NISSAN Altima Hybrid User Manual

2011 ALTIMA

NAVIGATION SYSTEM OWNER’S MANUAL

For your safety, read carefully and keep in this vehicle.

NISSAN NAVIGATION SYSTEM HELPDESK CONTACT INFORMATION

For assistance or inquiries about the NISSAN

contact the NISSAN NAVIGATION SYSTEM HELPDESK at:

● ADDRESS: P.O. Box 1588, Orem, UT 84059-992

●

www.nissan.ca

● PHONE: 1-888-661-9995

● HOURS: 6:00 AM to 5:00 PM

(Pacific Time)

NISSAN CONSUMER AFFAIRS DEPARTMENT

For assistance or inquiries about the NISSAN

the NISSAN Consumer Affairs Department at:

For U.S. customers Nissan North America, Inc. Consumer Affairs Department P.O. Box 685003 Franklin, TN 37068-5003 1-800-NISSAN-1 (1-800-647-7261)

For Canadian customers Nissan Canada Inc. 5290 Orbitor Drive Mississauga, Ontario L4W 4Z5 1-800-387-0122

Thank you for purchasing a NISSAN vehicle.

This user’s manual is for the navigation system only. This manual contains operating instructions for the NISSAN Navigation System offered in your NISSAN vehicle.

Please read this manual carefully to ensure safe operation of the navigation system.

● Because of possible specification changes and optional equipment, sections of this manual may not apply to your vehicle.

● All information, specifications and illustrations in this manual are those in effect at the time of printing. NISSAN reserves the right to change specifications or design at any time without notice.

● Do not remove this manual from the vehicle when selling this vehicle. The next user of this navigation system may need the manual.

FOREWORD

Navigation System, or to order updated map data warranty, service or general questions, contact

E-MAIL: Nissan-Navi-Info@navteq.com

WEB SITE: www. avigation.com or

Nissan

Table of

Introduction

Contents

Getting started

Map settings

Setting a destination

Route guidance

Storing a location/route

Viewing technical information

Other settings

Voice recognition

General system information

Troubleshooting guide

Index

1 Introduction

How to use this manual ............................1-2

For safe operation ..............................1-2

Reference symbols .............................1-2

Safety information .................................1-2

Laser product .....................................1-3

HOW TO USE THIS MANUAL SAFETY INFORMATION

This manual uses special words, symbols and icons that are organized by function.

Please refer to the following items to understand how to use this manual properly.

FOR SAFE OPERATION

WARNING



Indicates the presence of a hazard that could cause death or serious personal injury. To avoid or reduce the risk, the procedures must be followed precisely.

CAUTION

Indicates the presence of a hazard that could cause minor or moderate personal injury or damage to your vehicle. To avoid or reduce the risk, the procedures must be followed carefully.

NOTE:

Indicates items that help you understand and maximize the performance of your vehicle. If ignored, they may lead to a malfunction or poor performance.

REFERENCE SYMBOLS

INFO:

Indicates information that is necessary for efficient use of your vehicle or accessories.

Reference page:

Indicates the title and page that you should refer to.

MAP:

This is an example of how a button on the control panel will be shown.

“Route”:

This is an example of a key/item displayed on the screen.

Voice Command:

This indicates an operation by voice command.

This system is primarily designed to help you reach your destination, and it also performs other functions as outlined in this manual. However, you, the driver, must use the system safely and properly. Information concerning road conditions, traffic signs and the availability of services may not always be up-to-date. The system is not a substitute for safe, proper and legal driving.

Before using the navigation system, please read the following safety information. Always use the system as outlined in this manual.

WARNING



● To operate the navigation system, first park the vehicle in a safe location and set the parking brake. Operating the system while driving can distract the driver and may result in a serious accident.

● Do not rely on route guidance alone. Always be sure that all driving maneuvers are legal and safe in order to avoid accidents.

● Do not disassemble or modify this system. If you do, it may result in accidents, fire or electrical shock.

1-2 Introduction

LASER PRODUCT

● If you notice any foreign objects in the system hardware, spill liquid on the system or notice smoke or a smell coming from it, stop using the system immediately and contact a NISSAN dealer. Ignoring such conditions may lead to accidents, fire or electrical shock.

CAUTION

● Do not use this system if you notice any malfunctions such as a frozen screen or the lack of sound. Continued use of the system may result in accidents, fire or electrical shock.

● Some states/provinces may have laws limiting the use of video screens while driving. Use this system only where it is legal to do so.

● Extreme temperature conditions [below -4 °F (-20 °C) and above 158 °F (70 °C)] could affect the performance of the system.

NOTE:

Do not keep the navigation system running with the engine stopped. Doing so may discharge the vehicle battery. When you use the navigation system, always keep the engine running.

This navigation system is certified as a Class 1 laser product.

The navigation system complies with DHHS Rules 21 CFR Chapter 1, Subchapter J.

WARNING



● Do not disassemble or modify this system. There are no user serviceable parts in this navigation system.

● If maintenance, adjustments and operations other than those specified in this manual are attempted, injury due to laser radiation and exposure could occur.

Introduction 1-3

Required XM Radio威 and NavTraffic威 monthly subscriptions sold separately. XM NavTraffic威 only available in select markets. For more information, see www.xmradio.com/navtraffic.

Required XM Radio威 and NavWeather™ monthly subscriptions sold separately. XM NavWeather™ only available in select markets. For more information, see www.xmradio.com/navweather.

1-4 Introduction

2 Getting started

Control buttons and functions.......................2-2

Control panel ..................................2-2

Steering wheel switch. . . ........................2-3

Starting the system ................................2-4

Functions disabled while driving .....................2-4

Menu screen types and how to operate ..............2-6

Menu screens and their purposes ................2-6

Using controls to adjust values, levels, etc. ........2-6

Start menu. . . ..................................2-6

List screen. . . ..................................2-8

Touch screen operation ............................2-9

Selecting the item ..............................2-9

Adjusting the volume and others .................2-9

Scrolling the message or list ....................2-10

Inputting letters and numbers ...................2-10

How to input letters and numbers ..................2-10

Character (letters and numbers) input

screen .......................................2-10

Number input screen...........................2-12

Map menu screen ................................2-13

Current location map screen ....................2-14

Scrolled location map screen ...................2-14

Storing your home location/address ................2-15

How to store home location.....................2-15

Setting a destination ..............................2-18

Searching for a destination .....................2-18

Starting route guidance ........................2-19

Canceling a route .............................2-21

Operating maps ..................................2-22

How to view map screen .......................2-22

Setting the voice guidance ........................2-23

Turning voice guidance on/off ...................2-23

Adjusting voice guidance volume ................2-24

NISSAN voice recognition .........................2-25

Using the system ..............................2-26

Before starting ................................2-26

Giving voice commands ........................2-26

Command list .................................2-28

CONTROL BUTTONS AND FUNCTIONS

CONTROL PANEL

MAP:

䊐

Press to display the map. While following programmed route, press multiple times to change the type of route information.

DEST:

䊐

Press to enter a destination. Various methods for entering a destination are available.

“4. Setting a destination”.

ROUTE:

䊐

Press and hold to hear the current route guidance (guidance cancellation, route priority, way point setting on the route, etc.).

INFO:

䊐

Press to display the vehicle, traffic, weather or voice recognition information.

SETTING:

䊐

Press to access the system settings.

WNV0563

䊐

If the “Back” key needs to be touched to apply the setting on a settings screen, this manual will explicitly include a step for this procedure. Otherwise, touching the “Back” key returns the display to the previous screen.

The layout of the control panel switches may vary depending on the vehicle model and equipment.

DAY/NIGHT:

Press to switch between the day screen (bright) and the night screen (dark) . Press and hold to turn off the display. Press again to turn on the display.

INFO:

2-2 Getting started

STEERING WHEEL SWITCH

SOURCE:

䊐

Use to switch the audio mode (source). For additional information, see the Owner’s Manual.

ENTER:

䊐

Move up or down to highlight an item on the screen or adjust a setting. Press to select the highlighted item.

If this button is pressed while a map is

LNV0423

displayed, the map menu screen is displayed.

“MAP MENU SCREEN” (page 2-13)

Press and hold to display the start menu.

“START MENU” (page 2-6)

If this button is moved up while the audio function is activated and the map or status screen is displayed, the audio system can be operated.

䊐

Press this button during a setting operation to return to the previous screen. In certain screens, this button can also be used to apply the setting. This button will only work when the “Back” key is shown on the screen.

䊐

Use to adjust the volume. These buttons have the same function as that of the volume knob. For additional information, see the Owner’s Manual.

䊐

Press to start the voice recognition mode. If the voice recognition mode is already activated, pressing this button interrupts the voice guidance and you can speak a voice command immediately.

䊐

Use to enable Bluetooth姞 Hands-Free Phone system. For additional information, see the Owner’s Manual.

–or+:

Getting started 2-3

STARTING THE SYSTEM FUNCTIONS DISABLED WHILE DRIV-

ING

The navigation system starts when the ignition switch is turned to the ACC or ON position.

NOTE:

Do not keep the navigation system on with the engine stopped. Doing so may discharge the vehicle battery. When you use the navigation system, always keep the engine running.

When the driver wants to operate the navigation system, first park the vehicle in a safe location and set the parking brake. Operating the system while driving can distract the driver and may result in a serious accident.

WARNING



2-4 Getting started

Park the vehicle in a safe location and then operate the navigation system.

To ensure safe driving, some functions cannot be operated or have limited operation while driving.

The on-screen functions that are not available

NGT0019

while driving will be “grayed-out” or muted.

Getting started 2-5

MENU SCREEN TYPES AND HOW TO OPERATE

MENU SCREENS AND THEIR PURPOSES

Press the DEST, ROUTE, INFO, or SETTING button to display the corresponding menu screen.

How to select a menu item

Example: DEST screen

1. Select the preferred menu item by touching the corresponding key on the screen. The next screen is displayed.

2. Press BACK to return to the previous screen without applying any changes.

3. Press MAP to return to the current location map screen without applying any changes.

INFO:

● Depending on the menu selected, pressing MAP may not return the display to the current location map screen.

● An item can also be selected by moving the steering wheel switch up and down.

USING CONTROLS TO ADJUST VALUES, LEVELS, ETC.

There are two main methods to control the navigation system: the touch panel and the steering wheel switch. Use these controls to adjust the volume of phone and voice guidance, the display brightness, etc.

How to adjust

1. Select the preferred setting item and press SELECT. The color of the corresponding adjustment item changes.

2. Use one of the controls to increase or decrease the indicated value.

3. Press SELECT or BACK to apply the setting.

INFO:

● The volume of phone and voice guidance, the display brightness, etc. can be adjusted by moving the ENTER switch on the steering wheel up and down.

● These same adjustments can also be performed using the touch panel operation.

“ADJUSTING THE VOLUME AND OTHERS” (page 2-9)

START MENU

While in the map view, the start menu can be displayed using the steering wheel switch.

2-6 Getting started

NGT0023

1. Press and hold ENTER on the steering wheel switch.

2. Select the preferred item and push ENTER.

INFO:

ENTER on the steering wheel switch can be used to display the start menu only when the map or status screen is displayed.

Available items

● “Destination”: Displays the destination screen. It is the same screen that appears when DEST is pushed.

“4. Setting a destination”

● “Route”: Displays the route screen. It is the same screen that appears when ROUTE is pushed.

“5. Route guidance”

● “Info”: Displays the information screen. It is the same screen that appears when INFO is pushed.

“7. Viewing technical information”

● “Settings”: Displays the settings screen. It is the same screen that appears when SETTING is pushed.

“8. Other settings”

Getting started 2-7

When the list is sorted by the shortest

䊐

distance, the selected location can be confirmed in the preview on the right side of the screen.

Select REFINE to modify search conditions.

䊐

LIST SCREEN

After searching for a point of interest, a list screen is displayed.

Depending on the list displayed, it can be sorted.

Items displayed in a list:

Select the preferred item from the list. If a lo-

䊐

cation or facility name is not completely displayed (due to length), highlight the item with the steering wheel switch to display the hidden part of the name.

Distance from the current location

䊐

2-8 Getting started

Direction to the point of interest

䊐

If the entire list cannot be displayed on the

䊐

screen, the system displays the total number of items in the list and the entry number of the selected item. Touch the page down arrow to scroll the list.

An item that starts with the selected letter

䊐

will be displayed at the top of the list.

Select SORT to sort the list in the original

䊐

order.

NGT0024

TOUCH SCREEN OPERATION

Here, the operation examples performed with the touch panel operation are described.

NGT0025 NGT0026

SELECTING THE ITEM

When the item is touched, the next screen is displayed.

ADJUSTING THE VOLUME AND OTHERS

Touch “+” or “-” located on the right and left of the bar graph to perform the adjustment.

Getting started 2-9

LNV2007 NGT0028

SCROLLING THE MESSAGE OR LIST

Touch the up arrow to scroll up the page one item at a time, or touch the double up arrow to scroll up an entire page.

Touch the down arrow to scroll down the page one item at a item , or touch the double down arrow to scroll down an entire page.

HOW TO INPUT LETTERS AND NUMBERS

CHARACTER (letters and numbers) INPUT SCREEN

When setting a destination, searching for a facility or editing the stored locations, etc. alphanumeric characters must be entered into the system.

INPUTTING LETTERS AND NUMBERS

1. Touch the letter or number.

2. To delete a character, touch “Delete”. Touch and hold “Delete” to delete all of the characters.

2-10 Getting started

LNV0564 LNV0565 LNV0566

1. Use the touch panel to select a character on the displayed keyboard.

2. Select the desired character. The highlighted character is entered.

3. Select “Delete” to delete the last character entered.

Touch and hold “Delete” to delete all the characters entered.

Select “Space” to enter a space.

Getting started 2-11

LNV0567

4. After finishing the entry, select “List”.

INFO:

● When “Back” is touched on the screen, the screen returns to the previous screen even when characters have been entered.

● When text has been entered and the number of matching list items has been narrowed down enough so that they fit on the screen, the list screen appears automatically.

2-12 Getting started

Symbol input screen

LNV0568

● Symbol keys are displayed by selecting “Symbols”. Alphabet keys are displayed by selecting “A - Z”.

NUMBER INPUT SCREEN

A phone number or a street number can also be entered as a search method to look for a destination.

INFO:

Only the locations included in the map data database can be searched for by a phone number.

NGT0059

1. Use the touch screen to select a number on the displayed keyboard.

NGT0061 NGT0062

2. Select “Delete” to delete the last number entered.

Touch and hold “Delete” to delete all the numbers entered.

MAP MENU SCREEN

Select the map menu key while the current location map screen or a scrolled map screen is displayed to display the menu corresponding to that screen.

This menu can be used to access helpful functions quickly, such as setting a destination and searching for points of interest nearby.

“MENU SCREEN TYPES AND HOW TO OPERATE” (page 2-6)

3. After finishing the entry, select “List”.

INFO:

● When “Back” is touched on the screen, the screen returns to the previous screen even when numbers have been entered.

Getting started 2-13

NGT0029 NGT0030

CURRENT LOCATION MAP SCREEN

If the “Map Menu” key is touched while the current location map screen is displayed, the following options are available.

● “Store Location”: Store the current vehicle location in the Address Book. The stored location can be retrieved as necessary to set it as a destination (waypoint).

“STORING A LOCATION” (page 6-2)

● “Nearby Places”: Search for points of interest near the current vehicle location, such as restaurants and gas stations, etc.

“Finding a nearby place” (page 4-7)

2-14 Getting started

● “Map View”: Perform map operations such as the switching of map type and the setting of map orientation and scale.

“MAP TYPES” (page 3-2)

● “Map Icons”: Display certain points of interest near the current vehicle location on the map, such as restaurants and gas stations, etc.

“DISPLAYING MAP ICONS” (page 3-21)

● “Store Tracking”: Store in the Address Book the route travelled from the starting point to the current location.

“STORING A TRACKED ROUTE” (page 6-9)

SCROLLED LOCATION MAP SCREEN

If the “Map Menu” key is touched while a scrolled map screen is displayed, the following options are available.

● “New Dest”: Set the destination to the map location where the screen was touched. If a destination is already set, the location will be set as the new destination.

“SETTING A POINT ON THE MAP” (page 4-32)

STORING YOUR HOME LOCATION/ADDRESS

● “Add to Route”: Set the map location where the screen was touched to set a destination or a waypoint. This is available only when the suggested route is already set.

“Setting a destination or waypoint” (page 5-19)

● “Nearby Places”: Search for points of interest near the map location where the screen was touched and set them as a destination or waypoint.

Use the same search method as the one for places.

⬙FINDING A NEARBY PLACE” (page 4-7)

● “Store Location”: Store in the address book the map location where the screen was touched. The stored location can be retrieved to set it as a destination or waypoint.

⬙STORING A LOCATION” (page 6-2)

● “Delete”: Delete a stored location, destination or waypoint. To delete it, place the cross pointer over the corresponding icon.

● “Incident Detail”: Display the details of the traffic information icon. This function can be selected only when the traffic information icon is displayed. Place the cross pointer over the icon you want to check.

INFO:

Please note that incident details are a feature of Traffic Information, and that an XM NavTraffic姞 subscription is required in order to receive Traffic Information.

HOW TO STORE HOME LOCATION

If a home location is already stored in the Address Book, it can be easily retrieved to set the route to the stored home location.

The procedure to store the home location is the same as for storing any other location.

“4. Setting a destination”

As an example, the procedure for storing the home location by searching for a destination by address is described here.

Getting started 2-15

1. Press DEST.

2. Select “Home (Add New)”.

2-16 Getting started

NGT0031 NGT0032 NGT0033

3. A confirmation message is displayed. Confirm the contents of the message, select “Yes”.

4. Select “Street Address”. A character input screen is displayed.

NGT0034 NGT0035 NGT0036

5. Enter the address of the home location, select “OK”.

The map screen is displayed.

“FINDING AN ADDRESS” (page 4-5)

6. Touch the screen to adjust the home location if necessary. Select “OK”.

7. A message is displayed and the home location is stored.

Getting started 2-17

NGT0066 NGT0037

8. Select “OK”.

9. Press “Map” to return to the current location map screen. The home icon is displayed on the map.

INFO:

The same setting can also be performed by pressing SETTING and selecting “Navigation”.

“STORING A LOCATION BY SEARCHING” (page 6-2)

SETTING A DESTINATION

SEARCHING FOR A DESTINATION

As an example, the method for setting a restaurant as the destination using “Places” is described here.

1. Press DEST.

2. Select “Places”.

2-18 Getting started

NGT0038 NGT0039 NGT0040

3. Select “Nearby RESTAURANT”.

INFO:

The search can be narrowed down by selecting “All Categories or Name” or “ZAGAT” on this screen.

By selecting “All Categories or Name”, the area, name of facility, etc. can be further specified. By selecting “ZAGAT”, restaurants registered in the ZAGAT姞 database can be searched and sorted by its rating regarding food, decor, cost, and service.

4. Select the preferred restaurant from the list.

INFO:

● The position of the selected location is displayed in the preview on the right side of the screen.

● If there is a route already in progress, only places along the current route will be listed. Turn off “Show Along Route” at the top of list to display all nearby places.

5. The entire route is shown on the map. Select “Start” after confirming the location of the displayed destination.

INFO:

● The system sets the destination to the selected location and starts calculating a route.

● Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc. if necessary.

“PROCEDURES AFTER SETTING A DESTINATION” (page 5-2)

STARTING ROUTE GUIDANCE

After setting the destination and performing route calculation, the suggested route is displayed.

Getting started 2-19

NGT0040 NGT0042 NGT0043

1. Select “Start”. 2. Once route guidance is started, the system navigates through the guide points using visual and voice guidance.

2-20 Getting started

3. When approaching a guide point, the system automatically changes to the split screen and shows an enlarged view of the intersection in the left screen.

Press MAP to switch to the full map screen.

NGT0044 NRG0019 NGT0046

4. When arriving at the destination, route guidance automatically ends.

CANCELING A ROUTE

Delete a route that is already set according to the following procedure.

1. Press ROUTE.

2. Select “Cancel Route”.

3. A confirmation message is displayed. Select “Yes”.

INFO:

● If a route is cancelled, “Cancel Route” changes to “Resume Route”. Select “Resume Route” to reactivate the cancelled route. This is available only until a new route is set or a currently set destination is deleted.

● The above step does not delete the destination that has been set. To delete a destination, press DEST and select “Delete Destination”.

⬙DELETE DESTINATION” (page 4-33)

Getting started 2-21

OPERATING MAPS

HOW TO VIEW MAP SCREEN

The navigation system displays various information on the map screen.

Screen information

䊐

Vehicle icon:

Indicates the current vehicle location and the direction of travel.

Starting point:

Displays the vehicle location, with which the route is set, as the starting point.

2-22 Getting started

䊐

Guide point:

Indicates a guide point on the route.

Waypoint:

Displays locations between the starting point and the destination. A maximum of 5 waypoints can be set.

Destination:

Indicates the destination location of the route guidance.

LNV0569

When you reach your destination, the address will be displayed on the map screen.

Suggested route:

䊐

Appears in bold yellow during route guidance.

䊐

Map menu icon:

Touch the icon to display the Map Menu screen.

“MAP MENU SCREEN” (page 2-13)

/ Direction indicator:

Indicates the setting of the map: north always pointing up or the vehicle’s direction always pointing up on the display. Touch the icon to change this setting.

Scale indicator:

Indicates the scale of the map.

Touch the icon to display the scale bar. This allows the map scale to be adjusted.

“OPERATING WITH THE TOUCH OPERATION” (page 3-5)

Street name:

Displays the name of the street that the vehicle is currently driving on.

+ 285 hidden pages