Nilfisk-ALTO Poseidon PE, Poseidon DE, POSEIDON 2-31 PE, POSEIDON 3-36 PE, POSEIDON 5-47 PE Operating Instructions Manual
...Page 1
106169229 c
Operating
instructions
POSEIDON PE/DE
Page 2
Printed in Hungary
Copyright © 2012 Nilfisk-ALTO
Instruktionsbog ................................................. 3 - 15
User manual ..................................................... 16 - 28
Betriebsanleitung .............................................. 29 - 41
Manuel d‘instructions ........................................ 42 - 54
Manuale di istruzioni ......................................... 55 - 68
Manual de instrucciones ................................... 69 - 82
Үхειριδιο οδηуιων .............................................. 83 - 96
Manual de Instruções ....................................... 97 - 110
Руководство ..................................................... 111 - 124
Instrukcja obsługi .............................................. 125 - 138
Návod k obsluze ............................................... 139 - 151
Üzemeltetési útmutató ...................................... 152 - 164
Návod na používanie ........................................ 165 - 177
Gebruikershandleiding ...................................... 178 - 194
Page 3
16
POSEIDON PE/DE
Original Instructions
Contents
Symbols
1 Important safety notes
2 Description
3 Before starting the
pressure washer
4 Operation and use
5 After using the pressure
washer
6 Maintenance
7 Troubleshooting
8 Further information
...............................................................................................17
...............................................................................................17
2.1 Intended use ...........................................................................19
2.2 Operating elements ................................................................19
3.1 Setting up the pressure washer ..............................................20
4.1 Connections ...........................................................................20
4.2 Start the pressure washer ......................................................21
4.3 Using detergents ....................................................................22
5.1 Switching off the pressure washer .........................................23
5.2 Disconnecting supply lines .....................................................23
5.3 Storing the cleaner (frost-free) ...............................................23
6.1 Maintenance plan ...................................................................24
6.2 Maintenance work ..................................................................24
...............................................................................................26
8.1 Recycling the pressure washer ..............................................27
8.2 Guarantee ..............................................................................27
8.3 Technical data ........................................................................28
8.4 Declaration of Conformity .......................................................28
Page 4
17
POSEIDON PE/DE
Original Instructions
Symbols Before starting
up your highpressure washer
for the fi rst time,
this instruction
manual must be
read through carefully. Save the
instructions for later use.
Safety instructions
marked with this
symbol must be
observed to
prevent danger
to persons.
This symbol is used
to mark safety
instructions
that must be
observed to prevent
damage to the machine and its
performance.
This symbol
indicates tips
and instructions to
simplify work and to
ensure a safe operation.
Before using the high-pressure
washer, be sure to also read the
enclosed operating instructions
and keep them within reach at
all times.
The high-pressure washer
may only be used by persons
instructed in its use and
who have been expressly
authorised to do so.
General
Use of the high-pressure
washer is subject to the
applicable local regulations.
In addition to the operating
instructions and the binding
accident prevention regulations
in the country of use, the
generally recognised rules
for safe working must also be
observed.
Any method of use endangering
the safety of persons or
equipment is forbidden.
Before use
Before use, check that the highpressure cleaner is in a safe
and proper condition.
Operate the pressure washer
only in an upright position!
Important notes:
Do not connect the pressure
washer directly to the public
drinking water mains (observe
DIN 1988 and EN 1717).
A connection is permitted,
however:
• briefl y to a pipe interrupter
with moving section
• with a free outlet
Water may also be drawn from
an open container or from
a well or surface water not
intended for the drinking water
supply. Please use suction set
for this. Ensure that neither dirty
water nor liquids containing
solvents are sucked in.
Please observe the regulations
and provisions applicable in
your country. Before putting
the high-pressure washer into
service, carry out a visual check
of all the major components.
High-pressure jets can be
dangerous if misused. The
jet must not be directed at
persons, animals, live electrical
equipment or the pressure
washer itself.
During operation of the washer,
recoil forces are produced at
the spray lance and, when
the lance is held at an angle,
a torque is also created. The
lance must therefore be held
fi rmly in both hands.
Risk of injury!
Do not direct the jet towards
yourself or towards other
persons in order to clean
clothes or footwear.
Do not use the washer when
other people without protective
1 Important safety notes
Page 5
18
POSEIDON PE/DE
Original Instructions
clothing are in the working
area. Check that cleaning
will not result in dangerous
substances (e.g. asbestos, oil)
being washed off the object to
be cleaned and harming the
environment.
Do not clean delicate parts
made of rubber, fabric, etc. with
the round jet. Hold the nozzle
at a distance of at least 15 cm
when cleaning with the highpressure fl at jet.
Although extremely easy to
operate, children should not
be allowed to use the pressure
washer.
Do not use the high-pressure
hose for lifting loads.
Do not continue to use the
washer if the quick coupling
or high-pressure hose is
damaged.
Never use the machine in areas
where there is danger of fi re
or explosion. When using the
pressure washer, stand at least
1 m from buildings, etc.
Ensure an adequate air
circulation. Do not cover
the washer or operate it in
inadequately ventilated rooms!
The exhaust fumes are
dangerous!
Store the pressure washer
where it will not be exposed to
frost!
Never operate the pressure
washer without water. Even
brief shortages of water result
in severe damage to the pump
seals.
Maintenace and repair
CAUTION!
Before cleaning and servicing
the high pressure washer,
always remove the ignition
plug cable fi rst.
Carry out only the maintenance
operations described in the
operating instructions.
Use only original Nilfi sk-ALTO
spare parts. Do not make any
technical modifi cations to the
high pressure washer.
CAUTION!
High pressure hoses, fi ttings
and couplings are important
for the safety of the washer.
Use only high pressure parts
approved by the manufacturer!
CAUTION!
Failure to observe these
instructions can endanger your
safety.
Please contact the Nilfi skALTO service department or an
authorised specialist work-shop
for all other maintenance or
repair work!
Testing
The machine satisfi es IEC/EN
60335-2-79 standards.
The high pressure washer
should be examined as needed
or at least once a year by a
technician to make sure that it
is fail-safe.
Our service technicians are at
your disposal for assistance
and advice.
Safety device
The high pressure pump is
equipped with a safety valve
that redirects the by-pass
pressure back to the suction
side of the pump.
The safety device is set and
sealed at the factory and must
not be adjusted.
Page 6
19
POSEIDON PE/DE
Original Instructions
2 Description
2.1 Intended use This high pressure washer has
been designed for professional
use in
- agriculture
- transport industry
- construction industry
etc.
2.2 Operating elements
1 Start/stop switch
2 Lance
3 Holder for lance
4 Holder for high pressure hose
5 High pressure hose
6 Spray gun
7 Water connection and water
inlet fi lter
8 Connection for high pressure
hose
9 Pressure gauge
10 Oil level gauge
11 Regulation of water volume
12 Filling of oil
13 Detachable handle
1
2
3
4
5
6
7
8
9
10
12
11
13
Page 7
20
POSEIDON PE/DE
Original Instructions
3 Before starting the pressure washer
3.1 Setting up the pressure
washer
1. Before using the pressure
washer for the fi rst time,
check it carefully to detect
any faults or damage.
2. In the event of any damage
contact your Nilfi sk-ALTO
dealer immediately.
3. Check whether the oil level
is in the middle of the oil
inspection glass. This also
applies to machines with
gear.
4 Operation and use
4.1 Connections
4.1.1 Connecting the lance to
the spray gun
1. Pull the blue quick-release
grip (A) of the spray handle
backwards.
2. Insert the nipple of the spray
lance (B) into the quickrelease connection and
release it.
3. Pull forward the spray lance
or any other accessory to
ensure correct mounting
before starting the machine.
NOTE!
Always remove any dirt from
the nipple before connecting
the lanse to the spray gun.
4.1.2 Connecting the high
pressure hose and the
water hose
1. Connect the high pressure
hose to the high pressure
inlet by means of the quick
coupling. Use max. 50 m
extension hose.
2. Before connecting the water
hose to the washer, rinse the
water hose briefl y to prevent
sand and other dirt from
entering into the washer.
3. Open the tap.
(continued -->)
A
B
Page 8
21
POSEIDON PE/DE
Original Instructions
NOTE!
See chapter 8.3 for required
quantity of water and water
pressure.
In the case of poor water quality
(sand, etc.), we recommend
that a fi ne water fi lter is fi tted in
the water inlet.
4.1.3 Fuelling WARNING!
Always shut off the engine
and let it cool for at least two
minutes before fuelling.
Avoid spilling fuel.
If you do spill fuel when fuelling,
do not start the engine before
the spilled fuel has evaporated.
If the washer is on a trailer, any
fuel spills must be wiped up
before the machine is started.
Never expose the machine
to an open fl ame. Smoking is
prohibited during fuelling. Also
read the operating manual for
the fuel engine.
Note: Never operate the
ma chine in a closed room; the
exhaust fumes are dan ger ous.
Follow the safety instructions
in chapter 1!
4.2 Start the washer
4.2.1 Switching on the
washer when it is
connected to a water
supply
2. Unlock the spray gun and
activate it.
3. Lock the safety catch even
during short pauses.
NOTE!
Activate the spray
gun several times
at short intervals to vent the
system.
If it requires too much power to
start the engine, it can be
facilitated by removing the
spray lance and activate the
spray gun during startup.
4.2.2 Switching on the
washer when it is
connected to open
tanks (suction mode)
1. Before connecting the suction
hose to the washer, fi ll the
hose with water.
2. Start the washer.
3. Unlock the spray gun and
activate it.
4. When using this machine in
suction mode, fi rst ensure
that the system has been
bled of air by letting the
machine run without spray
lance mounted until all air
has escaped.
During work
breaks of more
than three minutes,
switch off the washer.
NOTE!
For automatic suction from a
tank, watercourse or similar
sup ply, the inlet hose must be
fi lled with water before you
start. The suction height
(continued -->)
1. Start the engine. (See the
operating manual for the fuel
engine.)
Page 9
22
POSEIDON PE/DE
Original Instructions
depends on the water
temperature. Max. suction
height (see section 8.3
Technical Data) is reached with
cold water (up to 8°C). With
70°C/60°C warm water, the
ma chine must be under or at
the water level.
4.2.3 Start POSEIDON PE + oil light indicators will turn
on.
2. Move the throttle lever to
SLOW or RUN position.
3. Push the start button until
the machine starts. Now the
charging + oil light indicators
will turn off. If not, stop the
machine immediately and
contact Nilfi sk-ALTO service
department.
4. The machine can be started
by means of the starter rope
if the battery has gone fl at.
See manual from Yanmar.
4.3 Using detergents Detergent can be added by
means of the detergent injector.
1. Dilute detergent according
to the manufacturer's
instructions.
2. Set the pressure to the
lowest setting on the lance.
CAUTION!
Never allow
detergent to dry
on the surface to be cleaned
as this may cause damage.
1. Switch on the ignition by
pushing the ON/OFF button
of the machine. The charging
If the water being suctioned
contains particles, a suction
fi lter must be mounted on the
end of the hose.
In case of risk of running sands,
a sand fi lter must be attached.
Page 10
23
POSEIDON PE/DE
Original Instructions
5 After using the washer
5.1 Stop the pressure
washer
1. Stop the engine.
2. Close the tap.
3. Operate the spray gun until
the wasser is depressurized.
4. Lock the safety catch.
Switching off POSEIDON DE
1. Stop the washer by moving
the throttle lever to STOP
position.
2. Switch off the ignition by
pushing the ON/OFF button.
The light indicators will now
turn off.
5.2 Disconnecting supply
lines
1. Shut the fuel cock.
2. Remove the water hose from
the washer.
5.3 Storing the washer
(frost-protected)
1. Store the pressure washer in
a dry room without danger of
frost.
IMPORTANT!
If the high-pressure washer
is stored in a room with
temperatures around or
below 0°C, anti-freeze should
be drawn into the pump
beforehand:
1. Remove the water inlet hose
from the washer.
2. Remove the lance.
3. Start the washer and stop it
again after max. one minute.
4. Connect the suction hose
to the water inlet of the
washer and place it in a tank
containing anti-freeze.
5. Start the washer.
6. Hold the spray gun over the
tank containing anti-freeze
and activate it to start suction
of anti-freeze.
7. During suction operate the
spray gun two or three times.
8. Lift the suction hose from the
tank containing anti-freeze
and activate the spray gun to
pump out the remaining antifreeze.
9. Stop the washer.
Page 11
24
POSEIDON PE/DE
Original Instructions
6 Maintenance
6.1 Maintenance plan
weekly
every six
months or
500 operating
hours
as required
6.2.1 Clean water fi lter
•
6.2.2 Clean high pressure nozzle
•
6.2.3 Check oil level
•
6.2.4 Change oil - Note: First time after 50 hours
•
Maintenance of motor according to separate operating instructions from the engine supplier
6.2 Maintenance work
6.2.1 Clean water fi lter
A water fi lter is fi tted on the
water inlet to prevent large
particles of dirt from entering
into the pump.
1. Unscrew the union nut.
2. Remove the fi lter and rinse it.
Replace damaged fi lter.
3. Tighten the union nut gently,
so as to avoid damaging the
gasket.
6.2.2 Clean high pressure
nozzle
A blocked nozzle causes
excessive pump pressure. It
must therefore be cleaned
immediately.
1. Stop the washer.
2. Remove the lance.
3. Clean the nozzle with a
needle.
4. Rinse the lance with water
from the nozzle side.
WARNING!
Use the cleaning needle only
when the spray lance has been
removed.
NOTE!
The fuel engine
stops automatically
if the oil level is low. You can
start the petrol engine again
once you have added oil (does
not apply to POSEIDON 2-31
PE).
Page 12
25
POSEIDON PE/DE
Original Instructions
6.2.3 Checking the oil level 1. Check whether the oil level
is in the middle of the oil
inspection glass. Top up with
oil if necessary (see section
8.3 for type of oil).
6.2.4 Changing the pump/
gear oil
1. Before changing the oil,
allow the pressure washer to
become warm.
2. Unscrew the plugs at the top
and the bottom of the pump.
3. Allow the oil to drain into a
suitable container (min. 1 l
capacity) and dispose of oil in
compliance with regulations.
4. Mount plug at the bottom of
the pump.
5. Fill pump with fresh oil (see
8.3 for oil type and quantity).
6. Check the oil level (see
6.2.3).
Page 13
26
POSEIDON PE/DE
Original Instructions
7 Troubleshooting
Fault
Pressure drop
Pressure fl uctuations
In suction mode
Excess pressure
The motor does not start
Cause
> Air in the system
> High-pressure nozzle
blocked/worn
> Pressure control on the lance
is not set correctly
> Engine speed too low
> Lack of water
> Pump/accessories partially
frozen
> Water inlet hose is too long or
its cross-section too small
> Lack of water caused by
blocked water fi lter
> Lack of water because max.
permissible suction height
has not been heeded
> Water too hot
> Pump draws in air (only
possible in suction mode)
> Engine’s throttle control is
defective (accessory)
> Low fuel level
> Low oil level in engine
> The pump is blocked or
frozen
Remedy
• Vent the system by operating
the spray gun several
times at short intervals. If
necessary, dismount the
lance (see section 4.2.2).
• Clean/replace the highpressure nozzle.
• Set the required working
pressure.
• Contact Nilfi sk-ALTO Service
Department.
• Open the tap.
• Thaw machine and
accessories.
• Use prescribed size of water
inlet hose.
• Clean the water fi lter in the
water connection (never
operate the machine without
water fi lter mounted!)
• See chapter 4.2.2.
• See chapter 4.2.2.
• Check that the suction set is
air-tight. Repeat aeration.
• Give less gas/contact Nilfi sk-
ALTO Service Department.
• Open fuel cock/fi ll with fuel.
• Fill with oil.
• Thaw machine/contact
Nilfi sk-ALTO Service
Department.
Page 14
27
POSEIDON PE/DE
Original Instructions
• Fill with oil.
• Clean.
• Fill the detergent tank.
• Adjust the lance to low
pressure.
• Open fuel cock/fi ll with fuel.
> Low oil level in engine
> Injector is dirty or suction
hose is blocked
> Detergent tank is empty
> The lance is not set to low
pressure
> Low fuel level
The motor stops
When a detergent injector is
used
Fault
Cause
Remedy
8 Further information
8.1 Recycling the pressure
washer
If the pressure washer is
discarded, make it unusable
immediately
1. Dismount the ignition plug.
The pressure washer contains
valuable materials that should
be recycled. Contact your local
waste disposal site. If you have
any queries, please contact
your local authorities or your
nearest dealer.
8.2 Guarantee Your Nilfi sk-ALTO product is
guaranteed for 12 months from
date of purchase (purchase
receipt must be presented) on
the following conditions:
• that defects are attributable
to fl aws or defects in
materials or workmanship.
(Usual wear and tear as well
as misuse are not covered
by the guarantee).
• that repairs have not been
carried out or attempted
by other than Nilfi sk-ALTOtrained service staff.
• that only original
accessories have been
applied.
• that the product has not
been exposed to abuse such
as knocks, bumps or frost.
• that the instructions in the
manual have been carefully
observed.
A warranty repair comprises the
replacement of defective parts,
but it does not cover freight and
packaging charges. Besides we
refer to national Sale of Goods
Act.
Any illegitimate guarantee
repair will be invoiced. (I.e.
malfunctions due to causes
mentioned in section “7
Trouble shooting” of the
instruction manual).
Page 15
28
POSEIDON PE/DE
Original Instructions
8.3 Technical data
POSEIDON
2-31 PE
POSEIDON
3-36 PE
POSEIDON
5-47 PE
POSEIDON
5-53 PE
POSEIDON
5-67 PE
POSEIDON
5-54 DE
Working pressure bar 140 140 190 200 230 195
Water fl ow (max) l/h 700 840 900 1030 1150 1000
Water fl ow Q
IEC l/h 650 750 840 930 1100 950
Max. water inlet temperature °C 60 60 60 60 70 70
Min./max. water inlet pressure bar 1/10 1/10 1/10 1/10 1/10 1
Dimensions (LxWxH) mm 800 x 565 x 1010
Noise power level, LWA dB(A) 93 101 105 104 105 105
Thrust N 24 26 45 46 58 45
Suction height (at max. 8°C) m 1 1.5 0.5 0.5 1 1
Oil quantity in pump/gear l 0.18 0.18 0.32 0.32 0.56/0.27 0.56/0.27
Oil quantity in motor l 0.6 0.6 1.1 1.1 1.1 1.65
Oil type (motor/pump/gear) SAE 15-40
Vibrations < 2,5 m/s
2
We reserve the right to make alterations.
8.4 EC Declaration of Conformity
Declaration of Conformity
Product: High Pressure Washer
Type:
POSEIDON 2-31 PE
POSEIDON 3-36 PE
POSEIDON 5-47 PE
POSEIDON 5-53 PE
POSEIDON 5-67 PE
POSEIDON 5-54 DE
Description: 250 bar / 20 MPa
Petrol driven
Diesel driven
The design of the unit corre sponds to the following pertinent
regulations:
EC Machine Directive 2006/42/EC
EC EMC Directive 2004/108/EC
Applied harmonised standards:
EN 2100-1, EN 12100-2
EN 60335-2-79
EN 55012
Applied national standards and technical specifi cations: DIN EN 60335-2-79
Name and address of the person autho rised to compile the technical
fi le:
Anton Sørensen
General Manager, Technical Operations EAPC
Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Identity and signature of the person empowered to draw up the declaration on behalf of the manufacturer:
Anton Sørensen
General Manager, Technical Operations EAPC
Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Place and date of the declaration Hadsund, March 1, 2012
Page 16
Page 17
HEAD QUARTER
DENMARK
Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Tel.: (+45) 4323 8100
www.nilfi sk-advance.com
SALES COMPANIES
ARGENTINA
Nilfi sk-Advance srl.
Herrera 1855, 6 fl oor, Of. A-604
ZC 1293 – Ciudad Autónoma
de Buenos Aires – Argentina
www.nilfi sk-alto.com
AUSTRALIA
Nilfi sk-ALTO
Unit 1, 13 Bessemer Street Blacktown
NSW 2148 Australia
www.nilfi sk-alto.com.au
AUSTRIA
Nilfi sk-ALTO
Geschäftsbereich der Nilfi sk-Advance GmbH
Metzgerstraße 68
A-5101 Bergheim/Salzburg
www.nilfi sk-alto.at
BELGIUM
Nilfi sk-Advance NV/SA
Riverside Business Park
Boulevard Internationalelaan 55
Bâtiment C3/C4 Gebouw
Bruxelles 1070 Brussel
www.nilfi sk.be
CHILE
Nilfi sk-Advance S.A.
San Alfonso 1462, Santiago
www.nilfi sk.com
CHINA
Nilfi sk-Advance Cleaning Equipment
(Shanghai) Co Ltd.
No. 4189, Yindu Road
Xinzhuang Industrial Park
Shanghai, P.R.C, 201108
www.nilfi sk.cn
CZECH REPUBLIC
Nilfi sk-Advance s.r.o.
Do Certous 1
VGP Park Horní Pocernice, Budova H2
CZ-190 00 Praha 9
www.nilfi sk.cz
DENMARK
Nilfi sk-ALTO Danmark
Industrivej 1
Hadsund, DK-9560
www.nilfi sk-alto.dk
FINLAND
Nilfi sk-Advance OY Ab
Koskelontie 23E
Espoo, FI-02920
www.nilfi sk.fi
FRANCE
Nilfi sk-Advance SAS
Division ALTO
BP 246
91944 Courtaboeuf Cedex
www.alto-fr.com
GERMANY
Nilfi sk-ALTO
Geschäftsbereich der Nilfi sk-Advance AG
Guido-Oberdorfer-Straße 10
89287 Bellenberg
www.nilfi sk-alto.de
GREECE
Nilfi sk-Advance A.E.
8, Thoukididou Str.
Argiroupoli,Athens, GR-164 52
www.nilfi sk.gr
HOLLAND
Nilfi sk-Advance B.V.
Versterkerstraat 5
1322 AN ALMERE
www.nilfi sk.nl
HONG KONG
Nilfi sk-Advance Ltd.
2001 HK Worsted Mills Ind’l Bldg.
31-39 Wo Tong Tsui St.
Hong Kong, Kwai Chung, N.T.
www.nilfi sk.com
HUNGARY
Nilfi sk-Advance Kereskedelmi Kft.
H-2310 Szigetszentmiklós-Lakihegy
II. Rákóczi Ferenc út 10.
www.nilfi sk.hu
INDIA
Nilfi sk-Advance India Limited
Pramukh Plaza, ‘B’ Wing, 4th fl oor, Unit No. 403
Cardinal Gracious Road, Chakala
Andheri (East), Mumbai 400 099
www.nilfi sk.com
IRELAND
Nilfi sk-Advance
1 Stokes Place
St. Stephen’s Green
Dublin 2
www.nilfi sk-alto.ie
ITALY
Nilfi sk-Advance S.p.A.
Strada Comunale Della Braglia, 18
Guardamiglio, Lombardia, I-26862
www.nilfi sk.it
JAPAN
Nilfi sk-Advance Inc.
1-6-6 Kita-Shinyokohama
Kouhoku-Ku
Yokohama 223-0059
www.nilfi sk-advance.co.jp
KOREA
NIlfi sk-Advance Korea
471-4, Kumwon B/D 2F,
Gunja-Dong, Gwangjin-Gu, Seoul
www.nilfi sk-advance.kr
MALAYSIA
Nilfi sk-Advance Sdn Bhd
SD 33, Jalan KIP 10
Taman Perindustrian KIP
Sri Damansara
52200 Kuala Lumpur
Malaysia
www.nilfi sk.com
MEXICO
Nilfi sk Advance de Mexico S. de R.L. de C.V.
Agustin M. Chavez 1, PB-004
Col. Centro Ciudad Santa Fe
C.P. 01210 México, D.F.
www.nilfi sk-advance.com.mx
NEW ZEALAND
Nilfi sk-Advance NZ Ltd
Danish House
6 Rockridge Avenue
Penrose Auckland NZ 1135
www.nilfi sk.com.au
NORWAY
Nilfi sk-Advance AS
Bjørnerudvejen 24
Oslo, N-1266
www.nilfi sk-alto.no
POLAND
Nilfi sk-Advance Sp. z.o.o
Millenium Logistic Park
ul. 3-go Maja 8, Bud. B4
Pruszków, PL-05-800
www.nilfi sk-alto.pl
PORTUGAL
Nilfi sk-Advance, Lda.
Sintra Business Park
Zona Industrial Da Abrunheira
Edifi cio 1, 1o A
Sintra, P-2710-089
www.nilfi sk.pt
RUSSIA
Nilfi sk-Advance LLC
Vyatskaya str. 27, bld. 7, 1st fl oor
Moscow, 127015
www.nilfi sk.ru
SINGAPORE
Nilfi sk-Advance Pte Ltd
22 Tuas Avenue 2
Singapore 639453
www.nilfi sk.com
SPAIN
Nilfi sk-Advance, S.A.
Torre D’Ara
Passeig del Rengle, 5 Plta.10ª
Mataró, E-0830222
www.nilfi sk.es
SWEDEN
Nilfi sk-ALTO
Aminogatan 18
Mölndal, S-431 53
www.nilfi sk-alto.se
SWITZERLAND
NA Sondergger AG
Nilfi sk-ALTO Generalvertretung
Mühlestrasse 10
CH-9100 Herisau
www.nilfi sk-alto.ch
TAIWAN
Nilfi sk-Advance Ltd.
Taiwan Branch (H.K.)
No. 5, Wan Fang Road, Taipei
www.nilfi sk-advance.com.tw
THAILAND
Nilfi sk-Advance Co. Ltd.
89 Soi Chokechai-Ruammitr
Viphavadee-Rangsit Road
Jomphol, Jatuchak
Bangkok 10900
www.nilfi sk.com
TURKEY
Nilfi sk-Advance A.S.
Serifali Mh. Bayraktar Bulv. Sehit Sk. No:7
Ümraniye, Istanbul 34775
www.nilfi sk.com.tr
UNITED KINGDOM
Nilfi sk-ALTO
Bowerbank Way, Gilwilly Industrial Estate
Penrith, Cumbria
GB-CA11 9BQ
www.nilfi sk-alto.co.uk
UNITED ARAB EMIRATES
Nilfi sk-Advance Middle East Branch
SAIF-Zone, P. O. Box 122298
Sharjah
www.nilfi sk.com
USA
Nilfi sk-Advance
14600 21st Ave. North
Plymouth MN 55447-3408
www.nilfi sk-alto.us
VIETNAM
Nilfi sk-Advance Co., Ltd.
No.51 Doc Ngu Str. Lieu Giai Ward
Ba Dinh Dist. Hanoi
www.nilfi sk.com
Loading...