CSG50LPGWH
CSG60LPGWH
EN
OPERATING AND INSTALLATION
INSTRUCTIONS OF
FREESTANDING GAS COOKER
Dear Customer,
Our goal is to offer you products with high quality that exceed your expectations. Your appliance is produced in modern facilities carefully and particularly tested for quality.
This manual is prepared in order to help you use your appliance that is manufactured by the most recent technology, with confidence and maximum efficiency.
Before using your appliance, carefully read this guide that includes the basic information for right and safe installation, maintenance and use. Please contact to the nearest Authorized Service for the installation of your product.
CE Declaration of conformity
This appliance has been designed to be used only for home cooking. Any other use (such as heating a room) is improper and dangerous.
This appliance has been designed, constructed, and marketed incompliance with:
•Safety requirements of the "Gas" Directive 2009/142/EC;
•Safety requirements of the "Low voltage" Directive 2006/95/EC;
•Safety requirements of the "EMC" Directive 2004/108/EC;
•Requirements of the Directive 93/68/EC.
CONTENTS:
1.BRIEF PRESENTATION OF PRODUCT
2.WARNINGS
3.INSTALLATION AND PREPARATIONS FOR USE
3.1Environment where the appliance to be installed
3.2Installation of product
3.3Adjustment of feet
3.4Gas connection
3.5Electric connection and safety
3.6Gas conversion
4.USE OF YOUR PRODUCT
4.1Use of gas burners
4.1.1Control of hob burners
4.1.2Control of oven burner
4.1.3Control of grill burner
4.1.4Use of mechanical minute minder
4.2Accessories used in oven
5.CLEANING AND MAINTENANCE
5.1Cleaning
5.2Maintenance
6.SERVICE AND TRANSPORT
6.1Basic troubleshooting before contacting service
6.2Information related to the transport
2
1. BRIEF PRESENTATION OF PRODUCT
9
10
1
2
|
|
|
8 |
|
|
|
|
7 |
|
|
|
|
6 |
|
|
|
|
11 |
|
|
|
|
12 |
15 |
3 |
4 |
5 |
13 |
|
|
|
|||
|
|
|
14 |
|
MODEL |
DEPTH |
WIDTH |
HEIGHT |
|
(cm) |
(cm) |
(cm) |
CSG60LPGWH |
60 |
60 |
90 |
|
|
|
|
CSG50LPGWH |
60 |
50 |
90 |
List of Components: |
|
1- Cooktop |
9- Grill Burner |
2- Control Panel |
10Oven Lamp |
3- Oven Door Handle |
11- Semi-Rapid Burner |
4- Cover |
12Rapid Burner |
5- Adjustable Feet |
13Auxillary Burner |
6- Oven Door |
14Pan Support |
7- Oven Tray |
15- Semi-Rapid Burner |
8- Wire Grid |
|
3
2. WARNINGS
TAKE ALL IMPORTANT SAFETY MEASURES AND READ THE MANUAL COMPLETELY BEFORE
USING THE APPLIANCE.
General Safety
•These warnings are provided in the interest of your safety. Read this manual carefully before using the appliance.
•This appliance has been designed for non-professional, domestic use only.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
•Your appliance is produced in accordance with the local and international standards and regulations applicable.
•The maintenance and repair works must be made only by authorized service technicians. The installation and repair works without following proper knowledge may endanger you.
•If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
•If your appliance has a hob made of glass;
•! WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of
electric shock.
•Do not try to lift or move the appliance by pulling the door handle.
•It is dangerous to alter or modify the specifications of the appliance in any way.
Installation
•The appliance must be installed by an authorized technician and put into use. The producer is not responsible for any damage that might be caused by defective placement and installation by unauthorized people.
•When you unpack the appliance, make sure that it is not damaged during transportation. In case of any defect; do not use the appliance and contact to the authorized maintenance service immediately. As the materials used for package (nylon, stapler, strafoam...etc) may cause harmful effects to children, they should be collected and removed immediately.
For authorized people;
•Compare the features of the electricity network with the technical information on the rating label before plugging the appliance in.
•Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and the adjustment of the appliance are compatible. The adjustment conditions for this appliance are stated on the label.
•This appliance is not connected to a combustion products evacuation device. It shall be installed and connected in accordance with current installation regulations. Particular attention shall be
4
2. WARNINGS
given to the relevant requirements regarding ventilation.
•The gas inlet of this product is on the right side of the appliance. If connection point needs to be moved to the left side of the appliance, you can request an extension pipe from your authorized service.
During Use
•When you first run your oven a certain smell will be emanated arising from the insulation materials and the heater elements. For this reason, before using your oven, run it empty at maximum temperature for 45 minutes. At the same time you need to properly ventilate the environment in which the product is installed.
•While your appliance operates, its outside surfaces heat up. The interior surfaces of oven and the flue outlet are quite hot. Even if the appliance is turned off, these parts keep its heat for a specific time. Do not touch onto hot surfaces and keep children away.
•Always use oven gloves to remove and replace food in the oven.
•Always stand back from the appliance when opening the oven door to allow any build up of steam or heat to release.
•Do not leave the cooker while cooking with solid or liquid oils. They may catch fire on condition of extreme heating. Never pour water to the flames that are caused by oil. Cover the saucepan or frypan with its cover in order to choke the flame that has occured in this case and turn the cooker off.
•! CAUTION: The use of a gas cooking appliance results in the production of heat, moisture and products of combustion in the room in which it is installed. Ensure that the kitchen is well ventilated especially when the appliance is in use, keep natural ventilation holes open or install a mechanical ventilation device(mechanical extractor hood).
•! CAUTION: This appliance is for cooking purposes only. It must not be used for other purposes, for example room heating.
•While using the grill burner, keep the oven door open and always use the grill deflector shield supplied with the product. Never use the grill burner with the oven door closed.
•If you will not use the appliance for a long time, plug it off. Keep the main control switch off. Also when you do not use the appliance, keep the gas valve off.
•! CAUTION: Turn off all the burners before shutting the lid.
The hob surface should be allowed to cool before closing the lid.
•When the door or drawer of oven is open, do not leave anything on it. You may unbalance your appliance or break the cover.
•Do not put heavy things or flammable or ignitable goods (nylon, plastic bag, paper, cloth...etc) into the drawer. This includes cookware with plastic accessories (e.g. handles).
5
2.WARNINGS
•Protect your appliance against atmospheric effects. Do not leave it to effects such as sun, rain, snow, powder etc.
•Do not keep flammable materials close while the appliance is operating.
•Pay attention to the cables of the other electrical devices operating near the appliance, so as not to touch to hot points.
•The appliance is not intended to be operated by means of an external timer or separate remote control system.
•Do not hang towels, dishcloths or clothes from the appliance or its handles.
•This manual is prepared for more than one model in common. Your appliance may not have some of the features that is explained in manual. Pay attention to the expressions that have figures, while you are reading the operating manual.
Safety when Cleaning and Maintenance
•Turn the appliance off before the operations such as cleaning or maintenance. You can do it after plugging the appliance off or turning the main switches off.
•! WARNING: Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock.
•Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.
•Every care is taken to ensure the safety of the customer. Glass can break, be carefull when cleaning the glass as not to scratch it. Do not knock or hit the glass with the accessories.
Children Safety
•! CAUTION: Accesible parts may be hot when the grill is in use. Young children should be
kept away. Keep children away from the oven.
•While the front door is open, do not let climb on the door or sit on it.
•Children should be supervised to ensure that they do not play with the appliance.
FOR EFFICIENCY AND SAFETY OF APPLIANCE, WE RECOMMEND YOU ALWAYS TO USE THE ORIGINAL SPARE PARTS AND TO CALL ONLY OUR AUTHORIZED SERVICES IN CASE OF NEED.
•Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present.
6
3. INSTALLATION AND PREPARATIONS FOR USE
This modern, functional and practical cooker, that was manufactured with the parts and materials of highest quality, will meet your cooking needs in every aspect. You must surely read this manual so that you don't have any problem in future and to be able to have satisfactory results. The following information are the required rules for right installation and service processes. It must be read especially by the technician who will install the appliance.
!Contact to Authorized Service for installation of your product
3.1Environment where your appliance will be installed
•Your product must be set up and used in a place where it will always have ventilation.
•While operating, this appliance needs 2m3/h air per kw input.
•There must be a natural ventilation enough to provide the gas to be used in the environment. The average air flow must directly come in through the air holes that will be opened on the walls that are opened towards outside.
Air inlet section |
min. 100cm2 |
Figure 1
Air inlet section min. 100cm2
Figure 2
•These air holes must have at least the effective cross section of 100cm2 for fresh air circulation (One or more air holes can be opened.). This hole (or holes) must be opened so that they are not blocked. Preferably they must be placed close to the bottom and at opposite side of the smokes of the burned gases that were emptied. If it seems not possible to open these ventilations in the place where the appliance is set up, the needed air can also be obtained through the next room, provided that this place is not a bedroom or a dangerous place. In this case this “next room” must also be ventilated as required.
Emptying of the Burned Gases from Environment
The cooking appliances that operate with gas, throw the burned gas wastes out directly to the outside or through the cooker hoods that are connected to the a chimney that opens directly to the outside. If it seems not possible to install a cooker hood, it is required to set an electric fan on the window or wall that has access to fresh air. This electric fan must have the capacity to change the air of the kitchen environment 4-5 times of its own volume of air per hour.
7
3. INSTALLATION AND PREPARATIONS FOR USE
Cooker hood |
|
flue |
Electrical ventilator |
|
|
Air inlet section |
|
|
|
|
Air inlet section |
|||||||||
|
|
2 |
||||||||||||||
2 |
||||||||||||||||
|
|
|
|
|
min. 100cm |
|||||||||||
|
|
|
|
min. 100cm |
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 3 |
|
|
|
|
|
|
|
Figure 4 |
||||||
|
|
|
||||||||||||||
|
|
|
|
|
Min. 60cm |
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
COOKER HOOD |
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Min.65cm(with hood) |
|
Min. 70cm(without hood) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
Min. 42cm |
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
Min. 42cm |
|
|
|
|||||
|
|
|
|
|
|
|
|
|
||||||||
Figure 5
3.2 Installation of product
There are some factors that must be paid attention to while installing your product. Surely be very careful to while installing your product. Pay attention to our below instructions in order to be able to prevent any problems and/or dangerous situations that may occur later.
•The appliance can be placed close to other furniture on condition that in the area where the oven is set up, the furniture's height does not exceed the height of the cooker panel.
•Pay attention not to place it near the refrigerator, there must be no flammable or inflammable materials such as curtain, waterproof cloth, etc. that will begin to burn quickly.
•It is required that there must be least a 2cm blank space around the product for air circulation.
•The furniture close to product must be manufactured resistant to temperatures up to 80°C.
•If the kitchen furniture are higher than the cooktop, it must be at least 10cm away from the cooker's side.
The minimum heights from the pan support and wall cupboards to cooker hoods with fan over the product, are shown in figure 5. Thus, the cooker hood must be at minimum 65cm height from the pan support. If there is no cooker hood, this height must not be less than 70cm.
8
3.INSTALLATION AND PREPARATIONS FOR USE
3.3Adjustment of feet
Your product stands on 4 adjustable feet. When the product is placed where to be used, check if the product is balanced. If it is not balanced, you can make the adjustment by turning the feet clockwise if required. It is possible to raise the appliance maximum 30mm by the feet. If the feet are adjusted appropriately, it is required not to move the appliance by dragging, it should be moved by lifting it up.
Figure 6
3.4 Gas connection
Assembly of gas supply and leakage check
The connection of the appliance should be performed in accordance with local and international standards and regulations applicable. You can find the information related to appropriate gas types and appropriate gas injectors on technical data table. If the pressure of used gas is different than these values stated or not stable in your area, it may be required to assemble an available pressure regulator on the gas inlet. It is certainly required to contact to the authorized service to make these adjusments.
The points that must be checked during flexible hose assembly
If the gas connection is made by a flexible hose that is fixed on the gas inlet of appliance, it must be fixed by a pipe collar as well. Connect your appliance with a short and durable hose that is as close as possible to the gas source. The hose's permitted maximum lenght is 1.5m. The hose that brings gas to the appliance must be changed once a year for your safety.
The hose must be kept clear from areas that may heat up to temperatures in excess of 500C. The hose must not be ruptured, bent or folded. It must be kept clear of sharp corners, moving things, and should not be defective. Before assembly, it must be checked whether there is any production defect.
As gas is turned on, all connection parts and hose must be checked with soapy water or leakage fluids. Do not use naked flame to check gas leakage. All metal components used during gas connection must be clear of rust. Also check the expiry dates of components to be used.
The points that must be checked during fixed gas connection assembly
To assemble a fixed gas connection (gas connection made by threads, e.g. a nut), there are different methods used in different countries. The most common parts are already supplied with your appliance. Any other part can be supplied as spare part.
During connections always keep the nut on the gas manifold fixed, while rotating the counter-part. Use spanners of appropriate size for safe connection. For all surfaces between different components,
9
3. INSTALLATION AND PREPARATIONS FOR USE
always use the seals provided in the gas conversion kit. The seals used during connection should also be approved to be used in gas connections. Do not use plumbing seals for gas connections.
Remember that this appliance is ready to be connected to gas supply in the country for which it has been produced. The main country of destination is marked on the rear cover of the appliance. If you need to use it in another country, any of the connections in the figure below can be required. In such a case, learn the appropriate connection parts and obtain those parts to perform a safe connection.
Gas Pipe |
Gas Pipe |
Gas Pipe |
Gas Pipe |
|
Seal |
Seal |
|
|
|
|
|
|
||
Hose |
Adapter |
Seal |
|
|
Fitting |
|
|
Mechanical |
|
|
Mechanical |
Mechanical |
||
Gas Hose |
Gas Hose |
|||
Gas Hose |
Gas Hose |
|||
with Collar |
|
|||
|
|
|
Figure 7
It is required to call the authorized service to be able to make the gas connections appropriately and in compliance with safety standards.
!ATTENTION! Surely do not use any match or lighter for control of gas leakage.
3.5 Electric connection and safety
During the electric connection, follow the instructions stated in the user manual.
•The earthing cable must be connected to the earth terminal.
•You have to ensure the power cord with suitable insulation to be connected to the power source during the connection. If there is no appropriate earthed electric outlet in accordance with regulations in the place where the appliance to be installed, contact to our authorized service. The earthed electric outlet must be close to the appliance.
•Do not use an extension cord.
•The power cord must not touch to the hot surface of the product.
•In case the cord is damaged, contact Authorized Service to have it changed.
•Any wrong electric connection may damage your appliance, as well as endangering your safety, rendering your guarantee invalid.
10
3.INSTALLATION AND PREPARATIONS FOR USE
•The appliance is adjusted for 230V 50Hz electricity. If the mains electricity is different contact your authorized service.
BROWN |
L |
N |
BLUE |
YELLOW+GREEN |
|
||
|
|
|
Figure 8
•The supply cord should be kept away from hot parts of appliance. Otherwise, the cord may be damaged, causing short circuit.
•The manufacturer declares that it has no responsibility against any kind of damages and losses that are caused by improper connections that are performed by unauthorized people.
3.6 Gas conversion
Caution : The following procedures must be undertaken by authorized service people.
Your appliance is adjusted to be operated with LPG gas. The gas burners can be adapted to different types of gas, by replacing the corresponding injectors and adjusting minimum flame length suitable to the gas in use. For this purpose, following steps should be performed:
Changing injectors:
Hob Burners:
•Cut off the main gas supply and unplug from the electric mains.
•Remove the burner cap and the adapter(Figure 9).
•Unscrew the injectors. For this, use a 7mm spanner(Figure 10).
•Replace the injector with the ones from the gas conversion kit, with corresponding diameters suitable to the type of gas that is going to be used, according to the information chart (which is also supplied in the gas conversion kit).
11
3. INSTALLATION AND PREPARATIONS FOR USE
Spanner
Injector
Figure 9 |
Figure 10 |
Oven/Grill Injectors:
The oven and grill injectors are assembled by a single screw that is placed on the tip of the burner. For grill burners, this screw is already visible(Figure 11). Remove the screw, pull the grill burner to yourself and you will see the injector revealed on the rear surface of the oven cavity (Figure 12).
For oven burners, open the drawer compartment and you will see the assembly screw below the burner (Figure 13). Remove the screw, move the burner diagonally and the injector will be revealed on the rear side of the burner box (Figure 12).
Remove the injectors with a 7mm spanner and replace the injector with the ones from the spare set, with corresponding diameters suitable to the type of gas that is going to be used, according to the information chart (which is also supplied in the gas conversion kit).
Screw |
Screw |
|
Injector
Figure 11 |
Figure 12 |
Figure 13 |
Adjusting the reduced flame position:
The flame length in the minimum position is adjusted with a flat screw located on the valve. For valves with flame failure device, the screw is located on the side of the valve spindle(Figure 14). For easier reduced flame adjustment, it is advised to remove the control panel (and microswitch, if present) during adjustment.
12
3. INSTALLATION AND PREPARATIONS FOR USE
To determine the minimum position, ignite the burners and leave them on in minimum position. Remove the with the help of a small screwdriver fasten or loosen the bypass screw around 90 angular degrees. When the flame has a length of at least 4mm, the gas is well distributed. Make sure that the flame does not die out when passing from the maximum position to the minimum position. Create an artificial wind with your hand toward the flame to see if the flames are stable.
Valve with flame failure device
Bypass Screw
Figure 14
For oven burner, operate the oven burner at minimum position for 5 minutes, then open and close the oven door for 2-3 times to check the flame stability of the burner.
Reduced flame position adjustment is not required for grill burners.
The position the bypass screw must be loosened for conversion from LPG. For conversion from LPG, the same screw must be fastened. Make sure that the appliance is unpluged from the electric mains and the gas supply is open.
Thermostatic oven valve
Bypass Screw |
Figure 15 |
|
Changing the gas inlet:
For some countries, the gas inlet type can be different for LPG gases. In such a case, remove the current connection components and nuts (if any) and connect the new gas supply accordingly. In all conditions, all components used in gas connections should be approved by local and/or international authorities. In all gas connections, refer to the “Assembly of gas supply and leakage check” clause explained before.
13
4.USE OF YOUR PRODUCT
4.1Use of gas burners
Ignition of the burners
To determine which knob controls which burner, check the position symbol above the knob.
•Manual Ignition of the Gas Burners
If your appliance is not equipped with any ignition aid or in case there is a failure in the electric network, follow the procedures listed below:
For Hob Burners: To ignite one of the burners, press and turn its knob counter-clockwise so that the knob is in maximum position, approach a match, taper or another manual aid to its upper circumference. Move the ignition source away as soon as you see a stable flame.
For Oven Burner: To ignite the oven burner, press and turn the oven control knob counter-clockwise so that the knob is in maximum position, approach a match, taper or another manual aid to the ignition hole that is located on the front left corner of the burner. Move the ignition source away as soon as you see a stable flame.
For Grill Burner: To ignite the grill burner, turn the grill valve in the clockwise position until the marker on the knob points at the grill sign. Then, keep the knob pressed and approach a match, taper or another manual aid to the holes that are situated on the burner. Move the ignition source away as soon as you see a stable flame.
•Electrical Ignition
Electrical ignition of gas burners can be done in two ways; depending on the configuration of your appliance.
Ignition by Spark Button: Press the valve of the burner you want to operate and turn the valve in the counter-clockwise direction so that the knob is in maximum position and with your other hand, press the ignition button (Figure 16) at the same time. Press the ignition button immediately, because if you wait, a build up of gas may cause the flame to spread. Continue pressing the ignition button until you see a stable flame
on the burner.
Figure 16
Ignition Through Hob Valve (micro switch): Press the valve of the burner you want to operate and turn the valve in the counterclockwise direction (clockwise for the grill burner) so that the knob is in maximum position while keeping the knob pressed. The spark plugs will generate sparks as long as you keep the control knob pressed. The micro switch placed under the knob will automatically create sparks through the spark plug of the burner. Continue pressing the knob until you see a stable flame on the burner.
14
4. USE OF YOUR PRODUCT
Flame safety device:
Hob Burners (If your hob is equipped with gas safety device)
Hobs equipped with flame failure device provide security in case of accidentally extinguished flame. If such a case occurs, the device will block the burners gas lines and will avoid any accumulation
of unburned gas. Wait 90 seconds before re-igniting an extinguished gas burner.
Oven / Grill Burners
Regardless of the model of your appliance, all oven burners are equipped with a gas safety device. For this reason, during ignition, keep the oven knob pressed until you see stable flames. If the flames are cut out after you release the knob, repeat the procedure again. If the oven burner does not ignite after you keep the burner knob pressed for 30 seconds, open the oven door and do not attempt re-ignition for at least 90 seconds. When oven flames go out accidentally, repeat the same procedure.
4.1.1 Control of the hob burners
OFF position |
MAX. position |
MIN. position |
MODULATE |
Figure 17
The knob has 3 positions: Off (0), maximum (big flame symbol) and minimum (small flame symbol). After you ignite the burner in maximum position; you can adjust the flame length between maximum and min. positions. Do not operate the burners when the knob position is between maximum and off positions.
Cap
Crown
Spark
Plug
Burner
Cup
Figure 18
After the ignition, check the flames visually. If you see yellow tip, lifted or unstable flames; turn the gas flow off, and check the assembly of burner caps and crowns (Figure 20). Also, make sure that no liquid has flown into the burner cups. If the burner flame goes out accidentally, turn the burner off, ventilate the kitchen with fresh air, and do not attempt reignition for 90 sec.
When turning the hob off, turn the knob in the clockwise direction so that the knob shows "0" position or the marker on the knob points upwards.
15
4. USE OF YOUR PRODUCT
Your hob has burners of different diameters. The most economic way of using gas is to choose the correct size gas burners for your cooking pan size and to bring the flame to minimum position once the boiling point is reached. It is recommended to always cover your cooking pan.
In order to obtain maximum performance from the main burners, use pots with the following flat bottom diameters. Using smaller pots than the minimum dimensions stated below will cause energy loss.
Rapid Burner: 22-26cm Semi-rapid Burner: 14-22cm Auxiliary Burner: 12-18cm
Make sure that the tips of the flames do not spread out of the outer circumference of the pan, as this may also harm the plastic accessories around the pan (handles etc.).
Figure 19
When the burners are not in use for prolonged periods, always turn the main gas control valve off.
!WARNING:
•Use only flat pans and with a sufficiently thick base.
•Ensure that the base of the pan is dry before placing it on the burners.
•The temperature of accessible parts may be high when the appliance is operating. So it is imperative to keep children and animals out of the reach of the burners during and after cooking.
•After use, the hob remains very hot for a prolonged period of time, do not touch it and do not place any object on top of the hob.
•Never place knives, forks, spoons and lids on the hob as they will get hot and could cause serious burns.
16
Loading...