The Battery Adapter BDC-3 is used along with an external battery
capacity meter to check battery capacity.
Note that Li-ion batteries have an internal protection circuit to prevent
deep discharge.
Product Code
Battery Adapter BDC-3:0770083
View of BDC-3
THF–13
Service Tools
Issue 1 08/99
Nokia Mobile Phones Ltd.
Page 5
Page 6
THF–13
Service Tools
Service Battery BBD-3
The Service Battery BBD-3 is used in place of the phone’s normal battery
during service, to supply a controlled operating voltage to the phone for
current and charger calibration, and is also required when flashing the
phone.
Note that the cable SCB-3 (0730114) is also required for charger
calibration.
Product Code
Service Battery BBD-3:0775071
View of BBD-3
PAMS Technical Documentation
Page 6
Nokia Mobile Phones Ltd.
Issue 1 08/99
Page 7
PAMS Technical Documentation
Module Jig JBS-24
The Module Jig JBS-24 is used for repair of both system/RF and UIF
modules. *
Product Code
Light Module Jig JBS-24:0770167
View of JBS-24
THF–13
Service Tools
*) Connect the External antenna cable XRC-1B, service Cable SCH-5, and
the DC Cable PCS-1 to the JBS-24 jig.
The service cable SCH-5 can be replaced by the DAU-9P cable.
Note: The nominal supply voltage for JBS-24 is +3.6 V.
The supply voltage must not exceed +5.0 V.
Issue 1 08/99
Nokia Mobile Phones Ltd.
Page 7
Page 8
THF–13
Service Tools
Flash Loading Adapter FLA-5 (Sales Pack)
The Flash Loading Adapter FLA-5 is used with the Service Battery BBD-3
and Service Cable SCH-5. Power is supplied to FLA-5 from the Flash
Security Box TDF-4 via the DC cable PCC-1B, (The PCC-1B cable can be
replaced with a Travel Charger ACH-6), and is connected to the Flash
Prommer FPS-4S with the cable AXS-5.
The sales pack includes:
- Flash Loader Adapter FLA-5 0770085
- Service cable SCH-50730098
- D15 - D15 Cable AXS-50730091
- Installation software for FPS-48400041
Product Code
Flash Loading Adapter FLA-5:0080178
PAMS Technical Documentation
View of FLA-5
Page 8
Nokia Mobile Phones Ltd.
Issue 1 08/99
Page 9
PAMS Technical Documentation
Flash Prommer FPS-4S (Sales Pack)
The Flash Prommer FPS-4S is used to update the main software of the
phone. Updating is done by first loading the new MCU software from the
PC to the flash prommer, and then loading the new SW from the prommer
to the phone. When updating more than one phone in succession, the
MCU software only needs to be loaded to the prommer once.
The sales pack includes:
- Charger ACL-3E0680015
- Printer Cable 0730029
- D9 - D9 Cable AXS-40730090
- Installation software for FPS-48400041
Product Code
Flash Prommer FPS-4S:0085095
THF–13
Service Tools
View of FPS-4S
Issue 1 08/99
Nokia Mobile Phones Ltd.
Page 9
Page 10
THF–13
Service Tools
Service Cable SCH-5A
The Service Cable SCH-5A is used between the phone and Service Audio
Box JBA-4 (or modular T-adapter. It is also used between the phone and
the Flash Loading Adapter FLA-5. The older version, Service Cable
SCH-5 (0730098) can be used instead, but it is no more available.
Product Code
Service Cable SCH-5A:0730166
View of SCH-5A
PAMS Technical Documentation
D9-D9 Cable AXS-4
The D9-D9 cable AXS-4 is used to connect two 9 pin D connectors. e.g. between PC and TDF-4 security box.
Product Code
D9-D9 Cable AXS-4:0730090
View of AXS-4
Page 10
Nokia Mobile Phones Ltd.
Issue 1 08/99
Page 11
PAMS Technical Documentation
Audio Cable ADS-1
Audio cable is an adapter routing AF signals (MIC/EAR) from 8 pin
modular connector to two BNC connectors. It is used to connect JBA-4,
SCH-5, and DAU-9S.
Product code
Audio Cable ADS-1:0730011
View of ADS-1
THF–13
Service Tools
D15-D15 Cable AXS-5
The D15-D15 Cable AXS-5 is used to connect two 15 pin D connectors.
e.g. between FLA-5 and FPS-4S.
Product Code
D15-D15 Cable AXS-5:0730091
View of AXS-5
Issue 1 08/99
Nokia Mobile Phones Ltd.
Page 11
Page 12
THF–13
Service Tools
MBUS Cable DAU-9P
The MBUS Cable DAU-9P has a phone system connector, and is used
between the phone and external devices.
Product Code
MBUS Cable DAU-9P:0730109
View of DAU-9P
PAMS Technical Documentation
DC Cable SCB-3
The DC Cable SCB-3 is used to connect the Service Battery to the
charger connection Vin of the phone when doing the charger calibration
service procedure.
Product Code
DC Cable SCB-3:0730114
View of SCB-3
Page 12
Nokia Mobile Phones Ltd.
Issue 1 08/99
Page 13
PAMS Technical Documentation
Power Cable PCS-1
The Power Cable PCS-1 is used to connect the module jigs JBT-1 and
JBS-19 to an external power supply.
Product Code
Power Cable PCS-1:0730012
View of PCS-1
THF–13
Service Tools
Issue 1 08/99
Nokia Mobile Phones Ltd.
Page 13
Page 14
THF–13
Service Tools
External Antenna Cable XRC-1B
The External Antenna Cable is used to connect the transceiver to
measuring equipment during servicing.
Note: Typical attenuation at 900 MHz is 0.7 dB.
Typical attenuation at 1800 MHz is 0.9 dB.
Product Code
External Antenna Cable XRC-1B:0730128
View ofXRC-1B
PAMS Technical Documentation
Page 14
Nokia Mobile Phones Ltd.
Issue 1 08/99
Page 15
PAMS Technical Documentation
Modular T-adapter
The modular T-adapter is a suitable branching unit to provide the needed
parallel modular connections.
Product Code
Modular T-adapter:4626134
View of Modular T-adapter
THF–13
Service Tools
SW Security Device PKD-1
SW security device is a piece of hardware enabling the use of the service
software when connected to the parallel (LPT) port of the PC. Whitout the
dongle present it is not possible to use the service software. Printer or any
such device can be connected to the PC through the dongle if needed.
Caution: Make sure thet you have switched off the PC and the printer
before making connections!
Caution: Do not connected the PKD-1 to the serial port. You may
damage your PKD-1!
Product Code
SW Security Device PKD-1:0750018
View of SW Security Device
Issue 1 08/99
Nokia Mobile Phones Ltd.
Page 15
Page 16
THF–13
Service Tools
Fast T ravel Charger ACH-6
Operating within the voltage range 90 V...250 V AC (50 Hz...60 Hz), the Fast
Travel Charger is practically current independent in normal use.