Nordmende CTG50BK, CTG50LPGBK User Manual [de]

CTG50LPGBK

CTG50BK

OPERATING AND INSTALLATION

INSTRUCTIONS OF

FREESTANDING

GAS DOUBLE OVEN

Dear Customer,

Our goal is to offer you products with high quality that exceed your expectations. Your appliance is produced in modern facilities carefully and particularly tested for quality.

This manual is prepared in order to help you use your appliance that is manufactured by the most recent technology, with confidence and maximum efficiency.

Before using your appliance, carefully read this guide that includes the basic information for right and safe installation, maintenance and use please contact to the nearest Authorized Service for the installation of your product.

CE Declaration of conformity

This appliance has been designed to be used only for cooking. Any other use (such as heating a room) is improper and dangerous.

This appliance has been designed, constructed, and marketed incompliance with:

• Safety requirements of the "Gas" Directive 2009/142/EC;

• Safety requirements of the "Low voltage" Directive 2006/95/EC;

• Safety requirements of the "EMC" Directive 2004/108/EC;

• Requirements of the Directive 93/68/EC.

CONTENTS:

1. Part : PRESENTATION AND SIZES OF PRODUCT

2. Part : WARNINGS

3. Part : INSTALLATION AND PREPARATIONS FOR USE

3.1 Environment where the appliance will be installed

3.2 Installation of oven

3.3 Adjustment of feet

3.4 Gas connection

3.5 Electric connection and security

3.6 General warnings and measures

3.7 Gas conversions

4. Part : USE OF YOUR OVEN

4.1 Use of gas burners

4.1.1 Control of hob burners

4.1.2 Control of oven burner

4.1.3 Control of grill burner

4.2 Accessories used in oven

5. Part : CLEANING AND MAINTENANCE

5.1 Cleaning

5.2 Maintenance

6. Part : SERVICE AND TRANSPORT

6.1

Basic troubleshooting before contacting service

6.2 Information related to the transport

1. Part : PRESENTATION AND SIZES OF PRODUCT

PRESENTATION:

2.Rack

1.Rack

List of Components:

1- Cooktop 2- Control Panel 3- Oven Door Handle 4- Supply Leg 5- Oven Door 6- Oven Tray 7- Wire Grid 8- Grill 9- Oven Lamp 10- Semi-Rapid Burner 11- Rapid Burner 12- Auxillary Burner 13- Hob Grids 14- Semi-Rapid Burner

5.Rack

4.Rack

3.Rack

2.Rack

1.Rack

MODEL

CTG50LPGBK

CTG50BK

SIZE (mm)

50 * 60 * 90

2. Part : WARNINGS

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE USING YOUR

APPLIANCE, AND KEEP IT IN A CONVENIENT PLACE FOR REFERENCE WHEN NECESSARY.

THIS MANUAL IS PREPARED FOR MORE THAN ONE MODEL IN COMMON. YOUR APPLIANCE

MAY NOT HAVE SOME OF THE FEATURES THAT ARE EXPLAINED IN THIS MANUAL. PAY

ATTENTION TO THE EXPRESSIONS THAT HAVE FIGURES, WHILE YOU ARE READING THE

General Safety Warnings

OPERATING MANUAL.

- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

- WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.

- WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

- WARNING: Danger of fire: do not store items on the cooking surfaces.

2. Part : WARNINGS

- WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.

- For hobs incorporating a lid, any spillage should be removed from the lid before opening. And also the hob surface should be allowed to cool before closing the lid.

- The appliance is not intended to be operated by means of an external timer or separate remote-control system.

- WARNING: In order to prevent tipping of the appliance, the stabilizing brackets must be installed. (For detail information please read the anti-tilting kit set guide.)

- During use, the appliance becomes hot. Care should be taken to avoid touching heating elements inside the oven.

- During use, handles held for short periods in normal use can get hot.

- Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass and other surface since they can scratch the surface, which may result in shattering of the glass or damage to the surface.

- Do not use steam cleaners for cleaning the appliance.

2. Part : WARNINGS

- WARNING: Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock.

- CAUTION: Accessible parts may be hot when the cooking or grilling is in use. Young children should be kept away.

• Your appliance is produced in accordance with all applicable local and international standards and regulations.

• Maintenance and repair work must be made only by authorized service technicians. Installation and repair work that is carried out by unauthorized technicians may endanger you. It is dangerous to alter or modify the specifications of the appliance in any way.

• Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure or electricity voltage and frequency) and the requirements of the appliance are compatible. The requirements for this appliance are stated on the label.

• CAUTION: This appliance is designed only for cooking food and is intended for indoor domestic household use only and should not be used for any other purpose or in any other application, such as for non-domestic use or in a commercial environment or room heating.

• Do not try to lift or move the appliance by pulling the door handle.

• This appliance is not connected to a combustion products evacuation device. It shall be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation.

• If after 15 s the burner has not lit, stop operating the device and open the compartment door and/or wait at least 1 min before attempting a further ignition of the burner.

• These instructions are only valid if the country symbol appears on the appliance. If the symbol does not appear on the appliance, it is necessary to refer to the technical instructions which will provide the necessary instructions concerning modification of the appliance to the conditions of use of the country.

• All possible security measures have been taken to ensure your safety. Since the glass may break, you should be careful while cleaning to avoid scratching. Avoid hitting or knocking on the glass with accessories.

• Ensure that the supply cord is not wedged during the installation. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to prevent a hazard.

• While the oven door is open, do not let children climb on the door or sit on it.

Installation Warnings

• Do not operate the appliance before it is fully installed.

• The appliance must be installed by an authorized technician and put into use. The producer is not responsible for any damage that might be caused by defective placement and installation by unauthorized people.

• When you unpack the appliance, make sure that it is not damaged during transportation. In case of any defect; do not use the appliance and contact a qualified service agent immediately. As the materials used for packaging (nylon, staplers, styrofoam...etc) may cause harmful effects to children, they should be collected and removed immediately.

• Protect your appliance against atmospheric effects. Do not expose it to effects such as sun, rain, snow etc.

• The surrounding materials of the appliance (cabinet) must be able to withstand a temperature of min 100°C.

2. Part : WARNINGS

During usage

• When you first run your oven a certain smell will emanate from the insulation materials and the heater elements. For this reason, before using your oven, run it empty at maximum temperature for 45 minutes. At the same time you need to properly ventilate the environment in which the product is installed.

• During usage, the outer and inner surfaces of the oven get hot. While opening the oven door, step back to avoid the hot steam coming out of the oven. There may be a risk of burns.

• Do not put flammable or combustible materials, in or near the appliance when it is operating.

• Always use oven gloves to remove and replace food in the oven.

• Do not leave the cooker while cooking with solid or liquid oils. They may catch fire on condition of extreme heating. Never pour water on to flames that are caused by oil. Cover the saucepan or frying pan with its cover in order to choke the flame that has occurred in this case and turn the cooker off.

• Always position pans over the centre of the cooking zone, and turn the handles to a safe position so they cannot be knocked or grabbed.

• If you will not use the appliance for a long time, plug it off. Keep the main control switch off. Also when you do not use the appliance, keep the gas valve off.

• Make sure the appliance control knobs are always in the "0" (stop) position when it is not used.

• The trays incline when pulled out. Be careful not to let hot liquid spill over.

• CAUTION: The use of a gas cooking appliance results in the production of heat, moisture and products of combustion in the room in which it is installed. Ensure that the kitchen is well ventilated especially when the appliance is in use, keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood).

• Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present.

• While using the grill burner, keep the oven door open and always use the grill deflector shield supplied with the product. Never use the grill burner with the oven door closed.

• CAUTION: Glass lids may shatter when heated. Turn off all the burners before shutting the lid. The hob surface should be allowed to cool before closing the lid.

• When the door or drawer of the oven is open, do not leave anything on it. You may unbalance your appliance or break the cover.

• Do not put heavy things or flammable or ignitable goods (nylon, plastic bag, paper, cloth...etc) into the drawer. This includes cookware with plastic accessories (e.g. handles).

• Do not hang towels, dishcloths or clothes from the appliance or its handles.

During cleaning and maintenance

• Always turn the appliance off before operations such as cleaning or maintenance. You can do it after plugging the appliance off or turning the main switches off.

• Do not remove the control knobs to clean the control panel.

TO MAINTAIN THE EFFICIENCY AND SAFETY OF YOUR APPLIANCE, WE RECOMMEND YOU

ALWAYS USE ORIGINAL SPARE PARTS AND TO CALL ONLY OUR AUTHORIZED

SERVICE AGENTS IN CASE OF NEED.

3. Part : INSTALLATION AND PREPARATIONS FOR USE

This modern, functional and practical oven, that was manufactured with the parts and materials of highest quality, will meet your cooking needs in every aspect. You must surely read this manual so that you don't have any problem in future and to be able to have satisfactory results. The following information are the required rules for right installation and service processes. It must be read especially by the technician who will install the appliance

Contact To Authorized Service For Installation Of Your Oven

3.1 Environment where your appliance will be installed

•

Your oven must be set up and used in a place where it will always have ventilation

• 2m /h air per kw input.

While operating, this appliance needs

•

There must be a natural ventilation enough to provide the gas to be used in

the environment. The average air flow must directly come in through the air holes that will be opened on the walls that are opened towards outside.

Air inlet section min. 100cm

Figure 1

These air holes must have at least the effective cross section of 100cm for

Air inlet section min. 100cm

Figure 2

fresh air circulation (One or more air holes can be opened.). This hole (or holes) must be opened so that they are not blocked. Preferably they must be placed close to the bottom and at opposite side of the smokes of the burned gases that were emptied. If it seems not possible to open these ventilations in the place where the appliance is set up, the needed air can also be obtained through the next room, provided that this place is not a bed room or a dangerous place. In this case this “next room” must also be ventilated as required.

Emptying of the Burned Gases from Environment

The cooking appliances that operate with gas, throw the burned gas wastes out directly to the outside or through the cooker hoods that are connected to the a chimney that opens directly to the outside. If it seems not possible to install a cooker hood, it is required to set an electric fan on the window or wall that has

3. Part : INSTALLATION AND PREPARATIONS FOR USE

access to fresh air. This electric fan must have the capacity to change the air of the kitchen environment 4-5 times of its own volume of air per hour.

Cooker hood flue

Electrical ventilator

Air inlet section min. 100cm

Min. 42cm

Air inlet section min. 100cm

Figure 3 Figure 4

Min. 60cm

COOKER HOOD

Min. 70cm(without hood)

Min. 65cm(with hood)

Min. 42cm

Figure 5

3.2 Installation of oven

There are some factors that must be paid attention to while installing your oven. Surely be very careful to while installing your oven. Pay attention to our below instructions in order to be able to prevent any problems and/or dangerous situations that may occur later

•

The appliance can be placed close to other furniture on condition that in the

area where the oven is set up, the furniture's height does not exceed the height of the cooker panel

3. Part : INSTALLATION AND PREPARATIONS FOR USE

Pay attention not to place it near the refrigerator, there must be no

•

flammable or inflammable materials such as curtain, waterproof cloth, etc. that will begin to burn quickly

It is required that there must be least a 2cm blank space around the oven for

•

air circulation

If the kitchen furniture are higher than the hob plate of the oven, it must be

•

at least 10cm away from the oven's side.

The minimum heights from the oven's pan and wall cupboards and cooker hoods with fan over the oven, are shown as above. Thus, the cooker hood must be at minimum 65cm height from the cooker pan. If there is no cooker hood, this height must not be less than 70cm.

3.3 Adjustment of feet

Your oven stands on 4 adjustable feet. When the oven is placed where it will be used, check if the oven is balanced. If it is not balanced, you can make the adjustment by turning the feet clockwise if required. It is possible to raise the appliance maximum 30mm by the feet. If the feet are adjusted appropriately, it is required not to move the appliance by dragging, it should be moved by lifting it up

3.4 Gas connection

The connection of the appliance should be performed in accordance with local and international standards and regulations applicable. You can find the information related to appropriate gas types and appropriate gas injectors on technical data table. If the pressure of used gas is different than these values stated of the or not stable in your area, it may be required to assemble an available pressure regulator on the gas inlet. It is certainly required to contact to the authorized service to make these adjustments.

The points that must be checked during flexible hose assembly

If the gas connection is made by a flexible hose that is fixed on the gas inlet of appliance, it must be fixed by a pipe collar as well. Connect your appliance with a short and durable hose that is as close as possible to the gas source. The hose's permitted maximum length is 1.5m. The hose that brings gas to the appliance must be changed once a year for your security.

The hose must be kept clear from areas that may heat up to temperatures in excess of 50 C. The hose must not be ruptured, bent or folded. The hose must

be kept clear of sharp corners, moving things, and should not be defective. Before assembly, it must be checked whether there is any production defect.

3. Part : INSTALLATION AND PREPARATIONS FOR USE

As gas is turned on, all connection parts and hose must be checked with soapy water or leakage fluids. Do not use naked flame to check gas leakage. All metal components used during gas connection must be clear of rust. Also check the expiry dates of components used.

The points that must be checked during Fixed gas connection assembly

To assemble a fixed gas connection (gas connection made by threads, e.g. a nut), there are different methods used in different areas. The most common parts are already supplied with your appliance. Any other part can be supplied as spare part.

During connections always keep the nut on the gas manifold fixed, while rotating the counter-part. Use spanners of appropriate size for safe connection. For all surfaces between different components, always use the seals provided in the spare set. The seals used during connection should also be approved to be used in gas connections. Do not use plumbing seals for gas connections.

Remember that this appliance is prepare to be connected to gas supply in the country for which it has been produced. The main country of destination is marked on the rear cover of the appliance. If you need to use it in another country, any of the connections in the figure below can be required. In such a case, learn the appropriate connection parts and obtain those parts to perform a safe connection.

Gas Pipe Gas Pipe Gas Pipe Gas Pipe

Seal

Hose Fitting

Gas Hose with Collar

Seal

Adapter

Mechanical Gas Hose

Seal

Mechanical Gas Hose

It is required to call the authorized service to be able to make the gas connections appropriately and in compliance with safety standards..

ATTENTION! leakage

Surely do not use any match and lighter for control of gas

Figure 6

3. Part : INSTALLATION AND PREPARATIONS FOR USE

3.5 Electric connection and security

During the electric connection, follow the instructions stated in the user manual

• .

•

• .

•

• .

•

The earthing cable must be connected to the earth terminal You have to ensure the power cord with suitable insulation to be connected

to the power source during the connection If there is no appropriate earthed

. electric outlet in accordance with regulations in the place where the appliance will be installed, immediately contact to our authorized service. The earthed electric outlet must be close to the appliance.

Do not use an extension cord The power cord must not touch to the hot surface of the product. In case the cord is damaged, contact Authorized Service to have it changed Any wrong electric connection may damage your appliance, as well as

endangering your safety, rendering your guarantee invalid

The appliance is adjusted for 230V 50Hz electricity. If the network electricity is different than this value, immediately contact your authorized service

BROWN

YELLOW+GREEN

Figure 7

The supply cord should be kept away from hot parts of appliance. Otherwise

•

BLUE

the cord may be damaged, causing short circuit. The producer firm declares that it has no responsibility against any kind of

•

damages and losses that are caused by improper connections that are performed by unauthorized people

3. Part : INSTALLATION AND PREPARATIONS FOR USE

3.6 General warnings and measures

Your appliance is produced in accordance with the local and international

•

standards and regulations applicable.

The maintenance and repair works must be made only by authorized service

•

technicians. The installation and repair works without following proper knowledge may endanger you

While your appliance operates, its outside surfaces heat up. The interior

•

surfaces of oven, and the flue outlets are quite hot. Even if the appliance is turned off, these parts keep its heat for a specific time. Do not touch onto hot surfaces, and keep children away

Do not leave the cooker while cooking with solid or liquid oils. They may

•

catch fire on condition of extreme heating. Never pour water to the flames that are caused by oil. Cover the saucepan or frying pan with its cover in order to choke the flame that has occurred in this case and turn the cooker off

The oven and heat adjustment switches must be adjusted for cooking in your

•

oven. Otherwise the oven does not operate.

When the door or drawer of oven is open do not leave anything on it . You

•

may unbalance your appliance or break the cover

Do not put heavy things or flammable or ignitable goods (nylon, plastic

•

bag,paper,cloth...etc) into the lower drawer. This includes cookware with plastic accessories (e.g. handles).

Plug the appliance off the electrical network when you do not use the

•

appliance and keep the gas valve off.

Protect your appliance against atmospheric effects. Do not leave it to effects

•

such as sun, rain, snow, powder etc.

Remember that this appliance is designed for indoor use.

•

3.7 Gas conversions

Caution : The following procedures must be undertaken by authorized service personnel.

Your appliance is adjusted to be operated with NG/LPG gas. The gas burners can be adapted to different types of gas, by replacing the corresponding injectors and adjusting minimum flame length suitable to the gas in use. For this purpose, following steps should be performed

3. Part : INSTALLATION AND PREPARATIONS FOR USE

Figure 8

Figure 9

Figure 10

3. Part : INSTALLATION AND PREPARATIONS FOR USE

Figure 11

Adjusting The Reduced Flame Position

The flame length in the minimum position is adjusted with a flat screw located on the valve. For valves with FFD, the screw is located on the side of the valve spindle. For valves without FFD, the screw is located inside the valve spindle. For easier reduced flame adjustment, we advise to remove the control panel (and microswitch, if present) during adjustment.The position the by pass screw must be loosened in transformation from LPG to NG. In transformation from NG to LPG, the same screw must be fastened. Make sure that the appliance is unplugged from the electric current and the gas feed is open.

To determine the min. position, ignite the burners and leave them on in minimum position. Remove the knobs because the screws are accessible only when the knobs are removed. With the help of a small screwdriver fasten or loosen the by pass screw around 90 degrees. When the flame has a length of at least 4mm, the gas is well distributed. Make sure that the flame does not die out when passing from the maximum position to the minimum position. Create an artificial wind with your hand toward the flame to see if the flames are stable. For oven burner, operate the oven burner at min. position for 5 minutes, then open and close the oven door for 2-3 times to check the flame stability of the burner.

Changing the gas inlet:

For some countries, the gas inlet type can be different for NG/LPG gases. In such a case, remove the current connection components and nuts (if any) and connect the new gas supply accordingly. In all conditions, all components used in gas connections should be approved by local and/or international authorities. In all gas connections, refer to the “ASSEMBLY OF GAS SUPPLY AND LEAKAGE CHECK” clause explained before.

3. Part : INSTALLATION AND PREPARATIONS FOR USE

Adjusting the reduced flame position

The flame length in the minimum position is adjusted with a flat screw located on the valve. For valves with flame failure device, the screw is located on the side of the valve spindle(Figure 14). For easier reduced flame adjustment, it is advised to remove the control panel (and microswitch, if present) during adjustment. To determine the minimum position, ignite the burners and leave them on in minimum position. Remove the with the help of a small screwdriver fasten or loosen the bypass screw around 90 angular degrees. When the flame has a length of at least 4mm, the gas is well distributed. Make sure that the flame does not die out when passing from the maximum position to the minimum position. Create an artificial wind with your hand toward the flame to see if the flames are stable.

Valve with flame failure device

Bypass Screw

Figure 14

For oven burner, operate the oven burner at minimum position for 5 minutes, then open and close the oven door for 2-3 times to check the flame stability of the burner.

Reduced flame position adjustment is not required for grill burners. The position the bypass screw must be loosened for conversion from LPG to NG.

For conversion from NG to LPG, the same screw must be fastened. Make sure that the appliance is unplugged from the electric mains and the gas supply is open.

Thermostatic oven valve

Bypass Screw

Figure 16

4. Part : USE OF YOUR OVEN

4.1 Use of gas burners

Ignition of the burners

To determine which knob controls which burner, check the position symbol above the knob.

Manual Ignition of the Gas Burners

•

If your appliance is not equipped with any ignition aid or in case there is a failure in the electricity network, follow the procedures listed below

For Hob Burners: To ignite one of the burners, press and turn its knob counter-clockwise so that the knob is in max. position, approach a match, taper or another manual aid to its upper circumference. Move the ignition source away as soon as you see a stable flame.

For Oven Burners: To ignite the oven burner, press and turn the oven control knob counter-clockwise so that the knob is in max. position, approach a match, taper or another manual aid to the ignition hole that is located on the front left corner of the burner. Move the ignition source away as soon as you see a stable flame.

For Grill Burners: To ignite the grill burner, turn the grill valve in the clockwise position until the marker on the knob points at the grill sign. Then, keep the knob pressed and approach a match, taper or another manual aid to the holes that are situated on the burner. Move the ignition source away as soon as you see a stable flame.

Electrical Ignition

•

Electrical ignition of gas burners can be done in two ways; depending on the configuration of your appliance

Ignition by Spark Button: Press the valve of the burner you want to operate and turn the valve in the counter-clockwise direction so that the knob is in max. position and with your other hand, press the ignition button at the same time. Press the ignition button immediately, because if you wait, a build up of gas may cause the flame to spread. Continue pressing the ignition button until you see a stable flame on the burner.

Ignition Through Hob Valve (micro switch): Press the valve of the burner you want to operate and turn the valve in the counter clockwise direction (clockwise for the grill burner) so that the knob is in max. position while keeping the knob pressed. The spark plugs will generate sparks as long as you keep the control knob pressed. The micro switch placed under the knob will automatically create sparks through the spark plug of the burner. Continue

+ 41 hidden pages