Nokia Lumia 930, RM-1045 Service Manual

Service Manual for L1 and L2



Nokia Lumia 930

RM-1045

Key features

2.2 GHz Quad core processor 5" Full-HD OLED Display 32 GB Internal memory 20 MP Nokia PureView camera Integrated wireless charging

Version 1.0

CHECK THE REPAIR POLICY BEFORE PERFORMING ANY MECHANICAL REPAIR ON SERVICE LEVEL 1&2!

Send feedback

 Recommend Change in

KICS

 Rate this page in KICS  E-mail

careacademy@nokia.com

Exploded view Disassembly steps

More More

Assembly hints Solder components Service devices

More More More

Product controls and interfaces Service concept Phone reset

More More More

Service Manual Level 1 and 2

V

0

y

Nokia Lumia 930

RM-1045

ersion 1.

Version Date Description

1.0 29.05.2014 First published version

Version histor

Service Manual Level 1 and 2

Nokia Lumia 930

RM-1045 Version 1.0

Exploded view

CAMERA KEY

MAIN ANTENNA LTE

DAUGHTER PWB GASKET

EARPIECE GASKET

SKYPE CAMERA WINDOW GASKET

SKYPE CAMERA ASSEMBLY

JUMPER FLEX ADHESIVE

WATER INGRESS LABEL

I0007

COAX FLEX

I0005

LOCK KEY

I0008

VOLUME KEY

I0009

CHASSIS

I0004

I0016

I0015

HSJ ASSEMBLY

I0036

HSJ GASKET

I0037

VIBRA ASSEMBLY

I0019

VIBRA BOOT

I0021

SIM TRAY

I0001

I0018

I0017

EARPIECE

I0022

I0027

JUMPER FLEX

I0026

TYPE LABEL

I0040

LABEL TRAY

I0024

I0025

CARE UI ASSEMBLY

(I0002 - I0016)

DISPLAY WINDOW I0002

DISPLAY I0003

MAIN ANTENNA VOICE COAX FLEX I0006

BATTERY ADHESIVE I0010

SMALL BATTERY ADHESIVE I0011

PRIMARY MIC FLEX ADHESIVE I0014

PRIMARY MIC GASKET I0013

PRIMARY MIC FLEX I0012

VIBRA FLEX ADHESIVE I0020

CAMERA I0023

MIMO COAX FLEX I0028

MIMO COAX FLEX ADHESIVE I0029

BATTERY I0032

1

DAUGHTER PWB

I0035

LIGHT SWAP PACKAGE

(I0038 - I0040)

2

LIGHT SWAP PWB

I0038

LTE ADHESIVE

I0031

LTE RF COAX CABLE

I0030

Only available as assembly

HEAT SPREADER I0039

BATTERY CONNECTOR STRAP I0033

Not reuseable after removal

1/2

Repair/swap only in level 3

ENGINE COVER ASSEMBLY

(I0041 - I0045)

3

GPS/WLAN ANTENNA

MIMO ANTENNA

LED FLASH

NFC ANTENNA

BACK COVER ASSEMBLY

(I0046 - I0048)

4

BACK COVER GASKET

I0042

I0043

I0049

I0051

I0048

MAIN ANTENNA LTE I0044

MAIN ANTENNA VOICE I0045

IHF SPEAKER ASSEMBLY I0041

SCREW TORX+ SIZE 4 M1.4 X 3.8 I0034

WIRELESS CHARGING ASSEMBLY I0050

FLASH ADHESIVE

I0047

Only available as assembly

BACK COVER I0046

Not reuseable after removal

2/2

Repair/swap only in level 3

Service Manual Level 1 and 2

0

Nokia Lumia 93

RM-1045 Version 1.0

Disassembly steps

1) For disassembling you need the Nokia Standard toolkit version 2. You will also need the SS-311 back cover release tool, the SS-319 RF-connector disassembly/assembly tool and an AV jack.

Note that the device shown in most of these pictures is the Nokia Lumia Icon. On those steps the spare parts and the disassembly procedures are the same.

2) Protect the DISPLAY WINDOW with protective film.

3) Open the SIM TRAY with the SS-93 and pull it out.

4) At this point, if you only want to check the TYPE LABEL without having to disassemble the phone, you can pull the LABEL TRAY out with the hook on the SIM TRAY.

5) Release the BACK COVER with the SS-311 from the shown corner.

6) Remove the BACK COVER.

7) Unscrew the TORX+ SIZE 4 screw on top of the BATTERY CONNECTOR STRAP. Do not use the screw

again. Discard it.

8) Remove the BATTERY CONNECTOR STRAP with tweezers.

9) Disconnect the BATTERY connector with the SS-93. Be careful not to damage the connector.

10) Unscrew the ten TORX+ SIZE 4 screws in the order shown. Do not use the screws again. Discard them.

11) Release the ENGINE COVER ASSEMBLY from the shown place with the SS-93.

12) Lift up and remove the ENGINE COVER ASSEMBLY top end first. Be careful not to damage the antenna spring contacts on the bottom of the ENGINE COVER ASSEMBLY.

13) Remove the HEAT SPREADER with tweezers. Do not use it again. Discard it.

Note that the HEAT SPREADER needs to be removed completely ONLY when the ENGINE BOARD requires repair work.

14) Release the BATTERY from the shown place with the SS-93. Be careful not to damage the two flexes located under the BATTERY.

15) Remove the BATTERY.

16) Disconnect the SKYPE CAMERA connector from the shown edge with the SS-93. Be careful not to damage the connector or any components nearby.

17) Remove the SKYPE CAMERA with tweezers.

18) Disconnect the six shown connectors with the SS-93. Be careful not to damage the connectors or any components nearby.

Note that the SS-319 can also be used to disconnect the connectors.

19) Release the RF CABLE connector with the SS-319. Lock the SS-319 to the top of the connector as

shown and lift it up carefully. Be careful not to damage the connector.

20) Release also the other end of the RF CABLE and remove it.

21) Pull the LTE ADHESIVE to the direction shown to remove it under the LTE FLEX. Do not use it again.

Discard it.

22) Release the ENGINE BOARD from the shown place with the SS-93.

23) Lift up the other side and remove the ENGINE BOARD to the direction shown.

24) Disconnect the CAMERA connector from the shown edge with the SS-93. Be careful not to damage the connector or any components nearby. Remove the CAMERA.

25) Release the DAUGHTER ENGINE BOARD from the shown place with the sharp end of the SS-93.

26) Remove the DAUGHTER ENGINE BOARD.

27) Peel off the MIMO COAX FLEX with the SS-93.

28) Peel off the JUMPER FLEX with the SS-93.

29) If the UI ASSEMBLY or the flexes are being reused, peel off and discard any adhesive residue.

30) Release the EARPIECE with the SS-93 and remove it with tweezers.

31) Remove and discard the EARPIECE GASKET with the dental tool. Be careful not to injure yourself with

the sharp end of the dental tool.

32) Push out the LABEL TRAY with the SS-93 and remove it.

33) Use an AV jack to lift up the HSJ ASSEMBLY.

34) Release the HSJ ASSEMBLY flex with the SS-93 and remove the HSJ ASSEMBLY. Do not use it again. Discard it.

35) Remove the HSJ GASKET with tweezers.

36) Remove the VIBRA BOOT with tweezers.

37) Release the VIBRA and the VIBRA flex with the SS-93. Remove the VIBRA ASSEMBLY.

38) If the UI ASSEMBLY or the VIBRA ASSEMBLY are being reused, remove and discard any adhesive residue.

39) Remove and discard the DAUGHTER ENGINE BOARD GASKET only if it is damaged.

40) Release the PRIMARY MIC FLEX with the dental tool and remove it with tweezers. Do not use it again. Discard it.

41) Remove and discard the PRIMARY MIC FLEX ADHESIVE from the UI ASSEMBLY with tweezers.

42) Peel off and discard the SMALL BATTERY ADHESIVE using SS-93 and tweezers.

43) Peel off and discard the BATTERY ADHESIVE using SS-93 and tweezers

44) Release the WIRELESS CHARGING ASSEMBLY with the SS-93.

45) Remove the WIRELESS CHARGING ASSEMBLY. Do not use it again. Discard it.

46) Push the LED FLASH from the back side with the SS-93 and remove it with tweezers. Remove any adhesive remains from the LED FLASH.

47) Release the NFC ANTENNA with the SS-93. Start from the corner.

48) Remove the NFC ANTENNA. Do not use it again. Discard it.

49) Remove and discard the two BACK COVER GASKETS with tweezers.

50) The Nokia Lumia 930 disassembly procedure is complete.

-END OF DISASSEMBLY-

Service Manual Level 1 and 2

V

0

Nokia Lumia 930

RM-1045

ersion 1.

Assembly hints

Note that the device shown in most of these pictures is the Nokia Lumia Icon. On those steps the spare parts and the assembly procedures are the same.

1) To assemble the PRIMARY MIC FLEX, first place the PRIMARY MIC GASKET on the microphone. Make sure the shown hole aligns with the microphone hole.

2) Press gently to activate the adhesive and remove the protective film from the PRIMARY MIC GASKET.

3) Remove also the protective film from the PRIMARY MIC FLEX.

4) Place the PRIMARY MIC FLEX ADHESIVE to its slot in the UI ASSEMBLY. Use the shown holes to get the right alignment.

5) Press gently with the SS-93 to activate the adhesive and peel off the protective film.

6) Place the PRIMARY MIC FLEX to its place. Use the holes to get the right alignment. Press gently to activate the adhesive.

7) Place the BATTERY ADHESIVE as shown on the UI ASSEMBLY. Use the shown holes to get the right

alignment.

8) Press all around the ADHESIVE...

9) ... and peel off the protective film.

10) Place the SMALL BATTERY ADHESIVE as shown on the UI ASSEMBLY. Use the shown holes to get the right alignment.

11) Press all around the ADHESIVE...

12) ... and peel off the protective film.

13) Start assembling the VIBRA ASSEMBLY by first placing the VIBRA BOOT on it as shown.

14) Place the VIBRA ASSEMBLY to its slot on the UI ASSEMBLY. First align the flex to its place, then lower down the VIBRA.

15) Gently press the flex and the VIBRA from the shown place to activate the adhesive.

16) To assemble the MIMO COAX FLEX and the JUMPER FLEX, first place them on the SS-327 flex assembly jig. Use the guiding pins to get the right placement.

17) Place the MIMO COAX FLEX ADHESIVE on the MIMO COAX FLEX. Press firmly to activate the adhesive

and remove the protective film.

18) Place the JUMPER FLEX ADHESIVE on the JUMPER FLEX. Press firmly and remove the protective film.

19) Before placing the UI ASSEMBLY on the jig check once more that the flexes are positioned on the jig as

shown. Check also that the top side of the UI ASSEMBLY is facing the shown side of the jig as shown.

20) Then place the UI ASSEMBLY on the jig and press it gently but properly to get the flexes attached. Be careful not to damage the DISPLAY.

21) Remove the UI ASSEMBLY from the jig and check that the flexes are properly attached.

22) Assemble the DAUGHTER ENGINE BOARD to the UI ASSEMBLY shown side first. Align the two shown pogo pins to their places.

23) Then lower down the DAUGHTER ENGINE BOARD and press down to attach the shown clip. Be careful

not to damage the DAUGHTER ENGINE BOARD or any of its componets.

24) When assembling the CAMERA use the SS-327 flex assembly jig as a steady platform.

25) Connect the CAMERA to the ENGINE BOARD with the SS-93. Be careful not to damage the connector or

any components nearby.

26) Then fold the CAMERA flex as shown.

27) Start assembling the ENGINE BOARD to the UI ASSEMBLY shown side first and align the CAMERA to its

socket.

28) Lower down the ENGINE BOARD and press to attach the shown clip.

29) After assembling the ENGINE BOARD check the tactility of the side keys.

30) Place the LTE ADHESIVE to its place. Use the guiding lines on the ENGINE BOARD to get the right placement. Remove the protective film from the LTE ADHESIVE.

31) Place the SKYPE CAMERA GASKET to the shown slot on the SS-327 jig.

32) Place the SKYPE CAMERA on top of the gasket as shown and press it gently to activate the adhesive.

33) Remove the SKYPE CAMERA fom the jig and remove the protective film from the SKYPE CAMERA

GASKET.

34) Place the HEAT SPREADER on the ENGINE BOARD as shown. Use the edges of the shielding lids to get the right alignment.

35) Press all around the HEAT SPREADER to activate the adhesive.

36) Remove the protective film and gently press all around the HEAT SPREADER again to make sure its properly attached.

37) Fasten the ten TORX+ SIZE 4 screws in the order shown to the torque of 13 Ncm.

38) Fasten the TORX+ SIZE 4 screw to the top of the BATTERY CONNECTOR STRAP to the torque of 13 Ncm.

39) Assemble the BACK COVER to the UI ASSEMBLY bottom end first.

40) Press together the top end.

41) Then press together all the other sides of the device to get the BACK COVER completely attached.

Service Manual Level 1 and 2

Nokia Lumia 930

RM-1045 Version 1.0

TOP

Solder components

Grounding

Volume up

spring

S4403 S4402 S4401 S4400 X1002

X1004

Camera

fuse

F1401

HSJ

Connector

X2104

BOTTOM

switch

Volume down

switch

X1003

Grounding

spring

Power switch

Grounding

spring

EMI

Filter

Z3300

Grounding

spring

X1006

Camera

switch

Speaker -

Grounding

spring

USB

Fuse

V3310

Mic front

connector

X2103

X1001

Grounding

spring

GPS Ant

spring

X6304

NFC Ant

spring

NFC Ant

spring

charging spring

X6501

X6301 A1008

BT/WLAN

Ant spring

LTE Coax

cable clamp

Wireless

X3310

LTE Coax

cable clamp

X2105

Speaker +

spring

X2107

Mic back

connector

X2108

USB

EMI Filter

Z3301

X3311

Wireless

charging spring

Service Manual Level 1 and 2

V

0

Nokia Lumia 930

RM-1045

ersion 1.

CA-190CD Service cable AC-60 Fast USB charger SS-311 Back cover release tool

Service devices

SS-319 RF cable

disassembly/assembly tool

SS-327 Flex assembly jig Nokia Standard Toolkit (v2)

For more information, refer to the Service

Bulletin (SB-011) on Nokia Online. Supplier or

manufacturer contacts for tool re-order can be

found in “Recommended service equipment”

document on Nokia Online.

Service Manual Level 1 and 2

Nokia Lumia 930

RM-1045 Version 1.0

Product controls and interfaces

1

3

9

12

10 11

2

4 5

6

7

8

1 — Nano-SIM holder 2 — 3.5mm Headset connector 3 — Earpiece 4 — Front camera 5 — Ambient light & Proximity sensor 6 — 2nd Microphone 7 — Touch screen 8 — Home key

9 — Back key 10 — Search key 11 — Main microphone 12 — Micro-USB connector 13 — 3rd Microphone 14 — LED Flash 15 — Camera 16 — Volume keys 17 — Power/Lock key 18 — Camera key 19 — Loudspeaker 20 — 4th Microphone 21 — GPS/BT/WLAN Antenna area 22 — MIMO Antenna area 23 — NFC Area 24 — Wireless charging area 25 — Main Antenna area

13

14

20

15

16

17

18

19

21

23

24

25

22

Service Manual Level 1 and 2

Nokia Lumia 930

RM-1045 Version 1.0

Flashing concept

Service concept

Service

software

CA-101

Note: Charged battery is mandatory

Transceiver with

embedded battery

Service Manual Level 1 and 2

u

Nokia Lumia 930

RM-1045 Version 1.0

Phone reset

Hardware reset

If the phone hardware is jammed, you should first recommend that the consumer performs a hardware reset. The hardware reset does not reset the Windows Live ID or remove any consumer data. Because the consumer cannot remove the battery to reset the phone the phone has a special electronic circuit which cuts the phone power when power key is pressed for 10-15 seconds.

To perform the hardware reset, press and hold the Power key for about 10-15 seconds until a short vibration is felt. The phone should restart by itself.

Software / operating system (OS) reset

The software / operating system (OS) reset returns the phone to its out-of-the-box state. Note that this procedure erases all consumer data! Always first try to perform a hardware reset.

Option 1: About men

- Use this option if the consumer knows the lock code

- This option warns the consumer about data loss!

- Tap Settings > About > reset your phone

Option 2: Hardware key combination

- Use this option if the phone is locked and the consumer does not know the code

- Note: no warning about data loss!

- Do not advertise this feature to consumers!

Follow next steps to perform OS reset with phone keys.

Step 1

Make sure the phone is turned Off.

1. Press and hold the power key

2. Phone vibrates (release the power key)

3. Press and hold the volume down key

4. Exclamation mark is shown on the screen (release the volume down key)

Step 2

Input the following key combination:

1. Volume up

2. Volume down

3. Power

4. Volume down

Step 3

The phone will reset and boot up automatically

Nokia Lumia 930, RM-1045 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual