Littleton, CO USA Phone 303-794-2611 Fax 303-795-9487
ALE-7-1
Section 7
Contents
R30M Manifold Regulator 8mm and 10mm ports . . . . . . . . . . . . . .ALE-7-2
R72M Manifold Regulator 1/4" and 3/8" ports . . . . . . . . . . . . . . . . .ALE-7-4
Manifold Regulators
8mm, 10mm, 1/4" and 3/8" port
sizes.
R30M
R72M
See Section ALE-25 for Accessories
ALE-7-2
Littleton, CO USA Phone 303-794-2611 Fax 303-795-9487
R30M SERIES
● Push-in fittings in ports. No need for threaded
connectors and fittings
● Push to lock adjusting knob with tamper resistant
accessory
● Integral base mounting
● Water or compressed air only
Manifold Regulator
8 mm and 10 mm Port Sizes
ISO Symbols
Relieving Non relieving
Ordering Information. Models listed include 10 mm push-in fittings, knob adjustment, relieving diaphragm, 0 to 70 psig (0 to 4.8 bar) outlet pressure
adjustment range* with gauge, with porting plug.
† Typical flow with 150 psig (10 bar) inlet pressure, 90 psig (6.3 bar) set pressure and a 15 psig (1 bar) droop from set.
Port Model Flow†scfm (dm3/s) Weight lb (kg)
8 mm R30M-8DK-RGG 17 (8) 0.22 (0.10)
10 mm R30M-ADK-RGG 17 (8) 0.22 (0.10)
03R M
-
★
D
-
★
K
★ ★
* Outlet pressure can be adjusted to pressures in
excess of, and less than, those specified.Do not
use these units to control pressures outside of the
specified ranges.
Alternative Models
Gauge Substitute
With G
Without N
Port Size Substitute
8 mm 8
10 mm A
Outlet Pressure Adjustment Ranges* Substitute
0 to 70 psig (0 to 4.8 bar) G
5 to 100 psig (0.3 to 7 bar) K
Push-In Form Substitute
Metric D
Type Substitute
Relieving R
Non relieving N
Adjustment Substitute
Knob K
ALE-7-3
All Dimensions in Inches (mm)
R30M Manifold Regulators
Littleton, CO USA Phone 303-794-2611 Fax 303-795-9487
Technical Data
Fluid: Compressed air or water
Maximum pressure: 150 psig (10 bar)
Operating temperature*: 23° to 104°F (-5° to 40°C)
* Air supply must be dry enough to avoid ice formation at temperatures below 35°F (2°C).
Approximate flow at 150 psig (10 bar) inlet pressure, 90 psig (6.3 bar) set pressure
and a droop of 15 psig (1 bar) from set: 17 scfm (8 dm3/s)
Gauge port:
(can be used as additional outlet port)
10 mm OD tube with 10 mm OD tube main ports
8 mm OD tube with 8 mm OD tube main ports
Two inlet ports:
10 mm OD tube or 8 mm o/d tube
One outlet port:
10 mm OD tube with 10 mm OD tube inlet
8 mm OD tube with 8 mm OD tube inlet
Materials:
Body: Acetal
Bonnet: Acetal
Valve: Brass/nitrile
Elastomers: Nitrile
Valve seat: Acetal
Typical Performance Characteristics
2.52 (64)
1.89 (48)
0.95 (24)
2.56 (65)
3.19 (81)
Panel mounting hole diameter: 1.19" (30 mm)
Maximum panel thickness: 0.25" (6 mm)
Typical Manifold Regulator Application
psig
bar g
8
100
6
80
60
4
OUTLET PRESSURE
40
2
20
0
0
0 8 16 24 32 40 48 scfm
0 4 8 12 16 20 dm3/s
FLOW CHARACTERISTICS (AIR)
INLET PRESSURE: 150 psig (10 bar g)
RANGE: 5 to 100 psig (0.3 to 7 bar)
AIR FLOW
PORT SIZE: 10 mm
Booster signal
Pressure
in
See Section ALE-25 for Accessories
ALE-7-4
Littleton, CO USA Phone 303-794-2611 Fax 303-795-9487
R72M
● Excelon design allows in-line or modular installation
● Manifold typically up to six regulators without
booster signal
● Balanced valve design for optimum pressure control
● Push to lock adjusting knob with tamper resistant
accessory
● Modular installations with Excelon 72, 73, and 74
series can be made to suit particular applications
Excelon 72 Manifold Regulator
1/4",3/8" Port Sizes
ISO Symbols
Relieving Non Relieving
Ordering Information. Models listed include PTF threads, knob adjustment, relieving diaphragm, 5to 150 psig (0.3 to 10 bar) outlet pressure
adjustment range* with gauge.
† Typical flow with 150 psig (10 bar) inlet pressure, 90 psig (6.3 bar) set pressure and a 15 psig (1 bar) droop from set.
Inlet Port (2) Outlet Port (1) Model Flow†scfm (dm3/s) Weight lb (kg)
1/4" 1/4" R72M-2AK-RMG 83 (39) 0.79 (0.36)
3/8" 1/4" R72M-3AK-RMG 83 (39) 0.79 (0.36)
R 7 2
-
★ ★ ★
-
★★ ★ ★
Inlet Port Size Substitute
1/4" 2
3/8" 3
Threads Substitute
PTF A
ISO Rc taper B
ISO G parallel G
Diaphragm Substitute
Relieving R
Non relieving N
Gauge Substitute
With G
Without N
* Outlet pressure can be adjusted to
pressures in excess of, and less than, those
specified. Do not use these units to control
pressures outside of the specified ranges.
Adjustment Substitute
Knob K
T-bar T
Alternative Models
Outlet Pressure Adjustment Range* Substitute
5 to 30 psig (0.3 to 2 bar) C
5 to 60 psig (0.3 to 4 bar) F
5 to 150 psig (0.3 to 10 bar) M
Type Substitute
Manifold M
ALE-7-5
All Dimensions in Inches (mm)
R72M Manifold Regulators
Littleton, CO USA Phone 303-794-2611 Fax 303-795-9487
Technical Data
Fluid: Compressed air
Maximum pressure: 290 psig (20 bar)
Operating temperature*: -30° to 150°F (-34° to 65°C)
* Air supply must be dry enough to avoid ice formation at temperatures below 35°F (2°C).
Typical flow at 150 psig (10 bar) inlet pressure, 90 psig (6.3 bar) set pressure and
a droop of 15 psig (1 bar) from set: 83 scfm (39 dm3/s)
Two inlet ports:
1/4" or 3/8" PTF
1/4" or 3/8" ISO Rc
1/4" or 3/8" ISO G
One outlet port:
1/4" PTF with PTF inlet ports
1/4" ISO Rc with ISO Rc inlet ports
1/4" ISO Rc with ISO G inlet ports
One gauge port:
1/8" PTF with PTF inlet ports
1/8" ISO Rc with ISO Rc inlet ports
1/8" ISO Rc with ISO G inlet ports
Materials
Body: Zinc
Bonnet: Acetal
Valve: Brass
Elastomers: Nitrile
Bottom plug: Acetal
Typical Performance Characteristics
Typical Manifold Regulator Application
R72M R72M R72M R72M R72M R72M
Pressure
in
Booster signal
1.97 (50)
1.97 (50)
2.48 (63)
1.89 (48)
2.36 (60)
2.88 (73)
1.31 (33)
4.03 (102)
1.31 (33)
1.01 (26)
1.01 (26)
1.89 (48)
2.36 (60)
P1 P1 P1 P1
Panel mounting hole diameter: 1.57" (40 mm)
Maximum panel thickness: 0.16" (4 mm)
Service Kits
Item Type Part Number
Service kit
Relieving 4381-500
Non relieving 4381-501
Service kit includes diaphragm assembly, valve assembly,
valve spring and o-rings.
Outlet
Pressure
psig
bar g
8
100
6
80
60
4
OUTLET PRESSURE
40
2
20
0
0
0 20 40 60 80 100 120 scfm
0 10 20 30 40 50 dm3/s
FLOW CHARACTERISTICS
INLET PRESSURE: 150 psig (10 bar g)
RANGE: 5 to 150 psig (0.3 to 10 bar)
AIR FLOW
PORT SIZE: 3/8"
"
1/8
Gauge Port
"
"
or 3/8"
1/4
Inlet Port
"
1/4
Outlet Port
or 3/8"
1/4
Inlet Port
Loading...