North Star M1573001A User Manual

Page 1
Pump is shipped with oil.
- Remove shipping tape from pump oil fill cap. (Cat Pumps)
- Remove shipping plug and install vented fill cap. (Comet Pumps)
- See pump oil cap section of this manual.
Closely inspect all components.
-If you have damaged components: Contact the freight company that delivered the unit and file a claim.
-If you have missing components: Contact Customer Service at 1-800-270-0810.
Read this manual.
Serious injury or death can result if safety instructions are not followed.
WARNING
Item Numbers:
1573001,1573011
1573021
®
M1573001G.1
Owner’s Manual
Pressure Washer: Machine that cleans dirty surfaces
with high pressure water.
Any Questions, Comments, Problems or Parts Orders
Call NorthStar Product Support 1-800-270-0810
Page 2
Hazard Signal Word Definitions
2
Page 3
Table of Contents
3
Important Safety Instructions………………………..……...
4
Grounding Instructions……………………………………...
5
Warning Label Locations…………………………….……..
6
Assembly Instructions…………………………….………...
7-9
Machine Component Identification…………………………
10
Pump Component Identification…………………………….
11
Operation Instructions………………………………..……..
12-15
Water Supply………………………………………..…
12
Start-Up/Shut-Down Instructions……………………...
12
Spray Gun Safety Lock and Attaching the Lance……..
13
Installing Nozzles and Quick Connect hoses………….
14
Applying Chemicals…………………………………...
15
Maintenance and Storage……………………………………
16-18
Maintenance Mode and Maintenance Schedule……….
16
Pump Oil Change………………………………………
17
Winter Storage…………………………………………
18
Troubleshooting……………………………………………..
19
Specifications………………………………………………..
20
Wiring Diagram……………………………………………..
20-21
Parts Explosions…………………………………………….
22
Pump Exploded Views……………………………………...
24-27
Limited Warranty…………………………………………...
29
Page 4
Important Safety Instructions
4
WARNING - Risk of Injection or Injury to Persons - Do Not Direct Discharge Stream at Persons. -
Do not use a hose if exterior damage is evident.
- Risk of explosion. - Do not spray flammable liquids. - Do not operate in a flammable environment.
CAUTION - Gun kicks back. Hold with both hands.
- To reduce the risk of injury, read operating instructions carefully before use. WARNING - When using this product basic precautions should always be followed, including the following:
1.) Read all the instructions before using the product.
2.) To reduce the risk of injury, close supervision is necessary when the product is used near children. Do not allow irresponsible use by children. Always stop the product and bleed pressures before leaving unattended, disconnecting hoses or servicing the pump.
3.) Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls.
4.) Stay alert - watch what you are doing.
5.) Do not operate the product when fatigued or under the influence of alcohol or drugs.
6.) Keep operating area clear of all persons.
7.) Do not overreach or stand on unstable support. Keep good footing and balance at all times. Wear footwear capable of maintaining a good grip on wet surfaces - Do not place the machine on soft or unstable ground.
8.) Follow the maintenance instructions specified in all manuals. Do not run machine without sufficient lubrication or sufficient water to cool the pump.
9.) Wear safety glasses, gloves, face protection and appropriate clothing when operating the machine.
10.) Do not operate this machine with broken or missing parts. - Never alter the manufacturer’s original
design or deactivate any safety device on the machine.
11.) Risk of exposure to dangerous chemicals. Wear protective gloves when handling and cleaning with
chemicals. Follow the chemical manufacturer’s directions. Understand all safety hazards and first aid
for all chemicals being used. Check whether dangerous chemicals have been used and take any precautions that may have been recommended by the supplier of these chemicals when cleaning filters. Do not pump highly abrasive fluids or use with incompatible chemicals or solvents.
12.) Know the pressure and temperature limits of your machine. Be sure all high pressure accessories meet
or exceed your machine’s limits. Do not set the pressure relief valve above the machine’s limit.
13.) Do not move this machine by pulling on the hose. Do not use the pump to support other items of
equipment that impose unacceptable loads on the pump. Do not attempt to use this machine as a prop.
14.) To reduce risk of injury, do not secure the spray gun open. Your spray gun is equipped with a built-in
trigger safety latch to guard against accidental trigger release and potentially dangerous high pressure spray. Rotate the safety latch to the locked position when not spraying.
15.) Do not clean this machine with its own spray. Cleaning should be done with a damp sponge with the
motor OFF.
16.) Always make sure all switches and controls are in the OFF position prior to plugging in the electrical
cord. Do no stand in water while plugging and unplugging electrical cord.
17.) This product is provided with a ground fault circuit interrupter built into the power cord plug. If
replacement of the plug or cord is needed, use only identical replacement parts.
SAVE THESE INSTRUCTIONS
Page 5
Grounding Instructions
5
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment - grounding conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the product - if it will not fit the outlet; have a proper outlet installed by a qualified electrician. Do not use any type adapter with this product.
1. For a product rated 125 volts or less:
GROUND FAULT CIRCUIT INTERRUPTER PROTECTION
This pressure washer is provided with a ground fault circuit interrupter (GFCI) built into the plug of the power supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection.
2. For a product rated more than 125 volts:
GROUND FAULT CIRCUIT INTERRUPTER PROTECTION
To comply with the National Electric Code (NFPA 70) and to provide additional protection from the risk of
electric shock, this pressure washer should only be connected to a receptacle that is protected by a ground fault
circuit interrupter (GFCI).
Extension Cords
Use only 3-wire extension cords that have 3 prong grounding-type plugs and 3-pole cord connectors that accept the plug from the product. Use only extension cords that are intended for outdoor use. These extension cords are identified by a marking “Acceptable for use with outdoor appliances; store indoors while not in use.” Use only extension cords having an electrical rating not less than the rating of the product. Do not abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and sharp edges. Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord.
WARNING - To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch plug with wet hands.
SAVE THESE INSTRUCTIONS
Page 6
Warning Label Locations
6
START-UP INSTRUCTIONS
1. Attach garden hose.
2. Attach pressure hose.
3. Attach gun and lance.
4. Turn water supply ON.
5. Squeeze trigger to purge air from pump.
6. Insert nozzle.
7. Plug in power cord, reset the GFCI, start motor.
Gun kicks back. Hold with both hands.Risk of injection or injury to persons. Do
not direct discharge stream at persons.
Risk of fire and explosion. Do not spray
flammable liquids.
To reduce the risk of injury, read
owner's manual carefully before using.
2008 NT+E Co. 800-270-0810
SHUT-DOWN INSTRUCTIONS
1. Turn motor OFF.
2. Unplug the power cord.
3. Turn water supply OFF.
4. Squeeze trigger to relieve system pressure.
5. Remove garden hose.
6. Remove pressure hose.
Part No. 778069
WARNING
Call 1-800-270-0810 to order new labels.
Instruction Label: Part No. 778166 Warning Label: Part No. 778069
Page 7
Assembly Instructions
7
* Figures shown are for representation only. Actual components will vary by model.
Pressure Hose
Handle
Motor/Pump/Base Assembly
Lance
Spray Gun
Hardware Bag
I.) Unpack
Your pressure washer is shipped in one box. Separate and identify the components found in both boxes.
Page 8
8
Hose Hook – Qty 2
Part # 779761
Gun Hook – Qty 1
Part # 38509
Flange Nut – Qty 2
Part # 82019
Carriage Bolt - Qty 2
Part # 82233
T-Handle – Qty 2
Part # 38578
Grommet – Qty 5
Part # 35198
Nozzle – Qty 2
Part # varies
by model
Vented fill cap
(1573001 only)
Nylock Nut – Qty 4
Part # 777495
I.) Hardware Bag
Assembly Instructions
Page 9
Assembly Instructions
9
Nozzles
Grommets
Handle
T-handle knob
Flange nuts
Carriage Bolts
Hose Hook
Hook Detail
Flange nut
Hose Hook
Nylock nuts
III.) Handle Assembly
1.) Attach handle to base with two carriage bolts and t-handle knobs.
2.) Spin a flange nut backwards onto gun hook. (see hook detail)
3.) Mount the hose hooks onto the handle and gun hook onto the base as shown.
4.) Insert grommets into the holes on the handle nameplate.
5.) Press nozzles into grommets according to the colors indicated on the handle decal.
Page 10
Machine Component Identification
10
1.) Handle. Designed for easy cart
movement.
2.) Hose Hook. Store hose on hook.
3.) Pressure Hose. Attach quick couplers to
gun and water outlet.
4.) Chemical Hose. Submerge in cleaning
solution.
5.) Water Pump. Inspect for loose/broken
parts prior to each use.
6.) Motor. Leeson motor provides years of
reliable use.
7.) Gun Hook. Store gun on hook.
8.) Nozzles.
9.) Spray Gun. Always use two hands for
safe operation.
10.) Trigger. Actuate to allow pressurized
water to flow out of spray gun.
11.) Cord Hook. Store electrical cord on hook.
* Components shown are for representation only. Actual components will vary by model.
Page 11
Pump Component Identification
11
1573001
1573011 & 1573021
Page 12
Operation Instructions
12
Model
Time to fill a 5 gal. bucket
1573001
150 seconds
1573011
160 seconds
1573021
96 seconds
SHUT-DOWN INSTRUCTIONS
1. Turn motor OFF.
2. Unplug the power cord.
3. Turn water supply OFF.
4. Squeeze trigger to relieve system pressure.
5. Remove garden hose.
6. Remove pressure hose.
START-UP INSTRUCTIONS
1. Attach garden hose.
2. Attach pressure hose.
3. Attach gun and lance.
4. Turn water supply ON.
5. Squeeze trigger to purge air from pump.
6. Insert nozzle.
7. Plug in power cord
8. Reset the GFCI button on the cord
9. Start motor.
Skin puncture hazard.
High pressure fluid can inject under skin resulting in serious injury including amputation. Do not direct spray at people or animals.
-If skin injection happens, seek IMMEDIATE surgical treatment.
-Do not check for leaks with hand. Instead, use a piece of cardboard to check for leaks.
-Do not use unit if exterior hose damage is evident. Make sure all fittings are tight before starting. Relieve system pressure before servicing.
-Know how to stop engine and bleed pressures quickly. Be thoroughly familiar with the controls.
-Make sure accessories meet the unit's temperature and pressure limits.
-Stop engine and bleed pressures before leaving unit unattended.
WARNING
Water Supply
1.) Make sure the water supply is clean. Debris can cause excess pump wear and reduce performance.
2.) An insufficient water supply will damage your pump. Make sure the water supply is steady and is 20%
over the rated flow of your pump. Use a stopwatch to time how long it takes to fill a 5-gallon bucket with your garden hose. The bucket must fill faster than the times listed in the table below.
3.) The water supply garden hose must have an inside diameter of at least 5/8”. If the hose is more than 100 ft. long, the diameter must be at least 3/4”.
4.) Never use a reservoir tank as a water source. Drawing water out of a tank may cause pump cavitation and damage to your pump. This pressure washer is designed for a pressurized water source such as a city water faucet. However, the water source pressure must not exceed 115 psi (8 bar).
Always use a flexible rubber hose for your water supply. Do not use rigid piping.
Page 13
Operation Instructions
13
spray gun
spray gun safety lock
lance
spin-on coupler
Spray Gun Safety Lock
When not spraying, use the spray gun safety lock to prevent accidental high-pressure discharge.
* Note: Depending on model, gun may appear differently.
Attaching the Lance
Tighten spin-on coupler hand tight. Note: The o-rings make the seal so there is no need to tighten with a wrench.
Page 14
Operation Instructions
14
Flying objects.
Make sure nozzle is secure before squeezing trigger. If nozzle is not secure it will become a projectile. Serious injury can occur.
WARNING
CORRECT
INCORRECT
nozzle
collar
coupler
lance
collar completely pushed out.
collar NOT completely pushed out.
pump
hose
spray gun
Installing Nozzles
To install a nozzle pull back the collar and push the nozzle into the coupler. Once the connection is made, pull on the nozzle to make sure it is secure.
Attach Quick Connect Couplers
- To install the hose onto the pump, pull back the collar and push the hose into the coupler on the pump.
- To install the hose onto the spray gun, pull back the collar on the spray gun and push the hose into the coupler
on the spray gun.
Once the connections are made, pull on the hose to make sure it is secure.
Page 15
Operation Instructions
15
Risk of exposure to dangerous chemicals.
Serious injury or death can result if chemical manufacturer instructions are not
followed.
-Wear protective gloves when handling and cleaning with chemicals.
-Understand all safety hazards and first aid for all chemicals being used.
-When cleaning filters, check if chemicals have been used and take any
precautions that are recommended by the chemical manufacturer.
-Different chemicals may interact dangerously with each other, always follow
chemical manufacturer directions before switching chemicals.
-Calculate the correct amount of chemical to mix, dispose of excess chemical
per the manufacturer instructions.
-Never spray flammable liquids.
WARNING
strainer
diluted chemical
pump inlet
pump outlet
pump
Applying Chemicals
1.) Install the black nozzle when applying chemicals onto the cleaning surface.
2.) Start the pressure washer according to the start-up instructions.
3.) Submerge the chemical hose in cleaning solution. (See Pump Component Identification section for chemical
injector location.)
4.) Squeeze the spray gun trigger. The chemical injector will draw the chemical into the water stream.
5.) Apply chemicals evenly onto the cleaning surface. Allow the chemicals to react with the dirt, then clean at
high pressure with high pressure (green or yellow) nozzle.
6.) Never use more chemical than is necessary to clean the surface.
7.) To clean the chemical injector, draw water through the strainer until all the chemical is purged from the
system.
Page 16
Maintenance and Storage
16
What to Check
When To Check
What to Do
Inlet Filter
Each Use
Visually inspect and clean inlet filter with clear water.
Pressure Hose
Each Use
Visually inspect pressure hose and hose couplings. Replace hose if any of the following is evident: hose coupling is damaged, wire mesh is exposed or damaged, hose is permanently kinked or flattened, outer hose cover is blistered or loose.
Bolts
Each Use
Tighten any loose bolts.
Pump Oil
After 1st 50hrs,
then 3mo/500hr
Change pump oil. See pump oil change instructions on next page.
Maintenance Mode
Read and follow these safety rules whenever you will be servicing the pressure washer:
Turn off / unplug / relieve pressure first. Always turn off and unplug the pressure washer and
relieve system pressure before inspection or maintenance.
Replace guards. Make sure all guards and cover shields are replaced after servicing the pressure
washer.
Major repair. Major service, including the installation or replacement of parts, should be
performed only by a qualified electrical service technician. Obtain factory-approved parts from NorthStar Product Support at 1-800-270-0810.
Replacement parts. If a part needs replacement, only use factory approved repair parts.
Replacement parts that do not meet specifications may result in a safety hazard or poor operation of the pressure washer and will void the warranty.
Maintenance Schedule
Page 17
Maintenance and Storage
17
sight glass
drain plug
fill cap
Cat 3DNX25GSI Pump
fill cap
Comet BXD 1617E Pump
Oil capacity: 4.3oz. (.13L)
Oil capacity: 8.5 oz. (.25L)
FIG01854
Oil capacity: 8.5 oz. (.25L)
drain plug
sight glass
fill cap
Cat 2DX15ES Pump
drain plug
sight glass
Pump Oil Change
1.) Place a suitable container below the pump to catch the used oil, then remove the oil fill cap and oil drain
plug.
2.) Allow the used oil to drain completely, then reinstall the drain plug and tighten securely.
3.) Please dispose of used oil in a manner that is compatible with the environment. We suggest you take used
oil in a sealed container to your local recycling center or service station for reclamation. Do not throw it in the trash; pour it on the ground or down the drain.
4.) With the pump in a level position, fill to the halfway point on the oil sight glass (see pump oil capacities
below). For Comet pumps use Universal Tractor Transmission Oil or Mobil 1 15W50 synthetic oil. For Cat pumps use SAE30 non-detergent oil or Cat Pump Oil Item# 22158.
Page 18
Maintenance and Storage
18
RV Antifreeze
Funnel
Hose
Water Inlet
Winter Storage
Protect your pump, hose and gun from freezing. Items needed: 12” piece of garden hose or equivalent, funnel and RV antifreeze (approximately 6 oz.)
1.) Follow the storage instructions listed above.
2.) Make sure the motor start switch is OFF.
3.) Attach the garden hose with funnel to the pump inlet (see illustration).
4.) Pour RV antifreeze into the funnel, run motor until antifreeze comes out the pump outlet.
5.) Drain all water from the high pressure hose. Depress trigger on gun and drain all water out of gun/lance.
Page 19

Troubleshooting

19
Problem
Solution
Motor will not start
SOLUTION: A,B
Low/Surging pressure or no water flow
SOLUTION: C,D,E,F,G,H
No chemical injection
SOLUTION: I,J,K,L
Cause
Solution
A- Tripped GFCI cord
Reset GFCI cord
B- Tripped motor relay
Reset motor
C- Insufficient water supply
See water supply section of this manual
D- Plugged pump inlet filter
See maintenance section of this manual
E- Wrong nozzle
Make sure high pressure nozzle is being used
F- Plugged nozzle
Remove nozzle, check for blockage
G- Worn nozzle
Replace nozzle
H- Leak in pressure hose
Replace pressure hose
I- Wrong nozzle
Make sure chemical nozzle is being used
J- Back pressure from extra long discharge hose
Try shorter hose
K- Leak in chemical siphon hose
Replace hose – use hose clamps if necessary
L- Chemical strainer not submerged
Make sure strainer is completely submerged
The manufacturer reserves the right to make improvements in design and/or
changes in specifications at any time without incurring any obligation to install
them on units previously sold.
Any Questions, Comments, Problems or Parts Orders
Call NorthStar Product Support 1-800-270-0810
Page 20
Specifications
20
1573001
1573011
PSI (bar)
1700 (117)
PSI (bar)
2000 (138)
GPM (l/min)
1.5 (5.7)
GPM (l/min)
1.5 (5.7)
Max Water Temp
140F (60C)
Max Water Temp
140F (60C)
Dimensions L x W x H
34” x 21” x 38”
(864mm x 534mm x 965mm)
Dimensions L x W x H
34” x 21” x 38”
(864mm x 534mm x 965mm)
Weight
95 lb (44kg)
Weight
115 lb (44kg)
1573021
PSI (bar)
2750 (190)
GPM (l/min)
2.5 (9.4)
Max Water Temp
140F (60C)
Dimensions L x W x H
34” x 21” x 38”
(864mm x 534mm x 965mm)
Weight
139 lb (55kg)
Wiring Diagram
Page 21
Wiring Diagram
21
Page 22
Parts Explosion M1573001 Rev – G.1
22
Page 23
Parts Explosion M1573001 Rev – G.1
23
ITEM #
PART #
DESCRIPTION
QTY
MODELS
1
38509
Threaded Gun Hook
1
All
2
779826
NorthStar Decal
1
All
3
35198
7/16 ID Grommet
5
All
4
780223
Handle 1 All
5
779761
Hose/Cord Hook
2
All
6
38578
T-Handle Knob
2
All
7
779924
Base
1
All
8
788813
Tire Wheel Assembly
2
All
9
305200
Wheel Retainer
2
All
10
38524
5/16 x 25' Gray Hose
1
1573011,1573021
11
777915
3/8" Quick Connect Nipple
1
1573011,1573021
12
777914
3/8" Quick Connect Coupler
1
1573011,1573021
13
2212
Chemical Strainer
1
All
14
777165
1/4" Braided Chemical Hose
3 ft
All
15 778146
Motor Cord, 14-2 AWG SJTW
1
1573001
778147
Motor Cord, 12-2 AWG SJTW
1
1573011,1573021
16
780841
1/4 x 25' Black Hose
1
1573001
17
779166
18.5" Lance 1 All
18
777904
1/4" Quick Connect
1
All
19 778150
Nozzle 2 pack #2.0
1
1573001,1573011
38530
Nozzle 2 pack #3.0
1
1573021
20
2215
Bumpers 2 All
23
779564
Electric Control Box Cover
1
All
24 778140
GFCI Cord, 120V/15A
1
1573001
778141
GFCI Cord 120V/ 20A
1
1573011
778142
GFCI Cord, 240V/30A
1
1573021
25 777616
Motor, 1.5 HP Leeson
1
1573001
777617
Motor, 2.0 HP Leeson
1
1573011
778670
Motor, 5.0 HP Leeson
1
1573021
26 786056
Pump, Comet BXD 1617E
1
1573001
778154
Pump, Cat 2DX
1
1573011
789205
Pump, Cat 4DNX
1
1573021
29
777915
QC 3/8" Female Nipple
1
1573011,1573021
30
35918
Thermal Protector
1
1573011,1573021
31
38596
Inlet Filter
1
1573011,1573021
35 777855
Toggle Switch
1
All
5260
On-Off Plate 1 All
36
38527
Gun, Consumer, QC
1
1573011,1573021
37
313107
3/8" Male NPT Coupler
1
1573011,1573021
38
38526
Gun, 2700 PSI, 22mm
1
1573001
39
778070
Cord Warning
1
All
40 778151
DP Contactor 120V/25A
1
1573011
778152
DP Contactor 230V/30A
1
1573021
Page 24
Pump Exploded Views – Rev G.1
24
Part # 786056 Comet BXD 1617E
Page 25
25
Page 26
26
Part # 778154 Cat 2DX
Page 27
27
Ref#
P/N
DESCRIPTION
QTY
Ref#
P/N
DESCRIPTION
QTY
5
Not Available
Screw 3 106
Kit #1
Seal 3 8
CA547153
Bearing Cover
1
120
Not Available
Seal Case
3
10
CA14041
O-Ring, Bearing Cover
1
121
CA13976
O-Ring for Seal Case
3
11
CA55337
Oil Seal
1
125
Kit #1
Seal
3
15
CA14488
Inner Ball Bearing
1
160
CA17428
O-Ring, Inlet
3
20
CA547048
Connecting Rod
3
161
CA547077
Seat, Inlet
3
24
Not Available
Oil Plug Cap
1
162
CA48361
Back-up Ring
3
25
CA549446
Crankshaft
1
163
CA43358
O-Ring
3
27
CA56084
Ball Bearing
1
164
CA547076
Seat, Discharge
3
32
CA547961
Cap 1 166
CA547098
Valve
6
33
CA14179
O-ring for Oil Filter Cap
1
167
CA46865
Spring 6 37
CA92241
Gauge, Bubble Oil w/Gasket
1
168
CA543988
Retainer, Spring, Inlet
3
38
CA44428
Gasket, Flat Flex Oil Gauge
1
169
Kit #2
Retainer, Spring, Discharge
3
48
CA44842
Drain Plug
1
172
CA142807
O-Ring for Plug
3
49
CA14179
O-Ring for Drain Plug
1
174
CA547104
Plug, Valve w/o-ring
3
53
Not Available
Crankcase
1
185
Not Available
Head, Manifold w/Unloader Body
1
64
CA46229
Crosshead Pin
3
188
Not Available
Screw 6 65
CA542402
Plunger Rod
3
197
CA941516
Inlet Fitting Assembly
1
70
CA47215
Oil Seal
3
249
CA30520
Adapter Mount Assembly
1
90
CA547091
Plunger
3
255
CA30516
Bolt Mount Assembly
1
98
CA46730
Washer
3
469
CA7332
Chemical Fixed Injector
1
99
CA542405
Retainer, Plunger
3
KITS
100
CA46233
Retainer, Seal
3 Kit#1
CA76975
Seal Kit: Inclds: 98, 106, 121, 125
1
*One Kit will Complete One Pump*
Kit#2
CA76976
Valve Kit: Inclds: 160, 161, 162, 163, 164, 166, 167, 168, 169, 172
1
Part # 789205
Cat 4DNX
Page 28
28
This page has intentionally been left blank.
Page 29
Limited Warranty
29
Item #
Warranty Period
1573001
1 year from date of purchase by user
1573011, 1573021
2 years from date of purchase by user
Dear Valued Customer:
The NorthStar Product you just purchased is built with the finest material and craftsmanship. Use this product properly
and enjoy the benefits from its high performance. By purchasing a NorthStar product, you show a desire for quality and durability. Like all mechanical equipment this unit requires a due amount of care. Treat this unit like the high quality piece of machinery it is. Neglect and improper handling may impair its performance. Please thoroughly read the instructions and understand the operation before using your product.
Limited Warranty
NorthStar shall warranty any piece of equipment manufactured, or parts of equipment manufactured, to be free from defects in material or workmanship for a period of:
NorthStar shall warranty any wear item, including, but not limited to, valves, seals, pump diaphragms, hoses, and filter elements to be free from defects in material or workmanship for a period of 90 days from the date of purchase by user. This warranty applies to the original purchaser of the equipment and is non transferable. Verification of purchase is the responsibility of the buyer. Parts will be replaced or repaired at no charge, except when the equipment has failed due to lack of proper maintenance. Any misuse, abuse, alteration or improper installation or operations will void warranty. Determining whether a part is to be replaced or repaired is the sole decision of NorthStar.
NOTE: Some services performed by parties other than NorthStar may void warranty.
This warranty covers parts only. It will not provide for replacement of complete products due to defective parts. Components not manufactured by NorthStar are guaranteed by their manufacturer and can be serviced at factory-authorized locations near you. Any costs incurred due to replacement or repair of items outside of a NorthStar approved facility is the responsibility of the buyer and not covered under warranty. NorthStar can supply you with the service center location in your area.
This warranty specifically excludes the following; failure of parts due to damage caused by accident, fire, flood, windstorm, acts of God, applications not approved by NorthStar in writing, corrosion caused by chemicals, use of replacement parts which do not
conform to manufacturer’s specifications, and damage caused by vandalism. Additional exclusions: loss of running time,
inconvenience, loss of income, or loss of use, including any implied warranty of merchantability of fitness for a specific use.
Warranty does not cover items subject to normal wear such as tires, receptacles or any part subject to direct physical contact by the public. This warranty does not cover any personal injury or damage to surrounding property caused by failure of any part.
This warranty is in lieu of any other warranty expressed or implied and NorthStar assumes no other responsibility or liability outside that expressed within this warranty.
Please fill in the following information and have it on hand when you call in on a warranty claim.
Customer Number: ______________________________________________________________
Date of Purchase: _______________________________________________________________
NorthStar Serial Number: _______________________________________________________
Item Number: __________________________________________________________________
Page 30
30
®
Manufactured by
Northern Tool + Equipment Co.,
2800 SouthCross Drive West
P.O. Box 1499 Burnsville, MN 55337-0499
Loading...