if so equipped) ..................................................19
Bluetooth
®
Universal Transceiver (if so equipped) .....................18
®
Hands-free Phone System (vehicles without navigation -
®
Hands-free Phone System (vehicles with navigation -
if so equipped) ..................................................22
NISSAN Voice Recognition System (vehicles with navigation -
if so equipped) ..................................................25
Navigation System (if so equipped) .................................30
This easy-to-use Quick Reference Guide is intended to help you more fully
appreciate some of the unique features and functions of your new vehicle.
However, it is not intended to replace your Owner’s Manual. The Owner’s
Manual contains more detailed information to help you better understand
the important safety warnings, features, operation and maintenance of your
vehicle. All information, specifications, photographs and illustrations in this
publication are those in effect at the time of printing. NISSAN reserves the
right to change specifications or design without notice and without obligation.
NISSAN INTELLIGENT KEY™
The NISSAN Intelligent Key™ system allows you to lock or unlock your
vehicle, open your trunk and start the engine.
NOTE: It is important to make sure the Intelligent Key is with you (that
is, in your pocket or purse).
The operating range of the door and trunk lock/unlock function is
approximately 31 in (0.8 m).
Locking the vehicle - Push any door handle Request Switch (if so
equipped)
Unlocking the vehicle - Push any door handle Request Switch
(if so equipped)
Push the door handle Request Switch
1 minute; all other doors will unlock.
OPENING THE TRUNK
To open the trunk using the Request Switch (if so equipped),
your Intelligent Key must be with you.
Push the Request/Release Switch (if so equipped)
the trunk handle.
Lift up on the trunk lid to open the trunk.
STARTING THE ENGINE
Depress the brake pedal (CVT) or clutch pedal (MT).
Push the ignition switch to start the engine.
01
once.
once. The corresponding door will unlock.
01
again within
01
02
under
01
02
TURNING THE ENGINE OFF
Shift the shift lever to the P (PARK) position (CVT) or to the
N (NEUTRAL) position (manual transmission) and apply the
parking brake.
Push the ignition switch to turn the engine off.
NISSAN INTELLIGENT KEY™ BATTERY DISCHARGE
If the battery in the Intelligent Key is almost discharged, the
guide light of the Intelligent Key port blinks and the Intelligent
Key insertion indicator is displayed in the vehicle
information display.
To start the engine under these circumstances, insert the
Intelligent Key into the key port in the direction indicated
until it latches into place.
To remove the Intelligent Key from the port, push the ignition
switch to turn the engine off and pull the Intelligent Key out of the port.
The Intelligent Key port does not charge the Intelligent Key battery. If you see the low
battery indicator, replace the battery in the Intelligent Key.
2
AUTOMATIC DOOR LOCKS
All doors lock automatically when the vehicle speed reaches 15 MPH (24 km/h).
All doors unlock automatically when the ignition switch is placed in the OFF position.
The automatic unlock function can be deactivated or activated. To deactivate or activate
the automatic door unlock system, perform the following procedure:
1. Close all doors.
2. Place the ignition switch in the ON position.
3. Within 20 seconds of performing Step 2, push and hold the power door lock switch to the
position (UNLOCK) for more than 5 seconds.
4. When activated, the hazard indicator will flash twice. When deactivated, the hazard indicator
will flash once.
5. The ignition switch must be placed in the OFF and ON position again between each setting
change.
When the automatic door unlock system is deactivated, the doors do not unlock when the ignition
switch is placed in the OFF position. To unlock the door manually, use the inside lock knob or the
power door lock switch (driver’s or front passenger’s side).
WINDSHIELD WIPER/WASHER SWITCH
The ignition switch must be in the ON position to
activate the windshield wipers.
Move the lever to the following positions to operate
the windshield wipers:
1A Intermittent (INT) – Front wipers operate
intermittently and can be further adjusted by
twisting the time control ring 1B.
02 Low Speed (LO) – Continuous low-speed
operation of front wipers.
03 High Speed (HI) – Continuous high-speed
operation of front wipers.
04 Mist (MIST) – Lift the lever up for one sweep
of the front wipers.
Pull the lever toward you to activate front washer fluid and several sweeps of the wipers.
1B04
1A
02
03
HEADLIGHT AND TURN SIGNAL CONTROL
TO ACTIVATE THE AUTOLIGHT SYSTEM
(if so equipped):
Turn the headlight control switch
activate the autolight system. The autolight system can:
Turn the headlights on automatically when it is dark.
Turn the headlights off automatically when it is light.
Keep the headlights on for 45 seconds after you turn the ignition switch to OFF and all doors
are closed.
to the AUTO position to
01
TO DEACTIVATE THE AUTOLIGHT SYSTEM:
Turn the headlight control switch
01
to the OFF,
or
HEADLIGHT CONTROL SWITCH
Turn the headlight control switch
license plate and instrument panel lights.
Turn the headlight control switch
lights remain on.
01
01
to the
to the
position to turn on the front parking, tail,
position to turn on the headlights. All other
FOG LIGHT OPERATION (if so equipped)
NOTE: The headlights must be on and the low beams
Turn the switch (inside collar)
Turn the switch (inside collar)
to the
02
to the OFF position to turn off the fog lights.
02
position to turn on the fog lights.
selected for the fog lights to operate.
HIGH BEAM
Push the headlight control switch forward
the high beam function. The blue
instrument panel will illuminate. Pull the headlight switch
back to the original position to select the low beam. The
blue indicator light will go out.
Pull and release the headlight control switch
the headlight high beams on and off.
indicator light in the
A
B
to select
to flash
0102
position.
A
B
4
STEERING WHEEL SWITCHES FOR AUDIO CONTROL/
BLUETOOTH® (if so equipped)
Press the SOURCE button to turn the radio system on.
To choose AM, FM or XM® stations (if so equipped),
CD/DVD (if so equipped), Music Box™ (if so equipped),
USB/iPod® (if so equipped), Bluetooth® Streaming Audio
(if so equipped) or AUX press SOURCE repeatedly.
The tune up or down
be used to perform the following:
• Tiltthe
(if so equipped) preset station.
• Tiltandholdthe
previous AM, FM or XM® (if so equipped) radio station or category.
• PresstheENTER button to display a list of AM and FM preset stations (vehicles with
navigation).
• Tiltthe
equipped), Music Box™ (if so equipped) or Bluetooth® Streaming Audio (if so equipped),
for less than 1.5 seconds to change tracks.
• Tiltthe
decrease the folder number (if playing compressed audio files).
• Tiltthe
to increase or decrease the title number.
• PresstheENTER button to select an item from the DVD display (vehicles with navigation).
1.5 seconds to increase or decrease the album number or folder.
• PresstheENTER button to display the XM® (if so equipped), CD, USB/iPod® (if so
equipped), Music Box™ (if so equipped), or AUX menu.
Push the + or – control switch to increase or decrease the volume.
*iPod® is a trademark of Apple Inc., registered in the U.S. and other countries.
switch up or down for less than 1.5 seconds to change to an FM/AM or XM®
switch up or down while playing a CD/DVD (if so equipped), USB/iPod® (if so
switch up or down for more than 1.5 seconds while playing a CD to increase or
switch up or down for more than 1.5 seconds while playing a DVD (if so equipped)
switch and ENTER button can
switch up or down for more than 1.5 seconds to seek the next or
switch up or down for more than
switch up or down for more than
CRUISE CONTROL
To activate the cruise control, push the ON/OFF
switch. The CRUISE indicator light in the Vehicle
Information Display will illuminate.
To set cruising speed, accelerate the vehicle to
the desired speed, push the COAST/SET switch
and release. The SET indicator light in the Vehicle
Information Display will illuminate.
5
To reset at a faster cruising speed, push and hold the ACCEL/RES switch. When the vehicle
attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the COAST/SET switch. Release
the switch when the vehicle slows to the desired speed.
To cancel cruise control, push the CANCEL switch or tap the brake pedal. The SET
indicator light in the Vehicle Information Display will go out.
To resume a preset speed, push and release the ACCEL/RES switch. The vehicle
returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).
To turn off cruise control, push the ON/OFF switch. Both the CRUISE indicator light
and the SET indicator light in the Vehicle Information Display will go out.
0204
01
0910070803
05
06
AUTOMATIC CLIMATE CONTROL (if so equipped)
01
AUTO BUTTON
Press the AUTO button
desired temperature. This will allow the fan speed, air flow distribution and temperature
to be automatically maintained.
When AUTO is pressed, AUTO will illuminate. When DUAL
illuminate.
To disable auto mode, press one of the air flow mode control buttons
speed control dial
02
DRIVER’S SIDE TEMPERATURE CONTROL D IAL
Turn the driver’s side temperature control dial left for cold air or right for hot air.
03
DUAL BUTTON
Press the DUAL button to turn the passenger’s side temperature controls on or off. This will
allow the passenger’s side temperature to be adjusted independently from the driver’s side
control.
04
PASSENGER’S SIDE TEMPERATURE CONTROL DIAL
Turn the passenger’s side temperature control dial left for cold air or right for hot air; doing so
will activate dual mode.
01
. Turn the driver’s side temperature control dial 02 to the
06
or press the front defroster control button
03
is pressed, DUAL will
05
, turn the fan
07
.
6
05
AIR FLOW MODE CONTROL BUTTONS
Press the buttons to select the following air flow outlets:
Air flows from the center and side vents.
Air flows from the center, side and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
06
FAN SPEED CONTROL DIAL/OFF BUTTON
Turn the fan speed control dial to the left (slower) or right (faster) to manually control fan
speed. Press OFF to cancel fan speed operation and turn off climate control operation.
07
DEFROSTING/DEMISTING FRONT AND SIDE WINDOWS
Press the defroster control button to turn the system on. The A/C automatically turns
on when the defroster mode is selected.
Turn the driver’s side temperature control dial left or right to set the desired temperature.
To set the defroster on high, turn the fan speed control dial all the way to the right.
08
DEFROSTING REAR WINDOW AND OUTSIDE HEATED MIRRORS (if so equipped)
Push the rear window defroster switch
on. Push the switch again to manually turn the
RR
defroster off. This function automatically turns off in approximately 15 minutes.
09
A/C ON/OFF BUTTON
Press the A/C button to manually turn the A/C on or off.
10
AIR RECIRCULATION BUTTON
Press the air recirculation button to recirculate air inside the vehicle.
Press the air recirculation button again to turn air recirculation off.
The air recirculation mode can only be selected if the air flow control mode is in the
following positions: ,
or
.
7
07
01
02
03
06
04
05
FM/AM/XM®* RADIO WITH CD PLAYER (vehicles with navigation)
01
FM/AM BUTTON
Pressing the FM/AM button will change the band to FM1, FM2 or AM radio stations.
02
XM BUTTON*
Press the XM button to change the band to XM1, XM2 or XM3 satellite radio stations.
03
DISC/AUX BUTTON
Press the DISC/AUX button to play a CD or DVD loaded into the player.
Press the DISC/AUX button again to switch to Music Box™, USB/iPod®, Bluetooth®
Streaming Audio or AUX modes.
NOTE: You may need to adjust the volume on any compatible device plugged into the auxiliary jacks
to find the most desired sound level of the audio system.
AUXILIARY INPUT JACKS
The auxiliary input jacks are located inside the center console under
the armrest. NTSC compatible devices such as video games, some
MP3 players and camcorders can be connected to the auxiliary input
jacks. Before connecting a device to the AUX jacks, turn the portable
device off. With a compatible device connected to the AUX input jacks,
press the DISC/AUX button until the AUX mode appears in the display. The output from the
device will be played through the display and audio system. The front display screen will only
play videos when the vehicle is in the P (PARK) position and the parking brake is engaged.
AUX Jack Color Codes:
The red jack is for right channel audio input.
The white jack is for left channel audio input.
The yellow jack is for video input.
04
SEEKING BUTTON
To scan quickly through each broadcasting station, press the seeking button left or right .
For XM® radio, press or to switch to the first channel of the previous or next category.
Press or to change tracks on a CD.
Press and hold or to fast forward or rewind a track on a CD.
8
05
STATION SELECT BUTTONS
Twelve stations can be set for the FM band, six for the AM band and eighteen for XM®* radio.
To store a station in a preset you must first select a radio band by pressing the FM/AM or
XM button, then tune to the desired AM, FM or XM® station.
Then press and hold the desired station select button (1-6) until the preset number is
updated on the display and the sound is briefly muted. The channel indicator will then
come on and the sound will resume. Programming is now complete.
To retrieve a previously set station, select the radio band where the preset was stored,
then press the corresponding station select button (1-6).
06
TUNE/FOLDER/AUDIO CONTROL KNOB (Bass, Treble, etc.)
To manually tune the radio, turn the TUNE/FOLDER knob right or left. To adjust the Bass,
Treble, Balance and Fade, press the AUDIO knob until the desired mode appears in the
display. Then turn the TUNE/FOLDER knob to adjust to the desired level. Once adjusted
to the desired level, press the AUDIO control knob until the radio or CD display reappears.
While playing an MP3 CD or a compatible device plugged into the USB jack, turn the
TUNE/FOLDER knob right or left to skip forward or backward through available folders.
07
OPEN/TILT BUTTON
The CD/DVD insert slot is located behind the display screen. To insert a CD, DVD or access
the (eject) button, press the OPEN/TILT button on the audio system. The display screen will automatically move down to expose the CD/DVD insert slot. Insert the CD/DVD into the
slot with the label side facing up. The CD/DVD will be guided automatically into the slot and
begin playing. To return the display screen to its upright position after the CD/DVD is inserted,
press the OPEN/TILT button again.
TO EJECT A CD
First press the OPEN/TILT button
07
on the audio system. Then press the button to
eject a loaded CD or DVD.
PLAY MODE
Play mode allows you to change the play pattern of a loaded CD.
While a CD is playing, select the “Menu” key on the display, then select the “Play Mode”
key and a list of various play patterns will be displayed.
*XM® Satellite Radio is only available on vehicles equipped with optional XM® satellite subscription.
USB JACK WITH iPod® CONNECTIVITY (if so equipped)
The USB input jack is located in the center console under the armrest.
To connect a compatible USB device, open the protective cover on the USB jack, and insert the
USB device into the jack. When a compatible storage device is plugged into the jack, compatible
audio or video files on the storage device can be played through the vehicle’s audio system.
Video file playback is only available on vehicles with navigation.
To connect an iPod®, open the USB jack cover, connect the USB end of the cable supplied
with your iPod® to the jack, then connect the other end of the cable to the iPod®. When the
ignition switch is in the ACC or ON position, the battery of your iPod® (if compatible) will
charge while connected to your vehicle.
9
PLAYI NG AN iPod®
The interface for iPod® operation shown on the vehicle center display is similar to the iPod® interface.
Select the USB/iPod® mode using one of the following methods:
Push the SOURCE select switch on the steering wheel.
Press the DISC/AUX button.
FOR USB MEMORY (vehicles with navigation):
After selecting the USB/iPod® mode, select the “Play Movie Contents” key or “Play Audio
Contents” key to start playing audio or video files on the device.
SEEKING BUTTON
Press or for less than 1.5 seconds to skip through tracks.
Press and hold or for more than 1.5 seconds to rewind or fast forward. When the
button is released the audio will play at normal speed.
MUSIC BOXTM HARD DRIVE AUDIO SYSTEM (if so equipped)
The Music Box Hard Drive audio system can store songs from CDs being played. The system has a
9.3 gigabyte (GB) storage capacity and can record up to 200 hours (approximately 2,900 songs).
RECORDING CDS
The system will not record MP3 or WMA files,
only regular formatted CDs.
1. Turn the audio system on and insert a CD.
2. Select the “START REC” key. The system
starts recording and playing the first track
on the CD.
PLAYI NG RECORDED SONGS
Select Music Box™ using one of the following
methods:
Push the SOURCE select switch on the
steering wheel.
Press the DISC/AUX button repeatedly
until the center display changes to Music
Box™ mode.
• Press or for less than 1.5
seconds to skip through tracks.
• Pressandhold or for more than 1.5 seconds to rewind or fast forward. When the
button is released the audio will play at normal speed.
• TurntheTUNE/FOLDER knob right or left to change albums. When playing “All Songs,”
the TUNE/FOLDER knob changes the track instead of the album.
10
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.