9 Further information .................................................................15
10 EC Declaration of Conformity .................................................17
1 Safety Precautions and Warnings
Symbols used to mark instructions
Do not let children or people
who have not read the instruction manual ope rate the machine.
Before starting up your machine
please check it carefully for any
defects. If you fi nd any, do not
start up your machine and contact your Nilfi sk distributor.
Especially check:
z The insulation of the electric
cable should be faultless
and without any cracks. If the
electric cable is damaged, an
authorized Nilfi sk distributor
should replace it.
Before starting up
your high-pressure washer for
the fi rst time, this
instruction manual
must be read through carefully.
Save the instructions for later
use.
Safety instructions
marked with this
symbol must be
observed to pre-
vent danger to persons.
WARNING!
z High pressure jets can be
dangerous. Never direct the
water jet at persons, pets,
live electrical equipment or
the machine itself.
z Never try to clean clothes or
footwear on yourself or other
persons.
z Hold the spray lance fi rmly
with both hands. The spray
lance is affected by a thrust
of up to 16.4 N during ope–
ration.
z The operator and anyone in
the immediate vicinity of the
site of cleaning should take
action to protect themselves
from being struck by debris
dislodged during operation.
Wear goggles during operation.
This symbol is
used to mark safety
instructions that
must be observed
,
to the machine and its performance.
to simplify work and to ensure a
safe operation.
z Never use the machine in
an environment where there
could be a danger of explosion. If any doubt arises,
please contact the local
authorities.
z It is not allowed to clean as-
bestos- containing surfaces
with high pressure.
z This high pressure washer
must not be used at temperatures below 0°C.
z Never let any persons stay
under the product when
stored on the wall.
WARNING!
Inadequate extension cables
can be dangerous. Cables on
drums should always be completely unwinded to prevent the
cable from overheating.
to prevent damage
This symbol
indicates tips
and instructions
3
Extension cables should be of
a watertight construction and
comply with the below-mentioned requirements for length
and cable dimensions.
1.0 mm² max. 12.5 m
1.5 mm² max. 20 m
2.5 mm² max. 30 m
z Cable connections should be
kept dry and off the ground.
Mains power connection
The following should be observed when connecting the
high pressure washer to the
electric installation:
z Only connect the machine to
an installation with earth connection.
z The electric installation shall
be made by a certifi ed electrician.
z It is strongly recommended
that the electric supply to this
machine should include a residual current device (GFCI).
Water connection
Connection to
the public mains
according to regulations.
This high pressure washer is only allowed to
be connected with the drinking
water mains, when an appropriate backfl ow preventer has
been installed, Type BA according to EN 1717. The backfl ow
preventer can be ordered under
number 106411177. The length
of the hose between the backfl ow preventer and the high
pressure washer must be at
least 10 metres to absorb possible pressure peaks (min diameter ½ inch).
Operation by suction (for example from a rainwater vessel)
is carried out without backfl ow
preventer. Recommended suction set: 126411387.
As soon as water has fl own
through the BA valve, this water
is not considered to be drinking
water any more.
IMPORTANT! Only use water without any impurities. If
there is a risk of running sands
in the inlet water (i.e. from your
own well), an additional fi lter
should be mounted.
Repair and maintenance
WARNING! Always remove the
electric plug from the socket before carrying out maintenance
work on the machine.
Safety devices
Locking device on spray gun
(7a) (see foldout at the end of
this manual):
The spray gun features a locking device. When the pawl is
activated, the spray gun cannot
be ope rated.
Thermal sensor:
A thermal sensor protects the
motor against overloading. The
machine will restart after a few
minutes when the thermal sensor has cooled.
Pressure safety device
An integrated hydraulic safety
valve protects the system from
excessive pressure.
12 Trolley Handle
13 Hose reel (not standard)
14 Hose hook
15 Model tag
16 Turnable cable hook
Specifi cations: See model tag
(15) of machine.
Sound pressure level measured
in accordance with ISO 3744,
EEC Directive 2000/14/EEC: L
= 71.3 dB(A), L
We reserve the right to alter the
specifi cations.
3 Before you start using your
= 86 dB(A).
WA
pA
pressure washer
3.1 Mounting of trolley
handle and hose hook
3.2 Mounting of hose reel
handle (models with
hose reel)
1. Mount the trolley handle (12)
on the machine. Secure the
handle by tightening the 4
screws.
2. Mount the hose hook (14)
on the machine (2 screws).
Note: the hose hook can be
mounted on the front as well
as on the back. Front position
is to be used if the product is
used together with a special
wall hook for wall storage
(not standard).
1. Click the hose reel handle
on to the trolley handle (no
screws) (not standard).
5
3.3 Mounting of quick
coupling
1. Screw the quick coupling
tight on to the water inlet (2).
Note: The inlet fi lter must always be fi tted in the water inlet
pipe to fi lter out sand, lime stone
and other impurities as these
will damage the pump valves.
Caution: Failure
to fi t the fi lter will
invalidate the
,
guarantee.
3.4 Mounting of high pressure hose
Attach the high pressure hose
(4) to the spray gun (7).
Detach the high pressure hose
by pressing the pawl (A).
4 Operating your pressure washer
4.1 Connection of high pressure hose
1. Mount the high pressure
hose on the outlet (3).
6
4.2 Mounting of spray
lance and Click & Clean
nozzles
7
1. Push the spray lance (6) into
the spray gun (7) and screw
it on.
6
Note: The
spray lance (6)
has a built-in low
pressure nozzle that can be
used for fl ushing away dirt.
2. Attach the nozzle.
Warning: When
attaching the Click
& Clean nozzles,
the pawl on the
,
lance should come out again.
sprayer feature a swivel lock,
which must be positioned in the
hole in the Click & Clean spray
lance.
Press the pawl to detach the
Click & Clean nozzle.
side of the spray
Note: The Tor-
®
nado
zle and the foam
PR noz-
4.3 Water connectionAn ordinary 1/2" garden hose of
min. 10 m and max. 25 m will
be suitable.
NOTE: Connection to the public
mains according
to regulations.
IMPORTANT!
Only use water
without any
impurities. If there is a risk
of running sands in the inlet
water (i.e. from your own well),
an additional fi lter should be
mounted.
1. Let the water run through the
water hose before connecting
it to the machine to prevent
sand and dirt from penetrating the machine.
Note: Check that the fi lter is
fi tted in the water inlet pipe
and that it is not clogged up.
2. Connect the water hose to
the water supply by means
of the quick connector (inlet
water, max. pressure: 10 bar,
max. temperature: 40°C).
3. Turn on the water.
7
4.4 Start and stop of the
machine (when con-
nected to a water supply)
The spray lance is affected
by a thrust during operation therefore always hold it fi rmly
with both hands. IMPORTANT:
Point the nozzle at the
ground.
1. Check that the machine is in
upright position.
NOTE: Do not place the
machine in high grass!
2. Release the trigger lock.
3. Activate the trigger of the
spray gun and let the water
run until all air has escaped
from the water hose.
4. Turn the start/stop switch (1)
to position"I".
5. Activate the trigger of the
spray gun.
Always adjust the distance and
thus the pressure of the nozzle
to the surface, which is to be
cleaned.
Do not cover the machine
during operation.
Note: If the machine is left or not
used for 5 minutes, it must be switched off on
the start/stop switch "O" (1):
1. Turn the start/stop switch (1)
to position"O".
2. Disconnect the electrical plug
from the socket.
3. Shut off the water supply and
activate the trigger to relieve
the machine of pressure.
4. Lock the spray gun.
When releasing the trigger of
the spray gun, the machine
automatically stops. The machine will start again when you
re-activate the spray gun.
4.5 Start the machine (when
connected to open containers (suction mode))
4.6 Pressure regulation on
the TORNADO
®
PR-
nozzle
The washer can take in water
from a rain water tank as an
example. The hose for the water supply must not be too long,
approx. 5 m.
Make sure that the water tank
is not placed on a lower level
than the machine.
High pressure
Højtryk
1. Place the other end of the
water hose in the water tank.
Use an external fi lter if the
water contains impurities.
2. Turn the start/stop switch (1)
to position"I".
3. Activate the trigger of the
spray gun and let the water
run, until the air has escaped
from the water hose and the
pump.
4. Mount spray lance and
nozzle.
The pressure can be regulated
on the TORNADO® PR nozzle.
Lavtryk
Low pressure
8
5 Fields of application and working
methods
5.1 General Effi cient high presure cleaning is achieved by following a few guide-
lines, combined with your own personal experience of specifi c
cleaning tasks. Accessories and detergents, when correctly chosen, can increase the effi ciency of your pressure washer. Here is
some basic information about cleaning.
5.1.1 Detergent and foamFoam or detergent should be applied onto dry surfaces so that the
chemical product is in direct contact with the dirt. Detergents are
applied from bottom to top, for example on a car bodywork, in order
to avoid "super clean" areas, where the detergent collects in higher
concentration and streams downwards. Let the detergent work for
several minutes before rinsing but never let it dry on the surface being cleaned. Note: It is important that the detergents do not dry up.
Otherwise the surfac that has to be cleaned can be da maged.
5.1.2 Mechanical effect In order to break down tough layers of dirt, additional mechanical
effect may be required. Special wash brushes offer this supplementary effect that cuts through dirt (especially by car washing).
9
5.2 Typical fi elds of application
Below you will fi nd a description of a lot of cleaning tasks which can be solved by a pressure washer
from Nilfi sk in association with accessories and detergents.
TaskAccessories ‘Click
Cleaning method
& Clean’
CarCar nozzle,
auto brush,
underchassis
nozzle,
Foam sprayer,
Car Combi Cleaner
1. Apply Car Combi Cleaner with the foam sprayer. Always
start from the bottom and work upwards. Let Car Combi
Cleaner act for at least 5 min.
2. Wash the car with the car nozzle, which has been optimized for
quick and gentle cleaning of enamelled surfaces (the jet is wider
and not so sharp). Start at the front of the car and work backwards to avoid water from penetrating by the door mouldings.
3. Use the brush for removal of traffi c fi lm which is not removed by the
nozzle. If the car is very dirty, apply Car Combi Clean er again.
4. Attach the undercarriage nozzle and clean undercarriage and
wheel arches.
5. Remove water from the surface of the car with the scraper
on the car brush. Make sure that all grains of sand etc. have
been removed before using the scraper. Wipe with a wash leather where the scraper cannot reach.
Rims, alu-
minium
Flagstones,
concrete
fl oors and
other hard
surfaces
Garden
furniture,
Rim brush,
auto nozzle,
atomizer,
Alu Cleaner
Powerspeed
®
nozzle,
Stone & Wood
Cleaner,
Patio Cleaner
Wood Cleaner
Garden brush
Apply Alu Cleaner with an automizer. Let it act for approx.
5 min. and wash with the rim brush. For steel rims, use Car Combi Cleaner. Use the foam sprayer and wash with rim brush.
Be careful! The high pressure jet may damage the tyres.
Wash towards outlets or the like. On surfaces with moss or
algae you may start by applying Stone & Wood Cleaner with
the foam sprayer. Wash before the soap dries. Another
more effective and quicker method is to use the Patio
Cleaner. Thus you will also avoid splashes.
Apply Wood Cleaner and wash before the soap dries.
NOTE: Use the garden brush to clean off the dirt.
wood
Brickwork,
Wood work
Powerspeed
nozzle,
Stone & Wood
Cleaner,
Patio Cleaner
GutterUnderchassis spray
lance
Cleaning
Tube cleanerPush the tube cleaner approx. ½ m (to mark) into a tube or drain
of drain
pipes, outlets, down
®
Same method as for fl agstones, but be careful - bad joints and
wood may be damaged by high pressure. You may choose only
to use the Tornado
®
nozzle. Adjust the distance (pressure) to
the quality of the joints and the wood. Patio Cleaner can also be
used on vertical surfaces.
Wash the gutter with the nozzle. Always wash towards
downpipes. Beware not to spray under the roofi ng.
and activate the trigger of the spray handle. The nozzle opening
turning backwards will pull the cleaner through the tube. The
nozzle will break down the „plug“ and fl ush the dirt backwards.
pipes etc.
Rust, paintWater/sandblasting
equipment
Mount the water/sand blasting equipment and rust and paint
is effi ciently and quickly removed. Beware not to damage the
surface to be sandblasted.
Green-
house
Tornado
brush, Stone &
®
PR nozzle
Wash with high pressure and maybe a brush. You may use Stone
& Wood Cleaner to remove moss and algae.
Wood Cleaner
Garden
tools, lawn
mover
Tornado® PR noz-
zle, Powerspeed
nozzle, multiangle
adaptor, Metal
Rinse the worst dirt off with the nozzle. Apply Metal Cleaner with
®
the foam sprayer and let it act for approx. 5 min. Wash with the
nozzle. You may use the multiangle adaptor for hard to get at
areas to avoid splashing.
Cleaner
10
6 After using your pressure washer
6.1 Storing the washerThe machine should be stored in a frost-free room!
Pump, hose and accessories
should always be emptied of
water prior to storing as follows:
,
6.2 Winding up of electric
cable and high pressure
hose
1. Stop the machine (turn
the start/stop switch (1) to
position"O") and detach water hose and accessory.
2. Restart the machine and
activate the trigger. Let the
machine run until no more
water runs through the spray
gun.
To avoid accidents, the electric
cable and the high pressure
hose should always be winded
3. Stop the machine, unplug
and wind up hose and cable.
4. Place spray handle, nozzles
and other accessories in the
holders of the machine.
Should the machine by mistake
be frozen, it will be necessary
to check it for damage.
NEVER START-UP A FROZEN
MACHINE.
Frost damages are not
covered by the guarantee!
carefully up.
Wind up the electric cable on
the appropriate hooks. Built-in
clip for good holding.
The lower hook can be turned
to release the electric cable.
The high pressure washer
comes in two models: A) with
hook for storage of high pressure hose (14) - B) with a hose
reel (13) , where the hose is
pushed into the reel and afterwards winded up.
11
6.3 Storage of accessories
e
a
The standard accessories
(spray gun and spray lance (a),
d
d
b
nozzles (b) foam sprayer (c))
can be stored on the pressure
washer.
6.4 Wall storage
A
C
b
c
c
b
B
D
The nozzle cleaning tool (d) can
also be stored on the product.
The pressure washer can be
stored on a wall on a special
wall hook (not standard).
Only mount the wall hook on a
sturdy wall. Adjust the length
of the screws and size of rawlplugs to the type of wall.
On the wall hook garden/rim
brush (a) foam sprayer (b),
Click & Clean brush (c) and
Click & Clean nozzles (d) can
be stored.
7 Maintenance
WARNING! Always disconnect
the electrical plug from the
socket prior to maintenance or
cleaning.
To ensure a long and problem
free working life, please take
the following advice:
Note: For this
product the wall
hook can only be
used as storage.
Important: The
bearing capacity
of the wall hook
,
z Wash out water hose, high
pressure hose, spray lance
and accessories before
mounting.
z Clean the connectors of dust
and sand.
is max. 30 kg.
12
z Make sure that no sand or
dirt is blocking the movement
of the pawl on the Click &
Clean spray lance. Rinse according to requirement.
z Rinse the detergent spraying
attachment after use.
z Clean the nozzles.
Any repair should always be
made in an authorized workshop with original spare parts.
7.1 Cleaning of water inlet
fi lter
7.2 Cleaning of nozzle A clogging up in the nozzle
Clean the water inlet fi lter
regularly once a month or more
frequently according to use.
Carefully loosen the fi lter with a
screwdriver and clean it. Check
that it is intact before re-mounting it.
The inlet fi lter must always be
fi tted inside the water inlet pipe
to fi lter out sand, limestone and
other impurities, as they will
damage the pump valves.
CAUTION: Failure to fi t the fi lter
will invalidate the guarantee.
causes a pump pressure which
is too high. This is why cleaning
is required immediately.
1. Stop the machine and disconnect the nozzle.
2. Clean the nozzle. IMPOR-TANT: The cleaning tool (11)
should only be used when
the nozzle is detached!
3. Flush the nozzle backwards
with water.
7.3 Cleaning of machine
vents
7.4 Greasing of couplings
The machine should be kept
clean so as to let cooling air
pass freely through the machine vents.
To ensure an easy connection and that o-rings do not dry
up, the couplings should be
greased regularly.
13
8 Trouble-shooting
To avoid unnecessary disappointments, you should check the following before contacting the Nilfi sk
service organization:
Symptom Cause Recommended action
Machine refuses to start Machine not plugged in Plug in machine.
Defective socket Try another socket.
Fuse has blown Replace fuse. Switch off other machines.
Defective extension cable Try without the extension cable.
Fluctuating pressure Pump sucking air Check that hoses and connections are air-
tight.
Valves dirty, worn out Clean and replace or refer to local Nilfi sk
or stuck distributor
Pump seals worn out Clean and replace or refer to local Nilfi sk
distributor.
Motor bussesLow voltage or Activate the trigger of the spray gun.
low temperature
Machine stopsFuse has blown Replace fuse. Switch off other machines. Incorrect mains voltage Check that the mains voltage corresponds
to specifi cation on the model tag.
Thermal sensor activated Leave the washer for 5 minutes to cool
down.
Nozzle partially blocked Clean the nozzle (see section 7.2)
Fuse blowsFuse too small Change to an installation higher than the amp. consumption of the machine.
You may try without the extension cable.
Machine pulsatingAir in inlet hose/pump Allow machine to run with open trigger until regular working pressure resumes.
Inadequate supply of Check that the water supply corresponds to
mains water specifi cations required (see model tag)
NB! Avoid using long, thin hoses (min. 1/2")
Nozzle partially blocked Clean the nozzle (see section 7.2)
Water fi lter blocked Clean the fi lter (see section 7.1)
Hose kinked Straighten out hose.
Machine often starts Pump/spray gun is Contact your nearest Nilfi sk Service
and stops by itself leaking Centre.
Machine starts, but Pump/hoses or accessory Wait for pump/hoses or accessory to thaw.
no water comes out frozen
No water supply Connect inlet water.
Water fi lter blocked Clean the fi lter (see section 7.1)
Nozzle blocked Clean the nozzle (see section 7.2)
In case problems other than the above occur, please contact your local Nilfi sk distributor.
14
9 Further information
9.1 Recycling the washerMake the old cleaner unusable
immediately.
1. Unplug the cleaner and cut
the electric cable.
Do not discard electrical appliances with household waste.
9.2 Warranty conditionsNilfi sk guarantees high pressure washers for domestic use
for 2 years. If your high pressure washer or ac ces so ries are
handed in for repair, a copy of
the receipt must be enclosed.
Guarantee repairs are being
made on the following con dit ions:
z that defects are attributable
to fl aws or defects in materials or workmanship. (wear
and tear as well as misuse
are not covered by the gu a ran tee).
z that the directions of this
instruction manual have been
thoroughly observed.
z that repair has not been car-
ried out or attempted by other than Nilfi sk-trained service
staff.
z that only original accessories
have been applied.
z that the product has not been
exposed to abuse such as
knocks, bumps or frost.
z that only water without any
impurities has been used.
z that the high pressure wash-
er has not been used for
rental nor used com mer cial ly
in any other way.
As specifi ed in European Directive 2002/96/EC on old electrical and electronic appliances,
used electrical goods must
be collected separately and
recycled ecologically.
Contact your local authorities or
your nearest dealer for further
information.
Repairs under this guarantee
include replacement of defective parts, exclusive of packing
and postage/carriage. Besides,
we refer to your national law of
sale.
The machine should be forwarded to one of the service
centres of the Nilfi sk organisation with description/spe ci fi ca ti on of the fault.
Repairs not covered by the
guarantee conditions will be
invoiced. (I.e. malfunctions due
to Causes men ti o ned in section
Troubleshooting Chart of the
instruction manual).
In order that Nilfi sk can render
you optimum service, you
should register your product on
our web site www.nilfi sk-alto.
com under “PRODUCT REGISTRATION”.
15
9.3 Accessories
Only use original accessories.
Click & Clean
Car nozzle
Click & Clean
Undershassis
nozzle
Click & Clean
Multiangle
adaptor
Click & Clean
Brushes
Extension hose
Underchassis
spray lance
Drain & Tube
cleaner
Special nozzle for enameled surfaces. Optimal distance: 30
- 50 cm.
90° angled special nozzle for undercarriage and wheel arches.
Integrated guide shoes.
Adjusted in angles from 0° - 90° for better working posture and
cleaning of hard to get at places as for instance barrels or the
underside of the lawn mower. Fits all nozzles.
For cars and other surfaces. Available in more shapes.
7 m extension hose increasing the working range.
Special spray lance for washing your car underneath.
15 m long tube cleaner for the cleaning of tubes and drains.
Water-sandblasting equipment
Patio Plus
Garden brush
Rim brush
Wall hook
Rotary brush
For removal of paint and rust. Sand available from do-it-yourself shops.
Equipment for quick cleaning of patio/drive/fl agstones.
Rotary brush for cleaning of wooden surfaces.
Rotary brush for cleaning of wheel rims.
For suspension of your high pressure washer on the wall.
For cleaning vehicles and other surfaces.
Water suction
kit
16
For removal of large amounts of water from e.g. garden
pounds.
Detergents
Stone & Wood Cleaner
Plastic Cleaner
Metal Cleaner
Car Combi Cleaner
Alu Cleaner
Oil & Grease Cleaner
For fl agstones, brick- and woodwork. Suitable for moss and algae.
For plastic and synthetic materials such as garden furniture.
For cleaning of metal such as garden tools.
For cars etc. With rinsing wax.
For surfaces of aluminium. Applied with an atomizer.
For cleaning of grease and oil on motors for instance. Applied with
an atomizer.
Wood Cleaner
For cleaning of wooden surfaces incl. of wooden garden furniture.
10 EU Declaration of Conformity
EU Declaration of Conformity
Product:
Type:
Description:
The design of the unit
corre sponds to the following
pertinent regulations:
Applied harmonised standards:
Applied national standards and
technical specifi cations: