Niles Audio PB6Si User Manual

FEATURES

• Artistically crafted cabinet with shaped

MicroPerf

aluminum grilles look natural

and realistic

• 6.5” dual voice coil injection-molded TCC (talc, carbon, and ceramic) ﬁlled polypropylene woofer with butyl rubber surround

• Dual 1” ﬂuid-cooled tri-laminate Teteron tweeters mounted at a custom angle for optimum dispersion

• Separate left and right channel inputs provide stereo sound in a single loudspeaker projecting quality stereo sound over a larger area than conventional loudspeakers

• Weatherproof design ensures performance outdoors

• Designed to accommodate live plants

• Dual 3-foot burial-rated connection cables with waterproof wire-nuts to insure trouble free connection

• Can be wired in one-speaker stereo-input mode or two-speaker stereo mode

SPECIFICATIONS

Recommended Ampliﬁer Power

10 to 100 Watts

Nominal Impedance

8 Ohm, in one-speaker stereo mode 4 Ohm, in two-speaker stereo mode

Wiring Requirements

2-conductor direct burial cable at the following sizes depending on longest length of cable required (2 per speaker in one-speaker stereo mode):

Wire Gauge Maximum Distance 16 60 ft (18 m) 14 100 ft (30 m) 12 160 ft (50 m)

Temperature Extremes

-50° to 185° Fahrenheit

-45° to 85° Celsius

Shipping Dimensions

12 1/2" high x 28" wide x 11 1/2" deep

Shipping Weight

35 lbs. (15.9 kgs.)

I N S T A L L A T I O N G U I D E

B L E N D I N G H I G H F I D E L I T Y A N D A R C H I T E C T U R E

N i l e s A u d i o C o r p o r a t i o n

1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 1 8 6

3 0 5 - 2 3 8 - 4 3 7 3

1 - 8 0 0 - B U Y - H I F I w w w . n i l e a u d i o . c o m

Bl en di ng H ig h Fi de li ty a nd A rc hi te ct ure a re r eg is te re d tr ad em ar ks o f Ni le s Au dio C or po ra ti on .

Al l ot he r tr ad em ar ks a re t he p ro pe rt y o f th ei r re sp ec ti ve o wn er s. D S 00 62 8A

Figure 1. Stereo Coverage – 4 speakers

FO R USE IN INDOOR O R OUTDO O R MUSIC SYSTEMS

S T E R E O I N P U T P L A N T E R B O X S P E A K E R

PB6Si

sound quality will be poor. will negatively affect sound coverage and produce spots within the listening area where the spacing rules are the recommended maximums; placing speakers at a greater distance apart other. The row spacing between speakers should be less than 38 feet. These loudspeaker speakers can be spaced 11 feet from the sides of the listening area and 22 feet from each gives you the beneﬁt of covering a larger area than the two-speaker stereo mode. The louda separate ampliﬁer channel and each loudspeaker cabinet plays in stereo. This conﬁguration In one-speaker stereo mode, each connection cable of the PB6Si loudspeaker is connected to

SINGLE SPEAKER STEREO MODE

with a 22-foot diameter, in front of the speaker. ing water will shorten the product’s life. The PB6Si loudspeaker will cover an area of a circle aimed on or near the loudspeaker. While the loudspeaker is weatherproof, continuous streamcoverage of the loudspeaker. Never choose a place where an automatic sprinkler will be stereo mode or two-speaker stereo mode, ease of running the cable to the loudspeaker and are three considerations for placing the loudspeaker: connecting each cabinet in one-speaker The PB6Si loudspeaker can be installed on a wood deck or on a concrete/stone patio. There

SELECTING THE NUMBER AND LOCATION FOR YOUR SPEAKERS

• Cable (length and type determined by installation site)

• A wire stripper Tools and Materials Required:

INSTALLATION CONSIDERATIONS

www.nilesaudio.com. accessories for audio/video systems. To see the complete assortment, visit our website at

the highest quality stereo imagining available. With the loudspeakers wired in the one-speaker stereo mode you can cover large areas with

in the one-speaker stereo mode. The loudspeaker coverage pattern is shown in the diagram.

i’s

Figure 1 shows how this would work for a square area of 44 feet by 38 feet and using the PB6S

Niles manufactures the industry’s most complete line of custom installation components and

operation, you’ll enjoy years of trouble free use. Thank you for choosing the PB6Si Planter Speaker from Niles. With proper installation and

CONGRATULATIONS!

ONE-SPEAKER STEREO MODE VS TWO-SPEAKER STEREO MODE

Zone 1

Zone

Zone 1

Zone

Zone 1

Zone

Zone 2

One-speaker stereo mode has the advantage of covering a larger area than the two-speaker stereo mode. The trade off between the two conﬁgurations is volume. The two-speaker stereo conﬁgurations will be able to play louder in its area than the one-speaker stereo conﬁguration.

INCORPORATING A VOLUME CONTROL

It is possible to control the volume of the sound at the speaker location. Volume controls are connected in line with the speaker. An example of wiring an area with 2 speakers and a master volume control is shown in Figure 2 for one-speaker stereo mode, and Figure 3 for two-speaker stereo mode. It is usually desirable to control the volume of the speakers in different areas or zones of the outdoor system. A suggested way to accomplish this is shown in Figure 4 for one- speaker stereo mode, and Figure 5 for two-speaker stereo mode.

Niles recommends our standard weatherproof volume control, WVC100 series or our weatherproof muting volume control, WMVC series. In addition to controlling the volume of the loudspeakers, these controls allow the addition of added speakers without adding more ampliﬁer channels.

INSTALLATION

CONNECTING THE LOUDSPEAKER IN ONE-SPEAKER STEREO MODE

1. Strip two to three inches of each speaker cable’s outer jacket away from the insulated

conductors. Ensure that at least two inches of the separate conductors are free.

2. Strip one half inch of insulation from the end of each conductor for both connection cables.

3. Observe proper phasing when performing the following: Choose the speaker cable that is

labeled for the “Right” ampliﬁer channel. Using a wire nut, connect one stripped end of the “Right” speaker cable to the PB6Si connection cable’s red wire. The wire nut will protect the stripped ends of the wire. If added protection is desired, place a large amount of silicon sealant so the bottom of the wire nut is encased and sealed. Repeat with the PB6Si connection cable’s black wire and the other stripped ampliﬁer “Right” speaker cable’s conductor.

5. Repeat steps 3 and 4 for the “Left” speaker cable and the PB6Si’s connection cable with

the “yellow/black” pair of conductors.

6. Connect the opposite end of the speaker cables to the ampliﬁer or receiver. Start by per-

forming step 1 and 2 on the speaker cable near the ampliﬁer. Use the cable labeled “Right” and attach the same conductor you attached to the red loudspeaker wire to the positive (red) or (+) “Right” ampliﬁer output terminal. Attach the other conductor in that cable to the ampliﬁer’s “Right” negative (black) or (–) ampliﬁer output terminal.

7. Using the cable labeled “Left” attach the same conductor you attached to the yellow loud-

speaker wire to the positive (red) or (+) “Left” ampliﬁer output terminal. Attach the other conductor in that cable to the ampliﬁer’s “Left” negative (black) or (–) ampliﬁer output terminal.

CONNECTING THE LOUDSPEAKER IN TWO-SPEAKER STEREO MODE

1. Strip two to three inches of each speaker cable’s outer jacket away from the insulated conductors. Ensure that at least two inches of the separate conductors are free.

2. Strip one half inch of insulation from the end of each conductor for both connection cables.

3. Connect one stripped end of the speaker cable coming from the ampliﬁer to the PB6Si connection cable’s red wire of one cable and the PB6Si connection cable’s yellow wire. To connect the three wires, twist the stripped ends of the wire together and screw down the wire nut on the twisted wires. The material inside the wire nut will protect the stripped ends of the wire. However, if added protection is desired, place a large amount of silicon sealant so the bottom of the wire nut is encased and sealed. Pay attention to the markings on the speaker cable. Each loudspeaker you connect must be connected to the ampliﬁer’s speaker wire in the same way.

4. Repeat step 3 with the PB6Si connection cable’s black wires and the other stripped ampliﬁer speaker cable’s conductor.

5. Connect the opposite end of the speaker cable to the ampliﬁer or receiver. Start by performing step 1 and 2 on the speaker cable near the ampliﬁer. Paying attention to the markings on the speaker cable conductor, attach the same conductor you attached to the red loudspeaker wire to the positive (red) or (+) ampliﬁer output terminal. Attach the other conductor to the ampliﬁer’s negative (black) or (–) ampliﬁer output terminal.

TROUBLESHOOTING

VERIFY SYSTEM OPERATION AND LOUDSPEAKER COVERAGE

1. Turn the system “On” and play music to the speakers. Set the Volume controls to a level that allows the speakers to be easily heard over the “noise” in the area.

2. Verify that music is playing through each speaker. If not, trouble shoot the wiring and make sure each speaker is electrically connected to the ampliﬁer.

3. Verify that each speaker is connected to the proper channel of the ampliﬁer. To do this, change the balance of your speakers on your ampliﬁer or receiver so that one channel is playing loudly and the other is not. Verify that each speaker or each side of the speaker is attached to the proper channel of the ampliﬁer. If they are not, correct the wiring on the loudspeaker that is not connected properly. Reset the balance on the ampliﬁer or receiver so both channels have a similar volume level.

4. If you used a volume control between the ampliﬁer and the speakers, verify that it is controlling the volume of the loudspeakers in its zone. Repeat this for every volume control in the system. If it is not, correct the wiring.

5. Position the loudspeakers per the layout and verify that the sound is even and consistent throughout the area.

Figure 2. One-speaker stereo, one zone volume control wiring

Figure 3. Two-speaker stereo, one zone volume control wiring

Figure 4. One-speaker stereo, two zone volume control wiring

Figure 5. Two-speaker stereo, two zone volume control wiring