Nokia DT-600 User Manual

Nokia Charging Plate DT-600

1

6

2

2

3

4

5

Issue 1.2

7

10

8

9

11

© 2010 Nokia. All rights reserved.

Introduction

With the Nokia Charging Plate
DT-600, you can simultaneously
charge the battery in five compatible
devices.

The DT-600 device has three fixed
charging cables that can be stored
under the cover: two cables with a
Nokia 2.0 mm charger plug and one
cable with a micro-USB plug. In
addition, the device has two standard
USB connectors for the supplied
charging cables.

Use the supplied cables only with the
DT-600 device. Do not use any other
cables with it.

ENGLISH

Nokia, Nokia Connecting People and
the Nokia Original Accessories logo are
trademarks or registered trademarks of
Nokia Corporation.

Read this user guide carefully before
using the DT-600 device. Also, read
the user guide for the devices that
you charge with the DT-600 device.

This product may contain small parts.
Keep them out of the reach of small
children.

Warning: The aluminum
frame and plugs of this

device may contain a small
amount of nickel. Persons who are
sensitised to nickel may have
symptoms from prolonged skin
contact with the frame and the plugs.

Get started

The DT-600 device contains the
following parts shown on the title
page: power key (1), 2.0 mm charger
plugs (2), USB charger connectors (3),

indicator light (4), power connector
(5), and micro-USB charger
connector (6).

Select a cable for your device

To connect a fixed charging cable to
your compatible Nokia device, open
the cover by lifting it above the USB
connectors (7), and thread the desired
cables through the slots in the corners
of the cover (8).

To use a supplied USB charging cable,
select the correct cable for your
device. For details, see the user guide
of your device. Connect the cable to
either USB connector (9).

To store the fixed cables, open the
cover, and insert the cables into their
slots (10).

To store the USB charging cables that
you have connected to the DT-600
device, thread the cables through the
opening in a corner of the cover, and
place them on the cover.

ENGLISH

Charge the battery of your device

You can use the DT-600 device to
charge the battery in five devices at
the same time.

The micro-USB plug and the USB
connectors provide up to 1200 mA of
power. Make sure the device that you
connect to the plug or one of these
connectors supports this amount of
power. For details, see the user guide
of your device.

1. Connect the power cord to the
DT-600 device (11) and then to
the wall outlet.

2. Connect the charging cables of the
DT-600 device to your compatible
devices.

3. To switch on the DT-600 device,
press the power key. The blue
indicator light is displayed.

4. Check the charge level from the
connected device.

5. When the battery in the connected
device is fully charged, disconnect
the device from the charging cable.

6. When you are not using the
DT-600 device, press the
power key to switch it off.

Take care of your device

Handle your device and accessories with
care. The following suggestions help you
protect your warranty coverage.

• Keep the device dry. Precipitation,
humidity, and all types of liquids or
moisture can contain minerals that cor­rode electronic circuits. If your device
gets wet, allow it to dry completely.

ENGLISH

• Do not use or store the device in dusty
or dirty areas. Moving parts and elec­tronic components can be damaged.

• Do not store the device in high
temperatures. High temperatures can
shorten the life of the device and
warp or melt plastics.

• Do not store the device in cold
temperatures. When the device
warms to its normal temperature,
moisture can form inside the device
and damage electronic circuits.

• Do not attempt to open the device
other than as instructed in the user
guide.

• Do not drop, knock, or shake the
device. Rough handling can break
internal circuit boards and
mechanics.

• Only use a soft, clean, dry cloth to
clean the surface of the device.

• Do not paint the device. Paint can
clog the moving parts and prevent
proper operation.

ENGLISH

Recycle

Always return your used electronic prod­ucts, batteries, and packaging materials
to dedicated collection points. This way
you help prevent uncontrolled waste
disposal and promote the recycling of
materials. Check product environmental
information and how to recycle your
Nokia products at www.nokia.com/
werecycle, or with a mobile device,
www.nokia.mobi/werecycle.

The crossed-out wheeled-bin
symbol on your product, battery,
literature, or packaging reminds
you that all electrical and

electronic products, batteries,
and accumulators must be taken to
separate collection at the end of their
working life. This requirement applies in
the European Union. Do not dispose of
these products as unsorted municipal
waste. For more information on the
environmental attributes of your device,
see www.nokia.com/ecodeclaration.