CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & SupportCONFIDENTIAL
2
Approved 1.0
MGR
10.Okt.2006
TABLE OF CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
INTRODUCTION 3
GENERAL REPAIR INFORMATION
PATHFINDER FOR WORKSHOP STAFF
EXPLODED VIEW AND COMPONENT DISPOSAL
SPARE PARTS OVERVIEW
LEVEL 2 SOLDER COMPONENTS
SPARE PARTS LIST
SERVICE TOOLS 1
SW-UPDATE 1
DISASSEMBLY INSTRUCTION (UPPER BLOCK) 1
DISASSEMBLY INSTRUCTION (LOWER BLOCK) 1
LEGEND FOR QUICK TROUBLE SHOOTER 2
QUICK TROUBLE SHOOTER PART 1 2
QUICK TROUBLE SHOOTER PART 2 2
QUICK TROUBLE SHOOTER PART 3 2
GONOGO TEST 2
BATTERY TEST 2
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & SupportCONFIDENTIAL
3
Approved 1.0
MGR
10.Okt.2006
INTRODUCTION1.
The purpose of this document is to help NOKIA service levels 1 and 2 workshop technicians to carry out service to NOKIA
products. This Service Manual is to be used only by authorized NOKIA service suppliers, and the content of it is confidential.
Please note that NOKIA provides also other guidance documents (e.g. Service Bulletins) for service suppliers, follow these
regularly and comply with the given instructions.
While every endeavor has been made to ensure the accuracy of this document, some errors may exist.
If you find any errors or if you have further suggestions, please notify NOKIA using the address below:
mailto:cc-ts-rc.documentation@nokia.com
Please keep in mind also that this documentation is continuously being updated and modified, so watch always out for
the newest version.
Warnings and Cautions
Please refer to the phone’s user guide for instructions relating to operation, care and maintenance including important
safety information. Note also the following:
Warnings:
CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS AND
1.
ANTI–SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF
NECESSARY, CONSULT THE VEHICLE DEALER/MANUFACTURER TO DETERMINE
THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF ENERGY.THE HANDPORTABLE TELEPHONE MUST NOT BE OPERATED
2.
IN AREAS LIKELY TO CONTAIN POTENTIALLY EXPLOSIVE ATMOSPHERES EG PETROL STATIONS (SERVICE STATIONS), BLASTING
AREAS ETC.
OPERATION OF ANY RADIO TRANSMITTING EQUIPMENT, INCLUDING CELLULAR TELEPHONES, MAY INTERFERE WITH THE
3.
FUNCTIONALITY OF INADEQUATELY PROTECTED MEDICAL DEVICES. CONSULT A PHYSICIAN OR THE MANUFACTURER OF THE
MEDICAL DEVICE IF YOU HAVE ANY QUESTIONS. OTHER ELECTRONIC EQUIPMENT MAY ALSO BE SUBJECT TO INTERFERENCE.
Cautions:
1. Servicing and alignment must be undertaken by qualified personnel only.
2. Ensure all work is carried out at an anti–static workstation and that an anti–static wrist strap is worn.
3. Use only approved components as specified in the parts list.
4. Ensure all components, modules screws and insulators are correctly re–fitted after servicing and alignment.
5. Ensure all cables and wires are repositioned correctly.
Electrostatic discharge can easily damage the sensitive components of electronic products.
Therefore every Service Supplier has to take care of all precautions, which are mentioned in the
service level related “Service Partner Requirements”, available on NOKIA Online. Also see ESD
Protection Requirements in this Service Manual.
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & SupportCONFIDENTIAL
4
Approved 1.0
MGR
10.Okt.2006
GENERAL REPAIR INFORMATION2.
In this section the technician will get some general hints how to carry out repairs:
To familiarize oneself with NOKIA product read the tutorials or user guide on www.nokia.com -->Support--> Phones, by
selecting the Phone Model.
Before starting the repair you must take care of ESD precautions like being in your ESD Protected Area and connecting your
wristband.
Use gloves to avoid corrosion and ngerprints.
Protect windows and displays with a lm to avoid dust and scratches.
When cleaning the LCD Module any lint-free cloth can be used (e.g. Micro-Fibre cloth).
When cleaning the pads you have to use a soft cloth/ESD brush and Isopropanol. It is not allowed to use a glass ber pencil
because it scratches the surface and will lead later on to corrosion.
Mechanical parts (except shielding lids and bent parts), which didn’t repair the failure, can be reused, if they are not
soldered.
When removing the shielding lids make sure to replace them with new ones, otherwise the high-frequency leakage can
have an inuence on the device.
Always use original NOKIA spare parts.
Check the soldering joints of the parts, which are concerned regarding the indicated error (e.g. soldered connectors or
switches) and resolder them if necessary (Level 2 only).
Remove redundant soldering ux after repair.
Meet the torque requirements when assembling the unit (see also the document “torques for transceiver assembly” on
NOKIA Partner Web Site/NOKIA Online).
Always use your own equipment for testing where you are sure that it works. E.g. if the customer complains about charger
function, please test the phone with your own charger to be sure if phone or charger causes the malfunction.
A SIM card is needed for all GoNoGo tests.
When doing the fault log entries, always note the Item code, which caused the malfunction. Also, ll in the appropriate
part code from the assembly, if needed.
Please be aware that some malfunctions could be software related and solved by an update.
There are several documents available on NOL, which have to be followed:
First, take care for the latest content pages of Service Bulletins, which are always available for each folder on NOKIA Online.
This is also important to recognize, if existing documents have become invalid.
The service level indicator at the bottom of each document tells the appropriate destination.
Downloads > Support Library >
1. Instructions
2. General Service Bulletins
3. Product related documents
4. Spare Part Service Bulletins
5. Service Tools Service Bulletins
6. Common Software Service Bulletins
etc,…
Use General SB-217 as a reference or overview.
Please also check NOKIA Online (NOL) for latest news and les on a regular basis.
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & SupportCONFIDENTIAL
5
Approved 1.0
MGR
10.Okt.2006
PATHFINDER FOR WORKSHOP STAFF3.
In addition to the information in this Service Manual, there are several instructions and information, which have to be
followed. Main documentation database is NOKIA Online with the purpose of serving different multimedia content, like
video clips or interactive tutorials.
It is mandatory to watch for newest technical and organizational information on a daily basis to be updated as required
(see “Latest files in Support Library”). Every new information has to be processed and implemented as soon as possible.
When logged into NOL you can also find needed information in different folder like:
Support Library
Phones
Service Manuals
Service Bulletins
Software
Repair Information
Level 1&2 e-learning (former NOKIA CarePoint) on NOKIA Online
Online Troubleshooting
Former NOKIA CarePoint
content, such as
•
Product information
•
Videos – Disassembly/Assembly
•
can be found on
NOKIA Online
NOKIA Online
Care Services
Training
Phone Models
Level 1&2 e-learning courses offer a quick overview of the NOKIA phone and support for how to repair and use the phone:
Overview & Guides
Basic information about the phone,
features and technologies
Disassembly & Assembly
Instructions how to disassemble and
assemble the phone
Troubleshooting
Step-by-step instructions on how to
locate and repair the most common
problems with the phone
To reduce the server traffic it is recommended to download newest version of huge files like videos, Phoenix packages or
Service Manuals only once and distribute it internally for further use.
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & SupportCONFIDENTIAL
6
Approved 1.0
MGR
10.Okt.2006
EXPLODED VIEW AND COMPONENT DISPOSAL4.
Recommendation for the ecologically friendly disposal of components. Colorized components show the different categories. See corresponding ITEM/CIRCUIT REF in the Spare Parts Service Bulletins on NOL.