Norgren R07 Installation Instructions
DISASSEMBLY
1. Regulator can be disassembled without removal from air
line.
2. Shut off inlet pressure. Reduce pressure in inlet and outlet
lines to zero.
3. Turn adjustment (2 or 5A) fully counterclockwise to remove
all force on regulating spring (6).
4. Disassemble in general accordance with the item numbers
on exploded view.
CLEANING
1. Clean parts with warm water and soap.
2. Rinse and dry parts. Blow out internal passages in body
with clean, dry compressed air.
3. Inspect parts. Replace those found to be damaged.
ASSEMBLY
1. Lubricate seals and o-rings with o-ring grease.
2. Assemble the unit as shown on the exploded view.
3. Torque Table
TORQUE
ITEM NM (INCH-POUNDS)
2, 5A (Bonnet) 7,34 to 8,47 (65 to 75)
9 (Early valve seat) 0,45 to 0,68 (4 to 6)†
11 (Current valve seat) 0,34 to 0,56 (3 to 5)†
† Diaphragm pin (8) must slide freely thru valve seat after
torquing.
WARNING
These products are intended for use in industrial
compressed air systems only. Do not use these products
where pressures and temperatures can exceed those listed
under Technical Data.
If outlet pressure in excess of the regulator pressure
setting could cause downstream equipment to rupture or
malfunction, install a pressure relief device downstream of
the regulator. The relief pressure and flow capacity of the
relief device must satisfy system requirements.
The accuracy of the indication of pressure gauges can
change, both during shipment (despite care in packaging)
and during the service life. If a pressure gauge is to be used
with these products and if inaccurate indications may be
hazardous to personnel or property, the gauge should be
calibrated before initial installation and at regular intervals
during use.
Before using these products with fluids other than air, for
non industrial applications, or for life-support systems
consult Norgren.
TECHNICAL DATA
Fluid: Compressed air
Maximum pressure: 20 bar (300 psig)
Operating temperature*: -34° to +65°C (-30° to +150°F)
* Air supply must be dry enough to avoid ice formation at
temperatures below +2°C (+35°F).
Typical flow with 10 bar (150 psig) inlet pressure, 6,3 bar
(90 psig) set pressure and 1 bar (15 psig) droop from
set:
1/8" Ports: 6,5 dm
3
/s (14 scfm)
1/4" Ports: 7 dm3/s (15 scfm)
Gauge ports:
1⁄8 PTF with PTF main ports
Rc1/8 with ISO Rc main ports
Rc1/8 with ISO G main ports
Materials:
Body: Zinc
Bonnet : Acetal
Valve: Brass/nitrile
Valve seat: Acetal
Elastomers: Nitrile
REPLACEMENT ITEMS
Service kit (includes items circled on exploded view)
Relieving...............................................................3407-02
Non-relieving........................................................3407-01
Tamper resistant knob........................................18-001-092
PANEL MOUNTING DIMENSIONS
Panel mounting hole diameter: 30 mm (1.19")
Panel thickness: 2 to 6 mm (0.06" to 0.25")
INSTALLATION
1. Shut off air pressure. Install regulator in air line -
● with air flow in direction of arrow on body,
● upstream of lubricators and cycling valves.
● as close as possible to the device being serviced.
● at any angle.
2. Connect piping to proper ports using pipe thread sealant
on male threads only. Do not allow sealant to enter
interior of regulator.
3. Install a pressure gauge or plug the gauge ports. Gauge
ports can also be used as additional outlets for regulated
air.
4. Install a Norgren general purpose filter upstream of the
regulator.
ADJUSTMENT
1. Before applying inlet pressure to regulator, turn
adjustment (2 or 5A) counterclockwise to remove all
force on regulating spring (6).
2. Apply inlet pressure, then turn adjustment clockwise to
increase and counterclockwise to decrease pressure
setting.
3. Always approach the desired pressure from a lower
pressure. When reducing from a higher to a lower
setting, first reduce to some pressure less than that
desired, then bring up to the desired pressure.
NOTE
With non-relieving regulators, make pressure
reductions with some air flow in the system. If
made under no flow (dead-end) conditions, the
regulator will trap the over-pressure in the
downstream line.
4. Push adjusting knob down to lock pressure setting; pull
up to release. Install tamper resistant knob (see
Replacement Items) to make setting tamper resistant.
R07
Installation & Maintenance
Instructions
* Outlet pressure can be adjusted to pressures in excess of, and less than, those specified. Do not use these units to control pressures outside of the specified ranges.
Regulator
R07 - ★★★ - ★★★★
Thread Form
A....PTF
B....ISO Rc taper
G....ISO G parallel
Port
1....1/8"
2....1/4"
Spring (Outlet Pressure Range) *
A....0,1 to 0,7 bar (1 to 10 psig)
E....0,3 to 3,5 bar (5 to 50 psig)
K....0,3 to 7 bar (5 to 100 psig)
Diaphragm
R....Relieving
N....Non relieving
Gauge
G....With
N....Without
IM-300.200
(3/01)
Replaces NIP-231
© Norgren 2001
Option
0....Not applicable
Option
0....Standard
2....Low flow seat
Early Bonnet
Current Bonnet
Current Body (16) Valve seat (11) and
seal (12) used only
with current body.
Early Body (15) Valve seat (9) and
seal (10) used only
with early body.
17
18
5A
1
2
3
4
5
6
7
8
11
12
13
14
16
9
10
15
a subsidiary of IMI plc
Loading...