Ninja BL773CO Owner's Manual

Download

Page 1

Mega Kitchen System

BL773CO

OWNER’S GUIDE

www.ninjakitchen.com

1-877-646-5288

Page 2

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

WARNING: TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK OR INJURY:

1 WARNING: Remove utensils prior to

processing. Failure to remove may cause the jar to be damaged or to shatter which

READ ALL INSTRUCTIONS BEFORE USING YOUR NINJA® MEGA KITCHEN SYSTEM®.

POLARIZED PLUG

WARNING: To reduce the risk of

electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will ﬁt into a polarized outlet only one way. If the plug does not ﬁt fully into the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician to install the proper outlet. DO NOT modify the plug in

any way.

WARNING: Extension cords are

not recommended for use with this product.

may cause personal injury.

2 WARNING: Stacked Blade Assembly is

sharp, not locked in place and removable, handle with care. When handling the Stacked Blade Assembly, always hold it by the shaft. Failure to do so will result in a risk of laceration.

3 WARNING: Stacked Blade Assembly is

sharp and not locked in place. If using the pour spout, ensure the lid is fully locked onto the pitcher. If pouring with the lid removed, carefully remove the Stacked Blade Assembly ﬁrst, holding it by the shaft. Failure to do so will result in a risk of laceration.

4 WARNING: Chopping Blade Assembly is

sharp and not locked in place. Before emptying contents carefully remove lid and Chopping Blade Assembly, holding it by the shaft. Failure to do so will result in a risk of laceration.

THIS BOOK COVERS MODEL NUMBERS:

BL773CO 30

TECHNICAL SPECIFICATIONS

Voltage: 120V., 60Hz. Power: 1500 Watts

Pitcher Capacity: 72 oz. (9 cups, 2.15 L) MAX Liquid Capacity: 64 oz. (8 cups, 1.9 L)

Bowl Capacity: 64 oz. (8 cups, 1.8 L)

Nutri Ninja® Cup Capacity: 16 oz. (2 cups, 470ml)

5 CAUTION: Do not blend hot liquids, doing

so may cause excessive pressure build-up, resulting in risk of the user being burned.

6 CAUTION: We do not recommend

grinding in any of our Nutri Ninja

7 CAUTION: Remove the Nutri Ninja Blade

Assembly from the cup upon completion of blending. Some ingredients have the potential to expand after blending resulting in excessive pressure buildup that can pose a risk of injury.

cups.

1-877-646-5288

Page 3

8 To protect against electrical shock, do not

submerge the appliance or allow the power cord to come into contact with water or any other liquid.

9 DO NOT allow the appliance to be used by

children. Close attention is necessary when used near children. This is not a toy.

10 Never leave an appliance unattended when

inuse.

11 Appliance accessories are not intended to be

used in the microwave as it may result in damage to the accessories.

12 Turn the appliance Off and remove the power

cord from the electrical outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the electrical outlet. Never pull from the power cord.

13 DO NOT abuse the power cord. Never carry

the appliance by the power cord or yank it to disconnect from electrical outlet; instead grasp the plug and pull to disconnect.

14 DO NOT operate any appliance with a damaged

cord or plug, or after the appliance malfunctions, has been dropped or damaged in any manner. This appliance has no serviceable parts. Return the appliance to SharkNinja Operating LLC for examination, repair or adjustment.

15 DO NOT let the power cord hang over the edge of

table or counter or touch hot surfaces such as the

stove. 16 Always use appliance on a dry, level surface. 17 Keep hands, hair, clothing, as well as utensils

out of container while processing to reduce the

risk of severe injury to persons or damage to the

appliance. A scraper may be used but only when

the appliance is not running. 18 Avoid contact with moving parts. 19 DO NOT attempt to sharpen blades. 20 DO NOT use the appliance if blade assemblies

are bent or damaged.

21 To reduce risk of injury, never place the blade

assemblies on the base without the pitcher or Nutri Ninja® cup properly attached.

22 DO NOT operate this appliance on or near any

hot surfaces (such as gas or electric burner or in a heated oven).

23 The use of attachments or accessories

including canning jars, not recommended by the manufacturer may result in ﬁre, electric shock or personal injury.

24 DO NOT remove the container from the motor

base while the appliance is in operation.

25 To reduce the risk of injury, NEVER operate the

appliance without the lid in place; DO NOT try to defeat the interlock mechanism; make sure that the attachment is properly installed before operating the appliance.

26 DO NOT expose containers to extreme

temperature changes. 27 DO NOT overﬁll. 28 Never feed food by hand when using the food

processor. Always use the food pusher. 29 DO NOT operate the appliance empty. 30 If the appliance overheats, a thermal switch will

become activated and shut off the motor. To

reset, unplug the appliance and let it cool down

for approximately 15 minutes before using again. 31 THIS PRODUCT IS INTENDED FOR

HOUSEHOLD USE ONLY. Do not use this

appliance for anything other than its intended

use. Do not use outdoors. 32 The maximum rating is based on the Stacked

Blade Assembly (pitcher) that drives the greatest

power and other recommended attachments may

draw signiﬁcantly less power or current.

SAVE THESE

INSTRUCTIONS

www.ninjakitchen.com

Page 4

Contents

Thank you for purchasing the Ninja® Mega Kitchen System®.

Getting to Know Your Ninja® Mega Kitchen System® ............................................................3

Before First Use ...............................................................................................................4

Assembly and Use for the Blender Pitcher ..........................................................................5

Assembly and Use for the Nutri Ninja® Cup .........................................................................7

Assembly and Use for the 64 oz. Bowl ................................................................................8

Assembly and Use for the Cutting Discs ...........................................................................10

Speed Setting & Uses ......................................................................................................11

Care & Maintenance .......................................................................................................12

Troubleshooting Guide .....................................................................................................13

Replacement Parts ..........................................................................................................13

Warranty & Registration ...................................................................................................14

Getting To Know Your Ninja® Mega Kitchen System

Nutri Ninja®

Cup (x3)

To-Go Lid

(x3)

Nutri Ninja®

Blade Assembly

Grating

Disc

Food Processor Bowl

NOTE: Blade assemblies are not interchangeable. NOTE: All containers, lids, discs and blade assemblies are dishwasher safe. Place the lids, discs and blade assemblies on

the top rack only. All containers, lids and plastic components of blade assemblies and disc are BPA free.

Dough Blade

Assembly

1-877-646-5288

Chopping Blade

Pitcher Lid72 oz. Pitcher

Assembly

Spindle

for Discs

Assembly (Pitcher)

Feed Chute Lid with

Two Part Pusher

Reversible Slicing/

Shredding Disc

Motor BaseStacked Blade

Page 5

Before First Use

PLEASE KEEP THESE IMPORTANT SAFEGUARDS IN MIND WHEN USING THE APPLIANCE:

IMPORTANT: Make sure that the motor

base is plugged in for use.

IMPORTANT: Never add ingredients into

the container before placing the Blade Assembly in ﬁrst.

IMPORTANT: Blade Assemblies are not

interchangeable.

IMPORTANT: DO NOT attempt to operate

the appliance without the lid on.

IMPORTANT: Never run the appliance

empty.

IMPORTANT: Appliance accessories are

not intended to be used in the microwave as it may result in damage to the accessories.

WARNING: Stacked Blade Assembly is sharp and not locked in place. If using the pour spout, ensure the lid is fully locked onto the blender pitcher. Failure to do so will result in a risk of laceration.

WARNING: Stacked Blade Assembly is sharp and not locked in place. If pouring with the lid removed, carefully remove the Stacked Blade Assembly ﬁrst, holding it by the shaft. Failure to do so will result in a risk of laceration.

WARNING: Chopping Blade Assembly is sharp and not locked in place. Before emptying contents carefully remove lid and Chopping Blade Assembly, holding it by the shaft. Failure to do so will result in a risk of laceration.

CAUTION: Do not immerse the motor base into

water or any other liquid.

1 Remove all packaging material and labels from the

appliance. Separate/remove all parts from each other.

2 Wash the lids, pitcher, bowl, Nutri Ninja® cups, grating

disc, slicing/shredding disc and blade assemblies in warm, soapy water. When washing the blade assemblies, use a dish-washing utensil with a handle to avoid direct hand contact with blades.

WARNING: Handle the Blade Assemblies and the

grating, slicing/shredding discs with care when washing, as the blades are sharp.

3 Handle blade assemblies with care to avoid contact

with sharp edges. Rinse and air dry thoroughly.

4 The pitcher, bowl, Nutri Ninja cups, lids, grating,

slicing/shredding discs and Blade Assemblies are all dishwasher safe. It is recommended that the lids, grating, slicing/shredding discs and Blade Assemblies be placed on the top rack. Ensure that the Blade Assemblies and the discs are removed from the containers before placing in the dishwasher.

5 Wipe the motor base clean with a damp cloth.

www.ninjakitchen.com

Page 6

Assembly and Use for the Blender Pitcher

WARNING: Handle the Stacked Blade Assembly with care, as the blades are sharp. WARNING: Remove utensils prior to processing. Failure to remove may cause the pitcher to be damaged or

to shatter, which may cause personal injury. WARNING: Never leave the appliance unattended while in use. CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the

user being burned.

IMPORTANT: Make sure that the motor base is plugged in for use.

ASSEMBLY

Fig. 3a

Fig. 2

It’s best to add the liquid ingredients ﬁrst and then the dry ingredients.

1 Review warning and caution statements above before

proceeding to number 2.

2 Place the motor base on a clean, dry, level surface

such as a counter or table top.

3 Align and lower the Pitcher onto the motor base.

(Fig. 1) Handle should be aligned slightly to the right of

the “LOCK” symbol on the motor base.

4 Rotate the blender pitcher clockwise until it clicks in

place. As the pitcher rotates, it will lower and the safety

tabs on the bottom of the pitcher will slide under the

safety tabs on the top of the motor base. (Fig. 2)

5 The pitcher can be placed on the motor base two ways;

the handle can be on the front right corner or the front

left corner. (Fig. 3a, Fig. 3b)

6 Holding the Stacked Blade Assembly by the top of the

shaft, place it onto the drive gear inside the pitcher.

Ensure that the Stacked Blade Assembly is seated

properly and is standing upright. (Fig. 4)

NOTE: The Stacked Blade Assembly will ﬁt loosely on

the drive gear.

1-877-646-5288

Fig. 3bFig. 1 Fig. 4 Fig. 5

7 Add the ingredients to the pitcher, making sure that

they do not exceed the highest measured marking line on the side of the pitcher.

NOTE: If you need to add additional ingredients while

the appliance is processing, open the pour spout cap and pour the ingredients in through the opening.

NOTE: When blending any kind of liquids, such as

mixtures of any drinks or smoothies, do not exceed the “Max liquid” mark (64 ounces) on the pitcher.

8 Plug the power cord into the electrical outlet and press

the power button ( ).

IMPORTANT: As a safety feature, the power

button ( ) will ﬂash and the motor will not work if the pitcher and lid are not installed correctly. When the pitcher and lid are installed properly, the power button ( ) will be solid, indicating that the appliance is ready for use.

9 Holding the lid by the handle in the upright position,

place it on top of the pitcher aligning the arrow ( ) located on the lid with the arrow ( ) located on the pitcher’s handle. (Fig. 5) Press the handle down until you hear a click.

Page 7

USE

REMOVAL

Fig. 6 Fig. 8

10 Select the speed that best suits your needs. (Fig. 6)

NOTE: Pulse ingredients for even chopping by pressing

down in short intervals.

11 When you have reached your desired consistency, stop

the appliance by pressing the power button ( ) and

wait for the blade assembly to stop turning. (Fig. 7)

12 To remove the lid, press the release button on the lid,

pull the lid handle up to a 90° angle and lift the lid off.

Turn the pitcher counter clockwise and then lift off the

base. (Fig. 7, Fig. 8)

WARNING: Never insert your hands in the pitcher

as the Stacked Blade Assembly is sharp. Always

use a spatula to dislodge food that has stuck to

the sides of the pitcher.

Fig. 7

13 Open the pour spout cap and use the spout to empty

liquid contents.

14 For thicker consistencies, ﬁrst remove the lid by

pressing the release button and pulling the lid handle up to a 90 degree angle to lift lid off the pitcher. Then, carefully remove the Stacked Blade Assembly by the top of the shaft. Place Stacked Blade Assembly away from the work area to avoid accidental contact. Finally, empty contents from the pitcher.

15 Make sure that the unit is unplugged when not in use.

16 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor base and gently pull the unit up and towards you. (Fig. 9)

Fig. 9

www.ninjakitchen.com

Page 8

Assembly and Use for the Nutri Ninja® Cup

WARNING: Handle the Nutri Ninja Blade Assembly with care, as the blades are sharp. WARNING: Remove utensils prior to processing. Failure to remove may cause the Nutri Ninja cup to be

damaged or to shatter, which may cause personal injury. WARNING: Never leave the appliance unattended while in use. CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the

user being burned.

CAUTION: Remove the Nutri Ninja Blade Assembly from the cup upon completion of blending. Some

ingredients have the potential to expand after blending resulting in excessive pressure buildup that can pose

a risk of injury.

IMPORTANT: Make sure that the motor base is plugged in for use.

ASSEMBLY USE REMOVAL

Fig. 2Fig. 1

For best results, use short “PULSES”... Practice makes perfect!!

1 Review warning and caution statements above before

proceeding to number 2.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top.

3 Add ingredients to the Nutri Ninja® cup.

4 Place the Nutri Ninja Blade Assembly onto the cup and

screw it tightly until you have a good seal. (F ig. 1)

5 Turn the Nutri Ninja® cup upside down and place it

onto the motor base, aligning the tabs on the cup with

the motor base. Turn the Nutri Ninja® cup clockwise to

lock into place. You will hear a click when the lock is

engaged. (Fig. 2) Turn the power button on, the single

serve button will illuminate.

6 Press down on the Single Serve button in short

intervals to activate. (Fig. 3)

7 Once you have reached your desired consistency,

turn the power button off. Turn the Nutri Ninja® cup

counter-clockwise and pull straight up to remove.

(Fig. 4, Fig. 5)

1-877-646-5288

Fig. 3 Fig. 4 Fig. 5

NOTE: Do not overﬁll! To avoid spilling, do not add

ingredients past the “Max” ﬁll line.

8 Turn the cup upright and remove the Nutri Ninja Blade

Assembly by twisting the blade assembly counterclockwise.

9 Place the To-Go drinking lid onto the Nutri Ninja® cup,

twist to seal and enjoy!

10 Make sure that the motor base is unplugged when not

in use.

11 To release the motor base

from the counter or table top, place your hands underneath both sides of the motor base and gently pull the unit up and towards you. (Fig. 6)

NOTE: To order additional Nutri Ninja® Cups, please

visit our website: www.ninjakitchen.com or feel free to contact customer service: 1-877-646-5288.

Fig. 6

Page 9

Assembly and Use for the Food Processor Bowl

WARNING: Chopping Blade Assembly is sharp and not locked in place. Before emptying contents carefully

remove lid and Chopping Blade Assembly, holding it by the shaft. Failure to do so will result in a risk of

laceration. WARNING: Remove utensils prior to processing. Failure to remove may cause the bowl to be damaged or to

shatter, which may cause personal injury. WARNING: Never leave the appliance unattended while in use. CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the

user being burned.

CAUTION: Remove the lid from the bowl upon completion of processing. Some ingredients have the potential

to expand after blending resulting in excessive pressure buildup that can pose a risk of injury.

IMPORTANT: Make sure that the motor base is plugged in for use.

ASSEMBLY

Fig. 3a

1 Review warning and caution statements above before

proceeding to number 2.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top.

3 Align and lower the Bowl onto the motor base. (Fig. 1)

Handle should be aligned slightly to the right of the

“LOCK” symbol on the motor base.

4 Rotate the bowl clockwise to lock into place. You will

hear a click when the lock is engaged. (Fig. 2)

5 The bowl can be placed on the motor base two ways;

the handle can be on the front right corner or the front

left corner. (Fig. 3a, Fig. 3b)

6 Holding the desired Blade Assembly by the top of the

shaft, place it onto the drive gear inside the bowl.

Ensure that the Blade Assembly is seated properly and

is standing upright. (Fig. 4)

NOTE: The Blade Assembly will ﬁt loosely on the drive

gear.

7 Add the ingredients to the bowl, making sure that they

do not exceed the highest measured marking line on

the side of the bowl.

Fig. 3bFig. 2

8 Holding the lid by the handle in the upright position,

place it on top of the bowl aligning the arrow ( ) located on the lid with the arrow ( ) located on the bowl’s handle. (Fig. 5) Press the handle down until you hear a click.

NOTE: The 64 oz. bowl is not intended for

blending drinks. Do not overﬁll.

NOTE: To add liquids during processing,

open the drizzle hole on the top of the lid and pour the liquid slowly into the mixture.

9 Plug the power cord into the electrical

outlet and press the power button ( ).

IMPORTANT: As a safety feature, the power

button ( ) will ﬂash and the motor will not work if the bowl and lid are not installed correctly. When the bowl and lid are installed properly, the power but ton ( ) will be solid, indicating that the appliance is ready for use.

Fig. 4 Fig. 5Fig. 1

www.ninjakitchen.com

Page 10

Assembly and Use for the Food Processor Bowl - cont.

USE

REMOVAL

CHOPPING BLADE

ASSEMBLY

USE

DOUGH BLADE

ASSEMBLY

Fig. 1 Fig. 2 Fig. 3 Fig. 4

USING THE CHOPPING BLADE ASSEMBLY

1 Review warning and caution statements at the top of

page 8 before proceeding to number 2.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top.

3 Secure the bowl onto the motor base.

4 Holding the Chopping Blade Assembly by the shaft,

place it onto the gear shaft inside the bowl. Ensure that

the Chopping Blade Assembly ﬁts around the gear shaft

and that it is standing straight. (Fig. 1)

5 Add the ingredients and secure the bowl lid onto the

bowl. (Fig. 1)

6 Plug the power cord into the electrical outlet and press

on the power button ( ). (Fig. 2) Select the speed

that best suits your needs. Pulse ingredients for even

chopping by pressing down in short intervals.

NOTE: Please refer to “Speed Settings & Uses” chart

for suggested uses and speeds.

7 When you have reached your desired consistency, stop

the appliance by pressing the power button ( ) and

wait for the Chopping Blade Assembly to stop turning.

8 To remove the lid, press the release button on the lid

and pull the lid handle up to a 90° angle. (Fig. 2)

9 Turn the bowl counter-clockwise and lift it to remove it

from the motor base. (Fig. 3)

10 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor

base and gently pull the unit up and towards you.

(Fig. 4)

1-877-646-5288

Fig. 5

USING THE DOUGH BLADE ASSEMBLY

IMPORTANT: Use only the “DOUGH” but ton when

using this attachment.

1 Review warning and caution statements at the top of

page 8 before proceeding to number 2.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top.

3 Secure the bowl onto the motor base.

4 Holding the Dough Blade Assembly by the shaft, place

it onto the gear shaft inside the bowl. Ensure that the Dough Blade Assembly ﬁts around the gear shaft and that it is standing straight. (Fig. 5)

5 Add the ingredients and secure the bowl lid onto the

bowl. (Fig. 5)

NOTE: For best results add wet ingredients ﬁrst and

then add dry ingredients.

6 Plug the power cord into the electrical outlet and press

on the power button ( ). (Fig. 2)

7 To remove the lid, press the release button on the lid

and pull the lid handle up to a 90° angle. (Fig. 2)

8 Turn the bowl counter-clockwise and lift it to remove it

from the motor base. (Fig. 3)

9 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor base and gently pull the unit up and towards you. (Fig. 4)

Page 11

Assembly and Use of the Cutting Discs

WARNING: The Cutting Discs are sharp. Always use the ﬁnger holes when placing or removing the cut ting

discs. Failure to do so will result in a risk of laceration. WARNING: Remove utensils prior to processing. Failure to remove may cause the bowl to be damaged or to

shatter, which may cause personal injury. WARNING: Never leave the appliance unattended while in use.

IMPORTANT: Make sure that the motor base is plugged in for use.

NOTE: The feed chute lid features a two part pusher to guide food

through the chute. Use the full pusher for larger items such as cucumbers. Twist and pull to remove the smaller pusher and use the narrow chute for smaller items such as carrots.

IMPORTANT: Only use Speed 1 DOUGH/DISC when using either

cutting disc attachment.

NOTE: The Slicing/Shredding Disc is reversible. Use the side labeled

“Slicer” for Slicing. Carefully ﬂip the disc over to the side labeled “Shredder” for shredding.

1 Review warning statements at the top before proceeding to number 2.

2 Place the motor base on a clean, dry, level surface such as a counter

or table top. (Fig. 6)

3 Secure the bowl onto the motor base.

4 Place the spindle inside the bowl.

5 Use the ﬁnger holes to grasp the selected disc and place it over the

spindle.

6 Place the feed chute lid on the bowl and turn clockwise until you here a click

indicating the lid is locked in place. (Fig. 6)

7 Plug the power cord into the electrical outlet and press the power

button ( ) to turn the unit “On”.

8 Select Speed 1 DOUGH/DISC on the control panel. The disc will

begin spinning.

9 Add the food that you want to slice, shred or grate through the feed

chute on the lid. (Fig. 6) Use the two-part food pusher to help guide the food through the feed chute. The middle piece of the food pusher is removable to use for smaller ingredients.

10 When ﬁnished, stop the appliance by pressing the power button ( )

and wait for the disc to stop turning. Press the button on the feed chute lid located near the handle to unlock and turn the lid counter-clockwise. Lift to remove from the processor bowl. Using the ﬁnger holes, carefully lift the cutting disc out of the bowl and remove the spindle.

11 To release the motor base from the counter or

table top, lift the base up from underneath the sides of the unit. Release paddles on both sides will help to disengage the suction feet from the surface.

Fig. 6

www.ninjakitchen.com

Page 12

Speed Setting & Uses

TIP: Be sure to add seeds or protein powder after you’ve added your liquids and before adding your ice for optimal breakdown.

FUNCTION CONTAINER BLADE ASSEMBLY SPEED BUTTON TYPE OF FOOD

Ultra Smooth Nutrient Extractions*

Small Batch

Blending

Small Batch Chopping Nutri Ninja Cup Nutri Ninja Blade Assembly

Dough Making Bowl Dough Blade Assembly 1

Batters Bowl Chopping Blade Assembly

Dressings and Sauces Bowl Chopping Blade Assembly 2

Purees and Dips Bowl

Grating Bowl Grating Disc 1

Large Batch Chopping/

Grinding

Slicing/Shredding Bowl Slicing/Shredding Disc 1

Eggs Pitcher Stacked Blade Assembly 1

Nut Butters Pitcher Stacked Blade Assembly 2

Soups and Sauces** Pitcher Stacked Blade Assembly 2

Large Batch Drink

Making

Nutri Ninja® Cup Nutri Ninja Blade Assembly Nutri Ninja - Hold Down

Nutri Ninja® - Pulse

Short Intervals

Chopping Blade Assembly

Bowl Chopping Blade Assembly PULSE

Pitcher Stacked Blade Assembly 3

PULSE

Smoothies/Protein Shakes

Smooth Purees

Sauces**

Soups**

Chopped Nuts

Bread Dough

Pie Dough

Pizza Dough Pretzel Dough Cookie Dough

Pasta Dough

Cakes

Mufﬁns

Pancake Batter

Cheesecake

Brownies

Vinaigrettes

Aiolis

Marinades

Sauces**

Pesto

Hummus

Vegetable Purees

Fruit Purees

Cream Cheese Dips

Grated cheese Bread crumbs

Salsa

Vegetables

Nuts

Chopped Salads

Burgers

Meatballs

Taco Meat

Vegetables

Cheese

Omelets

Scrambled Eggs

Stratas

Frittatas

Almond Butter

Peanut Butter

Tomato Soup**

Tomato Sauce**

Root Vegetable Soup**

Smoothies/Protein Shakes

Frozen Cocktails

Milkshakes

Frappes

* Extract a Drink Containing Vitamins & Nutrients From Fruits & Veggies.

** When blending soups or sauces, make sure they’re cooled to room temperature ﬁrst - Ninja® containers are not intended for

hot blending.

1-877-646-5288

Page 13

Care & Maintenance

HOW TO CLEAN

CAUTION: Make sure that the motor base is

unplugged from the power source before inserting or removing any attachment and before cleaning.

CAUTION: DO NOT immerse the motor base into

water or any other liquid.

1 Separate/remove all parts from each other.

2 Hand Washing: Wash the lids, pitcher, bowl, Nutri

Ninja® cup, cutting discs and blade assemblies in warm, soapy water. When washing the blade assemblies and cutting discs, use a dish-washing utensil with a handle to avoid direct hand contact with blades. Handle blade assemblies and cutting discs with care to avoid contact with sharp edges. Rinse and air dry thoroughly.

Dishwasher: The containers, lids, blade assemblies,

cutting discs and attachments are all dishwasher safe. The lids, cutting discs and blade assemblies are top rack dishwasher safe. Ensure that the blade assemblies and cutting discs are removed from the containers before placing in the dishwasher.

WARNING: Handle the Stacked Blade Assembly,

Chopping Blade Assembly, Nutri Ninja Blade Assembly, Grating Disc and Slicing/Shredding Disc with care when washing, as the blades are sharp. Contact with the blades’ edges can result in laceration.

3 Wipe the motor base clean with a damp cloth

Please call customer service if any servicing needs to

be performed on the appliance at 1-877-646-5288.

HOW TO STORE

1 Store the Ninja® Mega Kitchen System® upright with

the blade assembly inside the corresponding container with the lid secured on top. Do not place anything on top. Store the rest of the attachments in a safe place where they will not be damaged and won’t cause harm. Loosely wrap the power cord around the motor base.

RESETTING THE MOTOR THERMOSTAT

The Ninja Mega Kitchen System features a unique safety system which prevents damage to the unit’s motor and drive system should you inadvertently overload your appliance. If the appliance is being overloaded, the motor will stop. To reset the appliance, follow the resetting procedure below:

1 Unplug the appliance from the electrical outlet.

2 Remove and empty the container and ensure that no

food is jamming the blade assembly.

3 Allow the appliance to cool for approximately 15

minutes.

4 Re-install the container onto the base and re-plug the

appliance into the electrical outlet.

5 Proceed to use the appliance as before making sure not

to exceed the recommended maximum capacities.

www.ninjakitchen.com

Page 14

Troubleshooting Guide

PROBLEMS POSSIBLE REASONS & SOLUTIONS

Motor doesn’t start or blade assembly doesn’t rotate.

Make sure the container is securely placed on motor base.

Make sure the lid is securely on container in the correct position (align arrows).

The appliance is turned “Off”. Press the power button ( ) to turn “On”.

Check that the plug is securely inserted into the electrical outlet.

Check the fuse or circuit breaker.

The unit has overloaded or overheated. Unplug and wait approximately 15 minutes before using again.

Food is unevenly chopped.

Food is chopped too ﬁne or is too watery.

Food collects on lid or on the sides of the container.

You cannot achieve snow from solid ice.

Motor base won’t stick to counter or table top.

Leaking is occurring when using the Nutri Ninja® cup.

Ingredients are stuck and not fully blending.

The Nutri Ninja button does not work.

Either you are chopping too much food at one time, or the pieces are not of an even size. Try processing smaller amounts per batch.

The food has been over processed. Use pulse button for controlled processing.

The mixture is to thick. Add more liquid.

Do not use ice that has been sitting out or has started to melt. Use ice straight from the freezer.

Make sure surface and suction feet are wiped clean. Suction feet will only stick to smooth surfaces. Suction feet WILL NOT stick on some surfaces such as, wood, tile and non-polished ﬁnishes.

DO NOT attempt to use appliance when the motor base is stuck to a surface that is not secure, (cutting board, platter, plates, etc.).

Ensure the blade is properly twisted into the cup and sealed tightly into place. Check to see that the lid gasket is properly in place.

Do not overﬁll the cup. Never add ingredients past the “Max” ﬁll line.

You may have overloaded the Nutri Ninja® cup. Try pulsing 3-5 times and then resume blending. You may also add liquid to make blending easier.

The Nutri Ninja button will only operate when you have the Nutri Ninja cup assembled to the motor base. This function was designed speciﬁcally for the Nutri Ninja Cups to operate at the ideal speed.

Replacement Parts

ORDERING REPLACEMENT PARTS

To order additional parts and attachments, please visit our website: www.ninjakitchen.com or feel free to contact customer service: 1-877-646-5288.

1-877-646-5288

Page 15

ONE (1) YEAR LIMITED WARRANTY

SharkNinja Operating LLC warrants this product to be free from material defects and workmanship for a period of one (1)

year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and exceptions.

The liability of SharkNinja Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been performed by a repair person not authorized by SharkNinja Operating LLC.

If your appliance fails to operate properly while in use under normal household conditions within the Limited Warranty period, you may return the complete appliance and accessories with proof of purchase and date, freight prepaid. For Customer Service support, call 1-877-646-5288 or visit our website www.ninjakitchen.com.

If the appliance is found by SharkNinja Operating LLC to be defective, in SharkNinja Operating LLC’s sole discretion, we will repair or replace it free of charge. Proof of purchase date and a check made payable to SharkNinja Operating LLC in the amount of $19.95 to cover the cost of return shipping and handling must be included.*

This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional warranties. The responsibility of SharkNinja Operating LLC if any, is limited to the speciﬁc obligations expressly assumed by it under the terms of this Limited Warranty. In no event is SharkNinja Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

This Limited Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state or from province to province.

*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and

to attach tag to item before packing with your name, complete address and phone number with a note giving

purchase information, model number and what you believe is the problem with the item. We recommend you insure

the package (as damage in shipping is not covered by your Limited Warranty). Mark the outside of your package

“ATTENTION CUSTOMER SERVICE”.

PRODUCT REGISTRATION

Please visit www.ninjakitchen.com or call 1-877-646-5288 to register your new Ninja® product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.

The registration will enable us to contact you in the unlikely event of a product safety notiﬁcation. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.

www.ninjakitchen.com

Page 16

SharkNinja Operating LLC US: Newton, MA 02459 CAN: Ville St-Laurent, QC H4S 1A7

1-877-646-5288 www.ninjakitchen.com

Mega Kitchen System, Ninja, and Nutri Ninja are registered trademarks of SharkNinja

Operating LLC.

Illustrations may differ from actual product. We are constantly striving to improve our products, therefore the speciﬁcations contained herein are subject to change without notice.

For SharkNinja U.S. Patent information visit www.sharkninja.com/USPatents.