Page 1

PAMS Technical Documentation
NSE–5 Series Transceivers
Disassembly Instructions
Amendment 07/00
Page 2

NSE–5
PAMS
Disassembly Instructions
Technical Documentation
[This page intentionally left blank]
Page 2
Amendment 07/00
Page 3

PAMS
NSE–5
Technical Documentation
Disassembly Instructions
1.Remove the Battery
2. Remove Dust Cap
3. Remove the Screws (4x)
4. Lift off B–Cover
note: snap fitting
Push B–cover down slightly
when lifting it off
Amendment 07/00
5. Pull out Antenna
note: snap fitting
Page 3
Page 4

NSE–5
PAMS
Disassembly Instructions
6. Remove the Screws (2x)
Technical Documentation
8. Remove the Slide Sensor Switch
9. Pull out the Slide until the End Stop
7. Lift off the PCB
Page 4
Amendment 07/00
Page 5

PAMS
NSE–5
Technical Documentation
10. Use a pair of Tweezers wih fine tips to push
the Slide Stopper Spring in the
direction indicated.
Disassembly Instructions
1 1. Simulateously with step 10:
Pull out the Slide past the
End Stop
! note: Pull out straight !
Handling the Slide Assembly:
! DO NOT handle the Slide like this ! ALWAYS handle the slide like this.
The Metal Slide is bent very easily when it is not protected by the phone.
Avoid bending of the Plungers at all times.
Amendment 07/00
Page 5
Page 6

NSE–5
PAMS
Disassembly Instructions
12. Bend open one side of
the (plastic) Slide Cover
and take out the Metal
Slide
Technical Documentation
! DO NOT !
Hold the Metal Slide like this.
The Metal Slide is bent very easily when it is not protected by the
phone. Avoid bending of the
Plungers at all times.
ALWAYS
Handle the Metal Slide like this.
The Metal Slide can be held by the
the Plungers.
Fitting a Metal Slide onto a Slide Cover:
Push the Metal Slide onto
the snap on one side of
the Slide Cover.
Push down the other
side, but do not hit the
middle snap.
Targa Bow
Push the Metal Slide onto
the snap on the opposite
side. A click should be
noticed.
or by one of
Page 6
Amendment 07/00
Page 7

PAMS
NSE–5
Technical Documentation
Disassembly Instructions
13. Remove the Display Assembly
14. Remove the Keymat Module
15. Remove the power keymat with the Speaker and Roller Key
Amendment 07/00
Page 7
Page 8

NSE–5
PAMS
Disassembly Instructions
16. ! Assemble the whole phone before fitting
the Slide Assembly !
The remaining assembly is done in the reverse
order of the disassembly.
17. Position the right hand Plunger onto
the start of the track and on the
Microphone Connector, as shown
Technical Documentation
Note Torque for screws 0.2Nm
18. Position the left hand Plunger onto the start of the track
and push the Slide Assembly into the phone.
! Push the Slide Assembly straight into the phone to
avoid bending of the Plungers !
Page 8
Amendment 07/00
Page 9

PAMS
NSE–5
Technical Documentation
Removing a Slide Cover Assembly
1
1. Hold the metal slide’s
plunger against the phone.
2. Bend open the slide
cover(plastic part)
2
3. Carefully rotate the slide cover
in the direction indicated
( Be careful of the middle snap)
Disassembly Instructions
3
4. Remove the slide
4
Mounting a Slide Cover Assembly
1
2
1. Make sure the metal slide
is pulled out until the end
stop (a double click can
be noticed).
2. Place the slide cover onto
the metal slide on the right
hand side ( where the mic
connector is located).
3. Rotate the slide cover
onto the metal slide.( make
sure the middle snap locates
properly by turning the
phone over to check).
4. Press the slide cover onto
the metal slide until it snaps
4
3
Check that all three snaps
(A,B.C) are in place.
C
B
A
Amendment 07/00
Page 9
Page 10

NSE–5
PAMS
Disassembly Instructions
Technical Documentation
[This page intentionally left blank]
Page 10
Amendment 07/00