Page 1
Nil sk C 120.3
Nil sk C 125.3
Nil sk C 120.5 X-TRA
128330335
User Manual
Page 2
Printed in China
Copyright © 2010 Nilfisk, Division of Nilfisk-Advance A/S
Page 3
Index
1 Safety precautions and warnings .............................................3
2 Description ...............................................................................5
3 Before you start using your pressure washer ...........................6
4 Operating your pressure washer ..............................................7
5 Fields of Application and working methods ..............................9
6 After using your pressure washer ...........................................11
7 Maintenance ...........................................................................13
8 Trouble Shooting ....................................................................15
9 Further information .................................................................16
10 EC Declaration of Conformity .................................................18
1 Safety Precautions and Warnings
Symbols used to mark instructions
Do not let children or people
who have not read the instruction manual ope rate the machine.
This appliance is not intended
for use by children or other
persons without assistance or
supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they do
not play with the appliance.
Before starting up your machine
please check it carefully for any
defects. If you fi nd any, do not
start up your machine and contact your Nilfi sk distributor.
Before starting up
your high-pressure washer for
the fi rst time, this
instruction manual
must be read through carefully.
Save the instructions for later
use.
Safety instructions
marked with this
symbol must be
observed to pre-
vent danger to persons.
Especially check:
The insulation of the electric
cable should be faultless
and without any cracks. If the
electric cable is damaged, an
authorized Nilfi sk distributor
should replace it.
WARNING!
High pressure jets can be
dangerous. Never direct the
water jet at persons, pets,
live electrical equipment or
the machine itself.
Never try to clean clothes or
footwear on yourself or other
persons.
Hold the spray lance fi rmly
with both hands. The spray
lance is affected by a thrust
of up to 16.4 N during ope–
ration.
This symbol is
used to mark safety
instructions that
must be observed
to the machine and its performance.
to simplify work and to ensure a
safe operation.
The operator and anyone in
the immediate vicinity of the
site of cleaning should take
action to protect themselves
from being struck by debris
dislodged during operation.
Wear goggles and protection
clothes during operation.
This appliance has been de-
signed for use with cleaning
agents supplied or recommended by the manufacturer.
The use of other cleaning
agents or chemicals may
adversely affect the safety of
the appliance.
Disconnect from electrical
power supply before carrying
out user maintenance.
To ensure the appliance
safety only use original spare
parts from the manufacturer
to prevent damage
This symbol
indicates tips
and instructions
3
Page 4
or approved by the manufacturer.
High pressure hoses, fi ttings
and couplings are important
for the safety of the appliance. Only use hoses, fi ttings
and couplings recommended
by the manufacturer.
Do not use the appliance
if a supply cord or important parts of appliance are
damaged, e.g. safety device ,
high pressure hose and trigger gun.
The appliance is intended to
clean cars and garden etc..
Appropriate ear protection
has to be used.
Never use the machine in
an environment where there
could be a danger of explosion. If any doubt arises,
please contact the local
authorities.
It is not allowed to clean
asbestos- containing surfaces
with high pressure.
This high pressure washer
must not be used at temperatures below 0°C.
WARNING!
Inadequate extension cables
can be dangerous. Cables on
drums should always be completely unwinded to prevent the
cable from overheating.
Extension cables should be of
a watertight construction and
comply with the below-mentioned requirements for length
and cable dimensions.
1.0 mm² max. 12.5 m
1.5 mm² max. 20 m
2.5 mm² max. 30 m
Cable connections should be
kept dry and off the ground.
If the electric cable is
damaged, it must be replaced by the manufacturer
or his service agent or similarly qualifi ed person in order
to avoid a hazard.
Mains power connection
The following should be observed when connecting the
high pressure washer to the
electric installation:
Only connect the machine to
an installation with earth connection.
The electric installation shall
be made by a certifi ed electrician.
It is strongly recommended
that the electric supply to this
machine should include a residual current device (GFCI).
Water connection
Connection to the public mains
according to regulations.
This high pressure washer is
only allowed to be
connected with
the drinking water
mains, when an appropriate
backfl ow preventer has been
installed, Type BA according
to EN 1717. The backfl ow preventer can be ordered under
number 106411177. The length
of the hose between the backfl ow preventer and the high
pressure washer must be at
least 10 metres to absorb possible pressure peaks (min diameter ½ inch).
Operation by suction (for example from a rainwater vessel)
is carried out without backfl ow
preventer. Recommended suction set: 126411387.
As soon as water has fl own
through the BA valve, this water
is not considered to be drinking
water any more.
IMPORTANT! Only use water without any impurities. If
there is a risk of running sands
in the inlet water (i.e. from your
own well), an additional fi lter
should be mounted.
Repair and maintenance
WARNING! Always remove the
electric plug from the socket before carrying out maintenance
work on the machine.
Safety devices
Locking device on spray gun
(7a) (see foldout at the end of
this manual):
The spray gun features a locking device. When the pawl is
activated, the spray gun cannot
be ope rated.
Thermal sensor:
A thermal sensor protects the
motor against overloading. The
machine will restart after a few
minutes when the thermal sensor has cooled.
Pressure safety device
An integrated hydraulic safety
valve protects the system from
excessive pressure.
4
Page 5
2 Description
2.1 Application This high-pressure washer has
been developed for domestic
use within:
- Car, motorbike, boat, cara-
van, trailer, patio/drive/fl agstones, woodwork, brickwork,
barbecue, garden furniture,
lawn mower
Section 5 describes the use of
2.2 Operation elements
and model survey
See illustration at the end of
this manual.
1 Start/stop switch
2 Water inlet (with fi lter)
3 High pressure connection
4 High pressure hose
5 Electric cable
6 Click & Clean spray lance
7 Spray gun with lock
8 Click & Clean Tornado® PR
nozzle
9 Click & Clean Powerspeed®
nozzle
10 Click & Clean foam sprayer
11 Nozzle cleaning tool
12 Trolley Handle
13 Hose reel (not standard)
14 Hose hook
15 Model tag
16 Warning sign
17 Cable hook
the high-pressure washer for
vaious cleaning jobs.
Only use the high-pressure
washer for purposes described
in this manual.
The safety precautions must be
observed to prevent damage
to the machine, the surface to
be cleaned or severe personal
injuries.
Specifi cations: See model tag
(15) of machine.
Sound pressure level measured
in accordance with ISO 3744,
EEC Directive 2000/14/EEC:
C 120.3/C 125.3:
L
= 78 dB(A), L
pA
= 92 dB(A).
WA
C 120.5 X-TRA:
L
= 71.3 dB(A), L
pA
= 86 dB(A).
WA
Hand/arm vibrations measured
according to ISO 5349 is < 2.5
m/s2.
We reserve the right to alter the
specifi cations.
5
Page 6
3 Before you start using your
pressure washer
3.1 Mounting of trolley
handle and hose hook
3.2 Mounting of trolley handle and hose reel (models
with hose reel)
1. Mount the trolley handle (12)
on the machine.
2. Mount the hose hook (14) on
the handle.
1. Mount the trolley handle (12)
on the machine.
2. Mount the hose reel (13) on
the handle
3.3 Mounting of cable book
(C 120.5 X-TRA)
3.4 Mounting of quick
coupling
Click cable hooks (17) on to the
machine.
1. Screw the quick coupling
tight on to the water inlet (2).
Note: The inlet fi lter
must always be fi t-
ted in the water
inlet pipe to fi lter
these will damage the pump
valves.
Caution: Failure to fi t the fi lter
will invalidate the guarantee.
out sand, lime stone
and other impurities as
6
Page 7
3.5 Mounting of high pressure hose
Attach the high pressure hose
(4) to the spray gun (7).
Detach the high pressure hose
by pressing the pawl (A).
4 Operating your pressure washer
4.1 Connection of high pressure hose
4.2 Mounting of spray
lance and Click & Clean
nozzles
7
1. Push the spray lance (6) into
the spray gun (7) and screw
it on.
6
1. Mount the high pressure
hose on the outlet (3).
Note: The
spray lance (6)
has a built-in low
pressure nozzle that can be
used for fl ushing away dirt.
2. Attach the nozzle.
Warning: When
attaching the Click &
Clean nozzles, the
pawl on the side
of the spray lance
should come out again.
Note: The Tor-
nado® PR nozzle
and the foam
sprayer feature a swivel lock,
which must be positioned in the
hole in the Click & Clean spray
lance.
Press the pawl to detach the
Click & Clean nozzle.
7
Page 8
4.3 Water connection An ordinary 1/2" garden hose of
min. 10 m and max. 25 m will
be suitable.
NOTE: Connection to the public
mains according
to regulations.
IMPORTANT!
Only use water
without any
impurities. If there is a risk
of running sands in the inlet
water (i.e. from your own well),
an additional fi lter should be
mounted.
1. Let the water run through the
water hose before connecting
it to the machine to prevent
sand and dirt from penetrating the machine.
Note: Check that the fi lter is
fi tted in the water inlet pipe
and that it is not clogged up.
2. Connect the water hose to
the water supply by means
of the quick connector (inlet
water, max. pressure: 10 bar,
max. temperature: 40°C).
3. Turn on the water.
4.4 Start and stop of the
machine (when con-
nected to a water supply)
The spray lance is affected
by a thrust during operation therefore always hold it fi rmly
with both hands. IMPORTANT:
Point the nozzle at the
ground.
1. Check that the machine is in
upright position.
NOTE: Do not place the
machine in high grass!
2. Release the trigger lock.
3. Activate the trigger of the
spray gun and let the water
run until all air has escaped
from the water hose.
4. Turn the start/stop switch (1)
to position"I".
5. Activate the trigger of the
spray gun.
Always adjust the distance and
thus the pressure of the nozzle
to the surface, which is to be
cleaned.
Do not cover the machine
during operation.
Note: If the machine is left or not
used for 5 minutes, it must be switched off on
the start/stop switch "O" (1):
1. Turn the start/stop switch (1)
to position"O".
2. Disconnect the electrical plug
from the socket.
3. Shut off the water supply and
activate the trigger to relieve
the machine of pressure.
4. Lock the spray gun.
When releasing the trigger of
the spray gun, the machine
automatically stops. The machine will start again when you
re-activate the spray gun.
8
Page 9
4.5 Start the machine (when
connected to open containers (suction mode))
The washer can take in water
from a rain water tank as an
example. The hose for the water supply must not be too long,
approx. 5 m.
Make sure that the water tank
is not placed on a lower level
than the machine.
1. Place the other end of the
water hose in the water tank.
Use an external fi lter if the
water contains impurities.
2. Turn the start/stop switch (1)
to position"I".
3. Activate the trigger of the
spray gun and let the water
run, until the air has escaped
from the water hose and the
pump.
4. Mount spray lance and
nozzle.
4.6 Pressure regulation on
the TORNADO
nozzle
®
PR-
Lavtryk
Low pressure
High pressure
Højtryk
The pressure can be regulated
on the TORNADO® PR nozzle.
5 Fields of application and working
methods
5.1 General Effi cient high presure cleaning is achieved by following a few guide-
lines, combined with your own personal experience of specifi c
cleaning tasks. Accessories and detergents, when correctly chosen, can increase the effi ciency of your pressure washer. Here is
some basic information about cleaning.
5.1.1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the
chemical product is in direct contact with the dirt. Detergents are
applied from bottom to top, for example on a car bodywork, in order
to avoid "super clean" areas, where the detergent collects in higher
concentration and streams downwards. Let the detergent work for
several minutes before rinsing but never let it dry on the surface being cleaned. Note: It is important that the detergents do not dry up.
Otherwise the surfac that has to be cleaned can be da maged.
5.1.2 Mechanical effect In order to break down tough layers of dirt, additional mechanical
effect may be required. Special wash brushes offer this supplementary effect that cuts through dirt (especially by car washing).
9
Page 10
5.2 Typical fi elds of application
Below you will fi nd a description of a lot of cleaning tasks which can be solved by a pressure washer
from Nilfi sk in association with accessories and detergents.
Task Accessories ‘Click
& Clean’
Car Car nozzle,
auto brush,
underchassis
nozzle,
Foam sprayer,
Car Combi Cleaner
Rims, alu-
minium
Flagstones,
concrete
fl oors and
other hard
surfaces
Garden
furniture,
wood
Brickwork,
Wood work
Gutter Underchassis spray
Cleaning
of drain
pipes, outlets, down
pipes etc.
Rust, paint Water/sandblasting
Green-
house
Garden
tools, lawn
mover
Rim brush,
auto nozzle,
atomizer,
Alu Cleaner
Powerspeed®
nozzle,
Stone & Wood
Cleaner,
Patio Cleaner
Wood Cleaner
Garden brush
Powerspeed®
nozzle,
Stone & Wood
Cleaner,
Patio Cleaner
lance
Tube cleaner Push the tube cleaner approx. ½ m (to mark) into a tube or drain
equipment
Tornado® PR nozzle
brush, Stone &
Wood Cleaner
Tornado® PR noz-
zle, Powerspeed®
nozzle, multiangle
adaptor, Metal
Cleaner
Cleaning method
1. Apply Car Combi Cleaner with the foam sprayer. Always
start from the bottom and work upwards. Let Car Combi
Cleaner act for at least 5 min.
2. Wash the car with the car nozzle, which has been optimized for
quick and gentle cleaning of enamelled surfaces (the jet is wider
and not so sharp). Start at the front of the car and work backwards to avoid water from penetrating by the door mouldings.
3. Use the brush for removal of traffi c fi lm which is not removed by the
nozzle. If the car is very dirty, apply Car Combi Clean er again.
4. Attach the undercarriage nozzle and clean undercarriage and
wheel arches.
5. Remove water from the surface of the car with the scraper
on the car brush. Make sure that all grains of sand etc. have
been removed before using the scraper. Wipe with a wash leather where the scraper cannot reach.
Apply Alu Cleaner with an automizer. Let it act for approx.
5 min. and wash with the rim brush. For steel rims, use Car Combi Cleaner. Use the foam sprayer and wash with rim brush.
Be careful! The high pressure jet may damage the tyres.
Wash towards outlets or the like. On surfaces with moss or
algae you may start by applying Stone & Wood Cleaner with
the foam sprayer. Wash before the soap dries. Another
more effective and quicker method is to use the Patio
Cleaner. Thus you will also avoid splashes.
Apply Wood Cleaner and wash before the soap dries.
NOTE: Use the garden brush to clean off the dirt.
Same method as for fl agstones, but be careful - bad joints and
wood may be damaged by high pressure. You may choose only
to use the Tornado® nozzle. Adjust the distance (pressure) to
the quality of the joints and the wood. Patio Cleaner can also be
used on vertical surfaces.
Wash the gutter with the nozzle. Always wash towards
downpipes. Beware not to spray under the roofi ng.
and activate the trigger of the spray handle. The nozzle opening
turning backwards will pull the cleaner through the tube. The
nozzle will break down the „plug“ and fl ush the dirt backwards.
Mount the water/sand blasting equipment and rust and paint
is effi ciently and quickly removed. Beware not to damage the
surface to be sandblasted.
Wash with high pressure and maybe a brush. You may use Stone
& Wood Cleaner to remove moss and algae.
Rinse the worst dirt off with the nozzle. Apply Metal Cleaner with
the foam sprayer and let it act for approx. 5 min. Wash with the
nozzle. You may use the multiangle adaptor for hard to get at
areas to avoid splashing.
10
Page 11
6 After using your pressure washer
6.1 Storing the washer The machine should be stored in a frost-free room!
Pump, hose and accessories
should always be emptied of
water prior to storing as follows:
6.2 Winding up of electric
cable and high pressure
hose
C 120.3
C 125.3
1. Stop the machine (turn
the start/stop switch (1) to
position"O") and detach water hose and accessory.
2. Restart the machine and
activate the trigger. Let the
machine run until no more
water runs through the spray
gun.
C 120.5 X-TRA
3. Stop the machine, unplug
and wind up hose and cable.
4. Place spray handle, nozzles
and other accessories in the
holders of the machine.
Should the machine by mistake
be frozen, it will be necessary
to check it for damage.
NEVER START-UP A FROZEN
MACHINE.
Frost damages are not
covered by the guarantee!
To avoid accidents, the electric
cable and the high pressure
hose should always be winded
carefully up.
C 120.3
C 125.3
C 120.5 X-TRA
Wind up the electric cable and
the high pressure hose on the
appropriate hooks. Built-in clip
for good holding.
The high pressure washer
comes in two models: A) with
hook for storage of high pressure hose (14) - B) with a hose
reel (13), where the hose is
pushed into the reel and afterwards winded up.
11
Page 12
6.3 Storage of accessories
C 120.3
C 125.3
C 120.5 X-TRA
The standard accessories
(spray gun, spray lance, nozzles and foam sprayer) can be
stored on the pressure washer.
The nozzle cleaning tool can
also be stored on the product.
6.4 Wall storage
A
C
The pressure washer can be
stored on a wall on a special
wall hook (not standard).
B
D
Only mount the wall hook on a
sturdy wall. Adjust the length
of the screws and size of rawlplugs to the type of wall.
On the wall hook garden/rim
brush (a) foam sprayer (b),
Click & Clean brush (c) and
Click & Clean nozzles (d) can
be stored.
Note: For this
product the wall
hook can only be
used as storage.
Important: The
bearing capacity
of the wall hook
is max. 30 kg.
12
Page 13
7 Maintenance
7.1 Cleaning of water inlet
fi lter
WARNING! Always disconnect
the electrical plug from the
socket prior to maintenance or
cleaning.
To ensure a long and problem
free working life, please take
the following advice:
Wash out water hose, high
pressure hose, spray lance
and accessories before
mounting.
Clean the connectors of dust
and sand.
Make sure that no sand or
dirt is blocking the movement
of the pawl on the Click &
Clean spray lance. Rinse according to requirement.
Rinse the detergent spraying
attachment after use.
Clean the nozzles.
Any repair should always be
made in an authorized workshop with original spare parts.
Clean the water inlet fi lter
regularly once a month or more
frequently according to use.
Carefully loosen the fi lter with a
screwdriver and clean it. Check
that it is intact before re-mounting it.
The inlet fi lter must always be
fi tted inside the water inlet pipe
to fi lter out sand, limestone and
other impurities, as they will
damage the pump valves.
CAUTION: Failure to fi t the fi lter
will invalidate the guarantee.
7.2 Cleaning of nozzle A clogging up in the nozzle
causes a pump pressure which
is too high. This is why cleaning
is required immediately.
1. Stop the machine and disconnect the nozzle.
2. Clean the nozzle. IMPOR-
TANT: The cleaning tool (11)
should only be used when
the nozzle is detached!
3. Flush the nozzle backwards
with water.
13
Page 14
7.3 Cleaning of machine
vents
7.4 Greasing of couplings
The machine should be kept
clean so as to let cooling air
pass freely through the machine vents.
To ensure an easy connection and that o-rings do not dry
up, the couplings should be
greased regularly.
14
Page 15
8 Trouble-shooting
To avoid unnecessary disappointments, you should check the following before contacting the Nilfi sk
service organization:
Symptom Cause Recommended action
Machine refuses to start Machine not plugged in Plug in machine.
Defective socket Try another socket.
Fuse has blown Replace fuse. Switch off other machines.
Defective extension cable Try without the extension cable.
Fluctuating pressure Pump sucking air Check that hoses and connections are air-
tight.
Valves dirty, worn out Clean and replace or refer to local Nilfi sk
or stuck distributor
Pump seals worn out Clean and replace or refer to local Nilfi sk
distributor.
Motor busses Low voltage or Activate the trigger of the spray gun.
low temperature
Machine stops Fuse has blown Replace fuse. Switch off other machines.
Incorrect mains voltage Check that the mains voltage corresponds
to specifi cation on the model tag.
Thermal sensor activated Leave the washer for 5 minutes to cool
down.
Nozzle partially blocked Clean the nozzle (see section 7.2)
Fuse blows Fuse too small Change to an installation higher than the
amp. consumption of the machine.
You may try without the extension cable.
Machine pulsating Air in inlet hose/pump Allow machine to run with open trigger until
regular working pressure resumes.
Inadequate supply of Check that the water supply corresponds to
mains water specifi cations required (see model tag)
NB! Avoid using long, thin hoses (min. 1/2")
Nozzle partially blocked Clean the nozzle (see section 7.2)
Water fi lter blocked Clean the fi lter (see section 7.1)
Hose kinked Straighten out hose.
Machine often starts Pump/spray gun is Contact your nearest Nilfi sk Service
and stops by itself leaking Centre.
Machine starts, but Pump/hoses or accessory Wait for pump/hoses or accessory to thaw.
no water comes out frozen
No water supply Connect inlet water.
Water fi lter blocked Clean the fi lter (see section 7.1)
Nozzle blocked Clean the nozzle (see section 7.2)
In case problems other than the above occur, please contact your local Nilfi sk distributor.
UK:
Customer Services at Penrith - 01768 868995
15
Page 16
9 Further information
9.1 Recycling the washer Make the old cleaner unusable
immediately.
1. Unplug the cleaner and cut
the electric cable.
Do not discard electrical appliances with household waste.
9.2 Warranty conditions Nilfi sk guarantees high pressure washers for domestic use
for 2 years. If your high pressure washer or ac ces so ries are
handed in for repair, a copy of
the receipt must be enclosed.
Guarantee repairs are being
made on the following con dit ions:
that defects are attributable
to fl aws or defects in materials or workmanship. (wear
and tear as well as misuse
are not covered by the gu a ran tee).
that the directions of this
instruction manual have been
thoroughly observed.
that repair has not been car-
ried out or attempted by other than Nilfi sk-trained service
staff.
that only original accessories
have been applied.
that the product has not been
exposed to abuse such as
knocks, bumps or frost.
that only water without any
impurities has been used.
that the high pressure wash-
er has not been used for
rental nor used com mer cial ly
in any other way.
As specifi ed in European Directive 2002/96/EC on old electrical and electronic appliances,
used electrical goods must
be collected separately and
recycled ecologically.
Contact your local authorities or
your nearest dealer for further
information.
Repairs under this guarantee
include replacement of defective parts, exclusive of packing
and postage/carriage. Besides,
we refer to your national law of
sale.
The machine should be forwarded to one of the service
centres of the Nilfi sk organisation with description/spe ci fi ca ti on of the fault.
Repairs not covered by the
guarantee conditions will be
invoiced. (I.e. malfunctions due
to Causes men ti o ned in section
Troubleshooting Chart of the
instruction manual).
16
Page 17
9.3 Accessories
Only use original accessories.
Click & Clean
Car nozzle
Click & Clean
Undershassis
nozzle
Click & Clean
Multiangle
adaptor
Click & Clean
Brushes
Extension hose
Underchassis
spray lance
Drain & Tube
cleaner
Special nozzle for enameled surfaces. Optimal distance: 30
- 50 cm.
90° angled special nozzle for undercarriage and wheel arches.
Integrated guide shoes.
Adjusted in angles from 0° - 90° for better working posture and
cleaning of hard to get at places as for instance barrels or the
underside of the lawn mower. Fits all nozzles.
For cars and other surfaces. Available in more shapes.
7 m extension hose increasing the working range.
Special spray lance for washing your car underneath.
15 m long tube cleaner for the cleaning of tubes and drains.
Water-sandblasting equipment
Patio Plus
Garden brush
Rim brush
Wall hook
Rotary brush
For removal of paint and rust. Sand available from do-it-yourself shops.
Equipment for quick cleaning of patio/drive/fl agstones.
Rotary brush for cleaning of wooden surfaces.
Rotary brush for cleaning of wheel rims.
For suspension of your high pressure washer on the wall.
For cleaning vehicles and other surfaces.
Water suction
kit
For removal of large amounts of water from e.g. garden
pounds.
17
Page 18
Detergents
Stone & Wood Cleaner
Plastic Cleaner
Metal Cleaner
Car Combi Cleaner
Alu Cleaner
Oil & Grease Cleaner
For fl agstones, brick- and woodwork. Suitable for moss and algae.
For plastic and synthetic materials such as garden furniture.
For cleaning of metal such as garden tools.
For cars etc. With rinsing wax.
For surfaces of aluminium. Applied with an atomizer.
For cleaning of grease and oil on motors for instance. Applied with
an atomizer.
Wood Cleaner
For cleaning of wooden surfaces incl. of wooden garden furniture.
10 EU Declaration of Conformity
EU Declaration of Conformity
Product:
Type:
Description:
The design of the unit
corre sponds to the following
pertinent regulations:
Applied harmonised standards:
Applied national standards and
technical specifi cations:
Anton Sørensen
General Manager,
Technical Operations EACP
High Pressure Washer
Nilfi sk C 120.3-6, C 125.3-8, C 120.5-6 X-TRA
230 V 1~, 50 Hz - IP X5
EC Machine Directive 2006/42/EC
EC Low-voltage Directive 2006/95/EC
EC EMV Directive 2004/108/EC
EN 60335-2-79
IEC 60335-2-79
Nilfi sk
Division of Nilfi sk-Advance A/S
Industrivej 1
DK-9560 Hadsund
Hadsund, 01.11.2009
18
Page 19
11
Page 20
http://www.nilfi sk-advance.com
HEAD QUARTER
DENMARK
Nilfi sk-Advance Group
Sognevej 25
DK-2605 Brøndby
Tel.: (+45) 4323 8100
E-mail: mail.com@nilfi sk-advance.com
SALES COMPANIES
ARGENTINA
Nilfi sk-Advance srl.
Edifi cio Central Park
Herrera 1855, Offi ce 604
Ciudad Autónoma de Buenos Aires
Tel.: (+54) 11 6091 1571
AUSTRALIA
Nilfi sk-Advance
48 Egerton St.
P.O. Box 6046
Silverwater, N.S.W. 2128
Tel.: +61 2 8748 5900
E-mail: info@nilfi sk-advance.com.au
AUSTRIA
Nilfi sk-Advance GmbH
Metzgerstrasse 68
5101 Bergheim bei Salzburg
Tel.: 0662 456 400-14
E-mail: info.at@nilfi sk-advance.com
BELGIUM
Nilfi sk-Advance n.v-s.a.
Riverside Business Park
Boulevard Internationalelaan 55
Bâtiment C3/C4 Gebouw
Bruxelles 1070
Tel.: (+32) 2 467 60 50
E-mail: info.be@nilfi sk-advance.com
CANADA
Nilfi sk-Advance
240 Superior Boulevard
Mississauga, Ontario L5T 2L2
Tel.: (+1) 905 564 1149
E-mail: info@advance.ca.com
CHILE
Nilfi sk-Advance de Chile
San Alfonso 1462
Santiago
Tel.:(+56) 2 684 5000
E-mail: Pablo.Noriega@nilfi sk-advance.com
CHINA
Nilfi sk-Advance (Suzhou)
Building 18, Suchun Industrial Estate
Suzhou Industrial Park
215021 Suzhou
Tel.: (+86) 512 6265 2525
CZECH REPUBLIC
Nilfi sk-Advance
VGP Park Horní Počernice
Do Čertous 1/2658
193 00 Praha 9
Tel.: (+420) 24 14 08 419
DENMARK
Nilfi sk-Advance A/S
Industrivej 1
9560 Hadsund
Tel.: +45 7218 2100
E-mail: salg.dk@nilfi sk-advance.com
FINLAND
Nilfi sk-Advance Oy Ab
Piispantilankuja 4
02240 Espoo
Tel.: +358 207 890 600
E-mail: asiakaspalvelu.fi @nilfi sk.com
FRANCE
Nilfi sk-Advance
26 Avenue de la Baltique
Villebon sur Yvette
91944 Courtabouef Cedex
Tel.: (+33) 1 69 59 87 00
E-mail: info.fr@nilfi sk-advance.com
GERMANY
Nilfi sk-ALTO
Division of Nilfi sk-Advance AG
Guido-Oberdorfer-Str. 10
89287 Bellenberg
Tel.: (+49) 180 5 37 37 37
E-mail: info.de@nilfi sk-alto.com
GREECE
Nilfi sk-Advance SA
8, Thoukididou str.
164 52 Argiroupolis
Tel.: +30 210 911 9600
E-mail: nilfi sk-advance@clean.gr
HOLLAND
Nilfi sk-Advance
Versterkerstraat 5
1322 AN Almere
Tel.: (+31) 36 546 07 00
E-mail: info.nl@nilfi sk-advance.com
HONG KONG
Nilfi sk-Advance Ltd.
Room 2001 HK Worsted Mills
Industrial Building
31-39 Wo Tong Tsui Street
Kvai Chung
Tel.: (+852) 24 27 59 51
HUNGARY
Nilfi sk-Advance Kereskedelmi Kft.
II. Rákóczi Ferenc út 10
2310 Szigetszentmiklos-Lakihegy
Tel: (+36) 24475 550
E-mail: info@nilfi sk-advance.hu
INDIA
Nilfi sk-Advance India Limited
349, Business Point,
No 201,2nd fl oor, above Popular Car World,
Western Express High way, Andheri ( East),
Mumbai - 400 069
Tel.: (+91) 223 2174592
IRELAND
Nilfi sk-Advance
1 Stokes Place
St. Stephen’s Green
Dublin 2
Tel.: (+35) 3 12 94 38 38
ITALY
Nilfi sk-Advance SpA
Strada Comunale della Braglia, 18
26862 Guardamiglio (LO)
Tel.: +39 0377 41 40 46
E-mail: mercato.italia@nilfi sk-advance.it
JAPAN
Nilfi sk-Advance Inc.
1-6-6 Kita-shinyokohama, Kouhoku-ku
Yokohama, 223-0059
Tel.: (+81) 45 548 2571
KOREA
Nilfi sk-Advance
Kumwon B/D 3F, 471-4, Gunja-Dong
Gwangjin-Ku
Tel.: (+82) 2497 8636
MALAYSIA
Nilfi sk-Advance Sdn Bhd
Sd 14, Jalan KIP 11
Taman Perindustrian KIP
Sri Damansara
52200 Kuala Lumpur
Tel.: (+603) 62753120
MEXICO
Nilfi sk-Advance de Mexico, S. de R.L. de C.V.
Prol. Paseo de la Reforma 61, 6-A2
Col. Paseo de las Lomas
01330 Mexico, D.F.
Tel: +52 55 2591 1002 (switchboard)
E-mail: info@advance-mx.com
NEW ZEALAND
Nilfi sk-Advance
Danish House
6 Rockridge Avenue
Penrose, Auckland 1135
Tel.: (+64) 95 25 00 92
NORWAY
Nilfi sk-Advance AS
Bjørnerudveien 24
1266 Oslo
Tel.: (+47) 22 75 17 70
E-mail: info.no@nilfi sk.com
POLAND
Nilfi sk-Advance Sp. Z.O.O.
05-800 Pruszków
ul. 3-go MAJA 8
Tel.: +48 22 738 37 50
PORTUGAL
Nilfi sk-Advance
Sintra Business Park
Zona Industrial Da Abrunheira
Edifi cio 1, 1° A
P2710-089 Sintra
Tel.: +35 121 911 2670
E-mail: mkt.pt@nilfi sk-advance.com
RUSSIA
Нилфиск-Эдванс
127015 Москва
Вятская ул. 27, стр. 7
Россия
Tel.: (+7) 495 783 96 02
E-mail: info@nilfi sk.ru
SINGAPORE
Nilfi sk-Advance Pte. Ltd.
40 Loyang Drive
Singapore 508961
Tel.: (+65) 6759 9100
SPAIN
Nilfi sk-Advance S.A.
Torre D’Ara
Paseo del Rengle, 5 Pl. 10
08302 Mataró
Tel.: (+3) 4 93 741 2400
E-mail: mkt.es@nilfi sk-dvance.com
SWEDEN
Nilfi sk-Advance
Sjöbjörnsvägen 5
100 73 Stockholm
Tel.: (+46) 85 55 944 00
E-mail: info.se@nilfi sk.com
SWITZERLAND
Nilfi sk-Advance
Ringstrasse 19
Kircheberg/Industri Stelzl
9500 Wil
Tel.: (+41) 719 23 84 44
E-mail: info.ch@nilfi sk-advance.com
TAIWAN
Nilfi sk-Advance Taiwan Branch
1F, No. 193, sec. 2, Xing Long Rd.
Taipei
Tel.: (+88) 6227 002 268
THAILAND
Nilfi sk-Advance Co. Ltd.
89 Soi Chokechai-Ruammitr
Viphavadee-Rangsit Road
Ladyao, Jatuchak, Bangkok 10900
Tel.: (+66) 2 275 5630
TURKEY
Nilfi sk-Advance Profesional Temizlik
Ekipmanlari Tic. A/S.
Necla Cad. No. 48
Yenisahra / Kadiköy
Istanbul
Tel.: (+90) 216 470 08 - 60
E-mail: info.tr@nilfi sk-advance.com
UNITED KINGDOM
Nilfi sk-Advance Ltd.
Unit 24
Hilllside Business Park
Kempson Way
Bury St. Edmunds
Suffolk IP32 7EA
Tel.: (+49) 01284 763163
E-mail: sales.uk@nilfi sk-advance.com
UNITED ARAB EMIRATES
Nilfi sk-Advance Middle East Branch
SAIF-Zone
P.O. Box 122298
Sharjah
Tel.: (+971) 553 2626 82
USA
Nilfi sk-Advance Inc.
14600 21st Avenue North
Plymouth, MN 55447-3408
Tel.: (+1) 763 745 3500
VIETNAM
Nilfi sk-Advance Representative Offi ce
No. 51 Doc Ngu Str.
Ba Dinh Dist.
Hanoi
Tel.: (+04) 761 5642
E-mail: nilfi sk@vnn.vn
Loading...