Norgren B07 Datasheet
See Section ALE-24 for Accessories
Littleton, CO USA Phone 303-794-2611 www.norgren.com
B07
● Compact design
● Full flow gauge ports
● Low torque, non-rising adjusting knob
● Snap action knob locks pressure setting when
pushed in
● Standard relieving models allow reduction of outlet
pressure even when the system is dead-ended
● Protects air operated devices by removing liquid and
solids contaminants
● Screw-on bowl reduces maintenance time
● Can be disassembled without the use of tools or
removal from the air line
Series 07 General Purpose Filter/Regulator
1/8" and 1/4" Port Sizes
ALE-12-2
ISO Symbols
Automatic Drain
Relieving
Manual Drain
Relieving
Automatic Drain
Non Relieving
Manual Drain
Non Relieving
Alternative Models
-
★★★ ★★ ★
-
0★B 7
Threads Substitute
PTF A
ISO Rc taper B
ISO G parallel G
Drain Substitute
Automatic A
Manual M
Port Size Substitute
1/8
"
1
1/4
"
2
Element Substitute
5 µm 1
Bowl Relief Type Gauge Substitute
Transparent Relieving Without 01
Transparent Relieving With 02
Transparent Non-relieving Without 03
Transparent Non-relieving With 23
Metal Relieving Without 33
Metal Relieving With 34
Metal Non-relieving Without 35
Metal Non-relieving With 36
Outlet Pressure Adjustment Ranges* Substitute
1 to 10 psig (0.1 to 0.7 bar) A
5 to 50 psig (0.3 to 3.5 bar) E
5 to 100 psig (0.3 to 7 bar) K
5 to 125 psig (0.3 to 8.6 bar) L
Ordering Information. Models listed include PTF threads, transparent bowl, relieving diaphragm, gauge, automatic drain, 5 µm element, 5 to
100 psig (0.3 to 7 bar) outlet pressure adjustment range* .
Port Size Model Number Flow† scfm (dm3/s) Weight lbs (kg)
1/8" B07-102-A1KA 13 (6.2 dm3/s) 0.57 (0.26)
1/4" B07-202-A1KA 14 (6.5 dm3/s) 0.57 (0.26)
* Outlet pressure can be adjusted to pressures in excess of, and less than, those specified. Do not use these units to control pressures outside of the specified
ranges.
† Typical flow with 100 psig (7 bar) inlet pressure, 90 psig (6.3 bar) set pressure and a 15 psig (1 bar) droop from set.
B07 Filter/Regulators
Littleton, CO USA Phone 303-794-2611 www.norgren.com
ALE-12-3
All Dimensions in Inches (mm)
Automatic Drai
n
Manual Drai
n
2.13 (54)
1.63 (41)
1.50 (38)
1.50 (38)
8.41 (214)**
1.12 (28)
2.67 (68)
6.44 (164)
1.1 (28)
8.26 (210)**
1.12 (28)
2.67 (68)
6.29 (160)
1.1 (28)
** Minimum clearance to remove bowl
Panel mounting hole diameter 1.19" (30 mm)
Panel thickness: 0.25" (6 mm)
PORT SIZE: 1/4"
ELEMENT: 40 µm
INLET PRESSURE: 150 psig (10 bar g)
RANGE: 5 to 100 psig (0.3 to 7 bar)
FLOW CHARACTERISTICS
0 2 4 6 8 10 dm3/s
AIR FLOW
0 4 8 12 16 20 24 scfm
OUTLET PRESSURE
8
6
4
2
0
bar g
100
80
60
40
20
0
psig
Typical Performance Characteristics
Service Kits
Item Type Part number
Service kit
Relieving models, 5 µm element 3820-12
Non relieving models, 5 µm element 3820-11
Replacement drains
Manual 773-03
Automatic 3654-02
Service kit includes slip ring, diaphragm, valve seat with o-ring,
valve, valve spring, element, element gasket, and bowl o-ring.
Technical Data
Fluid: Compressed air
Maximum pressure
Transparent bowl: 150 psig (10 bar)
Metal bowl: 250 psig (17 bar)
Operating temperature*
Transparent bowl: 30° to 125°F (-34° to 50°C)
Metal bowl: -30° to 150°F (-34° to 65°C)
* Air supply must be dry enough to avoid ice formation at temperatures below 35°F (2°C)
Particle removal: 5 µm or 40 µm filter element
Air quality: Within ISO 8573-1, Class 3 and Class 5 (par ticulates)
Typical flow at 100 psig (7 bar) inlet pressure, 90 psig (6.3 bar) set pressure and a
droop of 15 psig (1 bar) from set
1/8" Ports: 13 scfm (6.2 dm3/s) with 5 µm element
1/4" Ports: 14 scfm (6.5 dm3/s) with 5 µm element
Nominal bowl size: 1 fluid ounce (31 ml)
Gauge ports:
1/8" PTF with PTF main por ts
1/8" ISO Rc with ISO Rc main ports
1/8" ISO Rc with ISO G main ports
Drain connection: Will fit 1/8-27 and 1/8-28 pipe thread
Automatic drain operation: Spitter type drain operates momentarily when a rapid
change in air flow occurs or when the supply pressure is reduced.
Materials:
Body: Zinc
Bonnet: Acetal
Valve: Brass/nitrile
Valve seat: Acetal
Bowl
Transparent: Polycarbonate
Metal: Zinc
Element: Sintered polypropylene
Elastomers: Nitrile
Loading...