Nortel Networks 222 User Manual

Steps 1 4

Before you start

Steps 18 19

Test your Internet connection

Steps 13 16

Start the wizard

Steps 10 12

Access the BSR222

Steps 5 8

Install the hardware

Step 9

Assign TCP/IP addresses

Step 17

Enter ISP IP addresses (if required)

BSR222

Business Secure Router 222 Quick Install Guide

You can download all the documents referred to in this Quick Install guide at www.nortel.com.

1. Contact your Internet Service

Provider (ISP) to get the following information:

a. Encapsulation type: Ethernet, PPP

over Ethernet, PPTP

b. ISP IP addresses: WAN, DNS

servers, Gateway, and WAN MAC address

2. Get your Domain Name from the

User Accounts dialog box in the Control Panel. For details, see your operating system Help files.

3. Get your Computer Name from the System

Properties dialog box on your computer.

4. Get the IP addresses

of DNS and remote servers on your LAN. (optional)

5. Place the BSR222 on

a flat surface with sufficient clearance for the front and rear connection points, or use the supplied holder to vertically mount it.

6. Connect your PC

and up to three other computers or network devices to the four Ethernet ports.

7. Connect your Internet service to the

WAN port next to the Power LED.

8. Connect the supplied power adapter to the rear of the

BSR222 and to a grounded AC power source.

9. Set up the IP addresses on each computer connected to the

BSR222:

a. Set each computer to dynamically obtain an IP address, or

assign a static IP address. If you assign a static IP address, choose one between 192.168.1.2 and 192.168.1.254.

Note: Assign a static IP address for PPTP encapsulation.

b. Assign a subnet mask of 255.255.255.0 and a default

gateway of 192.168.1.1.

c. If you assign a static IP address in step 9a, assign the DNS

server IP addresses. If you do not know the DNS server IP addresses, choose Obtain a DNS server address automatically.

10. In the address

field of your browser, enter 192.168.1.1

11. Enter the default user

name (nnadmin) and password (PlsChgMe!) to log onto the BSR222.

12. You can replace the default password or

use it as it is.

13. On the left

navigation pane, click

Wizard.

16. Depending on the type of encapsulation that your ISP

uses, enter the following information:

Ethernet

Choose the Service Type: Standard, RR-Toshiba, RR-Manager, or RR-Telstra. Enter User Name, Password, and Login Server IP Address if required.

PPP over Ethernet

Enter the Service Name, User Name and Password assigned by your ISP, and enter 100 seconds as the Idle Timeout. Choose Nailed-Up Connection to maintain constant service.

PPTP

Enter the User Name and Password assigned by your ISP. Choose Nailed-Up Connection to maintain constant service. Also, enter the My IP address, My IP subnet mask, PPTP server IP address, and Connection ID (of the form

n:name).

17. If your ISP provides a

fixed IP address for their WAN:

a. Choose Use fixed IP

address.

b. Enter the My WAN IP,

My WAN IP subnet mask, Gateway (Remote IP), and System DNS Servers addresses, if required.

Otherwise, accept the default value of Get

automatically from ISP.

18. The BSR222 setup is

complete. Close your browser.

19. Test your connection to the Internet by opening your

browser and visiting a known Web site.

15. From the first Wizard window, choose the type of

encapsulation and service that your ISP supplies. The wizard displays different windows for each type of encapsulation and service.

14. In the General Setup window, enter the system

name (your computer name) and the domain name.

For more detailed installation instructions, refer to Nortel Business Secure Router 222 Fundamentals.

N0118060

BSRQuickInstallGuide_Trifold3.pdPage 1 8/2/2006 10:01:54 AM

CMY