Nilfisk-Advance 56315000, 24D-C, 56315001, 26D, 56315002 Service Manual

...

0 (0)

Convertamatic™ 24, 26, 28, 32

BA 625, 725, 825

Service Manual

Advance Models: 56315000(24D-C), 56315001(26D), 56315002(28D), 56315003(24C-C), 56315004(28D-C), 56315005(28C-C), 56315006(X24D-C), 56315007(X24C-C), 56315008(26D-C), 56315009(X26D-C), 56315010(26C-C), 56315011(X26C-C), 56315012(X28D-C), 56315013(X28C-C), 56315804(32D-C) 56315805(X32D-C) Nilﬁ sk Models: 56315800(625), 56315801(725), 56315802(725C), 56315803(825)

2/05 revised 4/08 FORM NO. 56043098

TABLE OF CONTENTS

INTRODUCTION .......................................................................................................................................................................................... 2

CAUTIONS AND WARNINGS ...................................................................................................................................................................... 3

SPECIFICATIONS & MAINTENANCE.......................................................................................................................................................4-6

PM CHECKLIST ........................................................................................................................................................................................... 7

KNOW YOUR MACHINE ......................................................................................................................................................................... 8-12

SOLUTION SYSTEM .............................................................................................................................................................................13-19

FUNCTIONAL OVERVIEW ....................................................................................................................................................................... 13

CIRCUIT OVERVIEW SOLUTION AUTO MODE ..................................................................................................................................... 14

SOLUTION SYSTEM MAINTENANCE .................................................................................................................................................... 15

TROUBLESHOOTING GUIDE ............................................................................................................................................................16-17

SOLUTION SOLENOID VALVE REMOVAL .............................................................................................................................................. 18

SOLUTION VALVE DISASSEMBLY AND CLEANING..............................................................................................................................18

SOLUTION FILTER AND BALL VALVE REMOVAL .................................................................................................................................. 19

SOLUTION PUMP REMOVAL .................................................................................................................................................................. 19

SCRUB SYSTEM .................................................................................................................................................................................. 20-27

GENERAL BRUSH SYSTEM FUNCTIONAL OVERVIEW ....................................................................................................................... 20

SPECIAL SCRUB SYSTEM FUNCTIONS ..........................................................................................................................................20-21

SCRUB BRUSH DECK REMOVAL (DISC) ......................................................................................................................................... 22-23

SCRUB BRUSH LIFT ACTUATOR REMOVAL (DISC) ........................................................................................................................ 22-23

SCRUB BRUSH MOTOR/GEARBOX REMOVAL (DISC) ................................................................................................................... 22-23

SCRUB BRUSH DECK LEVELING ............................................................................................................................................................ 24

SCRUB BRUSH DECK REMOVAL (CYLINDRICAL) .......................................................................................................................... 26-27

SCRUB BRUSH MOTOR(S) REMOVAL (CYLINDRICAL) ..................................................................................................................26-27

SCRUB BRUSH BELT REPLACEMENT (CYLINDRICAL) ..................................................................................................................26-27

SCRUB BRUSH SYSTEM MAINTENANCE (CYLINDRICAL).................................................................................................................. 26

SCRUB BRUSH REMOVAL AND INSTALLATION (CYLINDRICAL) ........................................................................................................ 26

SCRUB BRUSH LIFT ACTUATOR REMOVAL (CYLINDRICAL) ......................................................................................................... 26-27

RECOVERY SYSTEM ........................................................................................................................................................................... 28-34

FUNCTIONAL OVERVIEW ....................................................................................................................................................................... 28

VACUUM MOTOR CONTROL CIRCUIT OVERVIEW (AUTO MODE) ..................................................................................................... 29

VACUUM/RECOVERY SYSTEM MAINTENANCE CHECKLIST ............................................................................................................. 30

MAINTENANCE OF RECOVERY TANK FLOAT SWITCHES .................................................................................................................. 31

MAINTENANCE OF VACUUM MOTOR INLET SCREEN ........................................................................................................................32

VACUUM MOTOR REMOVAL .................................................................................................................................................................. 33

RECOVERY TANK REMOVAL ................................................................................................................................................................. 34

SQUEEGEE SYSTEM ........................................................................................................................................................................... 35-38

SQUEEGEE LIFT LINKAGE ADJUSTMENT ............................................................................................................................................ 35

SERVICING THE SQUEEGEE ................................................................................................................................................................. 36

ADJUSTING THE SQUEEGEE ................................................................................................................................................................ 36

SQUEEGEE MOUNT ASSEMBLY REMOVAL ......................................................................................................................................... 37

CASTER WHEEL REMOVAL ................................................................................................................................................................... 38

WHEEL DRIVE SYSTEM ......................................................................................................................................................................39-47

GENERAL FUNCTIONAL OVERVIEW ................................................................................................................................................39-41

WHEEL DRIVE TROUBLESHOOTING GUIDE ........................................................................................................................................ 42

DRIVE MOTOR TRANSAXLE REMOVAL ........................................................................................................................................... 43-44

DRIVE WHEEL REMOVAL ....................................................................................................................................................................... 45

(5K) POTENTIOMETER (R1) TESTING AND REMOVAL ........................................................................................................................ 46

(5K) POTENTIOMETER (R1) INSTALLATION AND ADJUSTMENT ................................................................................................... 46-47

(100K) POTENTIOMETER (R2) TESTING AND REMOVAL .................................................................................................................... 47

ELECTRICAL SYSTEM ......................................................................................................................................................................... 48-75

BATTERIES .............................................................................................................................................................................................. 48

DESCRIPTION OF

DESCRIPTION OF THE BATTERY CONDITION INDICATORS .............................................................................................................. 49

BATTERY CHARGING, MAINTENANCE AND TESTING ...................................................................................................................50-51

ACTUATOR DRIVE NUT ADJUSTMENT ............................................................................................................................................52-53

CURTIS CONTROLLER ...................................................................................................................................................................... 54-57

FUNCTIONAL OVERVIEW OF MAIN CONTROL BOARD ...................................................................................................................... 58

MAIN CONTROLLER ERROR CODES ................................................................................................................................................... 59

MAIN CONTROLLER DIAGNOSTIC SERVICE TEST MODE ............................................................................................................ 60-64

MAIN CONTROL PROGRAMING OPTIONS ...................................................................................................................................... 65-70

ELECTRICAL COMPONENT LOCATION ................................................................................................................................................ 71

WIRING DIAGRAM ................................................................................................................................................................................... 72

WIRING SCHEMATIC............................................................................................................................................................................... 73

APPENDIX ............................................................................................................................................................................................. 74-76

DETERGENT (AXP / EDS) SYSTEM PLUMBING SCHEMATIC ............................................................................................................. 74

EXTENDED SCRUB SYSTEM PLUMBING SCHEMATIC ....................................................................................................................... 75

DETERGENT (AXP / EDS) SYSTEM PREPARATION AND USE ............................................................................................................ 76

Note: All references to right, left, front, or rear in this manual are as seen from the operator’s stand-point.

THE LOW VOLTAGE CUTOUT FEATURE ............................................................................................................... 49

revised 5/07

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 1

INTRODUCTION

This manual will help you get the most from your Nilﬁ sk-Advance scrubber. Read it thoroughly before servicing the machine. Note: Bold numbers and letters in parentheses indicate an item illustrated on pages 8-10.

PARTS AND SERVICE

Repairs, when required, should be performed by your Authorized Nilﬁ sk-Advance Service Center, who employs factory trained service personnel, and maintains an inventory of Nilﬁ sk-Advance original replacement parts and accessories.

Call the NILFISK-ADVANCE DEALER named below for repair parts or service. Please specify the Model and Serial Number when discussing your machine.

(Dealer, afﬁ x service sticker here.)

NAME PLATE

The Model Number and Serial Number of your machine are shown on the Nameplate on the machine. This information is needed when ordering repair parts for the machine. Use the space below to note the Model Number and Serial Number of your machine for future reference.

MODEL NUMBER ______________________________________________

SERIAL NUMBER ______________________________________________

TRANSPORTING THE MACHINE

CAUTION!

Before transporting the machine on an open truck or trailer, make sure that . . .

• The machine is tied down securely.

• All access doors and covers are secured (tape and strap as needed).

TOWING

CAUTION!

If the machine must be towed or pushed, make sure the Master On/Off Key Switch (A) is in the OFF position and do not move the machine faster than a normal walking pace (2-3 mph, 3-5kph) and for short distances only. Note: Disconnecting the wheel drive motor wiring connector will make a disabled machine easier to push.

OTHER MANUALS AVAILABLE FOR YOUR MACHINE

The manuals listed below can be found via Nilﬁ sk-Advance’s two electronic supported databases. They are:

• Nilﬁ sk-Advance Dealer Customer Zone

• Ezparts service / parts CD-Rom

• 56041591 – Instructions for Use (Danish, Norwegian, Swedish, Finnish)

• 56041592 – Instructions for Use (German, French, Dutch, Russian)

• 56041593 – Instructions for Use (Spanish, Portuguese, Italian, Greek)

• 56041594 – Instructions for Use (Estonian, Latvian, Lithuanian, Slovenian)

• 56041595 – Instructions for Use (Slovakian, Czech, Polish, Hungarian)

• 56041596 – Instructions for Use (English, Spanish)

• 56041703 – Instructions for Use (Turkish)

• 56042451 – Parts List

2 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

revised 5/07

CAUTIONS AND WARNINGS SYMBOLS

Nilﬁ sk-Advance uses the symbols below to signal potentially dangerous conditions. Read this information carefully and take the necessary steps to protect personnel and property.

DANGER!

Is used to warn of immediate hazards that will cause severe personal injury or death.

WARNING!

Is used to call attention to a situation that could cause severe personal injury.

CAUTION!

Is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property.

Read all instructions before using.

GENERAL SAFETY INSTRUCTIONS

Speciﬁ c Cautions and Warnings are included to warn you of potential danger of machine damage or bodily harm.

WARNING!

* This machine should only be used by properly trained and authorized persons. * While on ramps or inclines, avoid sudden stops when loaded. Avoid abrupt sharp turns. Use low speed down hills. Clean only while ascending (driving up)

the ramp.

* Keep sparks, ﬂ ame and smoking materials away from batteries. Explosive gases are vented during normal operation. * Charging the batteries produces highly explosive hydrogen gas. Charge batteries only in well-ventilated areas away from open ﬂ ame. Do not smoke while

charging the batteries.

* Remove all jewelry when working near electrical components. * Turn the key switch off (O) and disconnect the batteries before servicing electrical components. * Never work under a machine without safety blocks or stands to support the machine. * Do not dispense ﬂ ammable cleaning agents, operate the machine on or near these agents, or operate in areas where ﬂ ammable liquids exist. * Do not clean this machine with a pressure washer. * Do not operate this machine on ramps or inclines of more than a 2 percent gradient. * Only use the brushes provided with the appliance or those speciﬁ ed in the instruction manual. The use of other brushes may impair safety.

CAUTION!

* This machine is not approved for use on public paths or roads. * This machine is not suitable for picking up hazardous dust. * Use care when using scariﬁ er discs and grinding stones. Nilﬁ sk-Advance will not be held responsible for any damage to ﬂ oor surfaces caused by scariﬁ ers or

grinding stones.

* When operating this machine, ensure that third parties, particularly children, are not endangered. * Before performing any service function, carefully read all instructions pertaining to that function. * Do not leave the machine unattended without ﬁ rst turning the key switch off (O), removing the key and securing the machine. * Turn the key switch off (O) and remove the key, before changing the brushes, and before opening any access panels. * Take precautions to prevent hair, jewelry, or loose clothing from becoming caught in moving parts.

* Use caution when moving this machine in below freezing temperature conditions. Any water in the solution or recovery tanks or in the hose lines could freeze,

causing damage to valves and ﬁ ttings. Flush with windshield washer ﬂ uid.

* The batteries must be removed from the machine before the machine is scrapped. The disposal of the batteries should be safely done in accordance with your

local environmental regulations.

* Do not use on surfaces having a gradient exceeding that marked on the machine. * All doors and covers are to be positioned as indicated in the instruction manual before using the machine. * Refer to “Onboard Battery Charger” section at back of manual for additional speciﬁ c battery charger warnings.

SAVE THESE INSTRUCTIONS

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 3

28C BA 725C

Convertamatic

brushes

(2) 27 in (69 cm)

W=31 in (79 cm)

L=55 in (140 cm)

H=44 in (112 cm)

26C

Convertamatic

24C

Convertamatic

32D BA 825

Convertamatic

28D BA 725

Convertamatic

26D

Convertamatic

Disc Cylindrical

brushes

(2) 25 in (64 cm)

brushes

(2) 23 in (58 cm)

holders

(2) 16 in (40.64

cm) brushes or pad

holders

brushes or pad

(2) 14 in (35.5 cm)

holders

brushes or pad

(2) 13 in (33 cm)

max 130 lbs max 80 lbs

W=29 in (74 cm)

L=55 in (140 cm)

H=44 in (112 cm)

W=27 in (69 cm)

L=55 in (140 cm)

32.6 in (83 cm) 36.6 in (93 cm) 36.6 in (93 cm)

43.25 in (109.85

cm)

.25 gal/min (.95 L/min) or 80 minutes per solution tank

.75 gal/min (2.8 L/min) or 27 minutes per solution tank

H=44 in (112 cm)

W=33.25 in (85

cm) L=55.5 in

(141 cm) H=44 in

(112 cm)

W=30 in (76 cm)

L=55.5 in (141 cm)

H=44 in (112 cm)

W=27.5 in (70 cm)

L=55 in (140 cm)

H=44 in (112 cm)

Convertamatic 24D BA 625

Technical Speciﬁ cations

Voltage 24 Volt

Power Source (4) 6 volt batteries (wet acid and gel cell available)

Onboard Battery Charger 24 volt, 25 amp Wet/Gel Compatible

Solution Control Precision-Flow electric pump

Solution Tank 20 gal. (76L)

Recovery Tank 20 gal. (76L)

Scrub Motors (2) .50 hp (375 watt)

Vacuum Motor 0.75 hp (560 watt) 3-stage

Sound Level 66 dB(A) at operator’s position

Drive System 0.4 hp (300 watt) variable forward and reverse, max speed =3 mph (4.83 km/hr), 10% gradeability

Drive Wheels (2) 7 in. (18cm) dia. foam-ﬁ lled, gray non-marking

Scrub Head Type

Scrub Path 24 in (61cm) 26 in (66cm) 28 in (71cm) 32 in (81cm) 24 in (61cm) 26 in (66cm) 28 in (71cm)

Max Productivity @ 2.8 mph 29,600 ft²/hr 32,050 ft²/hr 35,000 ft²/hr 39,424 ft²/hr 29,600 ft²/hr 32,050 ft²/hr 35,000 ft²/hr

(2,750m²/hr) (3,000 m²/hr) (3,200 m²/hr) (3,663 m²/hr) (2,750m²/hr) (3,000 m²/hr) (3,200 m²/hr)

Max Productivity @ 1.5mph 15,800 ft²/hr 17,200 ft²/hr 18,500 ft²/hr 21,120 ft²/hr 15,800 ft²/hr 17,200 ft²/hr 18,500 ft²/hr

(1468 m²/hr) (1598 m²/hr) (1719 m²/hr) (1962 m²/hr) (1598 m²/hr) (1598 m²/hr) (1719 m²/hr)

4 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

Regular

Scrub max 80 lbs max 60 lbs

Heavy Scrub

Extreme

Scrub max 160 lbs max 100 lbs

Regular

Scrub

Heavy Scrub .50 gal/min (1.9 L/min) or 40 minutes per solution tank

Extreme

Scrub

Pressure

Scrub Head Speed 220 rpm 900 rpm

Solution Flow

Scrub Head Size & Type (2) 12 in (30.5 cm) brushes or pad holders

Rate

Scrub

Squeegee Width 32.6 in (83 cm) 36.6 in (93 cm) 36.6 in (93 cm)

Dimensions (w/o squeegee) W=26 in (66 cm) L=54.5 in (138 cm) H=44 in (112 cm)

Weight w/ Batteries 780 lb (354 kg) 780 lb (354 kg) 780 lb (354 kg) 780 lb (354 kg) 780 lb (354 kg) 780 lb (354 kg) 780 lb (354 kg)

AXP / EDS

Reﬁ llable Cartridge Capacity 1.25 gal (4.75 L)

revised 5/07

Available Dilution Rates 32:1, 50:1, 64:1, 100:1, 128:1, 150:1, 200:1, 256:1, & 300:1

Low Detergent Warning Standard

SPECIFICATIONS

revised 5/07

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 5

MAINTENANCE SCHEDULE

Maintenance intervals given are for average operating conditions. Machines used in severe operational environments may require service more often.

MAINTENANCE ITEM Daily Weekly Monthly Yearly

Charge Batteries X Check/Clean Tanks & Hoses (clean recovery tank switches & vacuum inlet screen) X Check/Clean/Rotate the Brushes/Pads X Check/Clean the Squeegee X Clean Hopper on Cylindrical System X Purge Extended Scrub System (if installed) X Check Each Battery Cell(s) Water Level (does not apply to gel cell batteries) X Inspect Scrub Housing Skirts X Inspect and clean Solution Filter X Clean Solution Trough on Cylindrical System X Lubricate the Machine X * Check Carbon Brushes X

Note: See the individual machine system sections for maintenance information.

* Have Nilﬁ sk-Advance check the vacuum motor carbon motor brushes once a year or after 300 operating hours. The brush and drive motor carbon brushes check every 500 hours or once a year.

WARNING!

Turn the key switch off and disconnect the batteries before servicing the machine.

* Check vacuum motor carbon brushes (Qty 2) once a year or after 300 operating hours.

* Check brush and wheel drive motor(s) carbon brushes (Qty 4 per motor) once a year or after 500 operating hours.

* The original (new) length of each carbon brush is 1” (25.4mm) on all 24 volt machine models brush and wheel drive motors.

* All motors: Replace carbon brushes when shorter than 3/8” (9.5mm) to obtain the same motor efﬁ ciency as new brushes.

IMPORTANT!

Motor damage resulting from failure to service the carbon brushes is not covered under warranty. See the Limited Warranty Statement.

BATTERIES AND CHARGERS

Attention: See the ELECTRICAL SYSTEM section for battery installation, battery maintenance and charger system requirements.

LUBRICATING THE MACHINE

Once a month, apply light machine oil to lubricate the:

• General Pivot Points for the Squeegee Linkage (A).

• Squeegee mount angle adjustment knob threads (B).

• Squeegee Tool end wheels (C).

• General Pivot Points for the Brush Linkage (D).

• Scrub Deck Bumper Wheels. Once per quarter, Grease the following

• Rear Caster Wheel Swivel (E).

6 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

revised 8/05

Nilfisk-Advance Convertamatic™ 24/26/28/32 & BA 625, 725, 825

Cylindrical and Disc

PM Checklist

Defect Codes

Customer A needs adjustment

B binding

Address C dirty or contaminated

D damaged, bent or torn

City St Zip L leaks

M missing

Model Serial Hours W worn out

OPERATIONAL INSPECTION ITEMS

Ref

1 Drive Paddle Operation (check for Fwd/Rev Drive & any neutral creep) A B D

2 Drive System Performance (Speed Changes Min/Max) noisy sluggish

3 Scrub System (Raise/Lower, Brush Motor On/Off & Optional Brush Remove Feature) A B D

4 Scrub Brush Pressure settings (1-3) A B

5 Squeegee System (Raise/Lower & Squeegee Tool pickup Performance) A B D

6 Vac Performance (Sealed water lift & 1” open hole adapter, 24v-56/9) C L W

7 Solution Control (On/Off Manual /Auto and Flow Volume settings 1,2 &3) A B L

8 Battery Charger (Auto turn ON & OFF) D

9 Main Controller Special Program Options (see SVR manual 56043098). Check all applicable

machine settings. Examples: Scrub mode pressure settings, SVR test mode, low voltage cutout etc.

Defect Codes

(circle)

Does

Not

Work

VISUAL INSPECTION ITEMS

Ref

10 Scrub Brushes, check for wear and rotate D M W

11 Scrub Brush Motor(s), check for carbon brush wear 500 Hours B C W

12 Scrub Brush Motor(s), check gearboxes (disc) B D L

13 Brush Drive Plate Retainer Clips & flex couplers (disc) C D M

14 Scrub Deck Lift Motor, Skirt & Side Wheel D M W

15 Solution Solenoid Valve C L W

16 Solution Pump & Hoses C L W

17 Solution Tank, Delivery Hoses & Filter clean filter screen C L

18 Vacuum Motor Carbon Brushes (wear limit 3/8”) 300 Hours B C W

19 Vacuum motor inlet filter (located in recovery tank) clean screen C D M

20 Recovery Tank Cover Gasket L M W

21 Recovery Tank Drain Hose & Cap C D L

22 Squeegee Pick-Up Hose back flush C D L 23 Squeegee Tool & Blades (clean, rotate & adjust) A D W

24 Squeegee Tool lift cable & mount Wheels (lubricate) two side & one floor A D W

25 Battery Condition (load test, clean & water) C W

26 Drive Wheel Trans Axle Motor Check Carbon Brushes 500 Hours B C D W

27 Trans Axle Drive Tires tread wear W

28 Rear chassis Caster Wheel (Lubricate) tread wear W

Comments OK

Defect Codes

(circle)

NOTE: For additional service information see service manual form number 56043098 and operator manual form numbers 56041591-56041596 & 56041703.

WORK COMPLETED BY: ACKNOWLEDGED BY:

Does

Not

Work

Service Technician Signature Date Customer Signature Date

revised 5/07

KNOW YOUR MACHINE

As you read this manual, you will occasionally run across a bold number or letter in parentheses - example: (2). These numbers refer to an item shown on this page unless otherwise noted. Refer back to this page whenever necessary, to pinpoint the location of an item mentioned in the text. NOTE: Refer to the service manual for detailed explanations of each item illustrated on the next 3 pages.

1 Solution Tank Fill 2 Operator Control Handle 3 Bottle Holders 4 Vacuum Motor Inlet Screen 5 Recovery Tank Cover 6 Detergent (AXP / EDS) Cartridge Access Cover 6a Detergent (AXP / EDS) Cartridge (AXP / EDS models only)

7 Scrub Deck 8 Scrub Deck Skirt 9 Scrub Deck Bumper 10 Drive Wheel 11 Solution Filter 12 Squeegee Assembly 13 Solution Shut-Off Valve

8 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

revised 5/07

KNOW YOUR MACHINE

14 Solution Drain Hose / Level Indicator 15 Squeegee Raise / Lower Lever 16 Onboard Battery Charger (Not found on all models) 17 Wheel Drive Circuit Breaker 18 Control Circuit Circuit Breaker 19 Squeegee Blade Latch 20 Squeegee Mount Thumb Nut 21 Squeegee Adjustment Knob 22 Recovery Tank Drain Hose 23 Debris Hopper (Cylindrical Models Only) 24 Idler Assembly (Cylindrical Models Only)

25 Battery Pack Connector (non onboard charger models only) 25a Battery Pack Connector (onboard charger models only) 26 Squeegee Blade Tension Strap 27 Squeegee Blade Alignment Pins 28 Recovery Hose 29 Control Panel 30 Drive Paddle 31 Speed Limit Control Knob 32 Vacuum Shut Off Switch 33 Extended Scrub Filter (Optional) 34 Solution Manifold (Cylindrical Models Only)

revised 5/07

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 9

KNOW YOUR MACHINE

A Key Switch (Main Power) B Solution Switch C Vacuum Switch D Display Panel Solution Flow Indicator AXP / EDS Indicator Hour Meter Battery Indicator Scrub Pressure Indicator Recovery Tank FULL Indicator Fault Indicator E Wand Switch (Dealer Installed Option) F Detergent System (AXP / EDS models only) G Extended Scrub System (Dealer Installed Option) H Scrub OFF I Scrub ON

10 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

revised 5/07

KNOW YOUR MACHINE FUNCTIONAL DESCRIPTION OF CONTROL PANEL:

The controls on the Convertamatic / BA 625 series were designed with one touch operation in mind. For single pass scrubbing the user can simply depress one switch and all systems on the machine will be ready to go. For most single-pass scrubbing operations, the operator should only need to use the middle switches on the control panel. These are the Scrub System OFF and Scrub system ON switches.

Scrub OFF Switch (H) - Pressing this switch when the unit is in a scrub mode will cause the following to occur:

• The scrub brushes will turn off and the scrub deck will be raised to the up position

• The solution ﬂ ow will be stopped

• The ﬁ rst time that this switch is pressed, the vacuum system will NOT be turned off. This is so that any remaining water may be picked up without having to turn the vacuum back on. If this switch is pressed a second time (pressed after the scrub system has been turned off) the vacuum will shut of after a 10 second delay.

Scrub ON Switch (I) – If the scrub system is off, pressing this switch once will cause the following to occur:

• The scrub system will be enabled with the scrub pressure set to the regular setting and the scrub deck will be lowered. Note press twice for the heavy scrub pressure mode and hold this switch for 5 seconds to enter the extreme scrub mode.

• The vacuum system will be enabled.

• The solution system will be enabled.

• As soon as the throttle (operator drive paddle) is moved from the neutral position the scrub brushes will start turning and the vacuum will turn on. If the direction is forward the solution ﬂ ow will start. If the direction is reverse, the solution ﬂ ow will be stopped. If the scrub system is already enabled when this switch is pressed, the scrub pressure will increase to the heavy scrub mode. If the switch is held for 5 seconds the pressure will change to the extreme scrub mode. At the same time the panel display will show the correct changed scrub pressure setting.

Wand Switch (E) – This switch is used when an external vacuum/scrub wand is used. Pressing this switch will turn the vacuum on continuously without regard to the throttle position. If the scrub system was on it will be turned off. This includes turning off the scrub brushes and turning the solution ﬂ ow off (to the scrub deck). NOTE: automatic shutoff of the vacuum motor when the recovery tank is full is disabled when the wand is

enabled.

Key Switch (A) – Main power switch

Vacuum Switch (C) – This switch is used to turn the vacuum system on or off. Pressing this switch will alternate between on and off. The vacuum

will only turn on when the throttle is moved from the neutral position. It will remain on for 10 seconds after the throttle returns to neutral. The vacuum also has an automatic shutoff feature that will turn the vacuum and scrub systems off if the recovery tank becomes full.

Solution Switch (B) - This switch is used to turn the solution system on or off. Pressing this switch when the scrub system has been activated will alternate between on and off. The solution ﬂ ow will only turn on when the throttle is moved from the neutral position in the forward direction. The solution ﬂ ow will turn off if the throttle returns to neutral or is moved to reverse. Pressing this switch when the scrub system is off will momentarily turn the solution ﬂ ow on to allow pre-wetting of the scrub brushes.

Chemical Switch (F) – Pressing this switch will turn on or off the chemical option. See the main programming options in this manual to select (activate) the onboard chemical distribution system.

Extended Scrub (Recycle) Switch (G) - Pressing this switch will turn on or off the recycle option. See the main programming options in this manual to select (activate) the recycle option.

revised 5/07

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 11

KNOW YOUR MACHINE DESCRIPTION OF INDICATORS ON THE CONTROL PANEL:

In general, the following guidelines apply to the control panel indicators: A ﬂ ashing green or yellow indicator means that a fault has occurred in the particular system. An example of this would be an over-current fault. A yellow indicator means that the particular function has been enabled but is not currently on. For example, if a scrub mode is selected and the throttle is in neutral, the scrub system, vacuum, and solution indicators will all be yellow indicating that the systems are enabled and ready to turn on when the throttle is moved to forward or reverse. A green indicator means that the particular system is on. A ﬂ ashing green indicator means that the particular system is in a delayed-off condition. An example of this is when a scrub mode is selected and the throttle goes from forward or reverse to neutral. When this happens the vacuum indicator will ﬂ ash green indicating that the vacuum is still on but that it will be turning off after the delay period.

Scrub OFF Indicator (J):

• This indicator will be green if the scrub system is off and ready to be activated.

• This indicator will be red if the scrub system has been turned off and the scrub deck is not up yet.

• This indicator will ﬂ ash red if there is a fault in the scrub system.

• This indicator will be off if the scrub system has been activated.

Regular Scrub ON Indicator (K):

• This indicator will be yellow if the scrub system is enabled in “Regular” scrub mode but the drive paddle is in neutral.

• This indicator will be green if the scrub system has been turned on in “Regular” scrub mode and the machine is moving in either direction.

• This indicator will be off if the scrub system has been turned OFF.

Heavy Scrub ON Indicator (L):

• This indicator will be yellow if the scrub system is enabled in “Heavy” scrub mode but the drive paddle is in neutral.

• This indicator will be green if the scrub system has been turned on in “Heavy” scrub mode and the machine is moving in either direction.

• This indicator will be off if the scrub system has been turned OFF.

Extreme Scrub ON Indicators (K & L):

• Both of these indicators will be yellow if the scrub system is enabled in “Extreme” scrub mode but the drive paddle is in neutral.

• Both of these indicators will be green if the scrub system has been turned on in “Extreme” scrub mode and the machine is moving in either direction.

Control panel LED Display (D):

See the detailed drawing shown in the Know Your Machine manual section for the speciﬁ c description of the individual icon symbols. NOTE: If a speed control fault occurs (error code 3) the wand indicator will ﬂ ash the fault code produced by the Curtis speed control. Refer to the service manual troubleshooting section for details.

Wand Switch Indicator (M):

• This indicator will be green if the Wand Switch has been turned ON.

• This indicator will be off if the Wand Switch has been turned OFF.

Vacuum System Indicator (N):

• This indicator will be green if the vacuum is on.

• This indicator will ﬂ ash green if the vacuum is in the 10 second delayed-off condition.

• This indicator will be yellow if the vacuum is enabled but the drive pedal is in neutral.

• This indicator will ﬂ ash yellow if there is a vacuum system fault.

• This indicator will be off if the vacuum is disabled and turned off.

Solution System Indicator (O):

• This indicator will be green if the solution is on.

• This indicator will be yellow if the solution is enabled but the drive paddle is in neutral.

• This indicator will ﬂ ash yellow if there is a solution system fault.

• This indicator will be off if the solution is disabled and turned off.

Chemical “AXP / EDS” System Indicator (P):

• This indicator will be green if the AXP / EDS system is on.

• This indicator will be yellow if the AXP / EDS system is enabled but the drive paddle is in neutral.

• This indicator will be off if the AXP / EDS system is disabled and turned off.

Extended Scrub System Indicator (Q):

• This indicator will be green if the Extended Scrub system is on.

• This indicator will be yellow if the Extended Scrub system is enabled but the recovery tank switches haven’t been activated.

• This indicator will be off if the Extended Scrub system is disabled and turned off.

12 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

revised 5/07

SOLUTION SYSTEM FUNCTIONAL OVERVIEW

See Figure 1. The Convertamatic / BA 625 series models have a solution tank ﬁ ll capacity of 20-gallons (76 liters). All models use one right rear tank ﬁ ll opening,

which offers ease of ﬁ lling. Plumbed into the manual solution shut off valve outlet is a serviceable Solution Filter (C), to keep debris from entering the solenoid valve. Also ﬁ tted to the tank is a ﬂ exible Clear Hose (B) used to indicate the solution level and to drain the tank for system maintenance.

The standard solution system uses an electrical Solenoid Valve (L1) which stops and starts the solution ﬂ ow to the scrub brushes. The M7 water pump (A) located on the machine chassis controls the needed ﬂ ow volume demand to the scrub brushes. See Electrical Diagram Figure 2. The electrical circuit that turns on (energizes) the solenoid coil and water pump is activated through the (A1) control panel’s solution switch button input and the FWD / REV (A2) Speed Controller voltage output signals. Note: See the Know Your Machine section in this manual for a complete explanation of the solution operation modes.

During normal machine scrubbing the solution system’s Auto Mode is selected and works in conjunction with the wheel drive speed controller and the (A1) main controller’s scrub system outputs to turn On & Off the (L1) solenoid valve and pump. The solution will ﬂ ow to the scrub brushes when the scrub deck is lowered and the handle drive paddle (box) is pushed Fwd. Note: When the solution On/Off button is turned Off, no ﬂ ow can occur while the machine scrub deck is down and the drive paddle activated.

*Note: Figure 1 shows the solution components of a machine with the Chemical System. The Chemical Tank Assembly is not found on all models.

FIGURE 1

revised 5/07

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 13

SOLUTION SYSTEM CIRCUIT OVERVIEW SOLUTION AUTO MODE (SOLENOID VALVE CIRCUIT)

See Figure 2. + (Positive) circuit input starts with:

• A closed S3 key switch will direct the needed positive voltage (BRN wires) to the L1 solenoid coil and A1 control board terminal #J1-13.

- (Negative) circuit input starts with:

• A battery negative ground input at the A1 control board terminal #B2 (J1-9)

• The A1 control board solution button enabled.

• A negative voltage output from the A2 speed controller’s (pin #6) Red/Blk wire to the A1 control board Red/Blk wire (terminal J1-5). Note: The A2 speed controls brake output (pin #6) occurs whenever the R1 direction throttle pot is moved off its neutral setting.

• A negative voltage output from the A1 board’s terminal J1-11 Red/Grn wire is direct to the L1 solenoid coil turning it on to allow ﬂ ow through the valve body.

CIRCUIT OVERVIEW SOLUTION AUTO MODE (SOLUTION PUMP CIRCUIT)

See Figure 2. + (Positive) circuit input starts with:

• With the batteries connected the needed positive voltage (Red wires) to the M7 Solution Pump.

- (Negative) circuit input starts with:

• A battery negative ground input at the A1 control board terminal #B4 (J2-6)

• The A1 control board solution button enabled.

• A negative voltage output from the A1 board’s terminal J1-8 Grn/Blk wire is direct to the M7 Solution Pump turning it on to allow ﬂ ow to the L1 Water Valve

Solenoid. NOTE: The solution pump’s output volume is controlled by the A1 board’s programmable capability and changes the pulsing of the negative battery connection to the pump.

Electrical Diagram

*For complete description of all callouts see Electrical System Wiring Diagram.

FIGURE 2

RED

CIRCUITBREAKER,5AMP

RED

CIRCUITBREAKER,30AMP

1210SPEEDCONTROLLER

MOTOR,WHEELDRIVE

(1228FOR36V)

BRN/BLK

YEL/RED

GRN

RED

FUSE,150A.

SW,SPSTKEY

WHT/YEL

RED

BRN

COIL,SOLUTIONSOLENOID

BLK

B+ B-

PIN9-STATUS

PIN6-BRAKE(-)

PIN16-REV

PIN5-KSI

PIN13-POT.LO

PIN4-POT.WIPER

PIN3-POT.HI

PIN18-SPEEDLIMITPOT

BT1

BATTERY

24VDCOR36VDC

BRN

WHT BLU BLK BRN

POT.100KOHMSPEEDLIMIT

BRN

RED/GRN

RED/BLK BLU/BLK

BLU

BRN

WHT

BLK

J1-13

J1-11

B+1

SOLUTION

J1-9

B-2

J2-6

B-4

BLK

CONTROLBOARD

J1-8

SOL.PUMP

J1-7

FOR/REV.

REVERSE

J1-5

J1-6

RED/BLK

BLU/BLK

WHT

BLK

R1 POT.5KOHMTHROTTLE

B-1

NOTE:SWITCHISPARTOF PUMPASSEMBLY

SOLUTIONPUMP

BLK

GRN/BLK

14 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

SOLUTION SYSTEM SOLUTION SYSTEM MAINTENANCE

• Solution Tank: See Figure 1. Weekly empty the solution tank; remove the solution Drain Hose (B) from its storage area (located on the right rear control handle

compartment). Direct the hose to a designated “Disposal Site” and ﬂ ush the tank with clean water.

• Solution Filter: Remove and clean the inline Solution Filter (C). To access the ﬁ lter housing for removal, work underneath the middle left side chassis panel. No tools are needed to remove the ﬁ lter (hand tighten only). Service Tip: The solution ﬁ lter ball valve must be placed in the OFF (Closed) position. This prevents loss of solution when servicing the ﬁ lter strainer with a partial or full tank.

• Solution Delivery Trough: On the cylindrical scrub deck clean the holes in the delivery trough to assure even distribution of solution.

TROUBLESHOOTING GUIDE

Problem Possible Cause

Inadequate or no solution ﬂ ow No solution in the tank

Solution tank ﬁ lter ball valve in the off position

Clogged solution ﬁ lter, valves and hoses

*Reference the Solution System Troubleshooting Guide ﬂ owchart in this manual section for further component diagnostics.

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 15

SOLUTION SYSTEM TROUBLESHOOTING GUIDE ELECTRICAL

Possible Symptoms

1-No solution ﬂ ow while in the scrub auto solution mode. 2-Solution Pump will not operate:

SYMPTOM ONE

Note: Activate the Service Test Mode Program. See optional program section for instructions.

All testing will be performed in the Service Test Mode Program.

16 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

SOLUTION SYSTEM TROUBLESHOOTING GUIDE ELECTRICAL (CONTINUED)

SYMPTOM TWO

Note: Activate the Service Test Mode Program. See optional program section for instructions.

All testing will be performed in the Service Test Mode Program.

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 17

SOLUTION SYSTEM SOLENOID VALVE REMOVAL

Drain the solution tank or turn the solution ﬁ lter ball valve to the off position to prevent solution loss.1 Lower the deck and disconnect the battery supply to the machine.2 Remove the front Nose Cone from the machine by ﬁ rmly grasping the lower part and lifting straight up.3 See Figure 3.4 Unplug the L1 solenoid valve wire assembly connection from the machine harness. Unscrew the inlet Hose Clamps 5 (D) that secure the hoses to the valve body. Separate (pry) the solution outlet hose off from its valve body barbed ﬁ tting.6 Remove the (2) Hex Screws 7 (E) that secure the valve to the Mount Bracket (F), then pull the valve body to the front separating it from the solution inlet Hose

(G), completing the part removal.

SOLENOID VALVE DISASSEMBLY AND CLEANING

1 Remove the solenoid valve. See the Solenoid Valve Removal section for instructions. 2 See Figure 3. Remove the (4) (H) Screws and disassemble the valve (be careful not to lose any internal parts). 3 Thoroughly wash dirt from block (I) and diaphragm (J). 4 After reassembling, test the solenoid valve for proper operation.

FIGURE 3

18 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

revised 5/07

SOLUTION SYSTEM SOLUTION FILTER AND BALL VALVE REMOVAL

1 Drain the solution tank using the solution drain hose (B). 2 See Figure 4. Loosen the (2) Hose Clamps (K) and pry off the inlet Solution Hose (L) and Solution Hose (M). 3 Remove the Nut (N) that secures the Filter Mount Bracket (O) to the chassis and remove the assembly from the machine.

FIGURE 4

SOLUTION PUMP REMOVAL

Drain the solution tank or turn the solution ﬁ lter ball valve to the off position to prevent solution loss.1 See Figure 4.2 Loosen the (2) Hose Clamps (P) and pry off inlet Hose (M) and outlet Hose (Q) from Solution Pump (R). Remove the (2) 10-24 nuts 3 (S) that secure the Solution Pump to the Chassis. Disconnect the Solution Pump Electrical Connector 4 (T); (A tie strap may need to be cut) completing the part removal.

NOTE: Refer to the APPENDIX at the back of this manual for solution system ﬂ ow schematics and detergent system information.

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 19

SCRUB SYSTEM FUNCTIONAL OVERVIEW

• Disc Brush System Overview

See Figure 2. The machine models Convertamatic™ 24D, 26D, 28D, 32D / BA 625, 725, 825 use the disc type scrub system powered by (2) 1/2 hp motor gearbox

assemblies.

• Cylindrical Brush System Overview

See Figure 4. The machine models Convertamatic™ 24C, 26C, 28C / BA 725Cuse two cylindrical brushes that counter rotate to sweep up light debris and scrub at

the same time. Each scrub brush is powered on opposing ends by 1/2 HP permanent magnet motors attached to separate poly-V belt/pulley drives.

• General Brush Overview

Note: Recovery Tank Full switch must be closed (Tank empty). On all models the scrub deck platform is raised & lowered automatically by a vertically mounted

electric lift actuator motor. The operation of the machine’s scrub functions are activated when the operator selects (presses) the scrub on (mode) panel button. The scrub pad or brush pressure ranges (1-3) are selectable allowing the operator the choice to vary the scrubbing effort (pressure) while operating the machine. Note: See the Main Control Board Special Program Options section in this manual for more detailed operation and instructions to change scrub pressure settings.

See Figure 1. The machine’s main scrub system input and output operating functions are regulated (managed) by the display panel and combined main control board A1. The major scrub system functions are…

• M2 / M3 - Scrub Brush Motor Run Function

Circuit Overview Scrub Brush Motor

+ (Positive) Circuit input starts with:

• A closed S3 key switch supplies the needed positive voltage to the K1 brush solenoid coil and the A1 control board #J1-13 (Brn wire). Note: The A1 control board scrub-on button must also be depressed (enabled). This operator command lowers the brush deck. Once the K1 load is closed the needed Positive voltage is supplied to the motors M2 and M3.from battery Pos.

- (Negative) Circuit input starts with:

• A battery negative ground input at the A1 control board terminals B2 (J1-9) Blk and B1 (J1-7) Blk.

• Note: The A1 control board scrub-on button must also be depressed (enabled).

• A negative voltage output from the A2 speed controller’s Neg. (pin #6) Red/Blk wire to the A1 control board Red/Blk wire (terminal J1-5). Note: The A2 speed control brake output (neg.) (pin #6) occurs whenever the R1 direction throttle pot is moved off its neutral setting.

• A negative voltage output from the A1 board’s terminal (J1-14) Vio/Blk wire completes the K1 solenoid coil circuit (Pos. & Neg.) and pulls in the load contact making the brush motors run.

The Neg. M2 and M3 load voltage is supplied from the battery Neg.

• M5 - Scrub Brush Actuator Lift Motor Function

The A1 control board outputs a controlled motor voltage polarity change (wires J2-1 and J2-8) that raises and lowers the scrub-deck for installing, removing and controlling the scrub brushes’ selected current load. The large BLK negative (-) scrub brush motor wire is specially designed so that it has a known (speciﬁ ed) resistance value. As brush motor current passes through the negative wire that is, in effect, a low value resistor, a small voltage drop is developed across it which is proportional to the motor current. This voltage change is inputted to the A1 control board at J2-5 and J1-7(sense wires WHT/GRA & BLK). Any surrounding temperature change in this large Neg. motor wire affects its resistance so the temperature is sensed by a thermistor (*) built into the control board A1. This allows the controller to provide error correction for the temperature resistance changes. When the controller senses a current draw out of the desired range it automatically turns on the M5 actuator motor to raise or lower the scrub deck. This process is on going in maintaining the operator’s selected scrub motor current load setting to sustain the desired brush working pressure.

• Scrub System Low Voltage Cut-Out Function

The purpose of the special low battery voltage cutout function is to help prolong battery life. The scrub deck will be raised and the brush motors and solution solenoid valve will turn OFF automatically and cease to function when the batteries discharge to the selected cutout level. The cutout level is adjustable between two settings. The standard setting (wet cell/lead acid) is 1.72 volts per cell and alternate setting (gel/maintenance free) is 1.81 volts per cell. Note: See the battery system section for instructions for selecting (setting) the two different thresholds.

SPECIAL SCRUB SYSTEM FUNCTIONS

• Scrub Brush Removal Function (Disc only)

For removal of the scrub brushes automatically, the scrub deck must be in the up position and the drive system in neutral. To remove the scrub brushes simply depress the control panel scrub-off button (H) for 2-3 seconds. The A1 control board will momentarily run the brush motors and then stop them quickly, where the brushes inertia causes the brushes to easily spin off of the scrub brush motors drive caps.

20 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

revised 5/07

SCRUB SYSTEM

• Scrub Brush Removal Function (Continued / Disc only)

• Control and Load circuit detail.

A closed S3 key switch supplies the needed positive voltage to the K1 brush solenoid coil, A1 control board (J1-13) Brn wire and K3 brush remove coil relay

(Part of A1 Control Board).

- The brush remove circuit sequence starts when the operator depresses the control panel scrub off button (H) for 2-3 seconds activating the A1 board’s brush remove function. This triggers (starts) an internal timer relay closing the K1 coil ground circuit, pin (J1-14) Vio/Blk wire turning on momentarily the brush solenoid to run the brush motors.

- Simultaneously with the K1 coil being turned on the same input command closes the K3 coil (Part of A1 Control Board) turning it ON.

- This pulls in the K3 load contacts (Part of A1 Control Board) connecting it to the battery ground through the A1 Brush Remove circuit N.O. Blk wire and Common Blu/Wht wire to K1 Load Contactor N.C

- The next step is the board timer turning off the K1 brush solenoid and connecting the normally Pos. motor load circuit to a battery ground, sending a neg. voltage from the K3 Relay (Part of A1 Control Board) though the Blu/Wht N.O. wire. When K1 is de-energized the neg. voltage from the K3 relay is connected to the Brush Motors Positive Wht. wires through a Red/Wht jumper wire connected to the K1 N.C.

- With two battery ground inputs at the brush motors this circuit causes a short to ground and the motors stop abruptly. The built up brushes inertia easily spins the brushes off the motors drive disc lugs.

FIGURE 1

RED

RED CIRCUIT BREAKER, 5AMP

WHT

RED

BRN

VIO/BLK

BLU/WHT

GRN

FUSE,150A.

SW,SPSTKEY

RED/WHT

GRN

RED

BRN

COIL BRUSH MOTOR CONTACTOR

BT1

BATTERY

24VDC OR 36VDC

VIO/BLK

CONTROLBOARD

J2-7

B+2

J1-13

B+1

J1-14

BRUSH CONTACTOR

J1-5

BLK

J1-3

J2-3

J2-2

INPUT

SUPPLY

BRUSH ACTUATOR-2 BRUSH ACTUATOR-1

BRUSH

REMOVE RELAY

FOR/REV.

BRUSH MOTOR SENSE

REVERSE

J2-5

J1-6

J2-9

B-3

J2-6

B-4

J2-1 J2-8

RELAYN.O.

RELAYCOMMON

J1-7

B-1

J1-9

B-

B-2

BLK BLK BLK

VIO/YEL WHT/GRN MOTOR, BRUSH ACTUATOR

BLK

RED

CIRCUIT BREAKER, 30AMP

1210 SPEED CONTROLLER

(1228 FOR 36V)

BRN/BLK

MOTOR, WHEEL DRIVE

RED

YEL/RED

BLU/WHT

WHT/YEL

BLK

B+ B-

PIN9-STATUS

PIN6-BRAKE(-)

PIN16-REV

PIN5-KSI

PIN13-POT.LO

PIN4-POT.WIPER

PIN18-SPEED LIMIT POT

PIN3-POT.HI

WHT

BRN

ORN/BLU RED/BLK BLU/BLK

WHT BLU BLK BRN

POT.100K OHM SPEED LIMIT

POLARITY FOR DISC BRUSHES

WHT

MOTOR, LEFT BRUSH

MOTOR, RIGHT BRUSH

BLK

BLU

BRN

WHT

BLK

WHT

WHT/GRA

BLK

WHT/GRA

RED/BLK

BLU/BLK

R1 POT.5KOHMTHROTTLE

BLU/WHT

BLK

BLU/WHT

BLK

FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825 - 21

SCRUB SYSTEM SCRUB BRUSH DECK REMOVAL (DISC)

1 Lower the scrub deck with brushes (pads) installed. Turn the key switch off and disconnect the battery pack. 2 Lift up and remove cover and nose cone, from front of machine. 3 See Figure 2. Separate the solution system water line (A) located on top of the scrub deck. 4 Unplug both of the brush motor wiring harnesses (B). NOTE: Cable ties may need to be cut. 5 Remove the lower Hitch Pin (C) that secures the brush deck lift actuator to the scrub deck. Note: Lift up on the scrub deck to take pressure off the Pin (C). Service Note: It is

important that the actuator motor is not run while it is disconnected from the deck or chassis mounts. This precaution will prevent the actuator drive nut from being misadjusted (moved out of its set speciﬁ cation).

6 Remove the Cotter Pin (D) and washers that attach the Upper Hitch Pin (E) to the machine chassis Linkage Arm (F). NOTE: Reference Conﬁ g (A) or (B) depending on what your

machine looks like. 7 Remove the two (G) Hitch Pins that attach the scrub deck to the machine’s chassis Linkage Arms (H). Then rotate the Arms (H) out of the way. 8 From the front of the machine swing the lower actuator housing forward to clear the deck mount bracket (remove the actuator on AXP™ / EDS™ models). Then slide the deck

towards the left side of the machine until Pin (E) – Conﬁ g A is clear of Arm (F) – Conﬁ g A or until Arm (F) – Conﬁ g B is clear of the tank bracket. Pull the deck forward away from

the machine to complete the removal. SERVICE NOTE: It is important that the actuator motor is not run while it is disconnected from the deck or chassis mounts. This precaution

will prevent the actuator drive nut from being misadjusted (moved out of its set speciﬁ cation). 9 To install a scrub deck, follow the above steps in reverse order.

SCRUB BRUSH LIFT ACTUATOR REMOVAL (DISC.)

1 See Figure 2. With scrub brushes installed, lower the scrub deck, turn the key off and disconnect the battery pack. Note: If the lift actuator motor will not run go to step 2 and

perform the following, shim up the brush deck to remove the weight on the lower deck Actuator Pin (C) to remove. 2 Remove the front nose cone by ﬁ rmly grasping the lower part and lifting straight up. 3 Disconnect the actuator motor wiring harness pig tail connector. 4 Remove the lower actuator mount Pin (C). Note: Lift up on the scrub deck to take pressure off the pin (C). 5 Remove the Pin (I) from the upper actuator mount weldment and remove the motor. 6 See *Important Service Note below. 7 Reinstall in reverse order.

*Important Service Note: After removing any actuator motor and before installing a new motor or drive nut the IN and OUT limit switches must be set (or checked) to their correct speciﬁ cations. Reference the Electrical System in this manual for the Actuator Drive Nut Adjustment and follow these instructions before replacing the actuator motor. After setting the correct actuator nut adjustments for the scrub brush lift motor, follow removal steps in reverse order to reassemble.

SCRUB BRUSH MOTOR/GEARBOX REMOVAL (DISC)

Follow the steps in the 1 Scrub Brush Deck Removal (Disc) section.

Turn the brush deck on its back.2

Remove the scrub brushes from the brush holders. If removing both motor/gearboxes mark the location of the holders and motors to the brush deck for proper re-assembly.3

See Figure 3.4 Remove the (3) (J) Hex Screws from the ﬂ exible coupler that attaches the brush holder to the drive Hub (K) of the Motor/Gearbox Assembly you want to remove.

Remove the (1) Hex Screw 5 (L) that secures the Hub (K) to the output shaft on the defective motor/gearbox. Then pull the hub from the shaft and save the key.

Remove the (4) 6 (M) Screws and separate the defective Motor/Gearbox Assembly (N) from the scrub deck.

Re-assemble in reverse order and test for proper operation. Note: Apply a small amount of grease or a product called “Never Seize” to the gearbox output shaft when reinstalling 7

the Drive Hubs (K).

FIGURE 3

22 - FORM NO. 56043098 - Convertamatic™ 24, 26, 28, 32 / BA 625, 725, 825

revised 7/07

+ 55 hidden pages