NorthStar 190 BATH/SPA TV, 154 Installation Instructions Manual

NORTHSTAR™

190 BATH/SPA TV

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

Must be installed by a qualified electrician
Read these instructions. Keep these instructions for future use.
Install in accordance with manufacturer’s instructions.

This product is suitable for wet locations. Clean only with water, mild soap and soft cloth. Do not clean with harsh
detergents.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(Including amplifiers) that produce heat.

Do not defeat the safety purpose of the grounding-type plug.
A grounding-type plug has two blades and a third grounding prong.
The third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
where they exit from the appliance.

Only use attachments/accessories specified by the manufacturer.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as: power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.

Terminals that are marked with a lightning flash are hazardous. Any external wiring connections to these terminals
requires installation by an electrician.

CAUTION

READ ALL INSTRUCTIONS PRIOR TO INSTALLATION

WARNING:

TO PREVENT INJURY, THE BATH/SPA TV MUST BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER’S
INSTRUCTIONS

CAUTION: NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. BEWARE
OF STATIC SENSITIVE PARTS.

UNPACKING YOUR BATH/SPA TV

Verify Contents

Prior to installation unpack items and verify contents. The Bath/Spa TV comes with the following components:

1. In-Wall box with right angled plastic L-channel pieces

2. A NRTL Approved Power Supply, 15 Watts AC/DC, 90-264 Volts input and 12 Volts output

3. Power cord

4. HDMI cable

5. RF Cable

6. LCD-TV with glass face and stainless steel bezel

7. Remote Control

2 THERE’S ONLY ONE™ ELECTRIC MIRROR® | E [e-mail] | T [phone] | F [phone] | W www.electricmirror.com

INSTALLATION

Please note that all electrical installations should be carried out by a fully qualified electrician in conformance with
the National Electrical Code.

Cut a 20-7/8” x 13-1/2” x 3-1/2” deep recess in the wall board to accommodate the In-Wall Box. The recess in the
wall should be open below the In-Wall Box to allow cables to enter the bottom of the unit. The wall should be of
suitable strength to support the weight of the Bath/Spa TV (32.5 lbs). Vertically mounted 2” x 4” wall studs may
be used to provide extra support to the wall board.

CABLING AND ELECTRICAL INSTALLATION

Please note, all electrical installation should be carried out by a fully qualified electrician in conformance with the
National Electrical Code.

Electrical Outlets

The LCD-TV requires a GFCI receptacle in which to plug the 12-120V AC/DC adapter. Install a receptacle for this
adapter. The receptacle should be located in a readily accessible area in a dry location.
FAILURE TO DO SO MAY RESULT IN DEATH OR SERIOUS INJURY

Plug the power supply cable of the AC/DC adapter into the outlet. The power adapter is not waterproof and
therefore must be positioned in a dry, well-ventilated, accessible area away from water, moisture or heat source.
The 12V side of the AC/DC adapter powers the Northstar LCD-TV. The AC/DC adapter to the LCD-TV is fitted
with a 25’ low voltage cable that should be fed behind the wall to the LCD-TV. Make sure there are two (2) feet of
extra slack at the LCD-TV to allow the power connector to be plugged into the TV for installation. The low voltage
cable should not be cut, shortened or lengthened in any way. Doing so may cause damage to the unit and voids
all warranty.

THERE’S ONLY ONE™ ELECTRIC MIRROR® | E [e-mail] | T [phone] | F [phone] | W www.electricmirror.com

3

Audio Connection

The Bath/Spa TV will use a ceiling speaker (see speaker specification for installation). Place speaker cable behind
wall running from the Bath/Spa TV to the ceiling speaker.

Video Connection

The Northstar LCD-TV has the following video input options:
RF Connection
Composite Connections
S-Video Connection
VGA Connection
HDMI Connection

INSTALLING THE MOUNTING BRACKET

Level and attach the In-Wall Box into the wall using the twelve (12) screws provided.

INSTALLING THE LCD-TV

Remove the Northstar 190 LCD-TV from its packaging. The back of the TV has a cable outlet module with cables
configured to the customer’s requirements. In the proper orientation the cables exit downward out of the module.
Make sure the appropriate cables and their connectors are present. These cables include a low-voltage power
cord and audio/video source connectors.

Fit the Northstar 190 LCD-TV into the In-Wall Box by aligning the unit on the plastic L-Channel pieces. Push the
TV towards the back of the In-Wall Box until the magnetic force is apparent. Be careful with your hand placement
to avoid having your fingers in between the stainless steel bezel and the wall when the magnetic force takes full
eect.

4 THERE’S ONLY ONE™ ELECTRIC MIRROR® | E [e-mail] | T [phone] | F [phone] | W www.electricmirror.com