Nokia RM-57, RM-58 Service Manual

Nokia Customer Care

Service Manual

RM-57/58 (Nokia 6681/6682)

Mobile Terminal

Part No: 9239169 (Issue 1)

Company Confidential

RM-57/58

Nokia Customer Care Amendment Record Sheet

Amendment Record Sheet

Amendment No Date Inserted By Comments

Issue 1 04/2005 J-AK

Page ii Company Confidential Issue 1

RM-57/58 Copyright Nokia Customer Care

Copyright

the prior written permission of Nokia is prohibited. Nokia, Nokia Connecting People, and Nokia X and Y are trademarks or registered trademarks of Nokia

Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.

Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice.

Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.

The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at any time without prior notice.

The availability of particular products may vary by region.

IMPORTANT

This document is intended for use by qualified service personnel only.

Issue 1 Company Confidential Page iii

RM-57/58

Nokia Customer Care Warnings and cautions

Warnings and cautions

Warnings

• IF THE DEVICE CAN BE INSTALLED IN A VEHICLE, CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS AND ANTI-SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF NECESSARY, CONSULT THE VEHICLE DEALER/ MANUFACTURER TO DETERMINE THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF ENERGY.

• THE PRODUCT MUST NOT BE OPERATED IN AREAS LIKELY TO CONTAIN POTENTIALLY EXPLOSIVE ATMOSPHERES, FOR EXAMPLE, PETROL STATIONS (SERVICE STATIONS), BLASTING AREAS ETC.

• OPERATION OF ANY RADIO TRANSMITTING EQUIPMENT, INCLUDING CELLULAR TELEPHONES, MAY INTERFERE WITH THE FUNCTIONALITY OF INADEQUATELY PROTECTED MEDICAL DEVICES. CONSULT A PHYSICIAN OR THE MANUFACTURER OF THE MEDICAL DEVICE IF YOU HAVE ANY QUESTIONS. OTHER ELECTRONIC EQUIPMENT MAY ALSO BE SUBJECT TO INTERFERENCE.

• BEFORE MAKING ANY TEST CONNECTIONS, MAKE SURE YOU HAVE SWITCHED OFF ALL EQUIPMENT.

Cautions

• Servicing and alignment must be undertaken by qualified personnel only.

• Ensure all work is carried out at an anti-static workstation and that an anti-static wrist strap is worn.

• Ensure solder, wire, or foreign matter does not enter the telephone as damage may result.

• Use only approved components as specified in the parts list.

• Ensure all components, modules, screws and insulators are correctly re-fitted after servicing and alignment. Ensure all cables and wires are repositioned correctly.

Use only approved components as specified in the parts list.

• Never test a mobile phone WCDMA transmitter with full Tx power, if there is no possibility to perform the measurements in a good performance RF-shielded room. Even low power WCDMA transmitters may disturb nearby WCDMA networks and cause problems to 3G cellular phone communication in a wide area.

• During testing never activate the GSM or WCDMA transmitter without a proper antenna load, otherwise GSM or WCDMA PA may be damaged.

Page iv Company Confidential Issue 1

RM-57/58 ESD protection Nokia Customer Care

ESD protection

Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone.

Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use.

To replace the covers ESD protection must be applied. All electronic parts of the product are susceptible to ESD. Resistors, too, can be damaged by static electricity

discharge. All ESD sensitive parts must be packed in metallized protective bags during shipping and handling outside any

ESD Protected Area (EPA). Every repair action involving opening the product or handling the product components must be done under

ESD protection. ESD protected spare part packages MUST NOT be opened/closed out of an ESD Protected Area. For more information and local requirements about ESD protection and ESD Protected Area, contact your local

Nokia After Market Services representative.

Issue 1 Company Confidential Page v

RM-57/58

Nokia Customer Care Care and maintenance

Care and maintenance

This product is of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years.

• Keep the phone and all its parts and accessories out of the reach of small children.

• Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that

will corrode electronic circuits.

• Do not use or store the phone in dusty, dirty areas. Its moving parts can be damaged.

• Do not store the phone in hot areas. High temperatures can shorten the life of electronic devices, damage

batteries, and warp or melt certain plastics.

• Do not store the phone in cold areas. When it warms up (to its normal temperature), moisture can form

inside, which may damage electronic circuit boards.

• Do not drop, knock or shake the phone. Rough handling can break internal circuit boards.

• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the phone.

• Do not paint the phone. Paint can clog the moving parts and prevent proper operation.

• Use only the supplied or an approved replacement antenna. Unauthorised antennas, modifications or

attachments could damage the phone and may violate regulations governing radio devices.

All of the above suggestions apply equally to the product, battery, charger or any accessory.

Page vi Company Confidential Issue 1

RM-57/58 Company Policy Nokia Customer Care

Company Policy

Our policy is of continuous development; details of all technical modifications will be included with service bulletins.

While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any errors are found by the reader, NOKIA MOBILE PHONES Business Group should be notified in writing/e-mail.

Please state:

• Title of the Document + Issue Number/Date of publication

• Latest Amendment Number (if applicable)

• Page(s) and/or Figure(s) in error

Please send to:

NOKIA CORPORATION Nokia Mobile Phones Business Group Nokia Customer Care PO Box 86 FIN-24101 SALO Finland E-mail: Service.Manuals@nokia.com

Issue 1 Company Confidential Page vii

RM-57/58

Nokia Customer Care Battery information

Battery information

Note: A new battery's full performance is achieved only after two or three complete charge and

discharge cycles!

The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.

Use only batteries approved by the phone manufacturer and recharge the battery only with the chargers approved by the manufacturer. Unplug the charger when not in use. Do not leave the battery connected to a charger for longer than a week, since overcharging may shorten its lifetime. If left unused a fully charged battery will discharge itself over time.

Temperature extremes can affect the ability of your battery to charge. For good operation times with Ni-Cd/NiMh batteries, discharge the battery from time to time by leaving the

product switched on until it turns itself off (or by using the battery discharge facility of any approved accessory available for the product). Do not attempt to discharge the battery by any other means.

Use the battery only for its intended purpose. Never use any charger or battery which is damaged. Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object (coin, clip or pen)

causes direct connection of the + and - terminals of the battery (metal strips on the battery) for example when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage the battery or the connecting object.

Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and lifetime of the battery. Always try to keep the battery between 15°C and 25°C (59°F and 77°F). A phone with a hot or cold battery may temporarily not work, even when the battery is fully charged. Batteries' performance is particularly limited in temperatures well below freezing.

Do not dispose of batteries in a fire! Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste.

Page viii Company Confidential Issue 1

RM-57/58 Nokia 6681/6682 Service Manual Structure Nokia Customer Care

Nokia 6681/6682 Service Manual Structure

1 General Information 2 Parts Lists and Component Layouts 3 Service Software Instructions 4 Service Tools and Service Concepts 5 Disassembly/Reassembly Instructions 6 BB Troubleshooting and Manual Tuning Guide 7 RF Troubleshooting and Manual Tuning Guide 8 Camera Module Troubleshooting 9 System Module 10 Schematics

Issue 1 Company Confidential Page ix

RM-57/58

Nokia Customer Care Nokia 6681/6682 Service Manual Structure

(This page left intentionally blank.)

Page x Company Confidential Issue 1

Nokia Customer Care

1 — General Information

Issue 1 Company Confidential Page 1–1

RM-57/58

Nokia Customer Care General Information

(This page left intentionally blank.)

Page 1–2 Company Confidential Issue 1

RM-57/58 General Information Nokia Customer Care

Table of Contents

RM-57/58 product selection.........................................................................................................................................................1–5

Product features and sales package.........................................................................................................................................1–5

Product and module list................................................................................................................................................................1–6

Mobile enhancements...................................................................................................................................................................1–7

Technical specifications................................................................................................................................................................1–8

Transceiver general specifications......................................................................................................................................1–8

Main RF characteristics for triple-band (EGSM900/1800/1900 and GSM850/1800/1900) phones..................1–8

Battery endurance....................................................................................................................................................................1–9

Environmental conditions......................................................................................................................................................1–9

List of Tables

Table 1 Audio....................................................................................................................................................................................1–7

Table 2 Car.........................................................................................................................................................................................1–7

Table 3 Carrying...............................................................................................................................................................................1–8

Table 4 Data......................................................................................................................................................................................1–8

Table 5 Imaging ..............................................................................................................................................................................1–8

Table 6 Messaging...........................................................................................................................................................................1–8

Table 7 Power...................................................................................................................................................................................1–8

List of Figures

Figure 1 View of RM-57..................................................................................................................................................................1–5

Issue 1 Company Confidential Page 1–3

RM-57/58

Nokia Customer Care General Information

(This page left intentionally blank.)

Page 1–4 Company Confidential Issue 1

RM-57/58 General Information Nokia Customer Care

RM-57/58 product selection

Nokia RM-57 is a tripleband handportable phone, supporting EGSM900/1800/1900 bands (RM-58: GSM850/1800/

1900). According to GSM standard 05.05 it responds to class 4 (max. 2W) in EGSM900 (RM-58: GSM850 Power class 4

(2W)), class 1 (1W) in GSM 1800 and class 1 in GSM 1900. The device supports EGPRS (EDGE) class B as well as Bluetooth 1.2 standard. The handset has a full phase 2 Type Approval and it complies with the GSM Type Approval. It also has a full CE approval and FCC approval.

The device is an MMS (Multimedia Messaging Service) enabled phone with a large bright color display and an integrated 1.3 megapixel (effective image size 1.23 megapixel) camera.

The MMS implementation follows the OMA MMS standard release 1.2. WAP 2.0 compatible browser supports XHTML Mobile Profile (MP) and uses a TCP/IP stack to communicate with

a gateway in network. The operating system is Symbian 8.0a, also supporting MIDP Java 2.0 & CLDC1.1, which provides a good platform

for 3rd party applications.

Figure 1 View of RM-57

Product features and sales package

Imaging

• Integrated 1.3 (effective 1.23) megapixel camera (1280 x 960 pixels) with smooth 6 x digital zoom and camera activation and control slide

• Integrated Flash LED

• Active TFT colour display, 176 x 208 pixels, 262k colours

• 10 MB on-board user memory Hot swap reduced size memory card slot

• Camcorder, still imaging and video call

• Video and still image editors

Issue 1 Company Confidential Page 1–5

RM-57/58

Nokia Customer Care General Information

• Image and video upload to the web

• USB printing (Pictbridge)

Bearers and transport

• GSM triband phone (RM-57: EGSM900/1800/1900, RM-58: GSM850/1800/1900) EGPRS (class B, Multislot class

10) (Max DL=236.8 kbps UL=118.4 kbps )

Software platform

• SW platform: Nokia Series 60 rel 2.6

Connectivity

• Bluetooth (Headset & Handsfree profiles, BIP, GOP)

• RS (Half Size) MMC Card 64 MB

• Pop-Port™ interface with USB

• PC Suite connectivity with USB & Bluetooth

Productivity

• SMS, MMS and email

• MS Word, PowerPoint and Excel viewers

• PIM (Calendar & Contacts)

• Internet browser

• Video streaming (3GPP)

• Push to Talk

• Logs (last calls , timers and history list)

• Instant messaging

•

JavaTM MIDP 2.0, CLDC 1.13D API, PIM API, File access API

• MP3

• Data Transfer

• Settings Wizard/Access Point Configurator

Sales package

• Transceiver RM-57/58

• BL-5C Li-ion Battery

• ACP-12x Charger

• All-in-one User Guide (warranty card + accessory info + getting started sheet + invitational module for Club Nokia )

• CD-ROM (with PC-Suite and User Guide)

• Stereo Headset HDS-3 (APAC & Latin America: HS-3, China HS-27R)

• USB Cable DKU-2

• RS-MMC 64 MB with adapter

• MMC/SD card reader (EMEA)

• Wrist strap

Product and module list

Module name Type code Notes

System/RF Module 1LF Main PWB with components

Page 1–6 Company Confidential Issue 1

RM-57/58 General Information Nokia Customer Care

Module name Type code Notes

UI Module 1HV Keyboard PWB with components.

Part of the UI Frame Assy

Camera Module Mirage-1.3X

Display Module

Chassis Assy Mechanical Assembly

UI Frame Assy Mechanical Assembly

SW Module

Mobile enhancements

Table 1 Audio

Enhancement Type

Boom mono headset HDB-4

Stereo headset HDS-3

Mono headset HS-5

Fashion stereo headset HS-3

Wireless clip-on headset HS-21W

Wireless boom headset HS-4W

Wireless headset HDW-3

Wireless headset HS-11W

Wireless image headset HS-13W

Inductive loopset LPS-4

FM radio headset HS-27R

Music stand MD-1

Audio adapter AD-15

TTY adapter HDA-10

Table 2 Car

Enhancement Type

Mobile charger LCH-12

Wireless car kit CK-1W

Advanced car kit CK-7W

Plug-in car handsfree HF-3

Headrest handsfree BHF-3

Car kit CK-10

Mobile holder CR-27

Issue 1 Company Confidential Page 1–7

RM-57/58

Nokia Customer Care General Information

Table 3 Carrying

Enhancement Type

Carrying case CNT-676

Table 4 Data

Enhancement Type

USB data cable DKU-2

RS multimedia card 64 MB MU-1

RS multimedia card 128 MB MU-2

Wireless GPS module LD-1W

Table 5 Imaging

Enhancement Type

Image album PD-1

Remote camera PT-6

Table 6 Messaging

Enhancement Type

Nokia digital pen SU-1B

Wireless keyboard SU-8W

Table 7 Power

Enhancement Type

Battery 900mAh Li-ion BL-5C

Travel charger ACP-12

Retractable charger AC-1

Technical specifications

Transceiver general specifications

Unit Dimensions (L x W x T) Weight (g)

Volume (cm3)

Transceiver with BL-5C 900mAh li-ion battery back

108.4 x 55.2 x 20.5 133 (including BL-5C battery)

104

Main RF characteristics for triple-band (EGSM900/1800/1900 and GSM850/1800/1900) phones

Parameter Unit

Cellular systems EGSM900, GSM1800/1900 and GSM850/1800/1900

Page 1–8 Company Confidential Issue 1

RM-57/58 General Information Nokia Customer Care

Parameter Unit

Rx frequency band GSM850: 869 - 894

EGSM900: 925 - 960 MHz

GSM1800: 1805 - 1880 MHz

GSM1900: 1930 - 1990 MHz

Tx frequency band GSM850: 824 - 849 MHz

EGSM900: 880 - 915 MHz

GSM1800: 1710 - 1785 MHz

GSM1900: 1850 - 1910 MHz

Output power GSM850: +5...+33 dBm/3.2 mW...2W

EGSM900: +5 … +33dBm/3.2mW … 2W

GSM1800: +0 … +30dBm/1.0mW … 1W

GSM1900: +0 … +30dBm/1.0mW … 1W

Number of RF channels GSM850: 124

EGSM900: 125

GSM1800: 375

GSM1900: 300

Channel spacing 200 kHz

Number of Tx power levels GSM850, EGSM900: 15

GSM1800, GSM1900: 16

Battery endurance

Battery Capacity (mAh) Talk time Stand-by

BL-5C 900 up to 3-6 hrs* up to 6 - 11 days*

Note: *Depends on the operator network configuration used.

Charging times

ACP-12 LCH-12

1h 15min 1h 15min

Environmental conditions

Environmental condition Ambient temperature Notes

Normal operation

Reduced performance

Issue 1 Company Confidential Page 1–9

-15oC...+55oC

-25oC...-15oC

+55oC...+70oC

Specifications fulfilled

Operational for shorts periods only

RM-57/58

Nokia Customer Care General Information

Environmental condition Ambient temperature Notes

Intermittent operation

No operation or storage

Charging allowed

Long term storage conditions

-40oC...-15oC

+70oC...+85 oC

<-40oC...>+85oC

-25oC...+50oC

0oC...+85oC

Operation not guaranteed but an attempt to operate does not damage the phone.

No storage or operation: an attempt may damage the phone.

Page 1–10 Company Confidential Issue 1

Nokia Customer Care

2 — Parts Lists and Component

Layouts

Issue 1 Company Confidential Page 2–1

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

(This page left intentionally blank.)

Page 2–2 Company Confidential Issue 1

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Table of Contents

RM-57/58 exploded view..............................................................................................................................................................2–5

Spare parts overview.....................................................................................................................................................................2–6

Parts lists............................................................................................................................................................................................2–7

Mechanical spare parts list.....................................................................................................................................................2–7

RM-57 component parts list (1LF_09a)...............................................................................................................................2–8

Variant parts for RM-58.........................................................................................................................................................2–38

Component layouts......................................................................................................................................................................2–39

Component layout - bottom (1LF_09a)............................................................................................................................2–39

Component layout - top (1LF_09a)....................................................................................................................................2–39

Issue 1 Company Confidential Page 2–3

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

(This page left intentionally blank.)

Page 2–4 Company Confidential Issue 1

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

RM-57/58 exploded view

Issue 1 Company Confidential Page 2–5

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Spare parts overview

Page 2–6 Company Confidential Issue 1

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Parts lists

Mechanical spare parts list

• Bold = assembly (assy)

• I0xx = ITEM codes for upper or mono block

• I1xx = ITEM codes for hinge block

• I2xx = ITEM codes for lower block

• I3xx = ITEM codes for soldered spare parts in the upper hinge or lower block and not exchangeable

Note: For Nokia product codes, please refer to the latest Service Bulletins on the Partner Website (PWS).

To ensure you are always using the latest codes, please check the PWS on a daily basis.

GSM antenna I042 has the same item reference in RM-57 and RM-58 but different product codes. See Variant

parts for RM-58 (Page 2–38)

ITEM/ CIRCUIT REF. QTY PART NAME

I001 1 A-COVER ASSY

I002 1 KEYMAT

I003 7 SCREW M1.8X9

I004 1 DISPLAY SHIELD ASSY

I005 1 DISPLAY

1 UI FRAME ASSY (I006-I012)

I006 1 DOMESHEET

I007 1 UI PWB

I008 1 UI PWB ADHESIVE

I009 1 UI FRAME

I010 1 BB SHIELD

I011 1 EARPIECE GASKET

I012 1 EARPIECE

I013 1 ENGINE MODULE

I014 1 CAMERA MODULE 1.3 MP

1 FLASH SHIELDING ASSY

I015 1 FLASH SHIELDING LID ASSY

I016 1 FLASH SHIELDING FRAME

1 BLUETOOTH SHIELDING ASSY

I017 1 BLUETOOTH SHIELDING LID ASSY

I018 1 BLUETOOTH SHIELDING FRAME

1 RF ENGINE SHIELDING ASSY

I019 1 RF ENGINE SHIELDING LID ASSY

Issue 1 Company Confidential Page 2–7

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

ITEM/ CIRCUIT REF. QTY PART NAME

I020 1 RF ENGINE SHIELDING FRAME

1 GSM PA SHIELDING ASSY

I021 1 GSM PA SHIELDING LID ASSY

I022 1 GSM PA SHIELDING FRAME

1 FLASH CAN SHIELDING ASSY

I023 1 FLASH CAN SHIELDING LID ASSY

I024 1 FLASH CAN SHIELDING FRAME

1 CHASSIS ASSY (I025-I044)

I025 1 POWER KEY

I026 1 MMC DOOR

I027 1 MMC DOOR SPRING

I028 1 BLUETOOTH ANTENNA

I029 1 MICROPHONE

I030 1 DC JACK

I031 1 VIBRA MOTOR

I032 1 VOICE KEY

I033 1 IHF SPEAKER

I034 1 IHF GAUZE

I035 1 IHF SUPPORT FOAM

I036 1 CHASSIS AUDIO ASSY

I037 1 LOCKING SPRING

I038 1 LED FLASH HOLDER

I039 1 LED FLASH CONNECTOR

I040 1 LED FLASH

I041 1 SLIDE SENSOR

I042 1 GSM ANTENNA

I043 1 CARD PLATE INCL. GROUND GASKET

I044 1 TYPE LABEL

I045 1 ANTENNA -COVER

I046 1 B-COVER ASSY

RM-57 component parts list (1LF_09a)

Note: Antenna switch Z7503 and SAW filter Z7504 have the same reference in RM-57 and RM-58 but

different product codes. See Variant parts (Page 2–38).

Page 2–8 Company Confidential Issue 1

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

For Nokia product codes, please refer to the latest Service Bulletins on the Partner Website (PWS). To ensure you are always using the latest codes, please check the PWS on a daily basis.

BTM = Bottom

Item Side Grid reference Description and Value Type

FLASH CAN ASSEMBLY

A1470 BTM ~I 10

A3000 BTM ~C 7

A6000 BTM ~C 4

A7000 BTM ~F 12

040003354 ~ ~

FLASH CAN DMC07004 RM-1 ~ ~

BT CAN DMC07003 RM-1 ~ ~

RF ENGINE CAN DMC07006 RM-1 ~ ~

SHIELD_04 0_003354

SHIELD_DM C07004

SHIELD_DM C07003

SHIELD_DM C07006

A7001 BTM ~I 15

A7002 BTM ~C 18

A7003 BTM ~I 13

B2200 Top ~D 3

C1470 BTM ~F 18

C1471 BTM ~F 15

WDCMA PA CAN DMC07007 RM-1 ~ ~

GSM PA CAN DMC07005 RM-1 ~ ~

VCO CAN DMD11427 RM-1 ~ ~

CRYSTAL

32.768KHZ +-20PPM

12.5PF 32.768kHz ~

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

SHIELD_DM C07007

SHIELD_DM C07005

SHIELD_DM D11427

CRYSTAL_3. 3X1.6NR

CHIPCAP X5R 1U K

C1472 BTM ~D 8

Issue 1 Company Confidential Page 2–9

6V3 0603 1u0 6.3V 0603C

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

CHIPCAP X5R 1U K

C1473 BTM ~D 8

C1483 Top ~J 3

C1484 BTM ~H 10

C1485 BTM ~H 11

C1486 BTM ~I 11

6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

CHIPCAP X5R 4U7 K 6V3 0805 4u7 6V3 0805C

CHIPCAP 2U2 K 25V 1206 2u2 25V

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

1206C_H1. 8

C1487 BTM ~K 11

C1488 BTM ~J 11

C2000 BTM ~J 4

C2002 BTM ~E 3

C2003 Top ~E 2

C2004 Top ~D 2

C2005 Top ~E 2

C2006 Top ~E 2

Chipcap 5% NP0 10p 50V 0402C

Chipcap 5% NP0 27p 50V 0402C

CHIPCAP X5R 2U2 K 6V3 0603 2u2 6V3 0603C

CERCAP X7R 22N K 16V 0402 22n 16V 0402C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

Chipcap X7R 10%

C2007 Top ~D 2

C2008 Top ~D 2

Page 2–10 Company Confidential Issue 1

16V 0402 10n 16V 0402C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

Chipcap X7R 10%

C2009 Top ~D 2

C2010 Top ~D 1

C2011 BTM ~F 3

C2012 BTM ~J 3

C2070 BTM ~G 2

C2071 BTM ~I 3

16V 0402 10n 16V 0402C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

CHIPCAP NP0 270P J 25V 0402 270p 25V 0402C

CHIPCAP X5R 1U K 25V 0603 1u0 25V 0603C

Chipcap 5% NP0 15p 50V 0402C

CHIPTCAP 100U M 14V 6X3.2X2 100u_14V 14V

TANT_6.3X

3.5_H2.0

C2072 BTM ~I 3

C2100 Top ~E 2

C2101 Top ~E 2

C2102 Top ~E 2

C2103 Top ~D 2

C2104 Top ~D 2

C2105 Top ~F 2

C2106 Top ~F 2

Chipcap 5% NP0 15p 50V 0402C

CHIPCAP X7R 15N K 16V 0402 15n 16V 0402C

CHIPCAP X5R 2U2 K 6V3 0603 2u2 6V3 0603C

Chipcap 5% X7R 1n0 50V 0402C

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

Chipcap X7R 10%

C2107 Top ~G 2

Issue 1 Company Confidential Page 2–11

50V 0402 1n0 50V 0402C

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

Chipcap X7R 10%

C2108 Top ~G 2

C2109 Top ~G 2

C2110 Top ~G 2

C2200 Top ~E 2

C2201 Top ~D 4

C2202 Top ~D 3

50V 0402 1n0 50V 0402C

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

C2203 Top ~D 3

C2204 Top ~D 3

C2205 Top ~D 3

C2206 Top ~D 3

C2207 Top ~D 4

C2208 Top ~D 4

C2209 Top ~D 4

C2210 Top ~F 4

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

Chipcap 5% NP0 27p 50V 0402C

Chipcap 5% NP0 22p 50V 0402C

CHIPCAP X5R 1U K 16V 0603 1u0 16V 0603C

CHIPCAP X5R 4U7 K

C2211 Top ~G 3

Page 2–12 Company Confidential Issue 1

10V 0805 4u7 10V 0805C

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

CHIPCAP X5R 1U K

C2212 Top ~F 3

C2213 Top ~D 5

C2214 Top ~E 4

C2215 Top ~F 4

C2216 Top ~E 4

C2217 Top ~D 5

6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

C2219 Top ~D 4

C2220 Top ~F 4

C2221 Top ~F 4

C2222 Top ~F 4

C2223 Top ~D 2

C2224 Top ~E 5

C2225 Top ~D 4

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 1U K

C2226 Top ~F 3

Issue 1 Company Confidential Page 2–13

6V3 0603 1u0 6.3V 0603C

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

CHIPCAP X5R 1U K

C2227 Top ~F 4

C2228 Top ~E 5

C2230 Top ~E 5

C2231 Top ~F 2

C2232 Top ~F 4

C2233 Top ~C 3

6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 10U M 6V3 0805 10U 6V3 0805C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

Chipcap 5% NP0 27p 50V 0402C

C2234 Top ~D 4

C2235 Top ~C 3

C2237 Top ~E 4

C2240 Top ~J 5

C2241 Top ~D 4

C2242 Top ~F 5

C2243 Top ~F 6

C2244 Top ~J 5

C2300 Top ~I 3

Chipcap 5% NP0 27p 50V 0402C

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

Chipcap 5% NP0 12p 50V 0402C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

CHIPCAP X5R 22U M

C2301 Top ~I 3

Page 2–14 Company Confidential Issue 1

6V3 0805 22u 6V3 0805C

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

CHIPCAP X5R 22U M

C2302 Top ~H 3

C2303 Top ~H 5

C2304 Top ~H 3

C2306 Top ~I 4

C2307 Top ~I 4

C2309 Top ~I 2

6V3 0805 22u 6V3 0805C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 22U M 6V3 0805 22u 6V3 0805C

C2312 Top ~I 5

C2313 Top ~I 5

C2314 Top ~I 2

C2315 Top ~G 2

C2316 Top ~H 3

C2318 Top ~H 1

C2700 BTM ~K 7

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 4U7 K 25V 0805 4u7 25V 0805C

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

Chipcap 5% NP0 27p 50V 0402C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

CHIPCAP X5R 100N M 16V

C2800 Top ~E 5

Issue 1 Company Confidential Page 2–15

0402 100n 16V 0402C

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

CHIPCAP X5R 100N M 16V

C2801 Top ~D 8

C2802 Top ~C 6

C2803 Top ~E 5

C2804 Top ~C 5

0402 100n 16V 0402C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

C2805 Top ~F 7

C2806 Top ~D 8

C2807 Top ~D 8

C2808 Top ~E 8

C2809 Top ~D 5

C2810 Top ~F 7

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

CHIPCAP X5R 100N M 16V

C2811 Top ~E 8

Page 2–16 Company Confidential Issue 1

0402 100n 16V 0402C

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

CHIPCAP X5R 100N M 16V

C2812 Top ~E 5

C2813 Top ~D 5

C2814 Top ~C 6

C3000 BTM ~D 6

0402 100n 16V 0402C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

C3001 BTM ~D 7

C3002 BTM ~B 6

C3003 BTM ~B 7

C3004 Top ~B 3

C3005 Top ~C 5

C3006 Top ~D 4

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

Chipcap X7R 10%

C3007 Top ~C 3

Issue 1 Company Confidential Page 2–17

16V 0402 10n 16V 0402C

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

CHIPCAP X5R 100N M 16V

C3008 Top ~D 4

C4200 Top ~G 4

C4201 Top ~G 5

C4202 Top ~G 4

C4400 Top ~B 21

0402 100n 16V 0402C

CHIPCAP X5R 22U M 6V3 0805 22u 6V3 0805C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

C4401 Top ~C 21

C4402 Top ~B 19

C4403 BTM ~J 11

C4800 Top ~I 6

C4801 Top ~G 5

C4802 Top ~H 5

C4803 Top ~F 6

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

Chipcap 5% NP0 27p 50V 0402C

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

CHIPCAP X5R 100N M 16V

C4804 Top ~I 7

Page 2–18 Company Confidential Issue 1

0402 100n 16V 0402C

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

CHIPCAP X5R 100N M 16V

C4805 Top ~G 8

C4806 Top ~F 8

C4807 Top ~H 5

C4808 Top ~H 5

0402 100n 16V 0402C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

C4809 Top ~G 8

C4810 Top ~I 7

C4811 Top ~F 6

C4812 Top ~G 5

C4813 Top ~F 6

C4814 Top ~H 8

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

Chipcap 5% NP0 22p 50V 0402C

CHIPCAP X5R 100N M 16V

C5000 Top ~K 5

C5001 Top ~H 5

Issue 1 Company Confidential Page 2–19

0402 100n 16V 0402C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

CHIPCAP X5R 100N M 16V

C5002 Top ~J 8

C5003 Top ~I 6

C5004 Top ~I 5

C5005 Top ~I 5

0402 100n 16V 0402C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

C5006 Top ~J 5

C5200 BTM ~C 8

C6031 BTM ~B 4

C6033 BTM ~D 3

C6035 BTM ~D 4

C6036 BTM ~C 3

C6042 BTM ~C 3

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

Chipcap X7R 10%

C6043 BTM ~B 3

C6044 BTM ~C 5

C6045 BTM ~D 4

Page 2–20 Company Confidential Issue 1

16V 0402 10n 16V 0402C

Chipcap 5% NP0 18p 50V 0402C

Chipcap 5% NP0 15p 50V 0402C

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

CHIPCAP NP0 1P2 B

C6046 BTM ~C 4

C6047 BTM ~B 3

C7501 BTM ~G 14

C7503 BTM ~G 13

C7504 BTM ~G 13

C7505 BTM ~G 12

50V 0402 1p2 50V 0402C

CHIPCAP X5R 2U2 K 6V3 0603 2u2 6V3 0603C

Chipcap 5% NP0 18p 50V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

CHIPCAP X5R 100N M 16V 0402 100n 16V 0402C

C7507 BTM ~F 13

C7508 BTM ~F 13

C7509 BTM ~F 13

C7512 BTM ~D 19

C7513 BTM ~F 12

C7514 BTM ~D 19

C7515 BTM ~G 11

C7516 BTM ~E 11

Chipcap 5% NP0 18p 50V 0402C

Chipcap +-0.25pF NP0 2p7 50V 0402C

Chipcap X7R 10% 25V 0402 4n7 25V 0402C

Chipcap +-0.25pF NP0 2p7 50V 0402C

Chipcap 5% NP0 10p 50V 0402C

CHIPCAP NP0 180P J 25V 0402 180p 25V 0402C

CHIPCAP X5R 100N M 16V

C7518 BTM ~G 14

Issue 1 Company Confidential Page 2–21

0402 100n 16V 0402C

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

Chipcap

C7520 BTM ~G 14

C7522 BTM ~E 12

C7523 BTM ~D 18

C7524 BTM ~E 11

C7525 BTM ~D 18

C7527 BTM ~F 13

5% NP0 18p 50V 0402C

CHIPCAP NP0 180P J 25V 0402 180p 25V 0402C

Chipcap +-0.25pF NP0 5p6 50V 0402C

CHIPCAP NP0 2N7 G 50V 0603 2n7 50V 0603C

Chipcap +-0.25pF NP0 5p6 50V 0402C

Chipcap 5% NP0 100p 50V 0402C

C7528 BTM ~F 13

C7529 BTM ~G 12

C7530 BTM ~G 12

C7531 BTM ~F 13

C7532 BTM ~G 12

C7533 BTM ~G 11

C7534 BTM ~G 13

C7535 BTM ~F 12

Chipcap 5% NP0 22p 50V 0402C

Chipcap 5% NP0 100p 50V 0402C

Chipcap X7R 10% 16V 0402 8n2 16V 0402C

Chipcap 5% NP0 22p 50V 0402C

Chipcap X7R 10% 16V 0402 8n2 16V 0402C

Chipcap X7R 10% 16V 0402 10n 16V 0402C

Chipcap X7R 10% 16V 0402 8n2 16V 0402C

Chipcap 5% NP0 100p 50V 0402C

Chipcap X7R 10%

C7536 BTM ~G 13

C7541 BTM ~G 11

Page 2–22 Company Confidential Issue 1

16V 0402 8n2 16V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

CHIPCAP X5R 1U K

C7543 BTM ~G 11

C7545 BTM ~B 17

C7547 BTM ~G 10

C7548 BTM ~G 10

C7549 BTM ~F 11

C7550 BTM ~G 9

6V3 0603 1u0 6.3V 0603C

Chipcap +-0.25pF NP0 4p7 50V 0402C

Chipcap +-0.25pF NP0 1p8 50V 0402C

CHIPCAP X5R 1U K 6V3 0603 1u0 6.3V 0603C

Chipcap 5% NP0 100p 50V 0402C

Chipcap +-0.25pF NP0 2p7 50V 0402C

C7552 BTM ~G 9

C7553 BTM ~G 9

C7554 BTM ~J 13

C7555 BTM ~J 13

C7556 BTM ~D 17

C7558 BTM ~F 10

C7559 BTM ~B 18

Chipcap +-0.25pF NP0 2p7 50V 0402C

Chipcap X7R 10% 16V 0402 8n2 16V 0402C

Chipcap +-0.25pF NP0 4p7 50V 0402C

CHIPCAP NP0 0P5 C 50V 0402 0p5 50V 0402C

Chipcap 5% NP0 10p 50V 0402C

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

Chipcap +-0.25pF NP0 1p0 50V 0402C

Chipcap X7R 10%

C7560 BTM ~G 9

C7561 BTM ~D 17

Issue 1 Company Confidential Page 2–23

25V 0402 4n7 25V 0402C

Chipcap +-0.25pF NP0 4p7 50V 0402C

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

Chipcap +-0.25pF

C7563 BTM ~D 17

C7564 BTM ~C 18

C7567 BTM ~F 10

C7568 BTM ~G 9

C7569 BTM ~D 18

C7570 BTM ~F 9

NP0 4p7 50V 0402C

Chipcap X7R 10% 50V 0402 1n0 50V 0402C

Chipcap 5% NP0 15p 50V 0402C

Chipcap 5% NP0 150p 50V 0402C

CHIPCAP X5R 4U7 K 6V3 0603 4u7 6.3V 0603C

Chipcap 5% NP0 18p 50V 0402C

C7571 BTM ~J 12

C7573 BTM ~G 9

C7575 BTM ~F 10

C7577 BTM ~F 10

C7581 BTM ~D 19

C7582 BTM ~G 9

C7584 BTM ~D 19

C7593 BTM ~D 17

CHIPCAP NP0 330P J 50V 0402 330p 50V 0402C

CHIPCAP NP0 2N2 G 16V 0603 2n2 16V 0603C

Chipcap 5% NP0 15p 50V 0402C

Chipcap +-0.25pF NP0 5p6 50V 0402C

Chipcap 5% NP0 100p 50V 0402C

Chipcap +-0.25pF NP0 5p6 50V 0402C

CHIPCAP X5R 4U7 K 6V3 0603 4u7 6.3V 0603C

Chipcap +-0.25pF

C7596 BTM ~F 14

C7597 BTM ~D 15

Page 2–24 Company Confidential Issue 1

NP0 2p7 50V 0402C

CHIPTCAP 100U M 14V 6X3.2X2 100u_14V 14V

TANT_6.3X

3.5_H2.0

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

CHIPCAP NP0 0P5 C

C7598 BTM ~G 11

C7599 BTM ~D 16

D2800 Top ~D 7

50V 0402 0p5 50V 0402C

Chipcap 5% NP0 10p 50V 0402C

RAP3G V2.11 UMC8D F761800B C27 BGA289 ~ ~ uBGA_289

D3000 BTM ~C 7

D3001 Top ~B 4

D4800 Top ~G 6

D5000 Top ~J 6

F2000 BTM ~J 3

FLASH 4MX16 1.8/

1.8V FBGA44 4Mx16 ~

SDRAM 4MX16

1.8V/1.8V WBGA60 PBFREE 4Mx16 ~

HELEN3 PS1.1E F761991A C027 UBGA289 ~ ~ uBGA_289

COMBO 256M DDR + 256M NAND FBGA121 PBFREE

SM FUSE F

2.0A 32V 2A ~

256M_DDR / 256M_NAN D ~

PBFREEBG A40_64MB _54MHZ_M AX

SDRAM_11 0MHZ_64M BIT_BGA60 _PBFREE_M AX

FBGA121_ H1.1

0603_FUSE _AVX2MAT S

CELL CAPACITOR

0.01MAH

G2200 Top ~B 3

G7500 BTM ~F 11

G7501 BTM ~G 12

Issue 1 Company Confidential Page 2–25

3V3 3V3 ~

VCO 32963980MHZ FOUR 2.7V 20MA

VCTCXO

38.4MHZ

2.5V 38.4MHz ~

32963980MHz ~

BATTER_RB 414H

VCO_FDK_I T_4

NKG3176B _H1.0

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

VCO 32963980MHZ

G7502 BTM ~I 13

L1473 BTM ~I 9

L1474 Top ~J 3

L1479 BTM ~K 12

L1480 BTM ~J 12

FOUR 2.7V 20MA

CHOKE

3.3UH 1.3A

3.7X3.5X1. 2MM 3u3H ~

FERR.BEAD 0R03 42R/ 100MHZ 3A 0805

CHIP COIL 27N J Q27/ 800M 0402 27nH ~ 0402L

32963980MHz ~

42R/ 100MHz ~

VCO_FDK_I T_4

CHOKE_VLF 4012AT

0805_BLM 21

L2000 BTM ~J 3

L2001 Top ~F 2

L2002 BTM ~D 2

L2003 BTM ~D 2

L2100 Top ~G 20

FERR.BEAD 220R/ 100M 2A 0R05 0603

CHIP BEAD ARRAY 2X1000R 0405

220R/ 100MHz ~ 0603_BLM

2x1000R/ 100MHz ~

0405_2_M ATSU

FERR.BEAD 220R/ 100M 2A

L2101 Top ~F 2

Page 2–26 Company Confidential Issue 1

0R05 0603

220R/ 100MHz ~ 0603_BLM

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

CHIP COIL 56N J Q38/

L2102 BTM ~E 19

L2103 BTM ~F 19

L2104 Top ~F 2

L2105 Top ~F 2

250MHZ 0603 56nH ~

CHIP COIL 56N J Q38/ 250MHZ 0603 56nH ~

FERR.BEAD 220R/ 100M 2A 0R05 0603

FERRITE BEAD 220R 0R45 0.3A 0402

220R/ 100MHz ~ 0603_BLM

220R/ 100MHz ~ 0402L_XL

COIL_0603 CS

L2106 Top ~F 2

L2202 Top ~D 5

L2203 Top ~E 5

L2204 Top ~E 5

L2205 Top ~F 3

FERRITE BEAD 220R 0R45 0.3A 0402

FERR.BEAD 220R/ 100M 2A 0R05 0603

FERRITE BEAD 0.6R 600R/ 100MHZ 0402

FERR.BEAD 220R/ 100M 2A 0R05 0603

220R/ 100MHz ~ 0402L_XL

220R/ 100MHz ~ 0603_BLM

600R/ 100MHz ~

220R/ 100MHz ~ 0603_BLM

FERRITE_0 402

FERRITE BEAD 0.6R 600R/ 100MHZ

L2206 Top ~E 5

Issue 1 Company Confidential Page 2–27

0402

600R/ 100MHz ~

FERRITE_0 402

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

FERR.BEAD 220R/

L2301 Top ~I 3

L2302 Top ~H 3

L2304 Top ~H 2

L4200 Top ~G 3

L4201 Top ~G 5

100M 2A 0R05 0603

CHOKE 10U

0.8A 0R24 4X4X1.8 10uH ~

CHOKE 22U M 1R4

0.33A

3.3X3.3X1. 5 22uH ~

CHOKE 10U

0.8A 0R24 4X4X1.8 10uH ~

FERR.BEAD 220R/ 100M 2A 0R05 0603

220R/ 100MHz ~ 0603_BLM

CHOKE_SER 400

CHOKE_984 FB

CHOKE_SER 400

220R/ 100MHz ~ 0603_BLM

L4400 Top ~C 21

L4401 Top ~D 21

L5200 BTM ~C 9

L6031 BTM ~C 4

L6032 BTM ~C 4

FERRITE BEAD 0.6R 600R/ 100MHZ 0402

CHIP COIL 3N3 +-0N3 Q28/800M 0402 3n3H ~ 0402L

600R/ 100MHz ~

FERRITE_0 402

CHIP COIL 100N J Q16/300M

L7502 BTM ~G 9

Page 2–28 Company Confidential Issue 1

0402 100nH ~ 0402L

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

FERRITE BEAD 0.6R 600R/

L7503 BTM ~G 11

L7504 BTM ~D 19

L7505 BTM ~D 19

L7506 BTM ~D 18

L7516 BTM ~D 16

100MHZ 0402

CHIP COIL 27N J Q27/ 800M 0402 27nH ~ 0402L

CHIP COIL 12N J Q31/ 800M 0402 12nH ~ 0402L

FERRITE BEAD 0.6R 600R/ 100MHZ 0402

600R/ 100MHz ~

FERRITE_0 402

L7517 BTM ~G 10

N1470 BTM ~C 8

N1471 BTM ~I 11

N2200 Top ~E 3

N2300 Top ~H 4

CHIP COIL 1N5 +-0N3 Q33/800M 0402 1n5H ~ 0402L

REG LP3990YD X-1.5V LLP6 ~ 1.5V LLP6

STEP-UP DC/DC CONV SON30248 ~ ~

RETU 3.02 L TSA1GJWE TFBGA108 ~ ~ TFBGA_108

TAHVO V4.1 TFBGA84 6X6 ~ ~

SON3024_ 8

TFBGA_84_

6.15X6.15

WHITE LED DRIVER 4LEDS 500MW 8BUMP

N2301 Top ~G 2

Issue 1 Company Confidential Page 2–29

USMD8 ~ ~

USMD8_1.6 9X1.69

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

DC_DC CONV

N4200 Top ~G 4

N6030 BTM ~C 3

N6031 BTM ~B 3

N7500 BTM ~F 13

LM2708H-

1.40V/

1.09V ~ ~

BC3-ROM WITH BC2 MOULD MATERIAL ~ ~

VREG 2.85/ 150MA LP3987-

2.85 USMD5 ~ 2.85V

RF ASIC HINKU310 A TFBGA84 ~ ~

USMD_10_

2.458X1.8 99

TFBGA84_ H1.0

USMD5_1.4 68X1.036

TFBGA_84_

6.15X6.15

N7501 BTM ~G 10

N7502 BTM ~C 17

R1470 Top ~F 8

R1471 Top ~F 8

R1472 Top ~H 8

R1473 Top ~H 8

R1474 Top ~F 7

R1487 BTM ~I 10

RF ASIC VINKU314 A TFBGA64 ~ ~

PW AMP RF9292E9. 2 QUADBAN D ~ ~

Resistor 5% 63mW 100R ~ 0402R

Resistor 5% 63mW 3k3 ~ 0402R

Resistor 5% 63mW 33R ~ 0402R

CHIPRES 0W06 6R8 J 0402 6R8 ~ 0402R

TFBGA64_ H1.2

RITSA_PA_ REL3

Resistor

R1489 BTM ~H 11

R2000 BTM ~E 3

Page 2–30 Company Confidential Issue 1

5% 63mW 3k3 ~ 0402R

Resistor 5% 63mW 220R ~ 0402R

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

ASIP MIC W/ESD RES

R2001 Top ~E 2

R2002 Top ~E 2

R2003 Top ~E 1

R2004 Top ~D 2

R2005 Top ~D 2

R2006 BTM ~C 2

+CAP+ZDI BGA11 ~ ~

Resistor 5% 63mW 10R ~ 0402R

ASIP 4XESD **PBFREE** BGA5 ~ ~ uBGA5

uBGA11_2. 15X1.65

R2007 BTM ~F 2

R2009 BTM ~F 3

R2010 Top ~H 4

R2011 BTM ~F 3

R2070 BTM ~G 2

R2071 Top ~B 3

R2072 BTM ~G 2

ASIP SILIC USB OTG / ESD BGA11 ~ ~

Resistor 5% 63mW 100R ~ 0402R

Resistor 5% 63mW 220k ~ 0402R

Resistor 5% 63mW 120k ~ 0402R

CHIP VARISTOR VWM14V VC50V 0402 14V/50V ~ 0402_VAR

NTC RES 47K J B=4050 +-3% 0402 47k ~

Resistor 5% 63mW 100R ~ 0402R

uBGA11_1. 6X2.1

0402_NTH 5

ASIP SINGLE ENDED MICROPHO NE INTERF

R2100 Top ~E 2

R2101 Top ~E 2

Issue 1 Company Confidential Page 2–31

BGA8 ~ ~

Resistor 5% 63mW 220R ~ 0402R

FLIP_CHIP_ 8_1.7X1.7

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

CHIP VARISTOR VWM14V VC50V

R2104 Top ~F 19

R2105 Top ~G 19

R2106 BTM ~E 19

R2107 BTM ~E 19

0402 14V/50V ~ 0402_VAR

CHIP VARISTOR VWM14V VC50V 0402 14V/50V ~ 0402_VAR

R2200 Top ~D 2

R2201 Top ~D 4

R2205 Top ~D 4

R2301 Top ~G 2

R2302 Top ~G 2

R2303 Top ~G 2

R2304 Top ~G 1

R2305 Top ~H 5

R2700 Top ~J 4

Resistor 5% 63mW 100k ~ 0402R

Resistor 5% 63mW 120k ~ 0402R

CHIPRES 0W06 2M2 J 0402 2M2 ~ 0402R

Resistor 5% 63mW 4k7 ~ 0402R

Resistor 5% 63mW 10k ~ 0402R

Resistor 5% 63mW 1k0 ~ 0402R

Resistor 5% 63mW 39R ~ 0402R

Resistor 5% 63mW 33R ~ 0402R

ASIP SIM INTERFACE **LOW CAP**BGA 8 ~ ~

uBGA8_1.4 7X1.47

Resistor

R3000 BTM ~B 7

Page 2–32 Company Confidential Issue 1

5% 63mW 4k7 ~ 0402R

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

Resistor

R4400 Top ~D 2

R4401 Top ~D 3

R4402 Top ~D 2

R4403 Top ~J 21

R4404 BTM ~J 17

R4405 BTM ~J 17

5% 63mW 470k ~ 0402R

Resistor 5% 63mW 100k ~ 0402R

Resistor 5% 63mW 470k ~ 0402R

NTC RES 47K J B=4050 +-3% 0402 47k ~

CHIP VARISTOR VWM14V VC50V 0402 14V/50V ~ 0402_VAR

0402_NTH 5

R4406 BTM ~B 17

R4408 BTM ~K 11

R4409 BTM ~K 11

R4410 BTM ~K 11

R4800 Top ~I 7

R4809 Top ~F 5

R4810 Top ~H 8

CHIP VARISTOR VWM14V VC50V 0402 14V/50V ~ 0402_VAR

Resistor 5% 63mW 10k ~ 0402R

Resistor 5% 63mW 1k0 ~ 0402R

CHIP VARISTOR VWM14V VC50V 0402 14V/50V ~ 0402_VAR

Resistor 5% 63mW 10R ~ 0402R

Resistor 5% 63mW 1k0 ~ 0402R

Resistor 5% 63mW 15R ~ 0402R

Resistor

R5100 BTM ~E 8

Issue 1 Company Confidential Page 2–33

5% 63mW 10k ~ 0402R

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

ASIP EMIF04MMC02F2*

R5200 BTM ~B 8

R5204 BTM ~C 15

R6030 BTM ~D 4

R6034 BTM ~B 3

R7501 BTM ~E 11

*PBFREE** ~ ~

CHIP VARISTOR VWM14V VC50V 0402 14V/50V ~ 0402_VAR

Resistor 5% 63mW 10k ~ 0402R

CHIPRES 0W06 2R2 J 0402 2R2 ~ 0402R

Resistor 5% 63mW 3k9 ~ 0402R

uBGA11_1. 62X2.12

R7503 BTM ~F 9

R7504 BTM ~G 13

R7505 BTM ~E 12

R7506 BTM ~D 18

R7509 BTM ~G 11

R7512 BTM ~D 16

R7514 BTM ~F 11

R7516 BTM ~C 18

Resistor 5% 63mW 4k7 ~ 0402R

CHIPRES 0W06 10K F 0402 10k ~ 0402R

Chipres 0W06 6k8 F 0402 6k8 ~ 0402R

Resistor 5% 63mW 33R ~ 0402R

Resistor 5% 63mW 22k ~ 0402R

RES NETWORK 0W04 2DB ATT 0404

Resistor 5% 63mW 12k ~ 0402R

Resistor 5% 63mW 1k0 ~ 0402R

436R/ 11R6/ 436R ~

0404_RAC1 0

Resistor

R7518 BTM ~B 17

R7519 BTM ~G 10

Page 2–34 Company Confidential Issue 1

5% 63mW 470k ~ 0402R

Resistor 5% 63mW 1k0 ~ 0402R

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

CHIPRES 0W06 10K

R7521 BTM ~F 10

R7523 BTM ~G 9

R7528 BTM ~G 10

R7534 BTM ~B 18

S4400 BTM ~K 18

F 0402 10k ~ 0402R

CHIPRES 0W06 9K1 F 100PPM 0402 9k1 ~ 0402R

Resistor 5% 63mW 470k ~ 0402R

SM TACT SW TRAV

0.2

4.1X3.55X

1.75 ~ ~

SWITCH_SK RE_II

S4401 BTM ~A 18

S5200 BTM ~B 15

S5202 BTM ~K 11

T7501 BTM ~F 12

T7502 BTM ~C 16

SM TACT SW TRAV

0.2

4.1X3.55X

1.75 ~ ~

SM SW DETECTOR SPST-NO 5V 1MA ~ ~

SWITCH PB LIGHT TOUCH EVPAA002 C ~ ~

TRANSF BALUN 3800 +-550MHZ 0805 ~ ~

TRANSF BALUN 1800 +-100mhz 2x1.25 ~ ~

SWITCH_SK RE_II

SWITCH_SP VN220100

SWITCH_EV Q058Z400 7

TRANS_LD B15

TRANSF BALUN 3800 +-550MHZ

T7503 BTM ~H 13

Issue 1 Company Confidential Page 2–35

0805 ~ ~

TRANS_LD B15

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

DIX2 FAST 1PS89SS05

V1470 Top ~J 4

V1471 BTM ~I 11

V1472 BTM ~I 10

V2000 BTM ~J 3

80V CC SC89 ~ ~

SCH DI PMEG3002 30V 500MA SOD882 ~ ~

MOSFET N 20V 350MA SOT416 ~ ~

TVS DI 1PMT16AT 3 16V 175W PWRMITE ~ ~ CASE_457

SS_MINI_3_ H0.8

DIODE_PME G3002

SC_75A_H0 .95

V2300 Top ~H 5

V4400 Top ~J 21

X1470 BTM ~F 16

X2001 BTM ~E 1

X2060 Top ~K 14

TR DTC143ZE N RBE4K7/ 47K 0A1 SC75 ~ ~ EM3

DI PHOTO PT202MR0 MP 620NM

1.25X2 ~ ~

CAMERA MOD.SOCKE T 2X7POL SPR P1.4 ~ ~

SM SYSTEM CONNECTO R 14POL ~ ~

MODULE ID COMPONEN T

2.8X1.8X0. 3 ~ ~

PT202MR0 MP

SOCKET_D MD10413

SYSCON_M Q202_NK_ 14R3

TRACEABIL ITY_PAD

SM LYNX BATT.CON N 3POL 12V

X2070 BTM ~H 3

X2700 BTM ~H 6

Page 2–36 Company Confidential Issue 1

2A H7 ~ ~

SM SIM CONN 2X3POL P2.54 15V

0.5A ~ ~

LYNX_BATT _CONN

SIM_READE R_M_C707_ 10M006_5 32_2

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Item Side Grid reference Description and Value Type

SM CONN

X4400 Top ~B 6

X4401 Top ~C 20

X4402 Top ~K 16

X4403 Top ~B 16

16P SPR P1.3 50V PWB/PWB ~ ~

SM CONN 2X12F P0.4 30V 0.3A PCB/PCB ~ ~

GROUNDIN G SPRING DMD12054 RM-1 ~ ~

SMK_4309_ B_B_16P_V 8

JST_R_JAVK _G_1_R3

GND_SPRIN G_DMD120 54

X5200 BTM ~C 12

Z2000 BTM ~F 2

Z2001 BTM ~F 2

Z2003 BTM ~G 2

Z4400 Top ~B 8

CONN SMC RS-MMC 6POL P2.5 ~ ~

FERRITE BEAD 0.6R 600R/ 100MHZ 0402

ASIP 10-CH ESD EMI FILTER BGA25 ~ ~

600R/ 100MHz ~

MOLEX_MM C_P03_3D0 545_001

FERRITE_0 402

uBGA25_2. 69X2.69

ASIP 2-CH MIC EMI/ ESD **PB-

Z4401 Top ~B 7

Z4402 Top ~I 8

Issue 1 Company Confidential Page 2–37

FREE** ~ ~

ASIP 10-CH ESD EMI FILTER BGA25 ~ ~

FC6_1.65X

1.15

uBGA25_2. 69X2.69

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

Item Side Grid reference Description and Value Type

ASIP 10-CH ESD EMI

Z4403 Top ~J 8

Z6030 BTM ~C 5

Z7500 BTM ~D 16

Z7503 BTM ~C 19

FILTER BGA25 ~ ~

LTCC FILT

2441.75 +-41.75MH Z 2.5X2

FERRITE BEAD 0R01 28R/ 100MHZ 0603

ANT.SW +3SAW 880-960/ 17101990MHZ ~ ~

2441.75M Hz ~

28R/ 100MHz ~

uBGA25_2. 69X2.69

EZFVQ42N M61S

FERRITE_FB MJ1608

ANT_SW_M 043B

SAW FILTER

Z7504 BTM ~C 16

897.5 +-17.5MHZ

2.0X1.6 897.5MHz ~

FILTER_SA W_2.1X1.7 _H0.8

Variant parts for RM-58

Item EU description US description

Z7503 ANT.SW+3SAW 880-960/1710-

1990MHZ

Z7504 SAW FILTER 897.5+-17.5MHZ

2.0X1.6

I042 Antenna GSM900/1800/1900 Antenna GSM850/1800/1900

RF SWITCH MODULE ESHS-L080SQVer.1.0

SAW FILTER 836.5+-12.5MHZ/

2.0X1.6

Page 2–38 Company Confidential Issue 1

RM-57/58 Parts Lists and Component Layouts Nokia Customer Care

Component layouts

Component layout - bottom (1LF_09a)

Component layout - top (1LF_09a)

Issue 1 Company Confidential Page 2–39

RM-57/58

Nokia Customer Care Parts Lists and Component Layouts

(This page left intentionally blank.)

Page 2–40 Company Confidential Issue 1

Nokia Customer Care

3 — Service Software

Instructions

Issue 1 Company Confidential Page 3–1

RM-57/58

Nokia Customer Care Service Software Instructions

(This page left intentionally blank.)

Page 3–2 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

Table of Contents

Phoenix installation steps in brief.............................................................................................................................................3–5

Installing Phoenix...........................................................................................................................................................................3–6

Updating Phoenix installation....................................................................................................................................................3–8

Uninstalling Phoenix......................................................................................................................................................................3–9

Repairing Phoenix installation.................................................................................................................................................3–10

Phoenix service software data package overview.............................................................................................................3–11

Installing Phoenix data package.............................................................................................................................................3–11

Uninstalling Phoenix data package........................................................................................................................................3–15

Configuring users in Phoenix....................................................................................................................................................3–16

Managing connections in Phoenix..........................................................................................................................................3–16

Installing flash support files for FPS-8 and FPS-10.............................................................................................................3–19

Updating FPS-8 and FPS-10 flash prommer software.......................................................................................................3–22

Activating FPS-8.............................................................................................................................................................................3–23

Deactivating FPS-8........................................................................................................................................................................3–24

List of Figures

Figure 2 Dongle not found...........................................................................................................................................................3–6

Figure 3 Disclaimer text................................................................................................................................................................3–7

Figure 4 InstallShield Wizard Complete...................................................................................................................................3–8

Figure 5 Installation interrupted................................................................................................................................................3–9

Figure 6 Remove program............................................................................................................................................................3–9

Figure 7 Finish uninstallation...................................................................................................................................................3–10

Figure 8 Repair program............................................................................................................................................................3–11

Figure 9 Continue data package installation.......................................................................................................................3–12

Figure 10 Data package setup information..........................................................................................................................3–13

Figure 11 Data package destination folder..........................................................................................................................3–13

Figure 12 Start copying files......................................................................................................................................................3–14

Figure 13 Finish data package installation..........................................................................................................................3–14

Figure 14 Uninstalling Phoenix data package.....................................................................................................................3–15

Figure 15 Finishing data package uninstallation...............................................................................................................3–15

Figure 16 Login..............................................................................................................................................................................3–16

Figure 17 Login, user configured.............................................................................................................................................3–16

Figure 18 Select mode: Manual................................................................................................................................................3–17

Figure 19 Connections list..........................................................................................................................................................3–18

Figure 20 Connection information..........................................................................................................................................3–18

Figure 21 Scan product...............................................................................................................................................................3–19

Figure 22 Product support module information................................................................................................................3–19

Figure 23 Flash update welcome dialog...............................................................................................................................3–20

Figure 24 Flash installation interrupted................................................................................................................................3–20

Figure 25 Flash destination folder..........................................................................................................................................3–21

Figure 26 Finish flash update....................................................................................................................................................3–21

Figure 27 Choosing Prommer maintenance........................................................................................................................3–22

Figure 28 Prommer SW update finished...............................................................................................................................3–22

Figure 29 Prommer maintenance window..........................................................................................................................3–23

Figure 30 Flash directory window...........................................................................................................................................3–23

Figure 31 Prommer maintenance...........................................................................................................................................3–24

Figure 32 Box activation.............................................................................................................................................................3–24

Figure 33 Deactivation warning..............................................................................................................................................3–25

Issue 1 Company Confidential Page 3–3

RM-57/58

Nokia Customer Care Service Software Instructions

(This page left intentionally blank.)

Page 3–4 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

Phoenix installation steps in brief

Phoenix is the service software for reprogramming, testing and tuning the phone. Recommended PC HW requirements:

• Computer Processor: Pentium 700 MHz or higher

• RAM 256 MB

• Disk space 100-200 MB Supported operating systems:

• Windows 2000 Service Pack 3 or higher

• Windows XP Service Pack 1 or higher To install Phoenix, you need to:

• Connect a DK2 Dongle

• Install the Phoenix Service SW

• Install the Data Package for Phoenix

• Configure users

• Manage connection settings (depends on the tools you are using) If you use FPS-8:

• Update FPS-8 SW

• Activate FPS-8 If you use FPS-10:

• Update FPS-10 SW

Note: There is no need to activate FPS-10.

• Activate SX-4 Smart Card if you need tuning and testing functions in service software

Note: When FPS-10 is used only for product SW updates, SX-4 Smart card is not needed.

Phoenix is now ready to be used with FPS-8 or FPS-10 flash prommers and other tools as well. The Phoenix Service Software installation contains:

• Service software support for all phone models included in the package

• Flash update package files for programming devices

• All needed drivers for:

• DK2 dongle

• DKU-2 USB cable

Note: Separate installation packages for flash update files and drivers are also available, but it is not

necessary to use them unless updates appear between Phoenix Service SW releases. If separate update packages are used, they should be used after Phoenix and data packages have been installed.

The phone model specific data package includes all changing product specific data:

• Product software Binary files

• Files for type label printing

• Validation file for the Faultlog repair data reporting system

• All product specific configuration files for Phoenix software components

Note: Phoenix Service SW and phone data packages should only be used as complete installation

packages. Uninstallation should be made from the Windows Control Panel.

Issue 1 Company Confidential Page 3–5

RM-57/58

Nokia Customer Care Service Software Instructions

Installing Phoenix

Before you begin

• Check that a dongle is attached to the parallel port of your computer.

• Download the installation package (for example, phoenix_service_sw_2004_39_x_xx.exe) to your computer (in C:\TEMP, for instance).

• Close all other programs.

• Depending on the operating system, administrator rights may be required to be able to install Phoenix .

• If uninstalling or rebooting is needed at any point, you will be prompted by the InstallShield program.

Context

At some point during the installation procedure you may get the following message:

Figure 2 Dongle not found

One possible reason may be a defective or too old PKD-1 dongle (five digit serial number dongle when used with FPS-8/FPS-10 prommers).

Check the COM/parallel ports used first! After correcting the problem Installation can be restarted. For more detailed information, please refer to Phoenix Help files. Each feature in Phoenix has its own Help

function, which can be activated while running the program. Press the F1 key or the feature’s Help button to activate a Help file.

Steps

1. To start installation, run the application file (for example,phoenix_service_sw_2004_39_x_xx.exe).

2. In the Welcome dialogue, click Next.

Page 3–6 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

3. Read the disclaimer text carefully and click Yes.

Figure 3 Disclaimer text

4. Choose destination folder. The default folder C:\ProgramFiles\Nokia\Phoenix is recommended.

5. To continue, click Next. You may choose another location by selecting Browse (not recommended).

6. Wait for the components to be copied. The progress of the setup is shown in the Setup Status window.

7. Wait for the drivers to be installed and updated. The process may take several minutes to complete. If the operating system does not require rebooting, the PC components are registered right away. If the operating system used requires restarting your computer, the Install Shield Wizard will tell you about

it. Select Yes... to reboot the PC immediately and No.. to reboot the PC manually afterwards. After the reboot, components are registered and Phoenix is ready for use.

Note: Phoenix does not work, if components have not been registered.

Issue 1 Company Confidential Page 3–7

RM-57/58

Nokia Customer Care Service Software Instructions

8. To end installation, click Finish .

Figure 4 InstallShield Wizard Complete

Phoenix is now ready for use.

Next action

After the installation, Phoenix service software can be used after:

• installing phone model specific data package for Phoenix

• configuring users and connections FPS-8* and FPS-10 flash prommers can be used after updating their Flash Update Package files.

Updating Phoenix installation

If you already have the Phoenix service software installed on your computer, you need to update the software when new versions are released.

When you update Phoenix (for example, a14_2004_16_4_47 to a15_2004_24_7_55), the update will take place automatically without uninstallation.

Always use the latest available versions of both Phoenix and the phone-specific data package. Instructions can be found in the phone model specific Technical Bulletins and phone data package readme.txt files (shown during installation).

To update Phoenix, you need to follow the same steps as when installing it for the first time:

• Download the installation package to your computer hard disk.

• Close all other programs.

• Run the application file (for example, phoenix_service_sw_2004_39_x_xx.exe). A new Phoenix version will be installed and driver versions will be checked and updated. If you try to update the Phoenix with the same version you already have (for example, a15_2004_24_7_55

to a15_2004_24_7_55) you are asked if you want to uninstall the existing version of Phoenix. In this case you can choose between a total uninstallation and repair just like when you choose to uninstall Phoenix service software from the Windows Control panel.

Page 3–8 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

If you try to install an older version (for example, downgrade from a15_2004_24_7_55 to a14_2004_16_4_47), installation will be interrupted.

Figure 5 Installation interrupted

Always follow the instructions on the screen.

Uninstalling Phoenix

Context

You can uninstall Phoenix service software manually from the Windows Control Panel.

Steps

1. Open the Windows Control Panel and choose Add/Remove Programs.

2.

To uninstall Phoenix, choose Phoenix Service Software → Change/Remove → Remove .

Figure 6 Remove program

The progress of the uninstallation is shown.

Issue 1 Company Confidential Page 3–9

RM-57/58

Nokia Customer Care Service Software Instructions

3. If the operating system does not require rebooting, click Finish to complete.

Figure 7 Finish uninstallation

If the operating system requires rebooting, InstallShield Wizard will notify you. Select Yes... to reboot the PC immediately and No... to reboot the PC manually afterwards.

Repairing Phoenix installation

Context

If you experience any problems with the service software or suspect that files have been lost, you can use the repair function before completely reinstalling Phoenix.

Note: The original installation package (for example, phoenix_service_sw_a15_2004_24_7_55.exe) must

be found on your PC when you run the repair setup.

Steps

1.

Open Windows Control Panel → Add/Remove Programs .

2.

Select Phoenix Service Software → Change/Remove .

Page 3–10 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

3. In the following view, select Repair.

Figure 8 Repair program

Phoenix will now reinstall components and register them. The procedure is the same as when updating Phoenix.

4. To complete the repair, click Finish.

Phoenix service software data package overview

Each product has its own data package (DP). The product data package contains all product-specific data files to make the Phoenix service software and tools usable with a certain phone model.

The data package contains the following:

• Product software Binary files

• Files for type label printing

• Validation file for the Faultlog repair data reporting system

• All product-specific configuration files for Phoenix software components

Data files are stored under C:\Program Files\Nokia\Phoenix (default).

Installing Phoenix data package

Before you begin

• A product-specific data package contains all data to make the Phoenix service software and tools usable with

a certain phone model.

• Check that the dongle is attached to the parallel port of your computer.

• Install Phoenix service SW.

•

Download the installation package (for example, XX-XX*_dp_EA_v_1_0.exe) to your computer (for example, in C:\TEMP).

• Close all other programs.

(* = type designator of the product) If you already have Phoenix installed on your computer, you will need to update it when a new version is

released.

Issue 1 Company Confidential Page 3–11

RM-57/58

Nokia Customer Care Service Software Instructions

Note: Very often the Phoenix Service SW and the phone-specific data package for Phoenix come in

pairs, meaning that a certain version of Phoenix can only be used with a certain version of the data package. Always use the latest available versions of both. Instructions can be found in phone model specific Technical Bulletins and readme.txt files of the data packages.

Steps

1. To start installation, run the application file (for example, XX-XX_dp_EA_ v_1_0.exe).

2. Click Next, and wait for the installation files to be extracted.

3. To continue, click Next .

Figure 9 Continue data package installation

In this view you can see the contents of the data package. Read the text carefully. There should be information about the Phoenix version required with this data package.

Page 3–12 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

4. To continue, click Next .

Figure 10 Data package setup information

5. Confirm location and click Next to continue.

Figure 11 Data package destination folder

The install shield checks where the Phoenix application is installed and the directory is shown.

Issue 1 Company Confidential Page 3–13

RM-57/58

Nokia Customer Care Service Software Instructions

6. To start copying the files, click Next.

Figure 12 Start copying files

Phone model specific files are installed. Please wait.

7. To complete the installation, click Finish.

Figure 13 Finish data package installation

You now have all phone model specific files installed in your Phoenix Service SW.

Next action

Phoenix can be used, for example, for flashing phones and printing type labels after:

• Configuring users

• Managing connections

Page 3–14 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

FPS-8* and FPS-10 can be used after updating their Flash Update Package files.

Uninstalling Phoenix data package

Context

If you try to install the same version of the Phoenix data package that you already have, you are asked if you want to uninstall the existing version.

There is no need to uninstall the older version of a data package, unless instructions to do so are given in the readme.txt file of the data package and bulletins related to the release.

Please read all related documents carefully.

Steps

1. To uninstall the data package, click OK Cancel to interrupt the uninstallation.

Figure 14 Uninstalling Phoenix data package

2. Once the previously installed data package is uninstalled, click Finish.

Figure 15 Finishing data package uninstallation

Alternative steps

•

You can also uninstall the data package manually from Windows Control Panel → Add/Remove Programs → xx-xx * Phone Data Package . (*= type designator of the phone)

Next action

Run the installation package again to continue installation from the beginning.

Issue 1 Company Confidential Page 3–15

RM-57/58

Nokia Customer Care Service Software Instructions

Configuring users in Phoenix

Steps

1. Start Phoenix Service SW and log in.

Figure 16 Login

If the user ID is already configured, choose it from the dropdown list and click OK. To add a new user or edit existing ones, click Maintain.

2. To add information for a new user, click New.

3. Type in the name and initials of the user and click OK. A new user is now created.

4. Click OK. You are now able to login with the user name created.

5. Click OK.

Figure 17 Login, user configured

Managing connections in Phoenix

Context

With the Manage Connections feature you can edit and delete existing connections and create new ones.

Steps

1. Start Phoenix Service SW and log in.

2.

Choose File → Manage Connections .

Page 3–16 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

3. To add a new connection, click Add, and select if you want to create it manually or by using the Connection

Wizard.

In the following dialogs you are asked to select settings for the connection. If you use the Wizard, connect the tools and a phone to your PC and the wizard will automatically try to configure the correct connection.

4. Select Manual mode, and click Next to continue.

Figure 18 Select mode: Manual

i For an FPS-10 flash prommer with a USB Connection, choose the following connection settings

• Media: FPS-10 USB

• Device Index: 0

• Serial Num: See Serial No from the label attached to the bottom of your FPS-10

• Active Media: USB

ii For an FPS-10 flash prommer with a LAN connection, choose the following connection settings

• Media: FPS-10 TCP/IP

• Net Serv Name: Select “Scan”. Choose your own FPS-10 device based on the correct MAC address. See Serial No from the label attached to the bottom of your FPS-10.

• Port Num: Use default value, click “Next”.

• Protocol Family: Use default value, click “Next”.

• Socket Type: Use default value, click “Next”.

• TX Buffer Size: Use default value, click “Next”.

• RX Buffer Size: Use default value, click “Next”.

Note: When the phone is connected to a PC for the first time, allow the PC to install the USB device

drivers first. Please note that this may take some time to complete.

Issue 1 Company Confidential Page 3–17

RM-57/58

Nokia Customer Care Service Software Instructions

After the drivers are installed and if there are problems, check that the USB connection is active from the Windows Control Panel or contact the local PC support.

iii For an FPS-8 flash prommer, choose the following connection settings:

• Media: FPS-8

• Port Num: COM Port where FPS-8 is connected

• COMBOX_DEF_MEDIA: FBUS

iv For a plain USB connection choose the following connection settings:

Note: First connect the DKU-2 USB cable between the PC USB port and phone.

• Media: USB

Note: When the phone is connected to a PC for the first time, allow the PC to install the USB device

drivers first. Please note that this may take some time to complete. After the drivers are installed and if there are problems, check that the USB connection is active from

the Windows Control Panel or contact the local PC support.

5. To complete the configuration, click Finish. If you are using the Wizard, connect the tools and a phone to your PC and the wizard will automatically try

to configure the correct connection. Please note that this may take time because Phoenix will go through all connections on the PC.

6. Click the connection you want to activate and use up/down arrows to move it on top of the list, then click Apply.

Figure 19 Connections list

The connection is now selected and can be used after closing the Manage Connections window. The selected connection is shown on the right hand bottom corner of the screen.

Figure 20 Connection information

Page 3–18 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

7. To use the selected connection, connect the phone to Phoenix with correct service tools, make sure that the

phone is switched on and from the File menu, choose Scan Product.

Figure 21 Scan product

Figure 22 Product support module information

Installing flash support files for FPS-8 and FPS-10

Before you begin

• Install Phoenix Service SW.

• Install phone model specific data package for Phoenix.

• If you want to update the flash support files, they are delivered in the same installation package with Phoenix

or newer Phoenix packages beginning from December 2004. In case you want to update the MCU files, install the latest data package (see Technical Bulletins for information on the latest one). However, normally it is enough to install Phoenix and the phone-specific data package because the Phoenix installation always includes the latest flash update package files for FPS-8 and FPS-10.

• A separate installation package for flash support files is available, and the files can be updated according to

this instruction if updates appear between Phoenix/data package releases.

Context

If you are not using a separate installation package, you can skip this section and continue with Updating FPS-

8 and FPS-10 flash prommer software (Page 3–22) after installing a new phone data package.

Issue 1 Company Confidential Page 3–19

RM-57/58

Nokia Customer Care Service Software Instructions

Steps

1. To begin the installation, double-click the flash update file (for example, flash_update_03_183_0014.exe).

Figure 23 Flash update welcome dialog

If the same version of Flash Update package already exists, and you want to reinstall it, the previous package is first uninstalled. Restart installation again after uninstallation.

2. If you try to downgrade the existing version to older ones, the setup will be aborted. If there is a need to downgrade the version, uninstall newer files manually from the Windows Control Panel and then rerun the installation.

Figure 24 Flash installation interrupted

If an older version exists on your PC and it needs to be updated, click Next to continue installation.

Page 3–20 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

3. It is highly recommended to install the files to the default destination folder C:\Program Files\Nokia

\Phoenix. To continue, click Next.

Figure 25 Flash destination folder

When installing the flash update files for the first time, you may choose another location by selecting Browse (not recommended).

4. To complete the installation procedure, click Finish .

Figure 26 Finish flash update

Next action

FPS-8 and FPS-10 flash prommers must be updated using Phoenix!

Issue 1 Company Confidential Page 3–21

RM-57/58

Nokia Customer Care Service Software Instructions

Updating FPS-8 and FPS-10 flash prommer software

Steps

1. Start Phoenix Service Software and log in, manage connection correctly for your flash prommer.

2.

Choose Maintenance → Prommer maintenance .

Figure 27 Choosing Prommer maintenance

3. When the new flash update package is installed to computer, you aree asked to update the files to your prommer. To update the files, click Yes.

4. Wait until you are notified that the update has been successful; the procedure will take a couple of minutes. To close the Prommer Maintenance window, click OK.

Figure 28 Prommer SW update finished

Page 3–22 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

Figure 29 Prommer maintenance window

Alternative steps

• To update the FPS-8 SW, click theUpdate button and select the appropriate fps8upd.ini file in C:\Program

Files\Nokia\Phoenix\Flash.

• To update the FPS-10 SW, click the Update button and select the appropriate fpsxupd.ini file in C:\Program

Files\Nokia\Phoenix\Flash.

Figure 30 Flash directory window

• All files can be loaded separately to the prommer used. To do this, click the right mouse button in the Flash

box files window and select the file type to be loaded. More information can be found in the Phoenix Help.

Activating FPS-8

Context

Before FPS-8 can be successfully used for phone programming, it must first be activated.

Issue 1 Company Confidential Page 3–23

RM-57/58

Nokia Customer Care Service Software Instructions

First fill in the FPS-8 activation request sheet in the FPS-8 sales package and follow the instructions given. When activation file is received (for example, 00000.in), copy it to the C:\ProgramFiles\Nokia\Phoenix

\BoxActivation directory on your computer (this directory is created when Phoenix is installed).

Steps

1. Start Phoenix Service Software.

2.

Choose Maintenance → Prommer Maintenance .

Figure 31 Prommer maintenance

3. In the Prommer Maintenance window, click Activate.

4. To find the activation file if you saved it to some other directory on your PC, click Browse.

5. To activate the prommer, select the activation file and click Open.

Figure 32 Box activation

6. To complete the activation, restart FPS-8.

Deactivating FPS-8

Context

If there is, for example, a need to send the FPS-8 box for repair, it must be deactivated first.

Steps

1. Start Phoenix Service Software.

2.

Choose Maintenance → Prommer Maintenance .

3. In the Prommer Maintenance window, click Deactivate.

Page 3–24 Company Confidential Issue 1

RM-57/58 Service Software Instructions Nokia Customer Care

4. To confirm the deactivation, click Yes.

Figure 33 Deactivation warning

The box is deactivated.

5. To complete the deactivation, restart FPS-8.

Issue 1 Company Confidential Page 3–25

RM-57/58

Nokia Customer Care Service Software Instructions

(This page left intentionally blank.)

Page 3–26 Company Confidential Issue 1

Nokia Customer Care

4 — Service Tools and Service

Concepts

Issue 1 Company Confidential Page 4–1

RM-57/58

Nokia Customer Care Service Tools and Service Concepts

(This page left intentionally blank.)

Page 4–2 Company Confidential Issue 1

RM-57/58 Service Tools and Service Concepts Nokia Customer Care

Table of Contents

Service tools......................................................................................................................................................................................4–5

AC-33.............................................................................................................................................................................................4–5

AD-18FS.........................................................................................................................................................................................4–5

CA-31D...........................................................................................................................................................................................4–5

CA-35S...........................................................................................................................................................................................4–6

CU-4................................................................................................................................................................................................4–6

DKU-2.............................................................................................................................................................................................4–6

FLS-4S............................................................................................................................................................................................4–7

FPS-10...........................................................................................................................................................................................4–7

JBT-9..............................................................................................................................................................................................4–7

MJ-47.............................................................................................................................................................................................4–8

PCS-1..............................................................................................................................................................................................4–8

PKD-1.............................................................................................................................................................................................4–8

RJ-56..............................................................................................................................................................................................4–8

RJ-74..............................................................................................................................................................................................4–9

SA-69.............................................................................................................................................................................................4–9

SPS-1...........................................................................................................................................................................................4–10

SPS-2...........................................................................................................................................................................................4–10

SRT-6...........................................................................................................................................................................................4–10

SS-15...........................................................................................................................................................................................4–10

SS-46...........................................................................................................................................................................................4–10

SS-68...........................................................................................................................................................................................4–11

ST-21...........................................................................................................................................................................................4–11

SX-4..............................................................................................................................................................................................4–11

XCS-4...........................................................................................................................................................................................4–11

XRS-6...........................................................................................................................................................................................4–12

Service concepts............................................................................................................................................................................4–12

Flash concept with FPS-10...................................................................................................................................................4–12

MJ-47 module jig concept....................................................................................................................................................4–13

POS (Point of Sale) flash concept.......................................................................................................................................4–14

Service concept for RF/BB testing and tuning...............................................................................................................4–15

CU-4 flash concept with FPS-10..........................................................................................................................................4–16

RF testing and BB testing/tuning concept......................................................................................................................4–17

LAN connection flash concept.............................................................................................................................................4–18

List of Tables

Table 8 Attenuations for RM-57..................................................................................................................................................4–9

Table 9 Attenuations for RM-58..................................................................................................................................................4–9

List of Figures

Figure 34 Basic flash concept with FPS-10...........................................................................................................................4–12

Figure 35 MJ-47 module jig service concept........................................................................................................................4–13

Figure 36 POS flash concept......................................................................................................................................................4–14

Figure 37 Service concept for RF/BB testing and tuning..................................................................................................4–15

Figure 38 CU-4 flash concept with FPS-10.............................................................................................................................4–16

Figure 39 RF testing and BB testing/tuning concept........................................................................................................4–17

Figure 40 LAN connection flash concept...............................................................................................................................4–18

Issue 1 Company Confidential Page 4–3

RM-57/58

Nokia Customer Care Service Tools and Service Concepts

(This page left intentionally blank.)

Page 4–4 Company Confidential Issue 1

RM-57/58 Service Tools and Service Concepts Nokia Customer Care

Service tools

List of Service Tools

The table below gives a short overview of service tools that can be used for testing, error analysis and repair of product , refer to various concepts.

AC-33 Power supply

Universal power supply for FPS-10; included in the FPS-10 sales package.

AD-18FS Flash adapter

AD-18FS has the following features:

• Provides galvanic connection to terminal test pads

• Provides standardized interface towards Control Unit

• Provides RF connection using galvanic connector or coupler Multiplexing between USB and FBUS media, controlled by Vusb

CA-31D USB cable

The CA-31D USB cable is used to connect FPS-10 or FPS-11 to a PC. It is included in the FPS-10 and FPS-11 sales packages.

Issue 1 Company Confidential Page 4–5

RM-57/58

Nokia Customer Care Service Tools and Service Concepts

CA-35S Power cable

The power cable CA-35S is used to power up the interface adapter SS-46.

CU-4 Control unit

CU-4 is a general service tool used with a module jig and a flash adapter. CU-4 requires an external 12 V power supply. The unit has the following features:

• software controlled via USB

• EM calibration function

• Forwards FBUS/Flashbus traffic to/from terminal

• Forwards USB traffic to/from terminal

• software controlled BSI values

• regulated VBATT voltage

• 2 x USB2.0 connector (Hub)

• FBUS and USB connections supported

DKU-2 USB connectivity cable

USB to Pop-PortTM connector cable.

Page 4–6 Company Confidential Issue 1

RM-57/58 Service Tools and Service Concepts Nokia Customer Care

FLS-4S Flash device

FLS-4S is a dongle and flash device incorporated into one package, developed specifically for POS use.

FPS-10 Flash prommer

FPS-10 interfaces with:

• PC

• Control unit

• Flash adapter

• Smart card

FPS-10 flash prommer features:

• Flash functionality for BB5 terminals

• Smart Card reader for SX-2 or SX-4

• USB traffic forwarding

• USB to FBUS/Flashbus conversion

• LAN to FBUS/Flashbus and USB conversion

• Vusb output switchable by PC command

FPS-10 sales package includes:

• FPS-10 prommer

• Power Supply with 5 country specific cords

• USB cable

JBT-9 Bluetooth test and

interface box (sales pack)

The JBT-9 test box is a generic device to perform Bluetooth bit error rate testing and doing cordless FBUS connection via Bluetooth. An ACP-8x charger is needed for BER testing and AXS-4 cable in case of cordless testing interface usage.

• JBT-9 testbox

• Installation and warranty information

Issue 1 Company Confidential Page 4–7

RM-57/58

Nokia Customer Care Service Tools and Service Concepts

MJ-47 Module jig

MJ-47 is meant for component level troubleshooting. The jig includes an RF interface for GSM, WCDMA and Bluetooth. In

addition, it has the following features:

• Provides mechanical interface with the engine module

• Provides galvanic connection to all needed test pads in module

• Multiplexing between USB and FBUS media, controlled by Vusb

• UI test interface

• MMC interface

• Duplicated SIM connector

• Audio components: IHF, MIC, earpiece

• Connector for control unit

•

Access for Pop-PortTM system connector

Note: In the picture CU-4 is connected to MJ-47 . CU-4 is not part

of the MJ-47 sales package and has to be ordered separately.

PCS-1 Power cable

The PCS-1 power cable (DC) is used with a docking station, a module jig or a control unit to supply a controlled operating voltage.

PKD-1 SW security device

SW security device is a piece of hardware enabling the use of the service software when connected to the parallel (LPT) port of the PC.

Without the device, it is not possible to use the service software. Printer or any such device can be connected to the PC through the device

if needed.

RJ-56 Rework jig

RJ-56 is a rework jig used with ST-21.

Page 4–8 Company Confidential Issue 1

RM-57/58 Service Tools and Service Concepts Nokia Customer Care

RJ-74 Soldering jig

RJ-74 is a soldering jig used for soldering and as a rework jig for the engine module.

SA-69 RF coupler

SA-69 is an RF coupler for GSM RF testing. It is used together with a product-specific flash adapter.

The following tables show the coupler attenuation values:

• Table 8 Attenuations for RM-57

GSM900 TX Att. (dB) GSM900 RX Att. (dB)

880 MHz 4.3 925 MHz 3.4

897 MHz 3.8 942 MHz 3.3

915 MHz 3.5 960 MHz 3.5

GSM1800 TX Att. (dB) GSM1800 RX Att. (dB)

1710 MHz 6.8 1805 MHz 6.1

1748 MHz 6.1 1843 MHz 6

1785 MHz 6.1 1880 MHz 6

GSM1900 TX Att. (dB) GSM1900 RX Att. (dB)

1850 MHz 6 1930 MHz 6.3

1880 MHz 6 1960 MHz 6.6

1910 MHz 6.2 1990 MHz 6.8

• Table 9 Attenuations for RM-58

GSM850 TX Att. (dB) GSM850 RX Att. (dB)

824 MHz 5.3 869 MHz 3.6

837 MHz 4.7 882 MHz 3.3

848 MHz 4.4 894 MHz 3.2

GSM1800 TX Att. (dB) GSM1800 RX Att. (dB)

1710 MHz 6.2 1805 MHz 6.2

1748 MHz 6 1843 MHz 6.2

1785 MHz 6.2 1880 MHz 6.2

GSM1900 TX Att. (dB) GSM1900 RX Att. (dB)

1850 MHz 6.2 1930 MHz 6.4

1880 MHz 6.2 1960 MHz 6.4

1910 MHz 6.3 1990 MHz 6.6

Issue 1 Company Confidential Page 4–9

RM-57/58

Nokia Customer Care Service Tools and Service Concepts

SPS-1 Soldering Paste

Spreader

SPS-2 Soldering paste

spreader

SRT-6 Opening tool

SS-15 Camera removal tool

The camera removal tool SS-15 is used to remove/attach the camera module from/to the socket on the phone PWB.

SS-46 Interface adapter

SS-46 acts as an interface adapter between the product-specific flash adapter and FPS-10.

Page 4–10 Company Confidential Issue 1

RM-57/58 Service Tools and Service Concepts Nokia Customer Care

SS-68 Antenna cover

opening tool

SS-68 is a tool for removing the antenna cover.

ST-21 Rework stencil

ST-21 is a rework stencil used with rework jig RJ-56.

SX-4 Smart card

SX-4 is a BB5 security device used to protect critical features in tuning and testing.

SX-4 is also needed together with FPS-10 when DCT-4 phones are flashed.

XCS-4 Modular cable

XCS-4 is a shielded (one specially shielded conductor) modular cable for flashing and service purposes.

Issue 1 Company Confidential Page 4–11

RM-57/58

Nokia Customer Care Service Tools and Service Concepts

XRS-6 RF cable

The RF cable is used to connect, for example, a module repair jig to the RF measurement equipment.

SMA to N-Connector ca. 610mm. Attenuation for:

• GSM850/900: 0.3+-0.1 dB

• GSM1800/1900: 0.5+-0.1 dB

• WLAN: 0.6+-0.1dB

Service concepts

Flash concept with FPS-10

Figure 34 Basic flash concept with FPS-10

Note: FPS-8 concept can also be used for flashing.

Item Type Description

1 AD-18FS Flash adapter

Page 4–12 Company Confidential Issue 1

RM-57/58 Service Tools and Service Concepts Nokia Customer Care

Item Type Description

2 SS-46 Interface adapter

3 CA-35S Power cable

4 XCS-4 Modular cable

5 CA-31D Standard USB A-B cable

6 FPS-10 Flash prommer box

7 CA-31D Standard USB A-B cable

8 PKD-1 SW security device

MJ-47 module jig concept

Legend

Module jig concept is meant for BB / RF testing + tuning and for flashing purposes.

Figure 35 MJ-47 module jig service concept

Item Type Description

1 MJ-47 Module jig

2 CU-4 Control unit

3 FPS-10 Flash prommer box

Issue 1 Company Confidential Page 4–13

RM-57/58

Nokia Customer Care Service Tools and Service Concepts

Item Type Description

4 SX-4 Smart card

5 XCS-4 Modular cable

6 PCS-1 DC power cable

7 CA-31D Standard USB A-B cable

8 CA-31D Standard USB A-B cable

9 GPIB control cable

10 XRS-6 RF cable

11 PKD-1 SW security device

POS (Point of Sale) flash concept

Figure 36 POS flash concept

Item Type Description

1 DKU-2 USB connectivity cable

2 FLS-4S POS flash device

Page 4–14 Company Confidential Issue 1

Nokia RM-57, RM-58 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Amendment Record Sheet

Copyright

Warnings and cautions

ESD protection

Care and maintenance

Company Policy

Battery information

Nokia 6681/6682 Service Manual Structure

RM-57/58 product selection

Product features and sales package

Product and module list

Mobile enhancements

Technical specifications

Transceiver general specifications

Main RF characteristics for triple-band (EGSM900/1800/1900 and GSM850/1800/1900) phones

Battery endurance

Environmental conditions

Parts lists

Mechanical spare parts list

RM-57 component parts list (1LF_09a)

Variant parts for RM-58

Component layouts

Component layout - bottom (1LF_09a)

Component layout - top (1LF_09a)

Phoenix installation steps in brief

Installing Phoenix

Updating Phoenix installation

Uninstalling Phoenix

Repairing Phoenix installation

Phoenix service software data package overview

Installing Phoenix data package

Uninstalling Phoenix data package

Configuring users in Phoenix

Managing connections in Phoenix

Installing flash support files for FPS-8 and FPS-10

Updating FPS-8 and FPS-10 flash prommer software

Activating FPS-8

Deactivating FPS-8

Service tools

List of Service Tools

Service concepts

Flash concept with FPS-10

MJ-47 module jig concept

POS (Point of Sale) flash concept