Nilfisk C 120.1 User Manual

Nilfi sk-ALTO C 120.1
08.01.2007
User manual
Printed in China Copyright © 2007 Nilfisk-ALTO
1 Safety precautions and warnings .............................................3
2 Description ...............................................................................4
3 Before you start using your pressure washer ...........................5
4 Operating your pressure washe ...............................................6
5 Fields of Application
and Working Methods ...............................................................8
6 After using your pressure washe ............................................10
7 Maintenance ...........................................................................11
8 Trouble Shooting ....................................................................13
9 Further information .................................................................14
10 EC Declaration of Conformity .................................................16
1 Safety Precautions and Warnings
Symbols used to mark in­structions
Do not let children or people who have not read the instruc­tion manual ope rate the ma­chine.
Before starting up your machine please check it carefully for any defects. If you fi nd any, do not start up your machine and con­tact your ALTO distributor.
Especially check:
z The insulation of the electric
cable should be faultless and without any cracks. If the electric cable is damaged, an authorized Nilfi sk-ALTO dis­tributor should replace it.
Before starting up your high-pres­sure washer for the fi rst time, this
instruction manual must be read through carefully. Save the instructions for later use.
Safety instructions marked with this symbol must be observed to pre-
vent danger to persons.
WARNING!
z High pressure jets can be
dangerous. Never direct the water jet at persons, pets, live electrical equipment or the machine itself.
z Never try to clean clothes or
footwear on yourself or other persons.
z Hold the spray lance fi rmly
with both hands. The spray lance is affected by a thrust of up to 26.5 Nm during ope– ration.
z The operator and anyone in
the immediate vicinity of the site of cleaning should take action to protect themselves from being struck by debris dislodged during operation. Wear goggles during opera­tion.
This symbol is
used to mark safety
instructions that must be observed
,
to the machine and its perform­ance.
to simplify work and to ensure a safe operation.
z Never use the machine in
z It is not allowed to clean as-
z This high pressure washer
z Never let any persons stay
WARNING!
Inadequate extension cables can be dangerous. Cables on drums should always be com­pletely unwinded to prevent the cable from overheating.
to prevent damage
This symbol indicates tips and instructions
an environment where there could be a danger of explo­sion. If any doubt arises, please contact the local authorities.
bestos- containing surfaces with high pressure.
must not be used at tempera­tures below 0°C.
under the product when stored on the wall.
3
Extension cables should be of a watertight construction and comply with the below-men­tioned requirements for length and cable dimensions.
1.0 mm² max. 12.5 m
1.5 mm² max. 20 m
2.5 mm² max. 30 m
z Cable connections should be
kept dry and off the ground.
Mains power connection
z Only connect the machine to
an installation with earth con­nection.
z The electric installation shall
be made by a certifi ed elec­trician.
z It is strongly recommended
that the electric supply to this machine should include a re­sidual current device (GFCI).
Water connection
Connection to the public mains according to regulations.
Repair and maintenance Always remove the electric
plug from the socket before car­rying out maintenance work on the machine.
Safety devices
Locking device on spray gun (7a) (see foldout at the end of
this manual): The spray gun features a lock­ing device. When the pawl is activated, the spray gun cannot be ope rated.
IMPORTANT! Only use wa­ter without any impurities. If
The following should be ob­served when connecting the high pressure washer to the electric installation:
there is a risk of running sands in the inlet water (i.e. from your own well), an additional fi lter should be mounted.
2 Description
2.1 Application This high-pressure washer has
2.2 Operation elements and model survey
4
been developed for domestic use within:
- Car, Motorbike, boat, cara-
van, trailer, patio/drive/fl ags­tones, woodwork, brickwork, barbecue, garden furniture, lawn mower
Section 5 describes the use of
See foldout at the end of this manual.
1 Start/stop switch 2 Water inlet (with fi lter) 3 High pressure connection 4 High pressure hose 5 Electric cable 6 Click & Clean spray lance 7 Spray gun with lock 8 Click & Clean Tornado
nozzle
9 Click & Clean Powerspeed®
nozzle
10 Click & Clean foam sprayer
®
PR
Thermal sensor:
A thermal sensor protects the motor against overloading. The machine will restart after a few minutes when the thermal sen­sor has cooled.
the high-pressure washer for vaious cleaning jobs.
Only use the high-pressure washer for purposes described in this manual.
The safety precautions must be observed to prevent damage to the machine, the surface to be cleaned or severe personal injuries.
11 Nozzle cleaning tool 12 Trolley Handle 13 Hose reel (not standard) 14 Hose hook 15 Model tag
Specifi cations: See model tag (15) of machine.
Sound pressure level measured in accordance with ISO 3744, EEC Directive 2000/14/EEC: L = 71.3 dB(A), L
We reserve the right to alter the specifi cations.
= 86 dB(A).
WA
pA
3 Before you start using your pressure washer
3.1 Mounting of trolley handle (models with trolley handle)
3.2 Mounting of hose reel handle
3.3 Mounting of quick coupling

1. Remove the label on top of machine.
2. Push down the trolley handle

(12) into the machine. Secure the handle by tightening the 2 screws.
3. Mount the hose hook (14) on the handle (3 screws). Note: the hose hook can be mounted on the front as well as on the back. Front position is to be used if the product is used together with a special wall hook for wall storage.
1. Click the hose reel handle on to the trolley handle (no screws).
1. Screw the quick coupling tight on to the water inlet (2).
Note: The inlet fi lter must al­ways be fi tted in the water inlet pipe to fi lter out sand, lime stone and other impurities as these will damage the pump valves.
to fi t the fi lter will
,
Caution: Failure
invalidate the guarantee.
5
3.4 Mounting of high pres­sure hose
Attach the high pressure hose (4) to the spray gun (7).
Detach the high pressure hose by pressing the pawl (A).
4 Operating your pressure washer
4.1 Connection of high pres­sure hose
4.2 Mounting of spray
lance and Click & Clean
nozzles
1. Push the spray lance (6) into the spray gun (7) and screw it on.
1. Mount the high pressure hose on the outlet (3).
Note: The spray lance (6)
pressure nozzle that can be used for fl ushing away dirt.
2. Attach the nozzle.
,
lance should come out again.
sprayer feature a swivel lock, which must be positioned in the hole in the Click & Clean spray lance.
has a built-in low
Warning: When
attaching the Click
& Clean nozzles, the pawl on the
side of the spray
Note: The Tor­nado® PR noz­zle and the foam
Press the pawl to detach the Click & Clean nozzle.
6
Loading...
+ 12 hidden pages