Noritz America NR83OD Installation Manual
NORITZ AMERICA
*SBB80YR*
CERTIFIED
R
Installation Manual
CORPORATION
TANKLESS GAS WATER HEATER
NR83OD (GQ-2457WS US)
Potential dangers from accidents during installation and use are divided into the following three
categories. Closely observe these warnings, they are critical to your safety.
DANGER
WARNING
CAUTION
WARNING:
causing property damage, personal injury or death.
Prohibited
If the information in this manual is not followed exactly, a re or explosion may result
DANGER indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
Disconnect
Power
(Outdoor Installation)
Ground
Be sure to do
CAUTION
Requests to Installers
• In order to use the water heater safely, read this installation manual carefully, and follow the
installation instructions.
• Failures and damage caused by erroneous work or work not as instructed in this manual are not
covered by the warranty.
• Check that the installation was done properly in accordance with this Installation Manual upon
completion.
•
After completing installation, please either place this Installation Manual in a plastic pouch and
attach it to the side of the water heater (or the inside of the pipe cover or recess box if applicable),
or hand it to the customer to retain for future reference. Also, be sure to ll in all of the required
items on the warranty and to hand the warranty to the customer along with the Owner's Guide.
FOR USE IN RESIDENTIAL OR MANUFACTURED HOME APPLICATIONS.
Installation must conform with local codes, or in the absence of
local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54-
latest edition and/or the Natural Gas and Propane Installation
Code CSA B149.1 - latest edition.
Low NOx
Approved by
SCAQMD
14 ng/J or 20 ppm
(Natural Gas Only)
When applicable, installation must conform with the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part
3280 or the Canadian Standard CAN/CSA-Z240 MH Mobile
Homes, Series M86.
Noritz America reserves the right to discontinue, or change at any
time, the designs and/or specications of its products without notice.
SBB80YR
Rev. 08/17
1.
The following accessories are included with the unit.
Included Accessories
Check for any missing items before starting installation.
Part Shape
Cross Recessed
Head Screw
Remote Controller
(See p. 20)
2.
Remote Controller
Optional Accessories
Cord (26ft (8m))
Isolation Valves*
(includes pressure
relief valve)
Q’ty
3
1
Q’ty
1
1
each
ShapePart
Owner's Guide, Warranty,
Installation Manual
(this document)
Remote Controller
Cord (6ft (2m))
The accessories listed below are not
included with the units, but may be necessary
for installation.
ShapePartPart Shape
Quick Connect Cord
(QC-2)
Remote Controller
Outdoor
Junction Box
Q’ty
1
each
1
Q’ty
1
1
Pipe Cover
(PC-2S)
Recess Box
(RB-700-1)
* Isolation valves are necessary for ushing the Heat Exchanger.
They allow for easy ushing of the system.
1
Noritz Connect
Wireless Adapter
NWC-ADAPTER
(NAW-1 US)
1
1
2
Distance at center: 15.8 - 31.8 in. (401 - 808mm)
Make this distance as short
as possible.
*
will become unstable as the
pipe length increases.
G
Quick Connect
Cord
Remote Controller Cord
Gas Supply Piping
Cold Water Supply
Hot Water
Remote Controller
Terminal Block
Cord
Connector
Cord
Connector
3.
Quick Connect Multi System Installation
• The Quick Connect Multi System allows the installation of two units together utilizing only the Quick
Connect Cord.
The Quick Connect Cord is 6 ft.(2m) long. Install the units 2-18" (50 - 457mm) apart from each
other to ensure the cord will be able to reach between the units. (See Typical Plumbing diagram).
(If the distance between the two units is too great, not only will the cord not be able to reach,
but the water temperature may also become unstable because of the difference in pipe length
between the two units).
System Diagram
Typical Plumbing
Distance on sides
2 - 18 in. (50 - 457mm)
* When connecting two units, use only a
single remote controller.
Note: Connect the remote
controller to only one
of the units.
The hot water temperature
• Insulate the hot water piping to prevent heat loss. Insulate and apply heating materials to the
cold water supply piping to prevent heat loss and freezing of pipes when exposed to excessively
cold temperatures.
Union
Quick Connect
cord
Pressure
Relief
Valve
Shutoff
Valve
Leave enough clearance around the plumbing to
apply insulation. It will be necessary to add
bends to the piping to ensure that this clearance
is available.
Union
Gas Valve
Union
Shutoff Valve
Size the piping to allow for the
maximum flow rates of the units.
Hot Water
Cold Water
Shutoff Valve
The backflow preventer is
put up before it diverges.
3
Before Installation
Indoor
4.
WARNING
Check the Gas
• Check that the rating plate indicates the correct type of gas.
• Check that the gas supply line is sized for
180,000 Btuh.
Check the Power
• The power supply required is 120VAC, at 60Hz.
May result in re or electric shock.
Use Extreme Caution if Using With a Solar Pre-Heater
• Using this unit with a solar pre-heater can lead to unpredictable output temperatures and
possibly scalding. If absolutely necessary, use mixing valves to ensure output temperatures do
not get to scalding levels. Do not use a solar pre-heater with the quick-connect multi-system.
Precautions for Mobile Home Installation
• Verify that the gas supply type matches the gas type listed on the rating plate. If a gas conversion
must be done, follow the instructions listed in the gas conversion kit manual.
CAUTION
Do Not Use Equipment for Purposes Other Than Those Specied
• Do not use for other than increasing the temperature of the water supply, as unexpected accidents
may occur as a result.
Check Water Supply Quality
• If the water supply is in excess of 12 grains per gallon (200 mg/L) of hardness, acidic or otherwise
impure, treat the water with approved methods in order to ensure full warranty coverage.
Choosing Installation Site
5.
* Locate the appliance in an area where leakage from the unit or connections will not result in damage
to the area adjacent to the appliance or to the lower oors of the structure. When such installation
locations cannot be avoided, a suitable drain pan, adequately drained, must be installed under the
appliance. The pan must not restrict combustion air ow.
* As with any water heating appliance, the potential for leakage at some time in the life of the product
does exist. The manufacturer will not be responsible for any water damage that may occur.
DANGER
• This water heater is for outdoor installation only.
Never install it indoors.
Do not enclose the termination with corrugated
metal or other materials.
4
This will cause carbon monoxide
poisoning and a potential re
hazard.
WARNING
• Avoid places where res are common, such as those where gasoline,
benzene and adhesives are handled, or places in which corrosive gases
(ammonia, chlorine, sulfur, ethylene compounds, acids) are present.
Using the incorrect voltage may result in re or cracking.
• Avoid installation in places where dust or debris will accumulate.
Dust may accumulate and reduce the performance of the unit's fan.
This can result in incomplete combustion.
• Avoid installation in places where special chemical agents
(e.g., hair spray or spray detergent) are used.
Ignition failures and malfunction may occur as a result.
• Carbon Monoxide Poisoning Hazard. Do not install this water heater in a
recreational vehicle or on a boat.
CAUTION
• Install the water heater in a location where it is free from obstacles and
stagnant air.
• Consult with the customer concerning the location of installation.
• Do not install the water heater near staircases or emergency exits.
Prohibited
• Do not install the water heater where the exhaust will blow on outer walls
or material not resistant to heat. Also consider the surrounding trees and
animals.
The heat and moisture from the water heater may cause discoloration of
walls and resinous materials, or corrosion of aluminum materials.
• Do not locate the vent termination directed towards a window or any
other structure which has glass or wired glass facing the termination.
• Install in a location where the exhaust gas ow will not be affected by
fans or range hoods.
• Take care that noise and exhaust gas will not affect neighbors.
Avoid installation on common walls as the unit will make some
operational noises while it is running.
• Avoid installation where the unit will be exposed to excessive winds.
• Before installing, make sure that the vent termination will have the proper
clearances according to the National Fuel Gas Code (ANSI Z223.1-latest
edition ) or the Natural Gas and Propane Installation Code (CSA B149.1).
State of California: The water heater must be braced, anchored or strapped to avoid moving during
an earthquake. Contact local utilities for code requirements in your area or call: 1-866-766-7489 and
request instructions.
The Commonwealth of Massachusetts:
1) This water heater can only be used in outdoor applications if the usage is restricted to summertime
usage exclusively.
2) The water heater can be used for hot water only and not in a combination of domestic and space
heating.
Prohibited
5
Installation Clearances
6.
WARNING
Before installing, check for the following:
Install in accordance with relevant building and mechanical codes, as well as any local, state or
national regulations, or in the absence of local and state codes, to the National Fuel Gas Code
ANSI Z223.1/NFPA 54 – latest edition. In Canada, see the Natural Gas and Propane Installation
Code CSA B149.1 - latest edition for detailed requirements.
Item Check
• Maintain the following clearance from both combustible
and non-combustible materials.
Required Clearances From Heater
• When installing the unit in a common side corridor, provide
a clearance of 47" (1,190mm) or more in front of the unit.
• Set the bottom edge of the exhaust port about
84" (2,130mm) from the corridor oor.
Handrail
Illustration
24" (600mm)
or more
36" (900mm)
or more
6" (150mm)
or more
47" (1,190mm) or more
about 84"
(2,130mm)
common side
corridor
6
• When installing the unit on a balcony, etc., secure an
evacuation route of 24" (600mm) or more in width.
• Provide clearance of 24" (600mm) or more in front of
the unit to facilitate inspection and repair. Do install the
unit in a location where the unit is out of reach, such as
Surrounding the area of installation
the wall of the second oor.
24" (600mm)
or more
Handrail
balcony, etc.
Clearance Requirements from Vent Terminations to Building Openings
DescriptionRef
A=
Clearance above grade, veranda, porch,
deck, or balcony
B=
Clearance to window or door that may
be opened
C=
Clearance to permanently closed window
D=
Vertical clearance to ventilated soffit located
above the terminal within a horizontal distance
of 2 feet (61 cm) from the center line of the terminal
*
E=
Clearance to unventilated soffit
*
F=
Clearance to outside corner
*
G=
Clearance to inside corner
*
H=
Clearance to each side of center line
extended above meter/regulator assembly
I=
Clearance to service regulator vent outlet
J=
Clearance to nonmechanical air supply
inlet to building or the combustion air inlet
to any other appliance
K=
Clearance to a mechanical air supply inlet
6 ft (1.83 m)
L=
Clearance above paved sidewalk or paved
driveway located on public property
Clearance under veranda, porch, deck,
or balcony
7 ft (2.13 m)†
M=
1
In accordance with the current CSA B149.1 Natural Gas and Propane Installation Code
2
In accordance with the current ANSI Z223.1 / NFPA 54 National Fuel Gas Code
† A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single
family dwellings and serves both dwellings.
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
* Clearance in accordance with local installation codes and the requirements of the gas supplier.
Clearance to opposite wall is 24 inches (60 cm).
12 in (30 cm)‡
*
12 in (30 cm)
6 in (15 cm) for appliances
≤ 10,000 Btuh (3kW), 12 in
(30 cm) for appliances > 10,000
Btuh (3kW) and ≤ 100,000 Btuh
(30 kW), 36 in (91 cm) for
appliances > 100,000 Btuh (30 kW)
Above a regulator within 3 ft (91 cm)
horizontally of the vertical center line of
the regulator vent outlet to a maximum
vertical distance of 15 ft (4.5 m)
4 ft (1.2 m) below or to side
of opening; 1 ft (300 mm)
above opening
6 in (15 cm) for appliances
≤ 10,000 Btuh (3kW), 12 in
(30 cm) for appliances > 10,000
Btuh (3kW) and ≤ 100,000 Btuh
(30 kW), 36 in (91 cm) for
appliances > 100,000 Btuh (30 kW)
4 ft (1.2 m) below or to side
of opening; 1 ft (300 mm)
above opening
*
*
*
*
**
*
*
*
3 ft (91 cm) above if within
10 ft (3 m) horizontally
*
12 in (30 cm)
US Non-Direct Vent Installation
2
Canadian Non-Direct Vent Installation
1
Vent Terminal
Air Supply Inlet
Area Where Terminal
is Not Permitted
* All clearance requirements are in accordance with ANSI Z21.10.3 and the National Fuel Gas Code,
ANSI Z223.1 and in Canada, in accordance with the Natural Gas and Propane Installation Code
CSA B149.1.
7
Installation
* Do not change any other dipswitches.
ON= OFF=
7.
Securing to the wall
• The weight of the device will be applied to the wall. If the strength of the wall is not
sufcient, reinforcement must be done to prevent the transfer of vibration.
• Do not drop or apply unnecessary force to the device when installing. Internal parts may
Be sure to do
be damaged and may become highly dangerous.
• Install the unit on a vertical wall and ensure that it is level.
Item
Check
CAUTION
• When installing with bare hands, take caution to
not inict injury.
• Be careful not to hit electrical wiring, gas, or water
piping while drilling holes.
1. Drill a single screw hole, making sure to hit a stud.
2. Insert and tighten the screw and hang the unit by
the upper wall mounting bracket.
Locating Screw Holes
3. Determine the positions for the remaining four screws
(two for the top bracket and two for the bottom), and
remove the unit.
4. Drill holes for the remaining four screws.
5. Hang the unit again by the rst screw, and then
insert and tighten the remaining four screws.
6. Take waterproong measures so that water does
not enter the building from screws mounting the
Mounting
device.
Illustration
Location of Screw Hole
Mounting Bracket
(upper)
Locating Screw Holes
Anchoring Screw
• Make sure the unit is installed securely so that it will
not fall or move due to vibrations or earthquakes.
Structure
• Adjust the dip switches as illustrated in the table to
the right if this water heater is installed at an altitude
of 2000 ft. (610m) or higher.
• Disconnect power to the water heater before
changing the dip switches. Failure to perform this
step will result in a "73" code displayed on the remote
controller and a cease in operation. If this occurs,
disconnect, then reconnect power to the water heater
Above 2,000 ft.
to reset the system.
Note : Please refer to page 20 for the location of the
Installations at Elevations
dip switch bank.
8
* High elevation adjustment.
65
0 - 2,000 ft (0 - 610m)
2,001 - 4,000 ft (611 - 1,220m)
4,001 - 6,000 ft (1,221 - 1,830m)
6,001 - 8,000 ft (1,831 - 2,440m)
8.
Gas Piping
Follow the instructions from the gas supplier.
CAUTION
The guidelines and examples we have provided in this manual section are for reference only.
The sizing and installation of the gas system for this water heater, as with any gas appliance, is the sole respon
of the installer. The installer must be professionally trained to do such work and must always follow all local
and national codes and regulations. Gas line sizing calculations must be performed for every installation.
Please contact Noritz America at 866-766-7489 if you have any questions or concerns.
Gas Type
The gas type indicated on the water heater rating plate (NG or LP) must match the type of gas being supplied to the water heater.
Gas Conversions
If the gas type supplied does not match the gas type on the rating plate, obtain a replacement unit with the proper gas type.
If a gas type conversion must be made, there are conversion kits available for some models. [The conversion kit shall be
installed by a qualied service agency in accordance with the manufacturer’s instructions and all applicable codes and
requirements of the authority having jurisdiction. The qualied service agency is responsible for the proper installation of
this kit. Improper installation of this kit will void the warranty.]
Meter
The gas meter must be sized properly for the water heater and other gas appliances to operate properly.
Select a gas meter capable of supplying the entire btuh demand of all gas appliances in the building.
sibility
Regulators
Ensure that all gas regulators used are operating properly and providing gas pressures within the specied range of the
water heater being installed. Excess gas inlet pressure may cause serious accidents.
CAUTION
WARNING
Pressure
Check the gas supply pressure immediately upstream at a location provided by the gas company.
pressure must be within the limits shown in the specications section with all gas appliances
pressure must be within the range specied. This is for the purposes of input
cause a loss of ame or ignition failure at other appliances in the home, which may result in unburned gas in the home.
Serious accidents such as re or explosion may result.
Measuring Gas Pressure
In order to check the gas supply pressure to the unit, a tap is provided on the gas inlet.
Remove the 9/32” hex head/Philips screw from the tap, and connect a manometer
using a silicon tube. Open up at least 2 xtures and hold in the maximum manifold
pressure button on the circuit board. Please call Noritz for details.
adjustment. Low gas pressure may
operating. The inlet gas
Supplied gas
WARNING
Pressure Test
The appliance and its gas connections must be leak tested before placing the appliance in operation. The appliance
must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any
pressure
not recommend pressure testing in excess of ½ psig (3.5kPa). If it must be done, the appliance and its individual
shutoff valve must be completely disconnected from the gas supply piping system during the test process.
Pipe Sizing/Flexible Connectors
A gas shutoff valve must be installed on the supply line. Gas ex lines are not recommended unless the minimum
inside diameter is ¾” or greater and the rated capacity of the connector is equal to or greater than the BTU
capacity of the water heater. Gas piping shall be in accordance with local utility company requirements and/
or in the absence of local codes, use the latest edition of National Fuel Gas Code (NFPA54GC), ANSI
Z223.1. In Canada, use the latest edition of CSA B149.1, National Gas and Propane installation code.
Size the gas line according to total btuh demand of the building and length from the meter or regulator so
that the following supply pressures are available even at maximum demand.
testing of the gas supply piping system at test pressures equal to or less than ½ psig (3.5 kPa). We do
Natural Gas Supply Pressure
Min 4” WC
Max 10.5” WC
LP Gas Supply Pressure
Min 8” WC
Max 14” WC
9
Loading...