www.nordictrack.com
Model No. NTL19010.0
Serial No.
Write the serial number in the space
above for reference.
Serial
Number
Decal
QUESTIONS?
If you have questions, or if parts
are damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
USER’S MANUAL
CALL TOLL-FREE:
1-800-TO-BE-FIT
(1-800-862-3348)
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.nordictrackservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS .................................................................3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
THE CHEST HEART RATE MONITOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
OPERATION AND ADJUSTMENT ............................................................14
HOW TO MOVE THE INCLINE TRAINER ......................................................27
TROUBLESHOOTING .....................................................................28
EXERCISE GUIDELINES ...................................................................31
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the warning
decals. If a decal is missing or illegible, call the
telephone number on the front cover of this
manual and request a free replacement decal.
Apply the decal in the location shown. Note: The
decals may not be shown at actual size.
NORDICTRACK is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precations and in-
structions in this manual and all warnings on your incline trainer before using your incline trainer.
ICON assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with
pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this incline trainer are adequately informed of all warnings and
precautions.
3. Use the incline trainer only as described.
4. Keep the incline trainer indoors, away from
moisture and dust. Do not put the incline
trainer in a garage or covered patio, or near
water.
5. Place the incline trainer on a level surface,
with at least 8 ft. (2.4 m) of clearance behind
it and 2 ft. (0.6 m) on each side. Do not place
the incline trainer on any surface that blocks
air openings. To protect the oor or carpet
from damage, place a mat under the incline
trainer.
6. Do not operate the incline trainer where
aerosol products are used or where oxygen
is being administered.
7. Keep children under age 12 and pets away
from the incline trainer at all times.
8. The incline trainer should be used only by
persons weighing 350 lbs. (159 kg) or less.
9. Never allow more than one person on the
incline trainer at a time.
11. When connecting the power cord (see page
14), plug the power cord into a surge suppressor (not included) and plug the surge
suppressor into a grounded circuit capable
of carrying 15 or more amps. No other appliance should be on the same circuit. Do not
use an extension cord.
12. Use only a single-outlet surge suppressor
that meets all of the specications described
on page 14. To purchase a surge suppressor,
see your local NORDICTRACK dealer or call
the telephone number on the front cover of
this manual and order part number 146148,
or see your local electronics store.
13. Failure to use a properly-functioning surge
suppressor could result in damage to the
control system of the incline trainer. If the
control system is damaged, the walking belt
may slow, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
14. Keep the power cord and the surge suppressor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the incline
trainer if the power cord or plug is damaged,
or if the incline trainer is not working properly. (See TROUBLESHOOTING on page 28 if
the incline trainer is not working properly.)
16. Read, understand, and test the emergency
stop procedure before using the incline trainer
(see HOW TO TURN ON THE POWER on page
16).
10. Wear appropriate exercise clothes while
using the incline trainer. Do not wear loose
clothes that could become caught in the
incline trainer. Athletic support clothes are
recommended for both men and women.
Always wear athletic shoes. Never use the
incline trainer with bare feet, wearing only
stockings, or in sandals.
17. Never start the incline trainer while you are
standing on the walking belt. Always hold the
handrails while using the incline trainer.
18. The incline trainer is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
3
19. The heart rate monitor is not a medical
device. Various factors, including the user’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is intended only as an exercise aid in determining
heart rate trends in general.
20. Never leave the incline trainer unattended
while it is running. Always remove the key,
unplug the power cord, and press the power
switch into the off position when the incline
trainer is not in use. (See the drawing on
page 5 for the location of the power switch.)
24. Inspect and properly tighten all parts of the
incline trainer regularly.
25. DANGER: Always unplug the power
cord immediately after use, before cleaning
the incline trainer, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing other than the procedures in this manual
should be performed by an authorized service representative only.
21. Do not attempt to move the incline trainer until it is properly assembled. (See ASSEMBLY
on page 7, and HOW TO MOVE THE INCLINE
TRAINER on page 27.) You must be able to
safely lift 45 lbs. (20 kg) to raise, lower, or
move the incline trainer.
22. When moving the incline trainer, make sure
that the storage latch is holding the frame
securely in the storage position.
23. Never insert any object into any opening on
the incline trainer.
SAVE THESE INSTRUCTIONS
26. This incline trainer is intended for home use
only. Do not use this incline trainer in a commercial, rental, or institutional setting.
27. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary
NORDICTRACK® INCLINE TRAINER X9i
INTERACTIVE. The INCLINE TRAINER X9i
INTERACTIVE offers a selection of features designed
to make your workouts at home more enjoyable and
effective.
For your benet, read this manual carefully before
using the incline trainer. If you have questions after
Heart Rate Monitor
Accessory Tray
Handrail
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number is shown on the front cover of this manual. The location of the serial number decal is shown
below.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Fan
Key/Clip
Walking Belt
Walking Platform
Length: 5 ft. 9 in. (175 cm)
Width: 3 ft. 1 in. (94 cm)
Idler Roller
Adjustment Screws
Wheel
Platform Cushion
Power Cord
Power Switch
5
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat-
tached. Extra hardware may be included.
5/16" Star
Washer (9)–4
#8 x 3/4"
Machine Screw
(16)–9
3/8" Star
Washer (8)–10
5/16" x 5/8"
Screw (11)–4
3/8" x 2 3/4" Screw (17)–2
3/8" x 5 1/2" Screw (5)–8
#8 x 3/4"
Screw (1)–8
5/16" x 2 1/2" Screw (4)–4
#8 x 1 1/4"
Screw (36)–2
6
ASSEMBLY
• Assembly requires two persons.
• Placeallpartsinaclearedareaandremovethe
packing materials. Do not dispose of the packing
materialsuntilyounishallassemblysteps.
• Theundersideofthewalkingbeltiscoatedwith
high-performance lubricant. After shipping, there
may be some lubricant on top of the walking belt
or on the shipping carton. This is normal. If there
is lubricant on top of the walking belt, wipe it off
with a soft cloth and a mild, non-abrasive cleaner.
1. Make sure that the power cord is unplugged.
Identify the right Upright (77), which has a wire
tie in it. Hold the Upright near the right side of
the incline trainer.
See the inset drawing. Tie the wire tie in the
right Upright (77) around the end of the Upright
Wire (78). Then, pull the other end of the wire tie
until the Upright Wire is routed out of the top of
the Upright.
• To identify small parts, see page 6.
• Assemblyrequiresthefollowingtools:
the included hex keys
one Phillips screwdriver
To avoid damaging parts, do not use power tools.
1
Wire
Tie
Wire
Tie
78
77
78
77
7
2. Attach the Upright (77) to the Base (80) with two
3/8" x 5 1/2" Screws (5), two 3/8" Star Washers
(8), and a 3/8” x 2 3/4” Screw (17) with a 3/8”
Star Washer (8) as shown. Start all three
Screws, and then tighten them. Be careful
not to pinch the Upright Wire (not shown) in
the Upright.
Attach the other Upright (not shown) as de-
scribed above. Note: There is not a wire on the
left side.
2
77
5
8
17
8
80
3. Set the Console (37) face down on a soft surface to avoid scraching the Console. Remove
and discard the four screws (A) from the
Console Base Back (89). Lift off the Console
Base Back.
3
A
89
A
37
8
4. Have a second person hold the console assembly near the Uprights (77). Insert the console
wire and the “R” pulse wire from the console assembly through the indicated tie.
Connect the Upright Wire (78) to the wire ex-
tending from the console assembly. See the
inset drawing. The connectors should slide
together easily and snap into place. If they
do not, turn one connector and try again. IF
YOU DO NOT CONNECT THE CONNECTORS
PROPERLY, THE CONSOLE MAY BECOME
DAMAGED WHEN YOU TURN ON THE
POWER.
4
Tie
78
R
Console
Wire
“R” Pulse
Wire
Console
Assembly
L
Remove the wire tie from the Upright Wire (78).
5. Insert the Upright Wire (78) into the right Upright
(77) as you insert the Console Crossbar (101)
into the Uprights. Be careful not to pinch the
Upright Wire (78).
Loosen the four #8 x 1” Screws (102) (only two
are shown) one turn.
Tighten two 5/16" x 2 1/2" Screws (4) with two
5/16" Star Washers (9) into the side of the right
Upright (77) and into the Crossbar (103). Do
not overtighten the Screws. Be careful not to
pinch the Upright Wire (78).
Wire Tie
77
Console
Wire
78
5
101
78
4
9
102
Next, tighten two 5/16" x 5/8" Screws (11) into
the right Upright (77) and the Console Crossbar
(101). It may be necessary to slide the
Console Crossbar (102) to align the holes.
Then, tighten the two #8 x 1" Screws (102).
Repeat this step on the other side of the in-
cline trainer.
R
103
L
11
77
9
6. Tighten two #8 x 3/4" Screws (1) into the
Console Base (87). Do not overtighten the
Screws.
Identify the right handrail assembly (B). Hold the
right handrail assembly near the right Upright
(77). Insert the wire from the right handrail assembly into the hole in the top of the Upright
and out of the end of the Upright.
6
1
7. Set the right handrail assembly (B) onto the
right Upright (77). Make sure that no wires are
pinched. Attach the right handrail assembly
with two 3/8" x 5 1/2" Screws (5) and two 3/8"
Star Washers (8). Note: Start the lower Screw
first.
Connect the two “R” pulse wires.
B
Wire
1
87
77
7
B
“R”
Pulse
Wires
R
R
10
77
Assembly
8
5
Start First
L
Console
“L” Pulse
Wire
8. Hold the left handrail assembly (C) near the left
Upright (77). Insert the pulse wire from the left
handrail assembly into the hole in the top of the
Upright and out of the end of the Upright.
8
Set the left handrail assembly (C) onto the left
Upright (77). Make sure that no wires are
pinched. Attach the left handrail assembly with
two 3/8" x 5 1/2" Screws (5) and two 3/8" Star
Washers (8). Note: Start the lower Screw first.
Insert the pulse wire through the three ties (only
two are shown). Connect the two “L” pulse wires
(see also step 7).
Ties
R
C
Pulse
Wire
L
Tie
77
8
5
9. Attach the Console Base Back (89) to the
Console Base (87) with nine #8 x 3/4" Machine
Screws (16) and two #8 x 3/4" Screws (1) in
the locations shown. Start all eleven Screws,
and then tighten them. Do not overtighten
the Screws. Make sure that no wires are
pinched.
Start First
9
87
16
16
16
16
89
16
1
1
11
10. See page 14 and plug in the power cord. Next,
see page 16 and turn on the power. Then, touch
the Incline button numbered 40 on the console.
The Frame (58) will adjust to an incline of 40
percent. Then, unplug the power cord.
Identify the Left Inside Cover (110) and the Left
Outside Cover (106). Next, hold the Left Inside
Cover against the left Upright (77). Then, hold
the Left Ouside Cover against the Left Inside
Cover.
10
58
Attach the Left Outside Cover (106) to the Left
Inside Cover (110) with a #8 x 1 1/4" Screw (36)
and two #8 x 3/4" Screws (1). Start all three
Screws and then tighten them.
Attach the Right Inside Cover and the Right
Outside Cover (not shown) as described
above.
11. Make sure that all parts are properly tightened before you use the incline trainer. Keep the included hex
keys in a secure place. One of the hex keys is used to adjust the walking belt (see pages 29 and 30). To pro-
tect the floor or carpet from damage, place a mat under the incline trainer.
36
1
77
106
110
12
THE CHEST HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
The heart rate
monitor consists of
a chest strap and a
sensor. Insert the
tab on one end of
the chest strap into
the hole in one end
of the sensor as
shown. Then, press
the end of the sensor under the buckle
on the chest strap.
The tab should be
ushwiththefront
of the sensor.
The heart rate monitor must be worn
under your clothes,
tight against your
skin. Wrap the heart
rate monitor around
your chest in the location shown. Make
sure that the logo is
right-side-up. Then,
attach the other end of the chest strap to the sensor.
Adjust the length of the chest strap, if necessary.
Pull the sensor away from your body a few inches and
locate the two electrode areas, which are covered by
shallow ridges. Using saline solution such as saliva or
contact lens solution, wet the electrode areas. Then,
return the sensor to a position against your chest.
CARE AND MAINTENANCE
• Thoroughlydrythesensorwithasofttowelafter
each use. Moisture may keep the sensor activated,
shortening the life of the battery.
•Storetheheartratemonitorinawarm,dryplace.
Do not store the heart rate monitor in a plastic bag
or other container that may trap moisture.
Tabs
Chest
Sensor
Strap
Sensor
Tab
Buckle
•Donotexposetheheartratemonitortodirect
sunlight for extended periods of time; do not expose
it to temperatures above 122° F (50° C) or below 14°
F (-10° C).
•Donotexcessivelybendorstretchthesensorwhen
using or storing the heart rate monitor.
•Tocleanthesensor,useadampclothandasmall
amount of mild soap. Then, wipe the sensor with a
damp cloth and thoroughly dry it with a soft towel.
Never use alcohol, abrasives, or chemicals to clean
the sensor. Hand wash and air dry the chest strap.
TROUBLESHOOTING
If the heart rate monitor does not function properly, try
the steps below.
• Makesurethatyouarewearingtheheartratemonitor as described at the left. If the heart rate monitor
does not function when positioned as described,
move it slightly lower or higher on your chest.
• Ifheartratereadingsarenotdisplayeduntilyou
begin perspiring, rewet the electrode areas.
• Fortheconsoletodisplayheartratereadings,you
must be within arm’s length of the console.
• Ifthereisabatterycoveronthebackofthesensor,
replace the battery with a new battery of the same
type.
• Theheartratemonitorisdesignedtoworkwith
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
• Theoperationoftheheartratemonitorcanbe
affected by magnetic interference from high power
lines or other sources. If you suspect that magnetic
interference is causing a problem, try relocating the
tnessequipment.
13
OPERATION AND ADJUSTMENT
HOW TO PLUG IN THE POWER CORD
DANGER: Improper connec-
tion of the equipment-grounding conductor
increases the risk of electric shock. Check
with a qualied electrician or serviceman if
you are unsure whether the product is properly grounded. Do not modify the plug—if it
will not t the outlet, have a proper outlet installed by a qualied electrician.
Your incline trainer, like other electronic equipment,
can be damaged by sudden voltage changes in your
home’s power. To decrease the risk of damaging
your incline trainer, always use a surge suppressor with your incline trainer (see drawing 1 at the
right). To purchase a surge suppressor, see precaution 12 on page 3.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have
a UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly-functioning surge suppressor could damage the control system of the incline trainer (see
precaution 13 on page 3).
This product must be grounded. If it should mal-
function or break down, grounding provides a path
of least resistance for electric current to reduce the
risk of electric shock. This product’s power cord has
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
IMPORTANT: The incline trainer is not compatible
with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit
(see drawing 1). A temporary adapter may be used to
connect the surge suppressor to a 2-pole receptacle if
a properly-grounded outlet is not available (see
drawing 2).
1
Grounded Outlet
2
Metal Screw
The temporary adapter should be used only until a
properly-grounded outlet (see drawing 1) can be in-
stalledbyaqualiedelectrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly-grounded outlet box cover.
The adapter must be held in place by a metal screw.
Some 2-pole receptacle outlet box covers are not
grounded. Contact a qualied electrician to determine if the outlet box cover is grounded before
using an adapter.
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Grounding Pin
Grounding Plug
Grounded Outlet Box
Adapter
Lug
Grounding Plug
Surge Suppressor
14
CONSOLE
DIAGRAM
FEATURES OF THE CONSOLE
The incline trainer console offers an impressive array
of features designed to make your workouts more effective and enjoyable. The console features revolutionary iFit Live technology that enables the incline trainer
to communicate with your wireless network. With iFit
Live technology, you can download personalized workouts, create your own workouts, track your workout
results, and access many other features. See
www.iFit.com for complete information.
In addition, the console features a selection of onboard
workouts, including at least eight calorie workouts,
eight intensity workouts, eight speed workouts, eight
incline workouts, and six iFit Live demo workouts.
Each workout automatically controls the speed and
incline of the incline trainer as it guides you through an
effective exercise session. In addition, you can set a
calorie, time, distance, or pace goal.
When you use the manual mode, you can change the
speed and incline of the incline trainer with the touch of
a button.
As you exercise, the console will display instant exercise feedback. You can also measure your heart
rate using the handgrip heart rate monitor or the chest
heart rate monitor.
You can even browse the Internet or listen to your favorite workout music or audio books with the console’s
stereo sound system while you exercise.
To turn on the power, see page 16. To learn how to
use the touch screen, see page 16. To set up the
console, see page 17.
Note: The console can display speed and distance in
eithermilesorkilometers.Tondwhichunitofmeasurement is selected, see step 4 on page 23. For simplicity, all instructions in this section refer to miles.
15
HOW TO TURN ON THE POWER
HOW TO USE THE TOUCH SCREEN
IMPORTANT: If the incline trainer has been exposed to cold temperatures, allow it to warm to
room temperature before you turn on the power. If
you do not do this, you may damage the console
display or other electrical components.
Plug in the power cord (see
page 14). Next, locate the
power switch on the incline
trainer frame near the power
cord. Make sure that the
Reset
switch is in the reset position.
IMPORTANT: The console features a display demo
mode, designed to be used if the incline trainer is
displayed in a store. If the demo mode is turned
on, the screen will show a demo presentation after
you plug in the power cord and press the power
switch into the reset position, before you insert
the key. To turn off the demo mode, see step 5 on
page 23.
Next, stand on the
foot rails of the incline
trainer. Locate the clip
Key
attached to the key, and
slide the clip securely
onto the waistband of
your clothes. Then,
insert the key into the
Clip
console. Note: It may
take a minute for the
console to be ready for use. IMPORTANT: In an
emergency, the key can be pulled from the console, causing the walking belt to slow to a stop.
Test the clip by carefully taking a few steps backward; if the key is not pulled from the console, adjust the position of the clip.
The console features a tablet with a full-color touch
screen. The following information will help you become
familiar with the tablet’s advanced technology:
•Theconsolefunctionssimilarlytoothertablets.
You can slide or flick your finger against the screen
to move certain images on the screen, such as
the displays in a workout (see step 5 on page 18).
However, you cannot zoom in and out by sliding
your fingers on the screen.
•Thescreenisnotpressuresensitive.Youdonot
need to press hard on the screen.
•Totypeinformationintoatextbox,touchthetext
box to view the keyboard. To use numbers or other
characters on the keyboard, touch the ?123 button. To view more characters, touch the Alt button.
Touch the Alt button again to return to the number
keyboard. To return to the letter keyboard, touch the
ABC button. To use a capital character, touch the
button with an upward-facing arrow. To use multiple
capital characters, touch the arrow button again. To
return to the lowercase keyboard, touch the arrow
button a third time. To clear the last character, touch
the button with a backward-facing arrow and an X.
•Usethebuttonsontheconsoleshownbelowto
navigate the tablet. Press the Back button to return
to the previous screen. Press the Home button to return to the main menu. Note: The center button does
not function.
Back Home
16
HOW TO SET UP THE CONSOLE
Before using the incline trainer for the first time, set up
the console.
1. Connect to your wireless network.
Note: In order to access the Internet, download
iFit Live workouts, and use several other features
of the console, you must be connected to a wireless network. See HOW TO USE THE WIRELESS
NETWORK MODE on page 25 to connect the console to your wireless network.
2. Check for firmware updates.
First, see step 1 on page 23 and step 2 on page 24
and select the maintenance mode. Then, see step
3 on page 24 and check for firmware updates.
Next, enter a username and password and your
e-mail address. Enter the activation code from
the iFit Live flier that came with the incline trainer.
Touch the Place of Purchase drop-down menu
for a list of options; then, touch the location where
you purchased your product. Touch the words
MEDICAL DISCLAIMER, read the medical disclaimer, touch the I Accept button, and check the
medical disclaimer checkbox. Then, touch the
Confirm Activation Code button.
Enter the requested personal information. When
you have entered all of the information, touch the
Finish button. Then, touch the Home button on the
console to exit the browser.
The console is now ready for you to begin working out.
The following pages explain the various workouts and
other features that the console offers.
3. Calibrate the incline system.
See step 4 on page 24 and calibrate the incline
system of the incline trainer.
4. Create an iFit Live account.
Touch the globe button near the lower-left corner
of the screen and touch the iFit Live button.
Note: For information about navigating in the
browser, see page 26. The browser will open to the
iFit.com home page. Touch the Register button in
the upper-right corner of the screen.
The browser will open to the iFit.com registration
page. Touch an entry box to view the keyboard.
Slide your finger up or down the screen to scroll up
or down the page.
To use the manual mode, see page 18. To use an
onboard workout, see page 20. To use a set-a-goal
workout, see page 21. To use an iFit Live workout,
see page 22.
To use the equipment settings mode, see page 23.
To use the maintenance mode, see page 24. To use
the wireless network mode, see page 25. To use
the stereo sound system, see page 26. To use the
Internet browser, see page 26.
IMPORTANT: If there are sheets of plastic on the
console, remove the plastic. To prevent damage
to the walking platform, wear clean athletic shoes
while using the incline trainer. The first time you
use the incline trainer, observe the alignment of
the walking belt, and center the walking belt if necessary (see page 30).
17
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
16. Note: It may take a minute for the console
to be ready for use.
2. Select the main menu.
When you turn
on the power,
the main menu
should appear after the
console boots
up. Touch the
home button in
the lower-left
corner of the screen to return to the main menu at
any time.
3. Start the walking belt and adjust the speed.
Touch the Start button on the screen or press the
Start button on the console to start the walking
belt. You can also press the Manual button on the
console, and then touch the Resume button on
the screen. The walking belt will begin to move at
1 mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed increase and decrease buttons. Each time you press
one of the buttons, the speed setting will change
by 0.1 mph; if you hold down the button, the speed
setting will change in increments of 0.5 mph.
If you press one of the numbered 1 Step Speed
buttons, the walking belt will gradually change
speed until it reaches the selected speed setting.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button.
4. Change the incline of the incline trainer as
desired.
8 mph; when the incline is from -2% to -1.5%, the
maximum speed will be 8.5 mph; when the incline
is from -1% to -0.5%, the maximum speed will be
9 mph; when the incline is from 0% to 15%, the
maximum speed will be 12 mph; when the incline
is from 15.5% to 25%, the maximum speed will be
8 mph; and when the incline is from 25.5% to 40%,
the maximum speed will be 6 mph.
Note: The first time you adjust the incline, you must
first calibrate the incline system (see step 4 on
page 24).
5. Monitor your progress.
The console
offers several display
modes. The
display mode
that you select
will determine
which workout
information is shown. To select the desired display
mode, simply flick or slide the screen (see page
16). You can also view additional information by
touching the red boxes on the screen.
As you walk or run on the incline trainer, the
screen can show the following workout information:
•Theinclineleveloftheinclinetrainer
•Theelapsedtime
• Thetimeleft(Note:Themanualmodedoesnot
have a time left countdown.)
•Theapproximatenumberofcaloriesyouhave
burned
• Theapproximatenumberofcaloriesyouare
burning per hour
• Thedistancethatyouhavewalkedorrun
To change the incline of the incline trainer, press
the Incline/Decline buttons or one of the numbered
1 Step Incline/Decline buttons. Each time you
press one of the buttons, the incline will gradually
change until it reaches the selected incline setting.
Note: As the incline changes, the maximum speed
of the incline trainer may change. When the incline
is from -6% to -5%, the maximum speed will be 6
mph; when the incline is from -4.5% to -3.5%, the
maximum speed will be 7 mph; when the incline
is from -3% to -2.5%, the maximum speed will be
• Thenumberofverticalfeetyouhaveclimbed
• Thespeedofthewalkingbelt
• Atrackrepresenting1/4mile(400m)
•Yourpaceinminutespermile
• Yourcurrentlapnumber
• Yourheartrate(seestep6)
18
The displays at the top of the screen can show two
types of information. Touch each display until the
display shows the desired information.
If desired, adjust the volume by pressing the
Volume increase and decrease buttons on the
console.
7. Turn on the fan if desired.
The fan features several speed settings and an
auto mode. When the auto mode is selected, the
speed of the fan will automatically increase and decrease as the speed of the walking belt increases
and decreases.
To pause the workout, touch one of the menu but-
tons or press the Stop button on the console. To
continue the workout, touch the Resume button or
the Start button. To end the workout session, touch
the End Workout button.
6. Measure your heart rate if desired.
Before using
the handgrip heart
rate monitor,
remove the
sheets of plas-
Contacts
tic from the
metal contacts.
In addition,
make sure that
your hands are
clean.
To measure your heart rate, stand on the foot
rails and hold the contacts with your palms for
approximately ten seconds; avoid moving your
hands. When your pulse is detected, your heart
rate will be shown. For the most accurate heart
rate reading, continue to hold the contacts for
about 15 seconds.
Press the Manual fan button repeatedly to select
a fan speed or to turn off the fan. Press the Auto
fan button to select the auto mode or to turn off the
fan.
8. When you are finished exercising, remove the
key from the console.
Step onto the walking platform and touch the home
button or the back button on the screen or press
the Stop button on the console. A workout summary will appear on the screen. After you view the
workout summary, touch the Finish button to return
to the main menu. You may also be able to either
save or publish your results using one of the options on the screen. Then, remove the key from the
console and put it in a secure place.
When you are finished using the incline trainer,
press the power switch into the off position and unplug the power cord. IMPORTANT: If you do not
do this, the incline trainer’s electrical components may wear prematurely.
19
HOW TO USE AN ONBOARD WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
16.
2. Select an onboard workout.
To select an onboard workout, press the Calorie
button, the Intensity button, or the Incline button on
the console. Note: You can also touch the runner
icon on the screen to select the Workouts menu.
Then, select the desired workout. The screen will
show the name, duration, and distance of the workout. The screen will also show the approximate
number of calories you will burn during the workout
andaproleoftheinclinesettingsoftheworkout.
3. Start the workout.
Touch the Start Workout button to start the work-
out. A moment after you touch the button, the walking belt will begin to move. Hold the handrails and
begin walking.
Each workout is divided into several segments.
One speed setting and one incline setting are
programmed for each segment. Note: The same
speed setting and/or incline setting may be programmed for consecutive segments.
Duringtheworkout,theprolewillshowyourprog-
ress.Toviewtheprole,ickorslidethescreen.
The vertical colored line will indicate the current
segmentoftheworkout.Thebottomprolerepresents the incline setting of the current segment.
Thetopprolerepresentsthespeedsettingofthe
current segment.
If the speed or incline setting is too high or too low
at any time during the workout, you can override
the setting by pressing the Speed or Incline buttons; however, when the next segment begins,
the incline trainer will automatically adjust to
the speed and incline settings for the next
segment.
To pause the workout, touch either the back button
or the home button in the lower-left corner of the
screen, or press the Stop button on the console.
To continue the workout, touch the Resume button
or press the Start button on the console. To end
the workout, touch the End Workout button.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on your metabolic rate. In
addition, if you manually change the speed or
incline of the incline trainer during the workout,
the number of calories you burn will be
affected.
4. Monitor your progress.
See step 5 on page 18. The screen can also show
aproleofthespeedandinclinesettingsofthe
workout.
5. Measure your heart rate if desired.
See step 6 on page 19.
6. Turn on the fan if desired.
See step 7 on page 19.
7. When you are nished exercising, remove the
key from the console.
Attheendoftherstsegmentoftheworkout,the
incline trainer will automatically adjust to the speed
and/or incline settings for the next segment.
The workout will continue in this way until the last
segment ends. The walking belt will then slow to
a stop and a workout summary will appear on the
screen. After you view the workout summary, touch
the Finish button to return to the main menu. You
may also be able to either save or publish your results using one of the options on the screen.
See step 8 on page 19.
20
HOW TO USE A SET-A-GOAL WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
16.
2. Select the main menu.
See step 2 on page 18.
3. Select a set-a-goal workout.
To select a set-a-goal workout, touch the Set A
Goal button on the screen or press the Set A Goal
button on the console.
To set a calo-
rie, time, distance, or pace
goal, touch the
Calories, Time,
Distance, or
Pace button.
Then, touch
the increase
and decrease buttons on the screen to select a
calorie, time, distance, or pace goal and to select
the speed and incline for the workout. The screen
will show the duration and distance of the workout,
and the approximate number of calories you will
burn during the workout.
The workout will function in the same way as the
manual mode (see pages 18 and 19).
The workout will continue until you reach the goal
that you set. The walking belt will then slow to a
stop, and a workout summary will appear on the
screen. After you view the workout summary, touch
the Finish button to return to the main menu. You
may also be able to either save or publish your results using one of the options on the screen.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on your metabolic rate.
5. Monitor your progress.
See step 5 on page 18.
6. Measure your heart rate if desired.
See step 6 on page 19.
7. Turn on the fan if desired.
See step 7 on page 19.
8. When you are finished exercising, remove the
key from the console.
See step 8 on page 19.
4. Start the workout.
Touch the Start button to start the workout. A mo-
ment after you touch the button, the walking belt
will begin to move. Hold the handrails and begin
walking.
21
HOW TO USE AN IFIT LIVE WORKOUT
Note: To use an iFit Live workout, you must have access to a wireless network (see HOW TO USE THE
WIRELESS NETWORK MODE on page 25). An iFit
Live account is also required.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
16.
2. Select the main menu.
Before some workouts will download, you must
add them to your schedule on iFit.com.
For more information about the iFit Live work-
outs, please see www.iFit.com.
When you select an iFit Live workout, the screen
will show the name, duration, and distance of the
workout. The screen will also show the approximate number of calories you will burn during the
workout. If you select a competition workout, the
display will count down to the beginning of the
race.
See step 2 on page 18.
3. Log in to your iFit Live account.
If you have not already done so, touch the Login
button to log in to your iFit Live account. The
screen will ask for your iFit.com username and
password. Enter them and touch the Submit button. Touch the Cancel button to exit the login
screen.
4. Select an iFit Live workout.
To download
an iFit Live
workout in
your schedule, touch the
Map, Train,
Video, or Lose
Weight button
to download
the next workout of that type in your schedule.
Note: You may be able to access demo workouts
through these options, even if you do not log in to
an iFit Live account.
5. Start the workout.
See step 4 on page 20.
During some workouts, the voice of a personal
trainer will guide you through your workout.
6. Monitor your progress.
See step 5 on page 18. The screen may also show
a map of the trail you are walking or
running.
During a competition workout, the screen will show
the speeds of the runners and the distances they
have run. The screen will also show the numbers
of seconds that the other runners are ahead of you
or behind you.
7. Measure your heart rate if desired.
See step 6 on page 19.
8. Turn on the fan if desired.
See step 7 on page 19.
To compete in a race that you have previously
scheduled, touch the Compete button. To view
your Workout History, touch the Track button. To
use a set-a-goal workout, touch the Set A Goal
button (see page 21). Note: You can also press
one of the iFit Live buttons on the console.
To switch users within the account, touch the user
button near the lower right corner of the screen.
9. When you are finished exercising, remove the
key from the console.
See step 8 on page 19.
For more information about the iFit Live mode, go
to www.iFit.com.
22
HOW TO USE THE EQUIPMENT SETTINGS MODE
The console features an equipment settings mode
that allows you to select a language and the unit of
measurement, to turn on and turn off the display demo
mode, and to enable or disable the key.
1. Select the settings main menu.
reset position, and insert the key into the console.
However, when you remove the key, the screen
will show a demo presentation.
To turn on or turn off the display demo mode, first
touch the Demo Mode button. Next, touch the On
checkbox or the Off checkbox. Then, touch the
back button on the screen.
Insert the key into the
console (see HOW
TO TURN ON THE
POWER on page 16).
Next, select the main
menu (see step 2 on
page 18). Then, touch
the gears button near
the lower right corner of the screen to select the
settings main menu.
2. Select the equipment settings mode.
In the settings main menu, touch the Equipment
Settings button.
3. Select a language.
To select a language, touch the Language button
and select the desired language. Then, touch the
back button on the screen to return to the equipment settings mode. Note: This feature may not be
enabled.
4. Select the unit of measurement.
6. Enable or disable the key.
Note: This feature may not be enabled on your in-
cline trainer.
You can disable the key so that the incline trainer
does not require the use of the key if desired.
Touch the Safety Key button. To disable the key,
touch the Disable checkbox. CAUTION: Read
the safety warning on the screen before disabling the key. To enable the key again, touch the
Enable checkbox.
7. Enable or disable a passcode.
The console features a child safety passcode, de-
signed to prevent unauthorized users from using
the incline trainer.
Touch the Passcode button. To enable a pass-
code, touch the Enable checkbox. Then, enter a
4-digit passcode of your choice. Touch Save to use
this passcode. Touch Cancel to return to the equipment settings mode and not use a passcode. To
disable the passcode, touch the Disable checkbox.
Touch the US/Metric button to view the selected
unit of measurement. Change the unit of measurement, if desired. Then, touch the back button on
the screen.
5. Turn on or turn off the display demo mode.
The console features a display demo mode, de-
signed to be used if the incline trainer is displayed
in a store. While the demo mode is turned on, the
console will function normally when you plug in
the power cord, press the power switch into the
Note: If a passcode is enabled, the console will
regularly ask for you to enter the passcode. The
console will remain locked until the correct passcode is entered. IMPORTANT: If you forget your
passcode, enter the following master passcode
to unlock the console: 1985.
8. Exit the equipment settings mode.
To exit the equipment settings mode, touch the
back button on the screen.
23
HOW TO USE THE MAINTENANCE MODE
The console features a maintenance mode that allows you to update the console firmware, calibrate the
incline of the incline trainer, calibrate the screen, view
technical information, and view a button’s keycode.
1. Select the settings main menu.
See step 1 on page 23.
2. Select the maintenance mode.
USB drive. Safely remove the USB drive from your
computer and plug it into the USB port on the side
of the console. The update should begin
automatically.
The screen will show the progress of the update.
When the update is complete, the incline trainer
will turn off and then turn back on. If it does not,
press the power switch into the off position. Wait
for several seconds, and then press the power
switch into the reset position. Note: It may take a
few minutes for the console to be ready for use.
In the settings
main menu,
touch the
Maintenance
button to enter
the maintenance mode.
The maintenance mode main screen will show
information about the model and version of the incline trainer.
3. Update the console firmware.
For the best results, regularly check for firm-
ware updates.
Touch the Firmware Update button to check for
firmware updates using your wireless network. The
update will begin automatically.
To avoid damaging the incline trainer, do not
turn off the power or remove the key while the
firmware is being updated.
Note: Occasionally, a firmware update may cause
your console to function slightly differently. These
updates are always designed to improve your exercise experience.
4. Calibrate the incline system of the incline
trainer.
Touch the Calibrate Incline button. Then, touch the
Begin button to calibrate the incline system. The incline trainer will automatically rise to the maximum
incline level, lower to the minimum incline level,
and then return to the starting position. This will
calibrate the incline system. Press the Cancel button to return to the maintenance mode. When the
incline system is calibrated, touch the Finish
button.
IMPORTANT: Keep pets, feet, and other objects
away from the incline trainer while the incline
system is calibrating. In an emergency, pull the
key from the console to stop the incline
calibration.
5. View machine information.
Touch the Machine Info button to view information
about your incline trainer. After you view the information, touch the back button on the screen.
6. Find Keycodes.
This option is intended to be used by service tech-
nicians to identify whether a certain button is working correctly.
Note: If you cannot update the console firmware
over your wireless network, you can update the
firmware using a USB drive. Go to www.iFit.com
and download the latest firmware update onto your
7. Exit the maintenance mode.
To exit the maintenance mode, press the back but-
ton on the console.
24
HOW TO USE THE WIRELESS NETWORK MODE
The console features a wireless network mode that allows you to set up a wireless network connection.
1. Select the settings main menu.
See step 1 on page 23.
An information box will ask if you want to connect
to the wireless network. Touch the Connect button
to connect to the network or touch the Cancel button to return to the list of networks. If the network
has a password, touch the password entry box. A
keyboard will appear on the screen. To view the
password as you type it, touch the Show Password
checkbox.
2. Select the wireless network mode.
In the settings main menu, touch the Wireless
Network button to enter the wireless network
mode.
3. Enable Wi-Fi.
Make sure that the Wi-Fi checkbox is marked with
a green checkmark. If it is not, touch the Wi-Fi
menu option once and wait for a few seconds. The
console will search for available wireless networks.
4. Set up and manage a wireless network
connection.
When Wi-Fi is enabled, the screen will show a list
of available networks. Note: It may take several
seconds for the list of wireless networks to appear.
Make sure that the checkbox on the Network
notification menu option is marked with a green
checkmark to have the console notify you when a
wireless network is within range and available.
Note: You must have your own wireless network
and an 802.11b/n router with SSID broadcast enabled (hidden networks are not supported).
When a list of networks appears, touch the desired
network. Note: You will need to know your network
name (SSID). If your network has a password, you
will also need to know the password.
To use the keyboard, see HOW TO USE THE
TOUCH SCREEN on page 16.
When the console is connected to your wireless
network, the WiFi menu option at the top of the
screen will display the word CONNECTED. Then,
press the back button on the console to return to
the wireless network mode.
To disconnect from a wireless network, select the
wireless network and then touch the Forget button.
If you are having problems connecting to an en-
crypted network, make sure that your password is
correct. Note: Passwords are case-sensitive.
Note: The iFit Live mode supports unsecured and
secured (WEP, WPA, and WPA2) encryption. A
broadband connection is recommended; performance depends on connection speed.
Note: If you have questions after following
these instructions, go to www.iFit.com/support
for assistance.
5. Exit the wireless network mode.
To exit the wireless network mode, press the back
button on the console.
25
HOW TO USE THE STEREO SOUND SYSTEM
HOW TO USE THE INTERNET BROWSER
To play music or audio books through the console’s
speakers, you must connect your MP3 player, CD
player, or other personal audio player to the console.
Locate the audio wire. Plug one end into the audio jack
on the side of the console. Then, plug the other end
into a jack on your MP3 player, CD player, or other
personal audio player. Make sure that the audio wire
is fully plugged in.
Next, press the play button on your MP3 player, CD
player, or other personal audio player. Then, adjust the
volume level on your personal audio player or press
the Volume increase and decrease buttons on the
console.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat surface instead of on the console.
Note: The USB port on the side of the console is for
firmware updates only.
Note: To use the browser, you must have access to
a wireless network including an 802.11b/n router with
SSID broadcast enabled (hidden networks are not supported).
To open the browser, touch the globe button near the
lower left corner of the screen. Then, select a website.
To return to the previous web page, press the back
button on the console or touch the Browser Back button on the screen. To exit the browser, press the home
button on the console or touch the Return button on
the screen.
To use the keyboard, see HOW TO USE THE TOUCH
SCREEN on page 16.
To enter a different web address in the URL bar, first,
slide your finger down the screen to view the URL bar,
if necessary. Then, touch the URL bar, use the keyboard to enter the address, and touch the Go button.
Note: While you are using the browser, the speed, incline, fan, and volume buttons will still function, but the
workout buttons will not function.
Note: If you have questions after following these
instructions, go to www.iFit.com/support for
assistance.
26
HOW TO MOVE THE INCLINE TRAINER
Before moving the incline trainer, insert the key into the
console, raise the incline to the maximum incline level,
remove the key, and unplug the power cord.
Console
Due to the size and weight of the incline trainer, moving it requires two or three persons. Hold the uprights
firmly near the console. Tip the incline trainer back until it
rolls freely on the wheels. CAUTION: To decrease the pos-
sibility of injury or of damage to the incline trainer, do
not lift the incline trainer by the plastic belly pan. Do not
pull on the console.
Carefully roll the incline trainer on the wheels to the desired
location, and then lower it to the level position. CAUTION:
To reduce the risk of injury, use extreme caution while
moving the incline trainer. Do not attempt to move the
incline trainer over uneven surfaces.
Belly
Pan
Upright
Wheel
27
TROUBLESHOOTING
Most incline trainer problems can be solved by following the simple steps below. Find the symptom
that applies, and follow the steps listed. If further
assistance is needed, see the front cover of this
manual.
SYMPTOM: The power does not turn on
a. Make sure that the power cord is plugged into a
surge suppressor, and that the surge suppressor is
plugged into a properly-grounded outlet (see page
14). Use only a single-outlet surge suppressor that
meets all of the specifications described on page
14. IMPORTANT: The incline trainer is not com-
patible with GFCI-equipped outlets and may
not be compatible with AFCI-equipped outlets.
b. After the power cord has been plugged in, make
sure that the key is inserted into the console.
c. Check the power switch located on the incline
trainer frame near the power cord. If the switch
protrudes as shown, the switch has tripped. To
reset the power switch, wait for five minutes and
then press the switch back in.
c. Remove the key from the console, and then
reinsert it.
d. If the incline trainer still will not run, please see the
front cover of this manual.
SYMPTOM: The console displays remain lit when
you remove the key from the console
a. The console features a display demo mode, de-
signed to be used if the incline trainer is displayed
in a store. If the screen remains lit when you remove the key, the demo mode is turned on. To turn
off the demo mode, see step 5 on page 23.
SYMPTOM: The console does not display speed
and distance correctly
a. Remove the key from the console and UNPLUG
THE POWER CORD. Next, remove the three indi-
cated #8 x 1/2" Cover Screws (18) and the #8 x 1
1/4" Screw (36). Lift off the Left Roller Cover (38).
a
36
c
Tripped
SYMPTOM: The power turns off during use
a. Check the power switch (see the drawing above).
If the switch has tripped, wait for five minutes and
then press the switch back in.
b. Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
Reset
38
18
18
28
Locate the Reed Switch (55) and the Magnet (41)
on the left side of the Pulley (42). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet
and the Reed Switch is about 1/8 in. (3 mm). If
necessary, loosen the #8 x 3/4" Clamp Screw (20),
move the Reed Switch slightly, and then retighten
the Screw. Reattach the Left Roller Cover (not
shown) and run the incline trainer for a few minutes
to check for a correct speed reading.
Top
View
1/8 in.
20
41
b. If the walking belt is overtightened, incline trainer
performance may decrease and the walking belt
may become damaged. Remove the key and
UNPLUG THE POWER CORD. Using the hex
key, turn both idler roller screws counterclockwise,
1/4 of a turn. When the walking belt is properly
tightened, you should be able to lift each edge of
the walking belt 3 to 4 in. (8 to 10 cm) off the walking platform. Be careful to keep the walking belt
centered. Then, plug in the power cord, insert the
key, and run the incline trainer for a few minutes.
Repeat until the walking belt is properly tightened.
b
3–4 in.
55
SYMPTOM: The incline of the incline trainer does
not change correctly
a. Calibrate the incline system (see step 4 on page
24).
SYMPTOM: The walking belt slows when walked on
a. Use only a single-outlet surge suppressor that
meets all of the specifications described on page
14.
42
Idler Roller Screws
c. Your incline trainer features a walking belt coated
with high-performance lubricant. IMPORTANT:
Never apply silicone spray or other substances
to the walking belt or the walking platform unless instructed to do so by an authorized service representative. Such substances may deteriorate the walking belt and cause excessive
wear. If you suspect that the walking belt needs
more lubricant, see the front cover of this manual.
d. If the walking belt still slows when walked on, see
the front cover of this manual.
29
SYMPTOM: The walking belt is off-center or slips
when walked on
SYMPTOM: The iFit Live mode does not function
correctly
a. If the walking belt is off-center, first adjust incline
to 40 percent. Remove the key and UNPLUG THE
POWER CORD. If the walking belt has shifted to
the left, use the hex key to turn the left idler roller
screw clockwise 1/2 of a turn; if the walking belt
has shifted to the right, turn the left idler roller
screw counterclockwise 1/2 of a turn. Be careful
not to overtighten the walking belt. Then, plug in
the power cord, insert the key, and run the incline
trainer for a few minutes. Repeat until the walking
belt is centered.
a
b. If the walking belt slips when walked on, first
adjust incline to 40 percent. Remove the key and
UNPLUG THE POWER CORD. Using the hex key,
turn both idler roller screws clockwise, 1/4 of a
turn. When the walking belt is correctly tightened,
you should be able to lift each edge of the walking
belt 3 to 4 in. (8 to 10 cm) off the walking platform.
Be careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and carefully walk on the incline trainer for a few minutes.
Repeat until the walking belt is properly tightened.
a. If the iFit Live mode is not functioning correctly,
make sure that the incline trainer has the most current firmware available (see step 3 on page 24).
SYMPTOM: The incline trainer will not connect to
the wireless network
a. Make sure that the wireless settings on your con-
sole are correct (see step 4 on page 25).
b. Make sure that the settings for your wireless net-
work are correct.
c. If you still have questions, see the front cover of
this manual.
b
30
EXERCISE GUIDELINES
WARNING: Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
WORKOUT GUIDELINES
Warming Up—Start with 5 to 10 minutes of stretch-
ing and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise—never hold your breath.
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your "training zone." The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
31
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch —never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back foot
atontheoor.Bendyourfrontleg,leanforwardandmoveyour
hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times
for each leg. To cause further stretching of the achilles tendons,
bend your back leg as well. Stretches: Calves, achilles tendons and
ankles.
4. Quadriceps Stretch
1
2
3
4
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
5
32
PART LIST Model No. NTL19010.0 R0911B
Key No. Qty. Description
Key No. Qty. Description
1 63 #8 x 3/4" Screw
2 8 #8 x 3/4" Tek Screw
3 4 3/8" x 3/4" Screw
4 4 5/16" x 2 1/2" Screw
5 8 3/8" x 5 1/2" Screw
6 2 3/8" Wheel Bolt
7 2 3/8" Nut
8 16 3/8" Star Washer
9 4 5/16" Star Washer
10 4 Base Foot
11 4 5/16" x 5/8" Screw
12 2 Wheel
13 11 #8 x 1/2" Screw
14 1 3/16" Hex Key
15 1 7/32" Hex Key
16 19 #8 x 3/4" Machine Screw
17 2 3/8" x 2 3/4" Screw
18 6 #8 x 1/2" Cover Screw
19 1 Key/Clip
20 1 #8 x 3/4" Clamp Screw
21 4 #8 Belt Guide Screw
22 2 1/4" x 1 1/2" Screw
23 4 5/16" x 1 3/4" Bolt
24 2 1/4" x 1/2" Screw
25 2 1/4" x 2 1/2" Screw
26 1 3/8" x 2 1/2" Bolt
27 1 3/8" x 1 3/4" Bolt
28 8 #8 x 5/8" Screw
29 2 1/4" Motor Screw
30 3 #8 Star Washer
31 2 1/4" Star Washer
32 4 3/8" Jam Nut
33 4 5/16" Nut
34 2 #8 x 1" Screw
35 16 Clip
36 2 #8 x 1 1/4" Screw
37 4 Console
38 1 Left Roller Cover
39 1 Right Roller Cover
40 1 Motor Belt
41 1 Magnet
42 1 Drive Roller/Pulley
43 2 Belt Guide
44 1 Walking Platform
45 1 Rear Cover
46 2 Incline Motor Bushing
47 1 Idler Roller
48 1 Walking Belt
49 1 Front Hood
50 1 Power Cord
51 1 Grommet
52 1 Belly Pan Cover
53 1 Power Switch
54 1 Belly Pan
55 1 Reed Switch
56 1 Reed Switch Clamp
57 2 Axle
58 1 Frame
59 1 Electronics Cover
60 2 Upper Incline Motor Bushing
61 1 Front Belly Pan
62 1 Left Side Deckrail
63 1 Top Incline Motor Cover
64 1 Incline Motor
65 1 Bottom Incline Motor Cover
66 1 Right Side Deckrail
67 2 Wire Clamp
68 1 Left Foot Rail
69 1 Resistor
70 1 Electronics Plate
71 1 Controller
72 1 Right Foot Rail
73 4 Cushion Cap
74 2 Cushion Spring
75 1 Drive Motor
76 1 Console Frame
77 2 Upright
78 1 Upright Wire
79 2 Cushion
80 1 Base
81 3 Round Grommet
82 2 Caution Decal
83 1 Warning Decal
84 2 Base Cap
85 1 Computer
86 1 Left Pulsebar Top
87 1 Console Base
88 2 Handrail
89 1 Console Base Back
90 1 Chest Strap
91 1 Chest Sensor
92 1 Left Pulsebar Bottom
93 1 Right Pulsebar Top
94 1 Right Pulsebar Bottom
95 1 Audio Wire
96 2 Console Fan
97 1 Ground Wire
98 2 Handrail Cap
99 4 #8 x 3/8" Screw
100 6 #3 x 1/4" Screw
33
Key No. Qty. Description
Key No. Qty. Description
101 1 Console Crossbar
102 4 #8 x 1" Screw
103 1 Crossbar
104 2 Console Clamp
105 2 3/8" x 2 1/2" Screw
106 1 Left Outside Cover
107 2 Frame Bushing
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
108 4 Rubber Spacer
109 4 5/16" Flat Washer
110 1 Left Inside Cover
111 1 Right Outside Cover
112 1 Right Inside Cover
113 1 Console Back
* – User’s Manual
34
EXPLODED DRAWING A Model No. NTL19010.0 R0911B
1
1
50
1
25
28
43
1
1
51
13
35
35
18
18
1
35
35
53
1
81
18
1
35
1
1
45
23
1
48
25
1
47
23
1
28
1
21
66
28
1
52
1
1
1
28
1
35
54
35
18
28
35
35
35
1
35
28
21
43
44
1
62
1
23
1
28
28
40
41
35
1
18
35
1
72
23
36
68
36
42
38
39
35
35
35
35
1
15
14
EXPLODED DRAWING B Model No. NTL19010.0 R0911B
13
109
33
108
13
59
63
27
73
49
74
58
79
73
108
109
33
13
73
32
74
60
79
60
26
73
29
108
22
31
32
46
109
33
46
107
65
64
1
1
1
1
1
61
55
108
20
1
69
13
109
33
107
56
22
31
75
13
30
13
13
30
13
71
30
13
70
36
EXPLODED DRAWING C Model No. NTL19010.0 R0911B
111
17
8
10
112
36
1
1
2
81
106
80
78
24
10
82
51
10
2
81
24
84
2
10
2
8
17
110
36
1
1
82
83
51
84
37
EXPLODED DRAWING D Model No. NTL19010.0 R0911B
98
86
88
16
16
16
76
92
8
16
8
3
9
4
8
77
8
16
11
5
93
1
105
16
1
1
94
16
104
1
102
1
103
8
8
105
101
104
1
78
102
1
97
13
1
11
9
4
8
5
6
98
32
16
5
8
12
88
8
3
77
5
8
12
32
6
38
EXPLODED DRAWING E Model No. NTL19010.0 R0911B
99
1
99
100
37
19
96
100
100
87
96
85
100
1
113
1
89
1
16
16
16
1
16
1
16
16
1
16
34
1
16
34
1
67
1
1
90
91
1
1
95
39
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
•themodelnumberandserialnumberoftheproduct(seethefrontcoverofthismanual)
•thenameoftheproduct(seethefrontcoverofthismanual)
•thekeynumberanddescriptionofthereplacementpart(s)(seethePARTLISTandtheEXPLODEDDRAWING
near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
fees for service needed under warranty. Go to www.nordictrackservice.com/registration.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame and drive motor are warranted for a lifetime.
Parts are warranted for five (5) years from the date of purchase. Labor is warranted for two (2) years from
the date of purchase.
This warranty extends only to the original purchaser (customer). ICON’s obligation under this warranty is
limited to repairing or replacing, at ICON’s option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’s responsibility. If
replacement parts are shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to freight damage to the product. This warranty will automatically be voided
if the product is used as a store display model, if the product is purchased or transported outside the USA,
if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used,
oriftheproductisusedforcommercialorrentalpurposes.Nootherwarrantybeyondthatspecicallyset
forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property,lossofrevenuesorprots,lossofenjoymentoruse,orcostsofremovalorinstallation;orother
consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantabilityortnessforaparticularpurposearelimitedintheirscopeanddurationtothetermsset
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer.
Thiswarrantyprovidesspeciclegalrights;thecustomermayhaveotherrightsthatvaryfromstatetostate.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 319498 R0911B Printed in USA © 2011 ICON IP, Inc.
Loading...