Nokia 5300 Xpress Music, RM-147 User Manual

Download

Nokia 5300 Xpress Music User Guide

Remarque: La version française du guide se trouve à la page 89.

9254455

Issue 1a

DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION, declares that this RM-147 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at

http://www.nokiausa.com/phones/declaration_of_conformity/

0434

The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-of life. This applies to your device but also to any enhancements marked with this symbol. Do not dispose of these products as unsorted municipal waste. For more information, see product Eco-Declaration or country specific information at www.nokiausa.com

Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited.

Nokia, Visual Radio, Nokia Connecting People, XpressPrint, and Navi are trademarks or registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.

Nokia tune is a sound mark of Nokia Corporation.

Includes RSA BSAFE cryptographic or security protocol software from RSA Security.

Java is a trademark of Sun Microsystems, Inc.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

This product is licensed under the MPEG-4 Visual Patent Portfolio License (i) for personal and noncommercial use in connection with information which has been encoded in compliance with the MPEG-4 Visual Standard by a consumer engaged in a personal and noncommercial activity and (ii) for use in connection with MPEG-4 video provided by a licensed video provider. No license is granted or shall be implied for any other use. Additional information including that relating to promotional, internal and commercial uses may be obtained from MPEG LA, LLC. See http://www.mpegla.com

Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice.

This device complies with Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.

The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at any time without prior notice.

The availability of particular products may vary by region. Please check with the Nokia dealer nearest to you.

EXPORT CONTROLS

This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited.

FCC/INDUSTRY CANADA NOTICE

Your device may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC or Industry Canada can require you to stop using your telephone if such interference cannot be eliminated. If you require assistance, contact your local service facility. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Nokia could void the user's authority to operate this equipment.

Contents

For your safety.......................... 6

1. General information .......... 9

Access codes............................................ 9

Configuration settings service ........ 10

Download content.............................. 10

Digital rights management.............. 10

2. Get started....................... 12

Install SIM card and battery............ 12

Charge the battery.............................. 13

Memory card installation................. 13

Open the slide phone......................... 14

Switch the phone on and off........... 14

Antenna................................................. 15

Headset.................................................. 15

Phone strap........................................... 15

3. Your phone...................... 16

Keys and parts...................................... 16

Standby mode...................................... 17

Indicators and icons........................... 18

Flight mode........................................... 19

Keypad lock (keyguard)..................... 19

Functions without a SIM card......... 19

Folders.................................................... 27

Voice messages.................................... 27

Info messages ...................................... 28

Service commands.............................. 28

Delete messages.................................. 28

SIM messages....................................... 28

Message settings................................. 28

7. Phonebook ....................... 31

Search for a contact .......................... 31

Save names and phone numbers.... 31

Save details........................................... 31

Copy or move contacts...................... 31

Edit contact details............................ 32

Synchronize all.................................... 32

Delete contacts.................................... 32

Business cards...................................... 32

Settings.................................................. 33

Groups.................................................... 33

1-touch dials........................................ 33

Info, service, and my numbers........ 33

8. Log.................................... 34

9. Settings ............................ 35

4. Call functions.................. 20

Make a call ........................................... 20

1-touch dialing.................................... 20

Enhanced voice dialing...................... 20

Answer or decline a call.................... 21

Options during a call.......................... 21

5. Navigate the menus........ 22

6. Messaging........................ 23

Text messages...................................... 23

Picture message .................................. 25

Postcards............................................... 26

Nokia Xpress audio messaging........ 26

Memory full.......................................... 27

Profiles................................................... 35

Themes................................................... 35

Tones....................................................... 35

Display.................................................... 36

Time and date ...................................... 36

My shortcuts........................................ 37

Connectivity......................................... 38

Call.......................................................... 42

Phone...................................................... 42

Enhancements ..................................... 43

Configuration....................................... 43

Security.................................................. 44

Restore factory settings.................... 45

Phone software updates ................... 45

10. Operator menu ................ 47

11. Gallery.............................. 48

Print images.......................................... 48

Memory card......................................... 48

12. Media ............................... 50

Camera and video................................ 50

Media player......................................... 51

Music player.......................................... 51

Radio....................................................... 53

Voice recorder....................................... 54

Equalizer................................................. 55

Stereo widening................................... 55

13. Organizer.......................... 56

Alarm clock............................................ 56

Calendar................................................. 56

To-do list................................................ 57

Notes....................................................... 57

Calculator.............................................. 57

Countdown timer ................................ 58

Stopwatch ............................................. 58

14. Games and Applications .. 59

Launch a game..................................... 59

Launch an application........................ 59

Application options............................. 59

Download an application.................. 60

Contacts................................................. 63

Conversation options.......................... 63

Set your availability............................ 63

Log off service...................................... 64

16. SIM services...................... 65

17. Web................................... 66

Set up browsing................................... 66

Connect to a service........................... 66

Browse pages........................................ 67

Bookmarks............................................. 67

Appearance settings........................... 68

Security settings.................................. 68

Download settings .............................. 69

Service inbox ........................................ 69

Cache memory...................................... 69

Browser security.................................. 70

18. PC connectivity................ 72

Nokia PC Suite...................................... 72

Packet data, HSCSD, and CSD.......... 72

Bluetooth............................................... 72

Data communication applications... 73

19. Enhancements.................. 74

20. Battery information......... 75

Charging and discharging................. 75

Nokia battery authentication.......... 76

15. Instant messaging ........... 61

Begin an IM session............................ 62

Receive and reply to messages........ 62

Return to chat session ....................... 62

Care and maintenance ........... 78

Additional safety information.. 79

Index........................................ 84

For your safety

Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.

SWITCH ON SAFELY

Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger.

ROAD SAFETY COMES FIRST

Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.

INTERFERENCE

All wireless phones may be susceptible to interference, which could affect performance.

SWITCH OFF IN HOSPITALS

Follow any restrictions. Switch the phone off near medical equipment.

SWITCH OFF IN AIRCRAFT

Follow any restrictions. Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELING

Do not use the phone at a refueling point. Do not use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Follow any restrictions. Do not use the phone where blasting is in progress.

USE SENSIBLY

Use only in the normal position as explained in the product documentation. Do not touch the antenna unnecessarily.

QUALIFIED SERVICE

Only qualified personnel may install or repair this product.

ENHANCEMENTS AND BATTERIES

Use only approved enhancements and batteries. Do not connect incompatible products.

WATER-RESISTANCE

Your phone is not water-resistant. Keep it dry.

For your safety

BACK-UP COPIES

Remember to make back-up copies or keep a written record of all important information stored in your phone.

CONNECTING TO OTHER DEVICES

When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.

EMERGENCY CALLS

Ensure the phone is switched on and in service. Press the end key as many times as needed to clear the display and return to the start screen. Enter the emergency number, then press the call key. Give your location. Do not end the call until given permission to do so.

■ About your device

The wireless device described in this guide is approved for use on the GSM 850, 1800, and 1900 networks. Contact your service provider for more information about networks.

When using the features in this device, obey all laws and respect the privacy and legitimate rights of others.

When taking and using images or video clips, obey all laws and respect local customs as well as privacy and legitimate rights of others, including copyrights.

Warning: To use any features in this device, other than the alarm clock, the device must be switched on. Do not switch the device on when wireless phone use may cause interference or danger.

■ Network services

To use the phone you must have service from a wireless service provider. Many of the features in this device depend on features in the wireless network to function. These network services may not be available on all networks or you may have to make specific arrangements with your service provider before you can utilize network services. Your service provider may need to give you additional instructions for their use and explain what charges will apply. Some networks may have limitations that affect how you can use network services. For instance, some networks may not support all language-dependent characters and services.

Your service provider may have requested that certain features be disabled or not activated in your device. If so, they will not appear on your device menu. Your device may also have been specially configured for your network provider. This configuration may include changes in menu names, menu order and icons. Contact your service provider for more information.

For your safety

This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some features of this device, such as multimedia messaging (MMS), browsing, instant messaging, remote synchronization, and content downloading using the browser or MMS, require network support for these technologies.

■ Shared memory

The following features in this device may share memory: gallery, contacts, text messages, multimedia messages, and instant messages, e-mail, calendar, to-do notes, Java these features may reduce the memory available for the remaining features sharing memory. For example, saving many Java applications may use all of the available memory. Your device may display a message that the memory is full when you try to use a shared memory feature. In this case, delete some of the information or entries stored in the shared memory features before continuing. Some of the features, such as text messages, may have a certain amount of memory specially allotted to them in addition to the memory shared with other features.

games and applications, and note application. Use of one or more of

General information

1. General information

Congratulations on your purchase of this Nokia mobile phone. Some of its other features include a calendar, a clock, an alarm clock, a radio, a music player, and a built-in camera.

■ Access codes

Security code

The security code (5 to 10 digits) helps to protect your phone against unauthorized use. The preset code is 12345. To change the code, and to set the phone to request the code, see “Security,” p. 44.

PIN codes

The personal identification number (PIN) code and the universal personal identification number (UPIN) code (4 to 8 digits) help to protect your SIM card against unauthorized use. See “Security,” p. 44.

The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is required for some functions.

The module PIN is required to access the information in the security module. See “Security module,” p. 70.

The signing PIN is required for the digital signature. See “Digital signature,” p. 71.

PUK codes

The personal unblocking key (PUK) code and the universal personal unblocking key (UPUK) code (8 digits) is required to change a blocked PIN code and UPIN code, respectively. The PUK2 code (8 digits) is required to change a blocked PIN2 code. If the codes are not supplied with the SIM card, contact your local service provider for the codes.

Restriction password

The restriction password (4 digits) is required when using the Call restrictions. See “Security,” p. 44.

General information

■ Configuration settings service

To use some of the network services, such as mobile Internet services, MMS, Nokia Xpress audio messaging, or remote Internet server synchronization, your phone needs the correct configuration settings. For more information on availability, contact your network operator, service provider, nearest authorized Nokia dealer, or visit the support area on the Nokia Web site, www.nokiausa.com/support

When you have received the settings as a configuration message, and the settings are not automatically saved and activated, Configuration settings received is displayed.

To save the settings, select Show > Save. If required, enter the PIN code supplied by the service provider.

To discard the received settings, select Exit or Show > Discard.

■ Download content

You may be able to download new content, such as themes, tones, and video clips, to the phone (network service dependency). You may also be able to download updates of phone software (network service dependency). See “Phone,” p. 42, Phone updates.

For the availability of different services, pricing, and fees, contact your service provider.

Important: Use only services that you trust and that offer adequate security and protection against harmful software.

■ Digital rights management

Content owners may use different types of digital rights management (DRM) technologies to protect their intellectual property, including copyrights. This device uses various types of DRM software to access DRM-protected content. With this device you may be able to access content protected with WMDRM 10, OMA DRM

1.0, OMA DRM 1.0 forward lock, and OMA DRM 2.0. If certain DRM software fails to protect the content, content owners may ask that such DRM software's ability to access new DRM-protected content be revoked. Revocation may also prevent renewal of such DRM-protected content already in your device. Revocation of such DRM software does not affect the use of content protected with other types of DRM or the use of non-DRM-protected content.

General information

Digital rights management (DRM) protected content comes with an associated activation key that defines your rights to use the content.

If your device has OMA DRM protected content, to back up the content, use the backup feature of Nokia PC Suite.

If your device has WMDRM protected content, both the activation keys and the content will be lost if the device memory is formatted. You may also lose the activation keys and the content in case the files on your device get corrupted. Losing the activation keys or the content may limit your ability to use the same content on your device again. For more information, contact your service provider.

Get started

2. Get started

■ Install SIM card and battery

Always switch the device off and disconnect the charger before removing the battery.

Keep all SIM cards out of the reach of small children. For availability and information on using SIM card services, contact your SIM

card vendor. This may be the service provider, network operator, or other vendor. This device is intended for use with BL-5B battery. Always use original Nokia

batteries. See “Nokia battery authentication,” p. 76. To install the SIM card, do the following:

1. To remove the back cover of the phone, push the back cover release button (1), and detach the back cover away from the phone (2). Remove the battery as shown (3).

2. Open the SIM card holder (4), and insert the SIM card properly into the holder (5). Close the SIM card holder (6).

3. Replace the battery (7). Slide the back cover into its place (8, 9).

■ Charge the battery

Warning: Use only batteries, chargers, and enhancements approved by

Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous.

Get started

Check the model number of any charger before use with this device. This device is intended for use when supplied with power from an AC-3 or AC-4 charger.

For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any enhancement, grasp and pull the

plug, not the cord. Connect the charger to a wall socket and the lead

from the charger to the connector on the bottom of your phone.

If the battery is completely discharged, it may take a few minutes before the charging indicator appears on the display or before any calls can be made.

The charging time depends on the charger used. Charging a BL-5B battery with the AC-3 charger takes approximately 3 hours while the phone is in the standby mode.

■ Memory card installation

Keep all microSD memory cards out of the reach of small children. Use only compatible microSD cards with this device. Other memory cards, such as

reduced size multimedia cards, do not fit in the microSD card slot and are not compatible with this device. Using an incompatible memory card may damage the memory card as well as the device, and data stored on the incompatible card may be corrupted.

Get started

Insert a microSD card

1. Remove the back cover of the phone.

2. Insert the card into the microSD card slot with the contact surface facing backwards, and press it until it locks into place.

3. Close the back cover of the phone.

Use only microSD cards approved by Nokia for use with this device. Nokia utilizes the approved industry standards for memory cards but not all other brands may function correctly or be fully compatible with this device.

Remove the microSD card

Important: Do not remove the microSD card in the middle of an

operation when the card is being accessed. Removing the card in the middle of an operation may damage the memory card as well as the device, and data stored on the card may be corrupted.

1. Make sure that no application is currently accessing the microSD memory card.

2. Remove the back cover of the phone.

3. Press the microSD card slightly in to release the lock, and remove the microSD card from the slot.

■ Open the slide phone

To open the slide of the phone, push the upper part of the phone up.

■ Switch the phone on and off

Warning: Do not switch the phone on when wireless phone use is

prohibited or when it may cause interference or danger.

Press and hold the power key. See “Keys and parts,” p. 16. If the phone asks for a PIN or a UPIN code, enter the code (displayed as ****), and select OK.

Set the time and date

Enter the local time, select the time zone of your location in terms of the time difference with respect to Greenwich Mean Time (GMT), and enter the date. See “Time and date,” p. 36.

Get started

Plug and play service

When you switch on your phone for the first time, and the phone is in the standby mode, you may be asked to get the configuration settings from your service provider (network service dependency). Confirm or decline the query. See “Connect to support,” p. 44, and “Configuration settings service,” p. 10.

■ Antenna

Your device has an internal antenna.

Note: As with any other radio transmitting device, do not touch the antenna unnecessarily when the device is switched on. Contact with the antenna affects call quality and may cause the device to operate at a higher power level than otherwise needed. Avoiding contact with the antenna area when operating the device optimizes the antenna performance and the battery life.

■ Headset

The headset in the sales box has been approved by Nokia for use with this device. Always listen to music at a moderate level. Please be advised to pay special attention to volume level in case you connect any other headsets to the device.

Do not connect products that create an output signal, as this may cause damage to the device. Do not connect any voltage source to this connector.

Audio adaptor

Use an audio adaptor AD-50 to connect a headphone with a 3.5-mm plug to your phone. If the adaptor is connected to the phone the earpiece of the phone will be disconnected.

Please note that the adaptor does not support a microphone line.

■ Phone strap

Thread a strap through the eyelet of the phone as shown in the picture and tighten it.

Your phone

3. Your phone

■ Keys and parts

Earpiece (1) Music player, Radio, rewind, Scan Down (2) Music player, Radio, start, stop (3) Enhancements connector (4) Music player, Radio, fast forward, Scan up(5) Call key (6) Left, middle, and right selection keys (7) End key (8) Scroll keys (9) Keypad (10) Charger connector (11) USB connector (12) Power key (13) Phone strap eyelet (14) Camera lens (15) Volume up/ PTT key (16) Volume down (17) Camera key (18) Infrared port (19) Selfportrait viewfinder (20) Loudspeaker (21)

Your phone

■ Standby mode

When the phone is ready for use, and you have not entered any characters, the phone is in the standby mode.

Display

Signal strength of the cellular network (1) Battery charge status (2) Indicators (3) Network name or operator logo (4) Clock (5) Main screen (6) Function of left selection key (7) is Go to or a

shortcut to another function. See “Left selection key,” p. 37.

Function of middle selection key (8) is Menu. Function of right selection key (9) is Phonebk. or a shortcut to another

function. See “Right selection key,” p. 37. Operator variants may have an operator-specific name.

Active standby

In the active standby mode there is a list of selected phone features and information on the screen that you can directly access. To switch it on or off, select Menu > Settings > Display > Active standby > Active standby mode > On or Off.

In the standby mode, scroll up or down to activate the navigation in the list, and select Select or View. Left and right arrows at the beginning and end of a line indicate that further information is available by scrolling left or right. To end the active standby mode, select Exit.

To organize and change the active standby mode, activate the navigation mode, and select Options and from the available options.

Your phone

■ Indicators and icons

Your phone has two types of identifiers: indicators and icons.

Indicators

See “Standby mode,” p. 17 for information on indicators.

Icons

Icons are graphical representations of a specific item or situation. The following list describes each icon.

You have unread messages.

You have unsent, canceled, or failed messages.

The phone registered a missed call.

, Your phone is connected to the instant messaging service, and the

availability status is online or offline.

You received one or several instant messages.

The keypad is locked.

The phone does not ring for an incoming call or text message.

The alarm clock is activated.

The countdown timer is running.

The stopwatch is running.

, The phone is registered to the GPRS or EGPRS network.

, A GPRS or EGPRS connection is established.

, The GPRS or EGPRS connection is suspended (on hold).

A Bluetooth connection is active.

If you have two phone lines, the second phone line is selected.

All incoming calls are forwarded to another number.

The loudspeaker is activated, or the music stand is connected to the phone.

Calls are limited to a closed user group.

Your phone

The timed profile is selected.

, , , or

A headset, hands-free, loopset, or music stand enhancement is connected to the phone.

■ Flight mode

You can deactivate all radio frequency functionality and still have access to offline games, calendar, and phone numbers. Use the flight mode in radio sensitive environments—on board aircraft or in hospitals. When the flight mode is active, is shown.

Select Menu > Settings > Profiles > Flight > Activate or Customize. To deactivate the flight mode, select any other profile. In the flight mode you can make an emergency call. Enter the emergency number,

press the call key, and select Yes when asked Exit flight profile? The phone attempts to make an emergency call.

■ Keypad lock (keyguard)

To prevent the keys from being accidentally pressed, close the phone, and select Lock within 3.5 seconds.

To unlock the keypad, select Unlock > Ok, or open the phone. If the security keyguard is activated, enter the security code if requested.

To answer a call when the keyguard is on, press the call key or open the phone. When you end or decline the call, the keypad automatically locks.

For Security keyguard, see “Phone,” p. 42. When the keyguard is on, calls still may be possible to the official emergency

number programmed into your device.

■ Functions without a SIM card

Several functions of your phone may be used without installing a SIM card (for example, the data transfer with a compatible PC or another compatible device). Some functions appear dimmed in the menus and cannot be used.

For an emergency call, some networks may require that a valid SIM card is properly inserted in the device.

Call functions

4. Call functions

■ Make a call

1. Push the upper part of the phone up.

2. Enter the phone number, including the area code. For international calls, press

replaces the international access code), enter the country code, the area code without the leading 0, if necessary, and the phone number.

3. To call the number, press the call key. To increase the volume in a call, press + and to decrease, press - .

4. To end the call or to cancel the call attempt, press the end key, or close the phone.

To search for a name or phone number that you have saved in Phonebook, see “Search for a contact,” p. 31. Press the call key to call the number.

To access the list of dialed numbers, press the call key once in the standby mode. To call the number, select a number or name, and press the call key.

twice for the international prefix (the + character

■ 1-touch dialing

Assign a phone number to one of the 1-touch-dialing keys, 2 to 9. See “1-touch dials,” p. 33. Call the number in either of the following ways:

• Press a 1-touch-dialing key, then the call key.

•If 1-touch dialing is set to On, press and hold a 1-touch-dialing key until the call begins. See 1-touch dialing in “Call,” p. 42.

■ Enhanced voice dialing

You can make a phone call by saying the name that is saved in the contact list of the phone. Voice commands are language-dependent. To set the language, see Recognition lang. in “Phone,” p. 42.

Make a voice dialing call

Note: Using voice tags may be difficult in a noisy environment or

during an emergency, so you should not rely solely upon voice dialing in all circumstances.

Call functions

1. In the standby mode, press and hold the right selection key, or press and hold the volume down key. A short tone is played, and Speak now is displayed.

2. Say the voice command clearly. If the voice recognition is successful, a list with matches is shown. The phone plays the voice command of the match on the top of the list. If the result is not the correct one, scroll to another entry.

Using voice commands to carry out a selected phone function is similar to voice dialing. See Voice commands in “My shortcuts,” p. 37.

■ Answer or decline a call

To answer an incoming call, press the call key, or open the phone. To end the call, press the end key, or close the phone.

To decline an incoming call, press the end key. To mute the ringing tone, select Silence.

Call waiting

To answer the waiting call during an active call (network service dependency), press the call key. The first call is put on hold. To end the active call, press the end key.

To activate the Call waiting function, see “Call,” p. 42.

■ Options during a call

Many of the options that you can use during a call are network services. For availability, contact your service provider.

During a call, select Options and from the following options: Call options are Mute or Unmute, Phonebook, Menu, Lock keypad, Record,

Voice clarity, Loudspeaker or Handset. Network services options are Answer or Decline, Hold or Resume, New call,

Addtoconference, End call, End all calls, and the following: Touch tones — to send tone strings Swap — to switch between the active call and the call on hold Transfer calls — to connect a call on hold to an active call and disconnect yourself Conference — to make a conference call Private call —to discuss privately in a conference call

Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.

Navigate the menus

5. Navigate the menus

The phone offers you an extensive range of functions, which are grouped into menus.

1. To access the menu, select Menu. To change the menu view, select Options > Main menu view > List, Grid,

Grid with labels, or Tab. To rearrange the menu, scroll to the menu you want to move, and select

Options > Organize > Move. Scroll to where you want to move the menu, and select OK. To save the change, select Done > Yes.

2. Scroll through the menu, and select an option (for example, Settings).

3. If the selected menu contains further submenus, select the one that you want (for example, Call).

4. If the selected menu contains further submenus, repeat step 3.

5. Select the setting of your choice.

6. To return to the previous menu level, select Back. To exit the menu, select Exit.

Messaging

6. Messaging

You can read, write, send, and save text and picture messages, postcards, and voice notes. All messages are organized into folders.

■ Text messages

With the short message service (SMS) you can send and receive text messages, and receive messages that can contain pictures (network service dependency).

Before you can send any text or SMS e-mail message, you must save your message center number. See “Message settings,” p. 28.

To check SMS e-mail service availability and to subscribe to the service, contact your service provider. To save an e-mail address in Phonebook, see “Save details,” p. 31.

Your device supports the sending of text messages beyond the character limit for a single message. Longer messages will be sent as a series of two or more messages. Your service provider may charge accordingly. Characters that use accents or other marks, and characters from some language options like Chinese, take up more space limiting the number of characters that can be sent in a single message.

An indicator at the top of the display shows the total number of characters left and the number of messages needed for sending. For example, 673/2 means that there are 673 characters left and that the message will be sent as a series of 2 messages.

Text entry

To enter text (for example, when writing messages), use traditional or predictive text input. When you write text, press and hold Options to toggle between traditional text input, indicated by , and predictive text input, indicated by

. Not all languages are supported by predictive text input.

The character cases are indicated by , , and . To change the character case, press #. To change from the letter to number mode, indicated by

, press and hold #, and select Number mode. To change from the number to

the letter mode, press and hold #. To set the writing language, select Options > Writing language.

Messaging

Predictive text input

Predictive text input is based on a built-in dictionary to which you can also add new words.

1. Start writing a word using the keys, 2 to 9. Press each key only once for one letter.

2. When you finish writing the word and it is correct, to confirm it by adding a space, press 0.

If the word is not correct, press the list.

If the ? character is displayed after the word, the word you intended to write is not in the dictionary. To add the word to the dictionary, select Spell. Enter the word using traditional text input, and select Save.

To write compound words, enter the first part of the word, and press the scroll key right to confirm it. Write the last part of the word, and confirm the word.

3. Start writing the next word.

repeatedly, and select the word from

Traditional text input

Press a number key, 1 to 9, repeatedly until the desired character appears. The characters available depend on the selected writing language. If the next letter you want is located on the same key as the present one, wait until the cursor appears and enter the letter. The most common punctuation marks and special characters are available under the number key 1.

Write and send a message

1. Select Menu > Messaging > Create message > Text message.

2. Enter one or more phone numbers or e-mail addresses in the To: field. To retrieve a phone number or e-mail address from a memory, select Add.

3. For a SMS e-mail, enter a subject in the Subject: field.

4. Write your message in the Message: field.

5. To send the message, select Send. See “Message sending,” p. 25.

Read and reply to a message

1. To view a received message, select Show. To view it later, select Exit. To read the message later, select Menu > Messaging > Inbox.

Messaging

2. To reply to a message, select Reply > Text message, Picture message, or

Voice notes.

3. Write the reply message.

4. To send the message, select Send. See “Message sending,” p. 25.

■ Picture message

Note: Only devices that have compatible features can receive and

display multimedia messages. The appearance of a message may vary

depending on the receiving device. A multimedia message can contain some attachments. To check availability and to subscribe to the multimedia messaging service

(MMS, network service), contact your service provider. See “Message settings,” p. 28.

Write and send a picture message

The wireless network may limit the size of multimedia messages. If the inserted image exceeds this limit, the device may make it smaller so that it can be sent by MMS.

1. Select Menu > Messaging > Create message > Picture message.

2. Write your message. To add a file, select Insert and from the options.

3. To view the message before sending it, select Options > Preview.

4. To send the message, select Send. See “Message sending,” p. 25.

5. Enter one or more phone numbers or e-mail addresses in the To: field.

To retrieve a phone number or e-mail address from a memory, select Add.

6. To send the message, select Send. See “Message sending,” p. 25.

Message sending

To send the message, select Send. The phone saves the message in the Outbox folder, and the sending starts.

Note: When the phone is sending the message, the animated is shown.

This is an indication that the message has been sent by your device to the

message center number programmed into your device. This is not an

indication that the message has been received at the intended destination.

For more details about messaging services, check with your service provider. If an interruption occurs while the message is being sent, the phone tries to

resend the message a few times. If these attempts fail, the message remains in the Outbox folder. To cancel the sending of the messages in the Outbox folder, scroll to the desired message, and select Options > Cancel sending.

Messaging

Read and reply to a message

Important: Exercise caution when opening messages. Multimedia

message objects may contain malicious software or otherwise be harmful to your device or PC.

1. To view a received message, select Show. To view it later, select Exit.

2. To view the whole message if the received message contains a presentation,

select Play. To view the files in the presentation or the attachments, select Options >

Objects or Attachments.

3. To reply to the message, select Options > Reply > Text message, Picture

message, Postcard, Flash message, or Voice notes.

4. Write the reply message.

5. To send the message, select Send. See “Message sending,” p. 25.

■ Postcards

Before you can use the postcard service you must subscribe to the service. To check the availability, and costs, and to subscribe to the service if available, contact your network operator or service provider.

With the postcard messaging service (network service dependency), create and send postcards that may contain an image and a greeting text. The postcard is sent to the service provider using multimedia messaging. The service provider prints the postcard and sends it to the postal address given with the message. MMS must be activated before this service can be used.

To send a postcard, select Menu > Messaging > Create message > Postcard. Fill in the address, mandatory editor fields are marked by a *. Scroll to the image field, select Insert and an image from the gallery, or New image to insert a recent image; then write your greeting text. To send the message, select Send.

■ Nokia Xpress audio messaging

You can use the MMS to create and send an audio message in a convenient way. MMS must be activated before you can use audio messages.

Create a message

1. Select Menu > Messaging > Create message > Voice notes. The recorder

opens. To use the recorder, see “Voice recorder,” p. 54.

2. Speak your message.

Messaging

3. Enter one or more phone numbers in the To: field, or select Add to retrieve

anumber.

4. To send the message, select Send.

Listen to a message

To open a received audio message, select Play; or if more than one message is received, select Show > Play. To listen to the message later, select Exit.

■ Memory full

When you receive a message, and the memory for the messages is full, Memory full. Unable to receive messages. is shown. To first delete old messages, select

OK > Yes and the folder. Scroll to the desired message, and select Delete. If more messages are to be deleted, select Mark. Mark all the messages you want to delete, and select Options > Delete marked.

■ Folders

The phone saves received messages in the Inbox folder. Messages that have not yet been sent are saved in the Outbox folder. To set the phone to save the sent messages in the Sent items folder, see Save sent

messages in “General settings,” p. 28. To edit and send messages that you have written and saved in the Drafts folder,

select Menu > Messaging > Drafts. You can move your messages to the Saved items folder. To organize your Saved

items subfolders, select Menu > Messaging > Saved items. To add a folder, select Options > Add folder. To delete or rename a folder, scroll to the desired folder,

and select Options > Delete folder or Rename folder. Your phone has templates. To create a new template, save a message as a template.

To access the template list, select Menu > Messaging > Saved items > Templates.

■ Voice messages

The voice mailbox is a network service to which you may need to subscribe. For more information contact your service provider.

To call your voice mailbox, select Menu > Messaging > Voice mail > Listen to

voice mails. To enter, search for, or edit your voice mailbox number, select Voice mailbox no..

Messaging

If supported by the network, indicates new voice messages. To call your voice mailbox number, select Listen.

■ Info messages

You can receive messages on various topics from your service provider (network service dependency). For more information, contact your service provider. Select Menu > Messaging > Info messages and from the available options.

■ Service commands

Write and send service requests (USSD commands) to your service provider (such as activation commands for network services). Select Menu > Messaging > Serv. commands.

■ Delete messages

To delete messages, select Menu > Messaging > Delete messages > By message to delete single messages, By folder to delete all messages from a folder, or All messages.

■ SIM messages

SIM messages are specific text messages that are saved to your SIM card. You can copy or move those messages from the SIM to the phone memory, but not vice versa. To read SIM messages, select Menu > Messaging > Options > SIM messages.

■ Message settings

General settings

General settings are common for text and multimedia messages. Select Menu > Messaging > Message settings > General settings and from the

following options:

Save sent messages > Yes — to set the phone to save the sent messages in the Sent items folder

Overwriting in Sent > Allowed — to set the phone to overwrite the old sent

messages with the new ones when the message memory is full. This setting is shown only if you set Save sent messages > Yes .

Font size — to select the font size used in messages Graphical smileys > Yes — to set the phone to replace character-based smileys

with graphical ones

Messaging

Text messages

The text message settings affect the sending, receiving, and viewing of text and SMS e-mail messages.

Select Menu > Messaging > Message settings > Text messages and from the following options:

Delivery reports > On — to ask the network to send delivery reports about your messages (network service dependency)

Message centers > Add center — to set the phone number and name of the message center that is required for sending text messages. You receive this number from your service provider.

Msg. center in use — to select the message center in use Message validity — to select the length of time for which the network attempts

to deliver your message Messages sent via — to select the format of the messages to be sent: Text, Page,

or Fax (network service dependency)

Use packet data > Yes — to set GPRS as the preferred SMS bearer Character support > Full — to select all characters in the messages to be sent as

viewed. If you select Reduced, characters with accents and other marks may be converted to other characters.

Rep. via same center > Yes — to allow the recipient of your message to send you a reply using your message center (network service dependency)

Picture messages

The message settings affect the sending, receiving, and viewing of picture messages. You may receive the configuration settings for picture messaging as a configuration message. See “Configuration settings service,” p. 10. You can also enter the settings manually. See “Configuration,” p. 43.

Select Menu > Messaging > Message settings > Picture messages and from the following options:

Delivery reports > On — to ask the network to send delivery reports about your messages (network service dependency)

Image size (MMS) — to set the image size in picture messages. Default slide timing — to define the default time between slides in picture messages Allow p. msg receptn. > Yes or No — to receive or block the picture message. If

you select In home network, you cannot receive picture messages when outside your home network. The default setting of the picture message service is generally Yes. The availability of this menu depends on your phone.

+ 163 hidden pages

Nokia 5300 Xpress Music, RM-147 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual