Niles MS-360 user Manual

IR System

Compatible with virtually all brands
of remotes using carrier frequencies
between 20 and 1 10 kHz

IR Receiving Range

25’ to 40’ depending upon the
strength of the remote control

IR Receiving Angle

Omni-directional

Mounting

Ceiling-mount, includes all mount­ing hardware

Wiring Requirements

Individual “home-runs” of
2-conductor shielded cable,
West Penn D291 or equivalent

Unit Dimensions

1/2“ Wide x 2-7/8” Deep
LENS 1-1/2” Diameter x 5/8” High

This manual contains instructions
for the MS360 only. For specific
information on the adjustment
and operation of your Niles
infrared extender system, please
refer to the instruction manual
included with your Niles IR Main
System Unit.

IR Troubleshooting

There are four basic problems
which can prevent proper opera­tion of your MS360 sensor. In the
order of probability, the problems
are as follows:

Bad Connections or Wiring

If the connections or wiring are
wrong, loose, shorted or open, the
system will not operate properly.
The symptoms may include inter­mittent operation or no operation.

1. Test power supply connections.

2. Test your sensor connections.

3. Test your flasher connections.

4. Test your cable for shorts or
opens.

Flasher Level is Too High

Many audio/video components’
sensors are overloaded by receiv­ing too strong of an IR command
from the flasher. Symptoms can
include: popping and clicking
sounds from the speakers when a
button is pressed on the remote
control, poor IR receiving range,
intermittent operation, or no
operation.

1. Connect the flasher(s) to the

variable output of the main sys­tem unit, and reduce the output
level to one half.

2. Move the flasher further away

or off to the side of the sensor
window. Replace the sticky tab on
the flasher and only reapply when
you are sure the new location is
perfect.

Optical or Electromagnetic
Interference

Sunlight, reflections, neon signs
and other sources of electromag­netic fields can induce noise and
interference into your IR extender
system. Common sources of elec­tromagnetic interference may be:
Large direct-view televisions, wall­mounted dimmers/ceiling fan
controls (these devices emit more
interference when turned down
halfway), fluorescent/neon/halo­gen lights, and large appliances.
Symptoms can include poor IR
receiving range, intermittent oper­ation, or no operation. To test the
system for freedom from interfer­ence, carefully observe the IR test
LED on your IR Main System Unit.
If the LED does not flicker, you do
not have interference. If there is
any flickering of the LED, return to
the remote room location and use
tape or paper to entirely cover all
three of the sensing diodes (do
not use your hand—it will disrupt
the test with your body’s magnet­ic field). Return to the IRP unit and
observe the IR LED on the IR Main
System Unit.

If the LED stops flickering you
have optical interference. Install
the sunlight filters over the sens­ing diodes or if the interference is
weak, use the 1/2 strength filters.

If the LED continues to flicker when
the sensing diodes are completely

covered, the interference is not
optical, it is electromagnetic or RF.
Your options are:

1. Ground the MS360’s shield
(the bare wire) to a true earth
ground- preferably as close to the
MS360 as possible.

2. Replace with a Niles MS-1
miniature sensor. This sensor has
two fewer sensing diodes and is
thus 60% less sensitive to EMI.

3. Locate the source of interfer­ence and move it or destroy it.

4. Find a location for the sensor
that is free of interference and
move the sensor, patch the ceiling
and repaint to match the existing
paint.

Optical Feedback Loop

If you have an IR sensor in the
same room as a flasher, and you
have some low-level noise or inter­ference, an optical feedback loop
can occur which will interfere with
normal operation. Symptoms may
include: poor IR receiving range,
intermittent operation, or no
operation.

1. Replace IRC-1 flooding flashers
with IRC-2 stick-on flashers and
cover with the supplied IR block­ing covers.

2. If equipment is housed in cabi­netry, keep the doors closed when
using the IR repeater system.

Contact Niles Technical Support
at 1-800-289-4434 if you require
further assistance.

TROUBLESHOOTING

SPECIFICATIONS

Long Range MicroSensor™
Infrared Extender Circuitry

The Niles MS360 offers revolution­ary real world range because of its
proven MicroSensor circuits. Based
on the acclaimed Niles MS-1 and
MS-2 MicroSensors, the MS360
incorporates cutting edge technolo­gy to optimize range and reliability.
Niles engineers measured perfor­mance in real world conditions
with interference. Backwards com­patible with any Niles IR extender
system, the MS360 offers a new
level of convenience to anyone
using an IR extender system.

Small Size for a Discrete
Installation

The MS360 fits into a 1/2” open­ing in the drywall, and the diame­ter of the entire dome is only one
and one half inches. Additionally,
since all of the interior parts of the
new MS360 are pre-painted white
to blend in, the appearance of the
dome is very discrete.

Three Sensing Diodes Insure
360 Degree Coverage — The
World’s Only Omni-directional
IR Sensor

A conventional infrared sensor
mounted in the ceiling would direct
its cone of sensitivity straight down
— giving you inadequate range
from anywhere in the room except
directly underneath the sensor.
Niles engineers have cleverly com­bined three separate sensing diodes
onto one mounting assembly to
give you enhanced range in all
directions. Advanced electronics
sum the three separate inputs with
incredible reliability and accuracy.

New Total Diode Shielding to
Prevent EMI

Not only is the housing of the
MS360 the same rigid EMI proof
metal cylinder used in the proven
MS-1, but the entire board incor­porating the three sensing diodes
is surrounded with a carefully fit­ted shield.

Filters For Optical
Interference

Each MS360 is supplied with
installer-friendly optical filters
enabling the installer to selectively
filter out sunlight or other types of
optical interference. Since the opti­cal interference may be from only
one direction or from everywhere,
three filters of each type are sup­plied. Full sunlight filters give a
range of twelve feet in direct sun­light. Half sunlight filters prove
useful in bright rooms and typical­ly give more than twenty feet
of range.

Made in the USA

Each MS360 is made with pride in
Miami, Florida USA.

FEATURES & BENEFITS

The MS360 is an omni-direction­al, ceiling-mount infrared sensor
designed for use with the Niles
infrared extender systems.

Installed in a remote room loca­tion, the MS360 receives the IR
commands transmitted from your
hand-held remote(s). The IR com­mands are carried via a small
2-conductor shielded cable to

your A/V equipment in another
room, and instantly "repeated".

The MS360 represents one of the 3
building blocks necessary to com­plete a Niles IR repeating system:

• IR Sensor

s/Keypads—Models
IRR4S+, IRR4D+, MS360, MS-1,
MS-2, TIR1+, RP-6, RP-7, RP-9
and the IntelliPad

®

.

• IR Main System Uni

t

Models IRP2+, IRP6+, IRZ6+,
RVL-6 and MRZ-6.

• IR Flasher

s— Models IRC-1,

IRC-2, and IRC-2P.

An IR sensor expansion unit,
Model XRP6+, is available for IR
repeater systems used in more
than six rooms.

INTRODUCTION

NILES AUDIO CORPORATION 12331 SW 130 STREET MIAMI, FLORIDA 33186 TEL: [phone] FAX: [phone]
WWW.NILESAUDIO.COM © 1999 Niles Audio Corporation. All rights reserved. Because Niles constantly strives to improve the quality of its

products, Niles reserves the right to change product specifications without notice. Niles, the Niles logo, IntelliPad and Blending High Fidelity and
Architecture are registered trademarks of Niles Audio Corporation. MicroSensor is a trademark of Niles Audio Corporation. Printed in USA 8/98
DS00221B

INSTALLATION & OPERATION GUIDE

NILES

B LENDING H IGH F IDELITY

AND

A RCHITECTURE

®

MS360

OMNI-DIRECTIONAL
CEILING-MOUNT
IR SENSOR

®

FM 105.9

Power, IR Data and Ground

via 2-conductor shielded wire

Sensor Location

The MS360 is designed to be ceil­ing mounted in a direct line of
sight location within the operating
range of the remote control.

Using the Optical Interference
Filters

As with any type of IR sensor,
avoid locating the MS360 where it
will be exposed to direct sunlight
or very bright artificial light.
Although the MS360 can be fil­tered to work even in direct sun­light, the range of operation will
be severely reduced.

There are two filter strengths. The
white self-adhesive paper squares
are sunlight filters which enables the
MS360 to function reliably in direct
sunlight with limited range (typical­ly less than 12 feet). The beige self­adhesive paper squares can be used
when the optical interference is not
as bright as direct sunlight. The
beige squares give more range
(typically about 20 feet).

Sometimes you need only filter
one or two sides of the sensor,
allowing you full range in the other
unfiltered direction.

Type of Cable

The MS360 connects to the Niles
IR main system unit with an indi­vidual “home run” (wired directly)
of 2-conductor shielded cable.
Recommended cables are West
Penn D291, Belden 8761, Carol
C2516 or equivalent that is made
of two 22 gauge (or larger) con­ductors surrounded by a foil shield
and a bare drain (ground) wire.

DO NOT USE UNSHIELDED
CABLE WITH THE MS360.

INSTALLATION CONSIDERATIONS

SYSTEM CONNECTIONS

INSTALLATION

Step by Step

1. The MS360 requires a 1/2” cir­cular opening for installation. Use
a hole saw suitable for the mount­ing surface being cut. The hole
can be cut during construction or
after. The overall depth of the
MS360 is 2 7/8”, so if it is
installed in 1/2” drywall it will
extend 1 3/4” behind the ceiling.

2. Run the cable to the MS360.
Label the cable for future refer­ence. See (Figure 2).

3. Make the connections to the
MS360. Strip 1/4" of insulation
from the end of each wire. Tightly
twist the end of each wire until
there are no frayed ends. Match
the Red to the Red, the Bare to
the Bare and the Black to the
Black. Solder or use wire nuts to
connect the flying leads coming
out of the MS360.

4. Insert the barrel housing of
the MS360 into the hole in the
ceiling. Use the two self-threading
1” screws to attach the sensor to
the ceiling.

5. Connect the IR Data cable to
the IR Main System Unit’s sensor
connections. Power up the Main
System Unit.

6. Test the system for freedom
from interference by observing
the IR test LED on your Main
System Unit.

If the LED does not flicker go to
Step 7. If there is any flickering of
the LED, go to TroubleShooting
section under Optical or Electro­magnetic Interference.

7. Install the dome onto the
base of the MS360, observing
the notch in the base and the
corresponding ridge in the plas­tic dome. Lock the dome into
place by rotating it in a clock­wise direction until the dome is
firmly attached.

+

12
V

FLASHERS

FULL VAR

DATA

OUT

SENSOR INPUTS

G
N
D

D
A
T
A

+

12
V

G
N
D

D
A
T
A

G
N
D

D
A
T
A

+-+

-

MODEL

IRP2

+

FLASHER

LEVEL

IR

+

12V DC

POWER STATUS

Figure 1: Connecting the MS360 to a Niles IRP2+ IR Main System Unit.

12V DC Power Supply

(supplied with the IRP2+

IR Main System Unit)

plugged into an unswitched

AC outlet powers the system

Niles IR Flasher

IRP2+ IR Main System Unit

Stereo Receiver

GND
Bare

DATA

Black

+12V

Red

Figure 2

Wiring connections for the MS360.

Operation of the MS360 is simple.
Stand within the operational
range of your MS360. Aim your
hand-held remote at the MS360

and initiate the desired command.
Your IR command is instantly
repeated to your A/V equipment.

OPERATION

Figure 3

Installation Features of

the MS360

1/2” Diameter Barrel slips

through hole in ceiling

1” Self-tapping

screws mount the

MS360 to the

ceiling.

1” Self-tapping

screws mount the

MS360 to the

ceiling.

Translucent Dome

locks onto the base

plate.

Shielding surrounds
the three IR sensing

diodes.

NILES