Nokia Lumia 800, RM-801, RM-819 Service Manual

Service Manual for L1 and L2

Nokia Lumia 800

RM-801, RM-819

Key features

Windows Phone Mango operating system
Large 3.7" OLED ClearBlack screen
Best instant social experience
Sync, store and share media files
Fast browsing with IE9

Version 2.0

Exploded view Disassembly steps Disassembly video

Check the repair

policy before

performing any

mechanical repair

on Service Level

1&2!

More More More

Assembly steps Assembly video Service devices

More More More

Product controls and interfaces Service concept Phone reset

More More More

©2011 Nokia | Confidential | All Rights Reserved.

Service Manual Level 1 and 2

Nokia Lumia 800

RM-801, RM-819
Version 2.0

DISPLAY ASSEMBLY

(I0004, I0005)

DISPLAY

I0004

Exploded view

WINDOW FRAME
I0005

ALS PROXIMITY FPC

SCREW TORX+

SIZE 5 M1.4 X 1.7

LIGHT SWAP PACKAGE

(I0011 - I0029)

2

EARPIECE BOOT

SHIELDING COVER 2

LIGHT SWAP PWB

THERMAL PAD

THERMALPAD

SHIELDING COVER 1

I0006

I0003

TYPE LABEL

I0027

SIM DOOR

I0002

USB DOOR

I0001

BTB RUBBER

I0012

I0028

EARPIECE

I0029

I0020

I0011

I0023

I0022

I0019

FLASH BOOT

I0026

SCREW TORX+
SIZE 5 M1.4 X 3.6
I0007

CHASSIS
I0008

BATTERY
I0009

BATTERY SPONGE
I0010

BTB RUBBER
I0014

BTB RUBBER
I0013
BTB RUBBER
I0015

SHIELDING COVER 4
I0021

THERMAL PAD
I0018

THERMAL PAD
I0018

THERMAL PAD
I0025

SHIELDING COVER 7
I0017

THERMAL PAD
I0024

SHIELDING COVER 8
I0016

BODY ASSEMBLY

(I0031 - I0036)

3

CAMERA MODULE

I0030

SIDE KEY FLEX

I0031

AV FLEX

I0032

TYPE LABEL 2

I0027

Only available
as assembly

©2011 Nokia | Confidential | All Rights Reserved.

ANTENNA
I0034

IHF SPEAKER
I0033

BODY
I0036

FLASH MODULE

Not reuseable
after removal

Repair/swap
only in level 3

Service Manual Level 1 and 2

Nokia Lumia 800

RM- 801, RM -819
Version 2.0

Disassembly steps

For disassembling you need the Nokia Standard toolkit version 2. You will also need the camera removal
tool SS-210 and the unibody opening tool SS-282.

Protect the DISPLAY with protective film.

Push in from the shown place to open the USB DOOR.

Pull the SIM DOOR to the direction shown to open it.

Remove the SIM DOOR.

Pull out and remove the USB DOOR. Do not use it again. Discard it.

Unscrew the two Torx+ size 5 screws in the order shown. Do not use them again. Discard them.

Insert the unibody opening tool SS-282 to the shown place and lever up the top left corner of the
WINDOW FRAME.

Insert the SS-282 to the shown place and lever up the top right corner of the WINDOW FRAME.

Release the left side of the WINDOW FRAME by sliding the SRT-6 to the direction shown. Start from the
top end of the device. While releasing the WINDOW FRAME, be careful not to damage the BODY
ASSEMBLY.

Release also the right side of the WINDOW FRAME by sliding the SRT-6 to the direction shown. Start from
the top end of the device.

Pull the WINDOW FRAME gently to the direction shown to release the three remaining clips holding it.

Turn over the WINDOW FRAME as shown. While turning the WINDOW FRAME, be careful not to damage the
two shown flexes.

Use the SS-93 to open the DISPLAY connector. While opening the connector, be careful not to damage it
or nearby components.

Use the sharp end of the SS-93 to open the PROXIMITY connector. While opening the connector, be
careful not to damage it or nearby components.

The WINDOW FRAME can now be separated.

Remove the PROXIMITY flex by pulling it with fingers. Do not use it again. Discard it.

Unscrew the six Torx+ size 5 screws in the order shown. Do not use them again. Discard them.

Lift the CHASSIS up from the shown place. While removing the CHASSIS, be careful not to bend it.

Carefully pull the BODY ASSEMBLY to the direction shown to release the left side of the CHASSIS.

Pull the CHASSIS to the direction shown to remove it.

Lift up the BATTERY from the battery compartment.

Use the SS-93 to open the BATTERY connector. Be careful not to damage the BATTERY connector or the
components nearby.

The BATTERY can now be separated.

Remove the BATTERY SPONGE with tweezers. Do not use it again. Discard it.

Open the shown connector with the SS-93. Be careful not to damage the connector or any nearby
components.

Open the shown connector with the SS-93. Be careful not to damage the connector or any nearby
components.

Open the shown connector with the SS-93. Be careful not to damage the connector or any nearby
components.

Lift up the ENGINE BOARD from the bottom end.

Carefully pull out and remove the BODY ASSEMBLY.

Remove the EARPIECE BOOT with tweezers.

Release the EARPIECE with the dental tool. Be careful not to injure yourself or the ENGINE BOARD with
the sharp end of the dental tool.

Remove the EARPIECE with tweezers. Do not use it again. Discard it.

Place the SS-210 on top of the CAMERA and push down the metal sheets to unlock the camera retaining
clips. Lift up and remove the CAMERA.

Use tweezers to remove the FLASH BOOT. Be careful not to damage the ENGINE BOARD or the two pins
while removing the FLASH BOOT. Do not use the FLASH BOOT again. Discard it.

The Nokia Lumia 800 disassembly procedure is complete.

-END OF DISASSEMBLY-

©2011 Nokia

Service Manual Level 1 and 2

Nokia Lumia 800

RM- 801, RM -819
Version 2.0

Assembly steps

For assembling you need the Nokia Standard Toolkit version 2.

Remove the protective tape from the FLASH BOOT.

Place the FLASH BOOT as shown to the ENGINE BOARD. Press it gently from the shown places with the
SS-93. Be careful not to damage the springs!

Place the CAMERA so that the guiding pin is aligned correctly.

Press the CAMERA to its place gently with the SS-93.

Remove the EARPIECE from its packaging with tweezers.

When placing the EARPIECE, check that the pins are aligned correctly.

Place the EARPIECE to its place and gently push to attach it.

Remove the EARPIECE protective film.

Place the EARPIECE BOOT with tweezers and press it gently to attach it to the EARPIECE.

Push in the top part of the ENGINE BOARD to the BODY ASSEMBLY as shown. Check that the USB
connector is correctly aligned.

Lower down the bottom end of the ENGINE BOARD. Be careful not to damage the three shown
connectors!

Use the SS-93 to connect the three shown connectors. Be careful not to damage the connectors or any
components nearby!

Remove the BATTERY SPONGE protective tape.

Carefully attach the BATTERY SPONGE to the BATTERY connector as shown. Check that the BATTERY
SPONGE is aligned correctly.

Insert the BATTERY to the battery compartment bottom end first.

Connect the BATTERY connector with the SS-93. Be careful not to damage the connector or
components nearby.

Place the bottom end of the CHASSIS to the BODY ASSEMBLY as shown and lower down the top end of
the CHASSIS.

Press the CHASSIS gently so that it snaps to its place.

Tighten the six Torx+ size 5 screws to the torque of 12 Ncm in the order shown.

Remove the two PROXIMITY FLEX protective tapes.

Place the PROXIMITY FLEX as shown. Activate the PROXIMITY FLEX adhesive by pressing from the shown
places gently with the SS-93. Be careful not to damage the PROXIMITY FLEX!

Hold the WINDOW FRAME as shown and connect the PROXIMITY connector and the DISPLAY connector
with the SS-93. Be careful not to damage the connectors!

Lower down the bottom end of the WINDOW FRAME and push it to the BODY ASSEMBLY as shown.

Press the WINDOW FRAME from all sides to attach it to the BODY ASSEMBLY. Start from the right side of
the device.

Remove the protective film from the top end of the device.

Tighten the two Torx+ size 5 screws to the torque of 9 Ncm in the order shown.

Push the USB DOOR into its place. Hold the USB DOOR firmly when pushing it in, so that it does not bend.

Push the SIM DOOR in and close the USB DOOR.

Remove the DISPLAY protective film.

Remove the protective film from the volume keys, the power key and from the camera key.

Remove the BODY ASSEMBLY protective film.

Remove the CAMERA protective film.

The Nokia Lumia 800 assembly procedure is complete.

-END OF ASSEMBLY-

©2011 Nokia

Service Manual Level 1 and 2

Nokia Lumia 800

RM- 801, RM -819
Version 2.0

CA-101 Service cable AC-16 Travel charger SS-210 Camera removal tool

Service devices

SS-282 Unibody opening tool

Nokia Standard Toolkit (v2)

For more information, refer to the Service

Bulletin (SB-011) on Nokia Online. Supplier or

manufacturer contacts for tool re-order can

be found in “Recommended service

equipment” document on Nokia Online.

©2011 Nokia | Confidential | All Rights Reserved.

Service Manual Level 1 and 2

Nokia Lumia 800

RM-801, RM-819
Version 2.0

Product controls and interfaces

1
2

7

10

11

3

4

5

1 — Nokia AV 3.5 mm connector

2 — Micro USB connector

3 — Micro SIM card holder

4 — Earpiece

5 — Ambient light & proximity

sensor

6 — Touch screen

6

7 — Back key

8 — Start key

9 — Search key

10 — Microphone

8

9

11 — Loudspeaker

12 — Camera flash

13 — Camera

14 — Volume keys

15 — Power/Lock key

16 — Camera key

12

13

14

14

15

16

©2011 Nokia | Confidential | All Rights Reserved.

Service Manual Level 1 and 2

Nokia Lumia 800

RM-801, RM-819
Version 2.0

Flashing concept

Service

software

Service concept

CA-101

Note: Charged
battery is man­datory

On Device Diagnostics Tool (ODDT)

The ODDT is an app for performing basic device hardware
troubleshooting at Nokia Care Points. The ODDT is not visible on
retail phones and it is intended only for use by trained personnel at
Nokia Care Points.

To install the ODDT:

1. Enter ##634# on the on-screen keypad

2. Diagnostics app appears in Apps list

To remove the ODDT:

1. Tap and hold Diagnostics

2. Tap uninstall

Note: always uninstall the tool before returning the phone to the
consumer!

Transceiver with

embedded battery

For more information on using the ODDT, see KICS TR2816.

©2011 Nokia | Confidential | All Rights Reserved.

Service Manual Level 1 and 2

Nokia Lumia 800

RM- 801, RM -819
Version 2.0

Phone reset

Hardware reset

If the phone hardware is jammed, you should first recommend
that the consumer performs a hardware reset. The hardware
reset does not reset the Windows Live ID or remove any
consumer data. Because the consumer cannot remove the
battery to reset the phone the phone has a special electronic
circuit which cuts the phone power when the power key is
pressed for 10 seconds.

To perform the hardware reset press the Power key and hold it
for 10 seconds. The phone screen will turn black (phone is off).
Then press the Power key to turn on the phone.

Software / operating system (OS) reset

The software / operating system (OS) reset returns the phone to its out-of-the-box state. Note that
this procedure erases all consumer data! Always first try to perform a hardware reset.

Option 1: About menu

- Use this option if the consumer knows the lock code

- This option warns the consumer about data loss!

- Tap Settings > About > reset your phone

Option 2: Hardware key combination

- Use this option if the phone is locked and the consumer does not know the code

- Note: no warning about data loss!

- Do not advertise this feature to consumers!

Follow next steps to perform OS reset with phone keys.

Step 1
Make sure the phone is turned
Off. Press and hold the Volume
down, Power and Camera keys

Step 2
When the phone vibrates release
the Power key

Step 3
Keep holding the Volume down
and Camera keys for another 5
seconds and then release the keys

Step 4
The phone will reset and boot up
automatically

©2011 Nokia

Service Manual Level 1 and 2

Nokia Lumia 800

RM- 801, RM -819
Version 2.0

Version Date Description

1.0 26.10.2011 First published version

2.0 11.11.2011 Added Exploded view, Disassembly steps, Disassembly video, Assembly steps, Assembly

Version history

video and Service devices

©2011 Nokia | Confidential | All Rights Reserved.