NILFISK CY5000 User Manual
Surface Cleaning with Recovery
CY5000 & CY5500
Pressure Wash Rider with Built-in Recovery and Optional Recycle
•
Instantaneous water recovery
with optional recycle system
•
Chemical free – allows deep
impact cleaning with the use
of only water and heat
•
Aids in EPA compliance with
environmentally friendly
technology
•
Multi-patented Cyclone head
provides easy one-pass cleaning
for increased efficiency
•
Greatly increased productivity
and the ability to drastically
reduce the amount of time
High Pressure Surface Cleaning with Built-in
needed to clean large spaces
Recovery and Optional Recycling.
The revolutionary Cyclone surface-cleaning technology makes it an industry leader for deep
cleaning of concrete and other hard surfaces. The Cyclone scours away dirt, tire marks, and
petroleum deposits without discharge into the environment or damage to the cleaned surface.
The Cyclone cleaning head designed around multi-patented Cyclone technology, provides a
deeper, more consistent cleaning than a spinner head or wand pressure washing. This unique
technology allows for instant water recovery without the use of a vacuum system. With the recycling
option, contaminants are filtered out allowing for the re-use of the reclaimed water for extended
cleaning cycles or meeting specific recycling requirements.
This remarkable self-contained system delivers the most environmentally-friendly, outdoor surface
cleaning solution. Cyclone minimizes water usage, eliminates chemical use and water runoff
and aides in EPA compliance. One-pass cleaning by a single operator dramatically increases
productivity and provides a greater return on investment.
The CY5000 and CY5500 models have a 33 inch (83.8 cm) cleaning path that can clean up to
20,000 square feet (1,858 square meters).
Cyclone technology ™ –
Here’s how it works:
• Cleaning head with 2 high-pressure water nozzles and 8 turbine blades rotates at high speed to
create a vortex of air and water equivalent to a Category 4 hurricane.
• Continuous air movement creates lift that recovers the water along with removed dirt and debris.
• Swirling vortex of air and waste water further scours the surface – resulting in an exceptionally deep
clean with just a single pass.
• The same air movement flings the waste water into a small holding tank, where it is then pumped
into the waste water reclaim tank – thereby completing the waste water recover process
WITHOUT A VACUUM SYSTEM.
• An on-board, multi-stage inline filtration system, standard on the CY5500, cleans and recycles
recovered waste water – extending run-time and further reducing water consumption.
Outdoor surface cleaning will never be the same.
Powerful and consistent cyclone head
delivers efficient, even cleaning.
Before After
Single-pass cleaning to remove ground in
dirt, heavy build up and surface stains
efficiently, without damage to the surface.
Ergonomic, climate controlled, cab design
for operator comfort and ease.
Surface Cleaning with Recovery
CY5000 & CY5500
Cyclone CY5000 & CY5500 Technical Specifications
Model CY5000 CY5500
Operator Cab Style
Cleaning Path 34 in (86 cm) consistently cleaned
Water Pump Triplex plunger capable of 4,000 psi (275 bar) at 5 GPM (19 LPM)
Output Pressure Infinitely variable 1,200 psi (83 bar) – 4,000 psi (275 bar)
Cleaning and Recovery Head Hydraulically powered, cast aluminum 40 in (101.6 cm) diameter with protective shield – Patented Design
Water Heating System
Filtration System None
and two (2) 30 um washable/reusable filter elements,
each with 1,500 in2 of filtration surface area
Water Tanks
Separate recovery tank for waste water that recycles and reuses water in continuous cycle
Easy fill and clean out design Easy fill and clean out design
Cleaning Attachments High pressure curb and gutter cleaning system and high pressure
(Standard) cleaning wand system standard with 25 feet (7.6 m) of hose with reel
Steering Front wheel steering with hydraulic power assist
Drive System Two (2) speed hydrostatic system provides accurate speed control at cleaning speeds with
a maximum transport speed of 11 mph (17.7 kph). Power delivered to front wheels
Controls All cleaning actions controlled from operator seat with ergonomic operator interface
Brakes
Fuel Tank 18 gal (68 L)
Chassis Frame Construction Welded structural steel tubing with 3 in by 2 in tubing with 0.120 in wall thickness
Engine
California code of regulations title 13, section 2423, and EU IIIB directive 1011/88/EU
Sound Level
Without Noise Reduction Kit
With Noise Reduction Kit
Gradeability 20%
Weight Empty: 5,280 lb (2,394 kg) Empty: 5,880 lb (2,667 kg)
Full: 8,282 lb (3,755 kg) Full: 9,132 lb (4,142 kg)
Dimensions (L x W x H) 154 in x 56 in x 77.5 in (3.9 m x 1.4 m x 1.9 m)
Specifications are subject to change without notice.
Rear heavy duty automotive style 11 in hydraulic drum brake with additional hand lever actuated parking brake
Kubota liquid cooled turbo diesel tier 4 emissions that meets US EPA emission standards under 40 CFR 1039.625,
84 dB A
81 dB A
Optional features:
• CY210ConnectionKit
• BackUpCamera
• LaserGuidanceKit
• SpecialOrderColor
Enclosed cab design with heater & air conditioning
Electronically fired, inline diesel powered heater with 240,000 BTU/hr output
Fresh water supply: 360 gal (1,363 L) 390 gal (1,476 L) combination supply and recovery tank
Multi-stage filtration system consisting of two (2) 75 um
Infinitely variable water pressure and
cleaning speed is easily controlled from
the operator’s seat, for a full clean on
various surfaces.
1845 W 1st Street
Phoenix, AZ 85281
800-335-9695 or 480-345-7733
www.advance-cyclone.com
©2012 Nilfisk-Advance, Inc. L3277CT 9-6-12
Optional CY210 Walk-Behind for areas
requiring more maneuverability.
Loading...