Nokia LPS-5 User Manual

Nokia Wireless Loopset LPS-5 User Guide

9214750

Issue 1 EN-US

DECLARATION OF CONFORMITY
Hereby, NOKIA CORPORATION declares that this LPS-5 product is in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/EC. A copy of the Declaration of Conformity can be found at
http://www.nokia.com/phones/declaration_of_conformity/.

© 2009 Nokia. All rights reserved.

Nokia, Nokia Connecting People and the Nokia Original Accessories logo are trademarks or
registered trademarks of Nokia Corporation. Other product and company names mentioned
herein may be trademarks or tradenames of their respective owners.

Reproduction, transfer, distribution, or storage of part or all of the contents in this document in
any form without the prior written permission of Nokia is prohibited.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

Nokia operates a policy of ongoing development. Nokia reserves the right to make changes and
improvements to any of the products described in this document without prior notice.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES
SHALL NOKIA OR ANY OF ITS LICENSORS BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME
OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES HOWSOEVER
CAUSED.

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED “AS IS”. EXCEPT AS REQUIRED BY
APPLICABLE LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS
OF THIS DOCUMENT. NOKIA RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW
IT AT ANY TIME WITHOUT PRIOR NOTICE.

The availability of particular products may vary by region. Please check with your Nokia dealer
for details.

Export controls
This device may contain commodities, technology or software subject to export laws and
regulations from the US and other countries. Diversion contrary to law is prohibited.

Issue 1 EN-US

Contents

1. Introduction ......................... 5

Bluetooth wireless technology........... 6

2. Get started ........................... 7

Keys and parts......................................... 7

Charge the battery ................................ 7

Switch the loopset on or off............... 8

Switch on.............................................. 8

Switch off............................................. 9

Pair and connect to another

device ........................................................ 9

Disconnect the loopset .................. 11

Reconnect the loopset ................... 11

3. Basic use............................. 12

Set up..................................................... 12

Adjust the loopset volume ............... 12

4

Adjust the sidetone volume ............. 12

Select vibration mode........................ 13

Calls ........................................................ 13

Manage two calls................................ 14

Listen to music..................................... 14

Clear settings or reset........................ 15

Troubleshooting................................... 15

4. Battery and charger

information ............................ 16

Care and maintenance........... 18

FCC/Industry Canada

notice...................................... 20

Introduction

1. Introduction

The Nokia Wireless Loopset LPS-5 is designed for people with hearing aids
to use their compatible mobile phone or music player together with a
telecoil (T-coil) equipped hearing aid.

When using the loopset for calling, you can speak directly into the
internal microphone, and you do not need to hold the phone near
your ear.

You can use this inductive loopset with compatible devices that support
Bluetooth wireless technology. The loopset wirelessly transmits sound
from the phone to a hearing aid that is in T mode. The quality of sound
depends on the type of hearing aid used and is affected by
electromagnetic disturbances from the surroundings.

Read this user guide carefully before using the loopset. Also, read the user
guide for the device that you connect to the loopset.

For the latest version of the user guide and additional information related
to your Nokia product, see www.nokia.com/support or your local Nokia
website. For more information about loopsets and other accessibility
solutions, see www.nokiaaccessibility.com (in English).

The product may contain small parts. Keep them out of the reach of
small children.

The surface of this device is nickel-free.

5

Introduction

■ Bluetooth wireless technology

Bluetooth wireless technology allows you to
connect compatible devices without cables.
The loopset and the other device do not need
to be in line of sight, but they should be within
10 metres (33 feet) of each other. The closer the
loopset and the other device are to each other,
the better the performance. The optimal
operating range is shown in dark grey in the
picture. The connection is subject to
interference from distance and obstructions (shown in light grey) or other
electronic devices.

The loopset is compliant with the Bluetooth Specification 2.1 + EDR
supporting the Headset Profile 1.1, the Hands-Free Profile (HFP) 1.5,
and the Advanced Audio Distribution Profile (A2DP) 1.0. Check with the
manufacturers of other devices to determine their compatibility with this
device.

<10m

6

Get started

2. Get started

■ Keys and parts

The loopset contains the following parts:

1. Neck loop

2. Indicator light (inside the rubber
sleeve at the top)

3. Volume keys

4. Microphone

5. Multifunction key

6. Charger connector

Before using the loopset, you must
charge the battery and pair the loopset
with a compatible device.

Parts of the device are magnetic. Metallic materials may be attracted to the device.
Do not place credit cards or other magnetic storage media near the device, because
information stored on them may be erased.

1

1

■ Charge the battery

Before charging the battery, carefully read “Battery and charger
information” p. 16.

2

4

11

3

5

6

7

Get started

Warning: Use only chargers approved by Nokia for use with this

particular model. The use of any other types may invalidate any approval
or warranty, and may be dangerous.

When you disconnect the power cord of any accessory, grasp and pull the plug, not
the cord.

1. Connect the charger to a wall outlet.

2. Connect the charger cable to the charger
connector. The indicator light is red during
charging.

Charging the battery fully may take up to
1 hour.

3. When the battery is fully charged, the
indicator light turns green. Disconnect the charger from the loopset,
then from the wall outlet.

The fully charged battery has power for up to 6 hours of talk time or up to
110 hours of standby time.

When the battery is discharged, the loopset beeps about every 5 minutes,
and the indicator light slowly flashes red.

■ Switch the loopset on or off

Switch on

To switch on, press and hold the multifunction key for about 2 seconds.
The loopset vibrates once and plays an ascending sequence of beeps, and

8

Get started

the green indicator light is displayed. The loopset tries to connect to the
last used device.

When the loopset is connected to your device and is ready for use, the
indicator light slowly flashes blue. If the loopset has not been paired with
a device, it automatically enters pairing mode (see “Pair and connect to
another device” p. 9).

Switch off

To switch off, press and hold the multifunction key for over 5 seconds.
The loopset vibrates twice and plays a descending sequence of beeps,
and the red indicator light is briefly displayed.

If the loopset is not connected to a paired device within about
30 minutes, it switches off automatically.

■ Pair and connect to another device

If your phone supports the A2DP Bluetooth profile and has a music player
feature, you can use the phone to also play music through the loopset.

If your phone does not support the A2DP Bluetooth profile, you can
separately pair the loopset with the phone and a music player that
supports this profile. If you have paired and connected the loopset to
your phone, disconnect the loopset before pairing the loopset with the
music player.

1. Ensure that your phone or music player is switched on.

9

Get started

2. To pair the loopset if it has not been previously paired with a device,
switch on the loopset. The loopset enters pairing mode, and the
indicator light quickly flashes blue.

To pair the loopset if it has been previously paired with another device,
ensure that the loopset is switched off, and press and hold the
multifunction key (for over 5 seconds) until the indicator light quickly
flashes blue.

3. Within about 5 minutes, activate the Bluetooth feature on your phone
or music player, and set it to search for Bluetooth devices. For details,
see the user guide of your device.

If the pairing is not initiated within about 5 minutes, the loopset
switches off.

4. Select the loopset (Wireless Loopset LPS-5) from the list of found
devices on your phone or music player.

5. If necessary, enter the passcode 0000 to pair and connect the loopset
to your device. If your device does not have a keypad, it may use this
passcode by default.

In some devices, you may need to make the connection separately
after pairing.

If pairing is successful, the loopset appears in the menu of your device
where you can view the currently paired Bluetooth devices.

When the loopset is connected to your device and is ready for use, the
indicator light slowly flashes blue.

10

Get started

You can pair the loopset with up to eight devices but connect it to only
one device at a time.

Disconnect the loopset

To disconnect the loopset from your device, switch off the loopset,
or disconnect it in the Bluetooth menu of your device.

You do not need to delete the pairing with the loopset to disconnect it.

Reconnect the loopset

If the loopset loses the connection to your device when it is switched on,
the loopset vibrates three times and beeps about once a minute.

To reconnect the loopset to the phone or music player that you have last
used with it, switch the loopset off and back on. Alternatively, if the
loopset is switched on, make the connection in the Bluetooth menu of
your device, or press the multifunction key. When the connection is
established, the loopset vibrates once and beeps twice.

You may be able to set your device so that the loopset connects to it
automatically. To activate this feature in a Nokia device, change the
paired device settings in the Bluetooth menu.

11

Basic use

3. Basic use

■ Set up

Ensure that the loopset is paired and
connected to your phone or music player.

Detach one end of the loop from the loopset,
place the loop around your neck, and plug the
loop end back into the loopset.

Switch your hearing aid to T mode.
Wear the loopset around your neck when you use it with your hearing aid.

■ Adjust the loopset volume

To adjust the strength of the magnetic field that the loopset produces for
the hearing aid, press a volume key during a call or while you listen to
music. The loopset vibrates (if vibration is enabled) and beeps at the
selected volume level, and the hearing aid changes the audio volume
accordingly.

■ Adjust the sidetone volume

Sidetone is the sound that is picked up by the loopset microphone and
routed to the hearing aid during a call.

To adjust the sidetone volume, press the multifunction key twice during a
call, and press a volume key within 15 seconds.

12

Basic use

■ Select vibration mode

You can set the loopset to vibrate in different situations.
To select the desired vibration mode during a call (when there is no other

call waiting or on hold), press and hold the multifunction key for about
2 seconds one or more times:

• If the loopset beeps once, the loopset vibrates when you press a key or
receive a call.

• If the loopset beeps twice, the loopset vibrates when you press a key.

• If the loopset beeps three times, the loopset vibrates when you receive
a call. This is the default setting.

• If the loopset beeps four times, the vibration is turned off.

■ Calls

To make a call, use your mobile phone in the normal way when the loopset
is connected to it.

To answer or end a call, press the multifunction key, or use the phone keys.
To reject a call, press the multifunction key twice. When you receive a call,
the loopset vibrates and plays a ringing tone, and the indicator light
quickly flashes blue.

To switch a call from the loopset to the connected device, switch the
loopset off, or use the related feature of your device (the loopset remains
switched on). To switch the call back to the loopset, switch the loopset on
(and connect it to your device), or if the loopset is switched on, press and
hold the multifunction key for about 2 seconds.

13