Nordmende DSSN60BL, DSSN60IX User Manual [nl]

Dishwasher

Instruction

Instruction Manual

InstructionInstruction

Manual

Manual Manual

Gebrauchsanweisung

GebrauchsanweisungGebrauchsanweisung

DSSN60BL

DSSN60BL –––– DSSN60IX

DSSN60BL DSSN60BL

Geschirrspüler

DSSN60IX

DSSN60IX DSSN60IX

CONTENTS

Getting familiar with your machine ……………………………………………

• Technical specifications ……………………………………………………..

• Conformity with the standards and Test data ……………………………..

Safety information and Recommendations………………………………….. 6

• Recycling .......……………………….........................................................

• Safety information ……………………………………………………………

• Recommendations …...………………………………………………………

• Items not suitable for dishwashing …………………………………………

Installing the machine ………………………………………………………….. 8

• Positioning the machine ……………………………………………………..

• Water connections …………………...............................................................

• Water inlet hose ….…………………………………………………………..

• Water outlet hose …..………………..............................................................

• Electrical connection…………………………………………………………

Preparing the machine for use ………………………………………………… 11

• The importance of water decalcification …………………………………..

• Filling with salt ………………………………………………………………..

• Testing strip……………………………………………………………………

• Adjusting salt consumption………………………………………………….

• Detergent usage ……………………........................................................

• Filling the detergent compartment………………………………………….

• Combined detergent….………………………………………………………

• Filling with rinse aid and making the setting……………………………….

Loading your dishwasher .……………………………………………………. 16

• Top basket…………………………………………………………………...

• Lower basket………………………………………………………………...

• Alternative basket loads …………………………………………………...

• Standard loading and Test data …………………………………………..

Programme descriptions .……………………………………………………..

• Programme items …………………………………………………………..

Switching on the machine and selecting a programme……………........ 21

• Switching on the machine………………………………………………….

• Programme follow-up ………………………………………………………

• Changing a programme ……………………………………………………

• Changing a programme with resetting …………………………………...

• Switching the machine off ….……………………………………………...

Maintenance and Cleaning ........................................................................ 23

• Filters ..………………………………………………………………………

• Spray arms ………………………………………………………………….

• Hose filter ……………………………………………………………………

Failure codes and what to do in case of failure …………………………

Practical and useful information……......................................................... 27

Upper basket with racks

Upper spray arm

Lower basket

Lower spray arm

Filters

Rating plate

Control Panel

Detergent and rinse-aid dispenser

Cutlery basket

10.

Lower basket handle

11.

Salt dispenser

12.

Upper basket track latch

13.

Upper basket handle

Active drying unit: This system provides better drying performance for your dishes.

GETTING FAMILIAR WITH YOUR MAC

HINE

1.) Power On/Off Button When the Power On/Off button is pressed, the lamp on the Start/Pause button starts lighting.

2.) Door Handle The door handle is used to open/close the door of your machine.

3.) Delay Timer Button

Thanks to the delay feature of your machine, you can delay the start time of the program for 3-6-9-12 hours by pressing Delay button. When you pres delay button, 3h washing lamp comes on. If you continue pressing Delay Button, 6h-9h-12h lamps will come on

respectively on each press. If you press delay button again after 12h lamp comes on, then you cancel delay time. If you select delay time and press Start/Pause button, then you activate delay time. If you want to change delay time, you can adjust the new time by pressing Start/Pause button and delay button. Press Start/Pause button again in order to activate. From this moment, the countdown starts. When delay time is completed, delay lamp goes off, and the washing program you selected starts operating.

• If you press Delay button while 12h delay lamp is lightened, delay lamp will go off. When you press Start/Pause button with delay lamp off, the selected program starts without any delay.

• When you delay a program, you can check the remaining time through delay lamps. For example; when you select 12h delay time, 12h delay lamp comes on. When remaining time is down to 9h, then 9h lamp comes on. In this way, you can follow up the remaining time.

4.) Prewash Button

If you select an extra pre-washing program, you improve washing performance. When you select pre-washing, since it improves washing performance, it changes the temperature and washing time of some programs. Note 1: If you will only make pre-washing, start the machine pressing the start/ stop key after pressing the pre-wash key while the program is at the cancel position.

5.) ½ Half Load Button

Using the function ½ , three sorts of washing up can be done those being lower basket, upper basket and both baskets.

If you have little amount of dishes in your machine and if you have to wash them, you can also activate the semi-filling function additionally. If you have dishes in both baskets, press the key ½ and select the position in

which both lamps are highlighted.

If you have dishes only in the upper basket, pres the key ½ and select the position in which the upper lamp is illuminated. Thus, washing up shall be done only on the

upper basket of your machine. No dishes should certainly be available in the lower basket while using this feature. If you have dishes only in the lower basket, press the key ½ and

select the position in which the lower lamp is illuminated. Thus, washing up shall be done only on the lower basket of your machine. In using this feature, make sure that there are no dishes in the upper basket.

Note 2: If you have used an extra feature on the latest washing program, this feature will remain active also on the next washing program. If you do not want to use this feature on the newly

selected washing program, press the selected feature button again, and check that the lamp on the button goes off.

6.) Start/Pause Button

Once you press the Start/Pause button, the programme you selected with the programme selector button will start running and the status indicator lamp “wash” will light up.In the stop condition while wash led is On, Start/Pause led will blink.

7.) Programme selector knob With the programme selector knob, you can select a suitable programme for your dishes.

8.) Salt Lack Warning Indicator

In order to see whether softening salt in your machine is sufficient or not, check salt lack warning lamp on the display. When salt lack warning lamp starts coming on, you need to fill in the salt chamber.

Rinse Aid Lack Warning Indicator

In order to check that there is sufficient rinse aid in your machine, check rinse aid lack warning lamp on the display. When rinse aid lack warning lamp starts coming on, fill in rinse aid chamber. Note 3: During washing or when 3 in 1 detergent is used, salt and rinse aid lack warning indicator lamps will go off even if there is not sufficient salt and rinse aid in the machine.

9.) Program Monitor Lights Program flow can be monitored via program monitor lights on control panel.

• Wash

• Rinse

• Dry

• End

Child Lock Operation

In order to activate child lock, press Start/Pause and Delay buttons simultaneously for 4 seconds. When activated, 3h (washing) lamp flashes once. The same operation is performed in order to cancel child lock. When child lock is cancelled, 3h (washing) lamp flashes twice.

Technical specifications

Width ……………………………..

Net Weight ……………………...

Heating Power …………………..

Pump Power …………………….

Drain Pump Power ……………..

Capacity ………………………… Height …………………. ……….

Depth …………………………….

Electricity input ……………........

Total Power ……………………..

Water supply pressure...............

Current …………………………..

12 place settings 815-870 mm 596 mm 570 mm 42 kg 220-240 V, 50 Hz 2200 W 2000 W 100 W 30 W

0.03 MPa (0,3 bar) - 1 MPa (10 bar) 10 A

• Producer company has its right to amend design and technical specifications reserved.

• The machine's service life is 10 years (the duration required to keep spare parts for the machine

to fulfil its usage functions).

Conformity with the standards and Test data / EC Declaration of Conformity

All stages related to the machine are executed in accordance with the safety rules provided in all relevant directives of the European Community.

2004/108/EC, 2006/95/EC, IEC 436/DIN 44990, EN 50242

SAFETY INFORMATION AND RECOMMENDATIONS

Recycling

• Certain components and the packaging of your machine have been produced from recyclable

materials.

• Plastic parts are marked with international abbreviations:

(>PE< , >PS< , >POM<, >PP<, ….)

• Cardboard parts have been produced from recycled paper and they should be disposed of into

waste paper collection containers for recycling.

• Such materials are not suitable for being disposed of into garbage bins. They should be delivered

to recycling centres instead.

• Contact relevant centres in order to obtain information on methods and points of disposal.

Safety Information

When you take delivery of your machine

• Check for any damage to your machine or to its packaging. Never start a machine damaged in

any way, make sure to contact an authorised service.

• Unwrap the packaging materials as indicated and dispose of them in accordance with the rules.

The points to pay attention during machine installation

• Choose a suitable, safe and level place to install your machine.

• Carry out the installation and connection of your machine by following the instructions.

• This machine should be installed and repaired by an authorised service only.

• Only original spare parts should be used with the machine.

• Before installing, be sure that the machine is unplugged.

• Check whether the indoor electrical fuse system is connected according to the regulations.

• All electrical connections must match the values indicated on the rating plate.

• Pay special attention and be sure that the machine does not stand on the electricity supply cable.

• Never use an extension cord or a multiple socket for making a connection. The plug should be

comfortably accessible after the machine has been installed.

• Please assemble the dishwasher, which is inserted under or in the kitchen platform, according to the instruction. Be sure that the product is fixed properly

• After installing the machine to a suitable place , run it unloaded for the first time.

In daily use

• This machine is for household use, do not use it for any other purpose.

dishwasher will void the guarantee.

• Do not get up, sit or place a load on the open door of the dishwasher, it may fall over.

• Never put into the detergent and rinse aid dispensers of your machine anything other than those

detergents and rinse aids which are produced specifically for dishwashers. Our company will not be responsible for any damage that might occur in your machine otherwise.

• The water in the machine's washing section is no drinking water, do not drink it.

• Due to danger of explosion, do not put into the machine’s washing section any chemical

dissolving agents such as solvents.

• Check whether plastic items are heat-resistant before washing them in the machine.

• Do not put into your machine those items which are not suitable for dishwashing. Also, do not fill

any basket above its capacity. Our company will not be responsible for any scratch or rust to form on the inner frame of your machine due to basket movements otherwise.

• Especially because hot water may flow out, the machine door should not be opened under any

circumstances while the machine is in operation. In any case, a safety devices ensures that the machine stops if the door is opened.

• Do not leave your dishwasher’s door open. Failure to do so may lead to accidents.

• Place knives and other sharp-ended objects in the cutlery basket in blade-down position.

• This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

For your children’s safety

• After removing the machine’s packaging, make sure that the packaging material is out of reach of

children.

• Do not allow children to play with or start the machine.

• Keep your children away from detergents and rinse aids.

• Keep children away from the machine while it is open because there may still be residues of

cleaning substances inside the machine.

• Be sure that your old machine does not pose any threat to your children. Children are known to

have gotten themselves locked in old machines. To forestall such a situation, break your machine's door lock and tear off the electrical cables.

In case of malfunctioning

• Any malfunction in the machine should be repaired definitely by qualified persons. Any repair

work performed by anyone other than the authorised service personnel will cause your machine to be left outside the scope of warranty.

• Prior to any repair work on the machine, be sure that the machine is cut off from the mains.

Switch off the fuse or unplug the machine. Do not pull by the cable when unplugging. Make sure to turn off the water tap.

Commercial usage of the

Recommendations

INSTALLING THE MACHINE

• For ener into the machine. Start your machine after having fully loaded it

• Use the pre-wash programme only whenever necessary.

• Place such hollow items as bowls, glasses and pots into the machine in such a way that they will

face down.

• You are recommended not to load into your machine any dishes different or more than indicated.

Items not suitable for dishwashing:

• Cigarette ashes, candle leftovers, polish, paint, chemical substances, iron-alloy materials;

• Forks, spoons and knives with wooden or bone, or ivory or nacre-coated handles; glued items,

items soiled with abrasive, acidic or base chemicals

• Plastic items that are not heat-resistant, copper or tin-coated containers;

• Aluminium and silver objects (they may discolour, become dull)

• Certain delicate glass types, porcelains with ornamental printed patterns as they fade even after

the first wash; certain crystal items as they lose their transparency over time, adhered cutlery that is not heat-resistant, lead crystal glasses, cutting boards, items manufactured with synthetic fibre;

• Absorbent items as sponges or kitchen rags are not suitable for dishwashing.

Warning: Take care to buy dishwasher-proof sets in your future purchases.

gy and water saving, remove coarse residues on your dishes before placing the dishes

Positioning the machine

When determining the place to put your machine on, take care to choose a place where you can easily load and unload your dishes.

Do not put your machine in any location where there is the probability for the room temperature to fall below 0°C.

Before positioning, take the machine out of its packaging by following the warnings located on the package.

Position the machine close to a water tap or drain. You need to site your machine, taking into consideration that its connections will not be altered once they are made.

Do not grip the machine by its door or panel in order to move it.

Make sure that the water inlet and outlet hoses do not get squeezed while positioning the machine. Also, make sure that the machine does not stand on the electrical cable.

Adjust the machine’s adjustable feet so that it can stand level and balanced. Proper positioning of the machine ensures problem-free opening and closing of its door.

If the door of your machine does not close properly, check if the machine is stable on the floor it stands; if not, adjust the adjustable feet and ensure its stable position.

Water connection Be sure that the indoor plumbing is suitable for installing a dishwasher. Also, we recommend that you fit a filter at the entrance of your place or apartment so as to avoid any damage to your machine because of any contamination (sand, clay, rust etc.) that might be occasionally carried in through the mains water supply or the indoor plumbing, and to forestall such complaints as yellowing and formation of deposits after washing.

Water inl

Do not use the water inlet hose of your old machine, if any. Use the new water inlet hose supplied with your machine instead. If you are going to connect a new or long-unused water inlet hose to your machine, run water through it for a while before making the connection. Connect the water inlet hose directly to the water inlet tap. The pressure supplied by the tap should be at a minimum of 0.03 Mpa and and at a maximum of 1 Mpa. If the water pressure is above 1 Mpa, a pressure-relief valve should be fitted inbetween. After the connections are made, the tap should be turned on fully and checked for water tightness. For the safety of your machine, make sure to always turn off the water inlet

et hose

tap after each wash programme is finished.

NOTE: Aquastop water spout is used in some models. In case of using Aquastop, a dangerous tension exists. Do not cut Aquastop water spout. Do not let it get folded or twisted.

Water outl

The water drain hose can be connected either directly to the water drain hole or to the sink outlet spigot. Using a special bent pipe (if available), the water can be drained directly into the sink via hooking the bent pipe over the edge of the sink. This connection should be at a minimum of 50 cm and and at a maximum of 110 cm from the floor plane. Warning: When a drain hose longer than 4 m is used, the dishes might remain dirty. In that case, our company will not accept responsibility.

et hose

Electrical connection

The earthed plug of your machine should be connected to an earthed outlet supplied by suitable voltage and current. If there is no earthing installation, have a competent electrician carry out an earthing installation. In case of usage without earthing installed, our company will not be responsible for any loss of usage that might occur.

The indoo

r fuse current value should be 10-16 A. Your machine is set according to 220-240 V. If the mains voltage in your location is 110 V, connect a transformer of 110/220 V and 3000 W inbetween. The machine should not be plugged in during positioning. Always use the coated plug supplied with your machine.

Running in low voltage will cause a decline in washing quality.

The machine’s electrical cable should be replaced by an authorised service or an authorised electrician only. Failure to do so may lead to accidents.

For safety purposes, always make sure to disconnect the plug when a wash programme is finished.

In order not to cause an electric shock, do not unplug when your hands are wet.

When disconnecting your machine from the mains supply, always pull from the plug. Never pull the cord itself.

Prior to using the machine for the first time

PREPARING THE MACHINE FOR USE

• Check wh

installation instructions for the machine.

• Remove all packaging materials inside the machine.

• Set the water softener.

• Add 2 kg salt into the salt compartment and fill with water up to a level at which it will almost

overflow.

• Fill the rinse aid compartment.

ether the electricity and supply water specifications match the values indicated by the

The importance of water decalcification

For a good washing function, the dishwasher needs soft, i.e. less calcareous water. Otherwise, white lime residues will remain on the dishes and the interior equipment. This will negatively affect your machine’s washing, drying and shining performance. When water flows through the softener system, the ions forming the hardness are removed from the water and the water reaches the softness required to obtain the best washing result. Depending on the level of hardness of the inflowing water, these ions that harden the water accumulate rapidly inside the softener system. Therefore, the softener system has to be refreshed so that it operates with the same performance also during the next wash. For this purpose, dishwasher salt is used.

Filling with salt

Use softener salt specifically produced for use in dishwashers. To put softener salt, first remove the

compartment gets filled with water. Therefore, put the softener salt prior to starting your machine. This way, overflowing salt gets immediately cleaned up through the wash operation. If you are not going to wash any dishes immediately after putting salt, then run a short washing program with an empty machine in order to avoid any damage ( to prevent corrosion )to your machine due to the salt overflow while filling in the salt container.

lower basket and then open the salt compartment cap by turning it counter clockwise.1 2 At first the compartment with 2kg salt and water3 at overflowing level If available,using the funnel4 provided w refit the cap and close it. If the salt warning lamp on the control panel becomes on fill the salt compartment with salt again.

Fill the salt compartment with water at first use only.

If you put a tablet into the salt compartment, do not fill the compartment completely. We recommend that you use smallgrained or powder softener salt. Do not put table salt into your machine. Otherwise, the function of the softener compartment may decrease over time. When you start your dishwasher, the salt

ill make filling easier.;

fill

SALT

Testing s

trip

The washing effectiveness of your machine depends on the softness of the tap water. For this reason, your machine is equipped with a system that reduces the hardness in mains water supply. The washing effectiveness will increase when the system is correctly set. To find out the water hardness level of water in your area, contact your local water board or determine water hardness level by using the test strip(if available).

Open the testing strip.

Adjusting salt consumption

Run water through your tap for 1 min.

Keep the testing strip in water for 1 sec.

Shake the testing strip after taking it out of water.

Wait for 1 min.

Make your machine’s water hardness setting according to the result obtained through the testing strip.

Table of Water Hardness Level Settings

Water hardness l

evel

German hardness dH

0-5

6-11

French hardness dF

0-9

10-2

British hardness dE

7-14

Hardness Level Indicator

Wash lamp is on.

Rinse lamp is on.

12-17

18-22

21-

31-

15-21

22-28

Dry lamp is on.

End lamp is on.

23-31

41-

29-39

Wash and End lamps are on.

32-50

56-

40-63

Rinse and End lamps are on.

If the hardness of the water you use is above 90 dF (French hardness) or if you are using well water; you are recommended to use filter and water refinement devices.

NOTE: Hardness level is adjusted to level 3 as a factory settin Adjust the water softener according to how hard your tap water is.

Move the programme selector knob to the 0 (Reset) position while your machine is not

in operation.1

After resetting your machine, press the Start/Pause button and keep it pressed

down.2

Meanwhile, energise the machine by pressing the Power On/Off button. 4

Keep Start/Pause keys press until program monitor lights are on and off. 2

After the lamps “3h-6h-9h-12h” 3 have flashed, release the Start/Pause button. 2

Your machine displays the latest entered water hardness setting.

You can adjust the levels by pressing the Start/Pause button 2 according to Table

of Water Hardness Level Settings.

After adjusting the water hardness level , press on/off button to save the settings

in memory. 4

Detergent usage

Use a det

ergent specifically designed for use in domestic dishwashers.

You can find powder,gel,and tablet detergents in the market that have been designed for household dishwashers.Detergent should be put into the compartment prior to starting the

machine. Keep your detergents in cool, dry places out of reach of your children. Do not fill detergent into the detergent compartment more than required; otherwise it may cause scratches on your glasses as well as lead to a poorly dissolved detergent. Should you need more information concerning the detergent you will use, contact detergent manufacturers directly.

Filling the detergent compartment

Push the latch to open the detergent container as shown in the image. 1 Detergen

t pod has level lines inside. It is possible to measure the right detergent amount using these lines. Detergent pod can take totally 40 cm3 detergent. Open the dishwasher detergent and pour into the larger compartment b 25 cm3 if y

our dishes are heavily soiled or 15 cm3 if they are less soiled.2 If your dishes have bee

n kept dirty for a very long time, if there are dried food wastes on them, and if you have overly loaded the dishwasher, pour a 5 cm3 deterge

nt into the pre-wash compartment and start your machine. You may have to add more detergent into your machine, depending on the degree of soil and on the water hardness level in your area.

Combined detergent

Detergent manufacturers also produce combined detergents called “2 in 1”, “3 in 1” or “5 in 1” etc.

“2 in 1” detergents contain detergent + salt or rinse aid. When using “2 in 1” detergents make sure to check the specifications of the tablet.

Other tablet detergents contain detergent + rinse aid + salt + varlous extra functions.

Generally, combined detergents produce sufficient results under certain usage conditions only. Such detergents contain rinse aid and/or salt in preset amounts

Points to consider when using this type of products:

• Always make sure to check the specifications of the product you will use or whether or not

it is a combined product.

• Check if the detergent used is appropriate for the hardness of mains water that machine is

appertaining to.

• Observe the instructions on packagings when using such products.

• If such detergents are in the form of tablets, never put them into the interior section or the

cutlery basket of the dishwasher. Always put the tablets into the detergent compartment in the detergent dispenser.

• They produce good results for certain types of usage only. If you are using this type of

detergents, you need to contact the manufacturers and find out about the suitable conditions of use.

• When the conditions of use of such products and the machine settings are appropriate,

they ens

ure savings in salt and/or rinse aid consumption.

• Contact the detergent manufacturers if you are not obtaining good wash results (if your

dishes stay calcareous and wet) after having used 2 in 1 or 3 in 1 detergents. The scope of warranty for your machine does not cover any complaints caused by the use of these types of detergents.

Recommended usage: If you want to obtain better results while using combined detergents, add salt and rinse aid into your machine and adjust the water hardness setting and the rinse aid setting to the (1) lowest position.

Solubility of the tablet detergents produced by different companies can vary

depending on the temperature and time. Therefore, it is not recommended to use such detergents in short programs. It is more suitable to use powder detergents in such programs.

Warning: Should any problem, which you have not encountered before, arise with the use of this type of detergents, contact the detergent manufacturers directly.

When you give up using combined detergents

• Fill the salt and rinse aid compartments.

• Adjust the water hardness setting to the highest position ( 6 ) and run an empty-wash.

• Adjust the water hardness level.

• Make the suitable rinse aid setting.

Filling with rinse aid and making the setting

Rinse aid is used to prevent the stay of white water drops, lime stains, white film strip-shaped stains that may form on the dishes, as well as to increase the drying performance. Contrary to the popular beliefs, it is used not only for obtaining shinier dishes but also for obtaining sufficiently dried dishes. For this reason, care should be taken that there is adequate amount of rinse aid in the rinse aid compartment and only polishing material produced for use at dishwashers should be used. If the rinse aid lamp on the control panel becomes on fill the rinse

aid compartment with rinse. To put rinse aid, remove the rinse aid compartment cap by turning it.1 Fill the compartment with rinse aid until the rinse aid level indicator becomes dark;2 refit th

rinse aid

e cap and close it by turning it in a way that the nails will correspond to one another. By checking the rinse aid level indicator on the detergent dispenser, you can understand whether or not your machine needs rinse aid. A dark indicator b means that there is rinse aid in the compartment, while a

light indicator a shows that you need to fill the compartment with rinse aid. The rinse aid level adjuster can be set to a position between 1 and 6. Factory setting for rinse aid is the position 3. You need to increase the degree of the adjuster if water stains form on your dishes after a wash, whereas you need to

decrease the degree if a blue stain is left when wiped by hand.3 Warning: Us

e only those rinse aid materials which are allowed for use in the machine. As rinse aid residues left as a result of overflowing will create extremely high amounts of foam and thus reduce the washing performance, remove the excess amount of rinse aid by wiping it with a rag.

LOADING YOUR DISHWASHER

If you prope

rly place your dishes into the machine, you will be using it in the best way in terms

of energy consumption, washing and drying performance. There are two separate baskets for you to load your dishes into your machine. You can load into the lower basket such round and deep items as pots with long handles, pot lids, plates, salad plates, cutlery sets. The upper basket has been designed for tea plates, dessert plates, salad bowls, cups and glasses. When placing long-stem glasses and goblets, lean them against the basket edge, rack or glass supporter wire and not against other items. Do not lean long glasses against one another or they cannot remain steady and may receive damage. It is more appropriate to locate the thin narrow parts into the middle sections of baskets. You can place spoons among the other cutlery sets in order to prevent them from sticking to one another. You are recommended to use the cutlery grid in order to obtain the best result. To avoid any possible injuries, always place such long-handle and sharp-pointed dishes as serving fork, bread knife etc. with their sharp points facing down or horizontally on the baskets.

Warning: Place your dishes into your machine in a way that they will not prevent the upper and lower spray arms from spinning. Top basket Dish rack There are dish racks on the upper basket of your machine. a b You can use

these dish racks in open or closed position. When they are in open position a you can place your cups on them; and when in closed position b you can pla

ce long glasses on the basket. Also, you can use these racks by placing long forks, knives and spoons on them laterally.

Top basket height adjustment

Top basket of your machine is in upper position. When it is in this position, you can place big items such as pans, etc. on lower basket. When you take top basket to lower position, you can place and wash big sized plates on the top basket. Use wheels in order to change the basket height. Open the basket retaining parts at the end of top basket rails by turning them to the sides, and take the basket out. Change the position of the wheels; reinstall the basket to the rail, and close basket retainer parts. In this way, you take the top basket to lower position

Goblet clamp

It enables safe wash of your goblets with long foot and glasses. on one another, this way they can not remain stable and can be damaged during washing.

To create wide spaces when you do not want to use goblet clamp, turn to position

Lower Basket

Folding Racks

Folding racks consisting of four parts that are located on the lower basket of your machine are designed in order to let you place big items easier such as pots, pans, etc. If requested, each part can be folded separately, or all of them can be folded and larger spaces can be obtained. You can use folding racks by raising them upwards, or by folding.

Do not lean your long glasses

+ 42 hidden pages