amount of extra

. Heat

-

www. t e a mnova k . c o m

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite
end connector (not on a battery pack) to help dissipate extra heat.

Insert the stripped & tinned end of the wire into the correct barrel
of the connector
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.

solder--again, being careful not to over-heat the connector’s plastic.

Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.

©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2

(“+” & “–” are marked on the side of connector)

If needed,

[phone] • Monday-Thursday

e-mail: [e-mail]

add a small amount of extra

. Heat

www. t e a mnova k . c o m

-

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite
end connector (not on a battery pack) to help dissipate extra heat.

Insert the stripped & tinned end of the wire into the correct barrel
of the connector
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.

solder--again, being careful not to over-heat the connector’s plastic.

Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.

©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2

(“+” & “–” are marked on the side of connector)

If needed,

[phone] • Monday-Thursday

e-mail: [e-mail]

add a small amount of extra

. Heat

www. t e a mnova k . c o m

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite
end connector (not on a battery pack) to help dissipate extra heat.

Insert the stripped & tinned end of the wire into the correct barrel
of the connector
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.

solder--again, being careful not to over-heat the connector’s plastic.

Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.

©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2

(“+” & “–” are marked on the side of connector)

If needed,

[phone] • Monday-Thursday

e-mail: [e-mail]

add a small amount of extra

. Heat

www. t e a mnova k . c o m

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

-

To avoid over-heating connector’s plastic, plug into a mating/opposite
end connector (not on a battery pack) to help dissipate extra heat.

Insert the stripped & tinned end of the wire into the correct barrel
of the connector
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.

solder--again, being careful not to over-heat the connector’s plastic.

Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.

©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2

(“+” & “–” are marked on the side of connector)

If needed,

[phone] • Monday-Thursday

e-mail: [e-mail]

add a small amount of extra

. Heat

-

www. t e a mnova k . c o m

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

-

To avoid over-heating connector’s plastic, plug into a mating/opposite
end connector (not on a battery pack) to help dissipate extra heat.

Insert the stripped & tinned end of the wire into the correct barrel
of the connector
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.

solder--again, being careful not to over-heat the connector’s plastic.

Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.

©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2

(“+” & “–” are marked on the side of connector)

If needed,

[phone] • Monday-Thursday

e-mail: [e-mail]

add a small amount of extra

. Heat

-

www. t e a mnova k . c o m

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite
end connector (not on a battery pack) to help dissipate extra heat.

Insert the stripped & tinned end of the wire into the correct barrel
of the connector
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.

solder--again, being careful not to over-heat the connector’s plastic.

Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.

©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2

(“+” & “–” are marked on the side of connector)

If needed,

[phone] • Monday-Thursday

e-mail: [e-mail]

add a small amount of extra

. Heat

www. t e a mnova k . c o m

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite
end connector (not on a battery pack) to help dissipate extra heat.

Insert the stripped & tinned end of the wire into the correct barrel
of the connector
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint.

solder--again, being careful not to over-heat the connector’s plastic.

Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.

©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2

(“+” & “–” are marked on the side of connector)

If needed,

[phone] • Monday-Thursday

e-mail: [e-mail]

add a small amount of extra

. Heat

www. t e a mnova k . c o m

-

-