The following are important notes about the camera's waterproofing. Before using the
camera, please thoroughly read the information in “<Important> Shockproof, Waterproof,
Dustproof, Condensation” (A xv).
Waterproofing-related Messages
The camera will display messages related to its waterproof capabilities when you select
certain settings or perform certain operations. Read and follow the information displayed in
the messages when they are displayed.
Do not open the covers by
the water or in sandy
locations, as foreign matter
could enter the camera.
Remove any foreign matter
with a brush or blower.
Conrm that no foreign
matter is present where
shown, then close the covers.
To remove foreign matter
after use, immerse in fresh
water for about 10 minutes.
Next, wipe o any water
droplets and place on a cloth
to dry.
After drying thoroughly, use
a cloth to remove any
droplets remaining on the
areas indicated.
Waterproofing-related messages are displayed in the following situations.
• When turning on and setting the camera for the first time
• When setting the camera to Shoot under water (A 39)
• When turning the camera on after charging
Note: If the cover is closed without removing foreign particles, water may seep inside the
camera or the camera may become damaged. Make sure to inspect and clean the cover.
Introduction
Parts of the Camera
The Basics of Shooting and Playback
Shooting Features
Playback Features
Recording and Playing Back Movies
General Camera Setup
Connecting the Camera to a TV, Computer, or Printer
Reference Section
Technical Notes and Index
i
Introduction
Read This First
Introduction
Thank you for purchasing the Nikon COOLPIX S32 digital camera. Before using the camera,
please read the information in “For Your Safety” (A viii-xi) and “<Important> Shockproof,
Waterproof, Dustproof, Condensation“ (A xv-xxi), and familiarize yourself with the
information provided in this manual. After reading, please keep this manual handy and refer
to it to enhance your enjoyment of your new camera.
ii
About This Manual
If you want to start using the camera right away, see “The Basics of Shooting and Playback”
(A 8).
To learn about the parts of the camera and basic operations, see “Parts of the Camera” (A 1).
Introduction
iii
Other Information
• Symbols and Conventions
To make it easier to find the information you need, the following symbols and conventions
are used in this manual:
Introduction
IconDescription
B
C
A/E/F
This icon indicates cautions and information that should be read before using
the camera.
This icon indicates notes and information that should be read before using the
camera.
These icons indicate other pages containing relevant information;
E: “Reference Section”, F: “Technical Notes and Index.”
• SD, SDHC, and SDXC memory cards are referred to as “memory cards” in this manual.
• The setting at the time of purchase is referred to as the “default setting.”
• The names of menu items displayed in the camera monitor, and the names of buttons or
messages displayed on a computer monitor appear in bold.
• In this manual, images are sometimes omitted from monitor display samples so that
monitor indicators can be more clearly shown.
• Illustrations and monitor content shown in this manual may differ from the actual product.
iv
Information and Precautions
Holographic seal: Identifies this
device as an authentic Nikon product.
Life-Long Learning
As part of Nikon’s “Life-Long Learning” commitment to ongoing product support and education,
continually updated information is available online at the following sites:
• For users in the U.S.A.: http://www.nikonusa.com/
• For users in Europe and Africa: http://www.europe-nikon.com/support/
• For users in Asia, Oceania, and the Middle East: http://www.nikon-asia.com/
Visit these sites to keep up-to-date with the latest product information, tips, answers to frequently
asked questions (FAQs), and general advice on digital imaging and photography. Additional
information may be available from the Nikon representative in your area. Visit the site below for
contact information:
http://imaging.nikon.com/
Use Only Nikon Brand Electronic Accessories
Nikon COOLPIX cameras are designed to the highest standards and include complex electronic
circuitry. Only Nikon brand electronic accessories (including battery chargers, batteries, Charging AC
adapters, and AC adapters) certified by Nikon specifically for use with this Nikon digital camera are
engineered and proven to operate within the operational and safety requirements of this electronic
circuitry.
THE USE OF NON-NIKON ELECTRONIC ACCESSORIES COULD DAMAGE THE CAMERA AND MAY VOID
YOUR NIKON WARRANTY.
The use of third-party rechargeable Li-ion batteries not bearing the Nikon holographic seal could
interfere with normal operation of the camera or result in the batteries overheating, igniting,
rupturing, or leaking.
For more information about Nikon brand accessories, contact a local authorized Nikon dealer.
Before Taking Important Pictures
Before taking pictures on important occasions (such as at weddings or before taking the camera on
a trip), take a test shot to ensure that the camera is functioning normally. Nikon will not be held liable
for damages or lost profits that may result from product malfunction.
Introduction
v
About the Manuals
• No part of the manuals included with this product may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language in any form, by any means, without
Nikon’s prior written permission.
• Nikon reserves the right to change the specifications of the hardware and software described in
Introduction
these manuals at any time and without prior notice.
• Nikon will not be held liable for any damages resulting from the use of this product.
• While every effort was made to ensure that the information in these manuals is accurate and
complete, we would appreciate it were you to bring any errors or omissions to the attention of the
Nikon representative in your area (address provided separately).
Notice Concerning Prohibition of Copying or Reproduction
Note that simply being in possession of material that was digitally copied or reproduced by means
of a scanner, digital camera or other device may be punishable by law.
• Items prohibited by law from being copied or reproduced
Do not copy or reproduce paper money, coins, securities, government bonds or local government
bonds, even if such copies or reproductions are stamped “Sample.” The copying or reproduction of
paper money, coins, or securities which are circulated in a foreign country is prohibited. Unless the
prior permission of the government was obtained, the copying or reproduction of unused postage
stamps or post cards issued by the government is prohibited.
The copying or reproduction of stamps issued by the government and of certified documents
stipulated by law is prohibited.
• Cautions on certain copies and reproductions
The government has issued cautions on copies or reproductions of securities issued by private
companies (shares, bills, checks, gift certificates, etc.), commuter passes, or coupon tickets, except
when a minimum of necessary copies are to be provided for business use by a company. Also, do
not copy or reproduce passports issued by the government, licenses issued by public agencies and
private groups, ID cards and tickets, such as passes and meal coupons.
• Comply with copyright notices
The copying or reproduction of copyrighted creative works such as books, music, paintings,
woodcut prints, maps, drawings, mov ies, and photographs is governed by national and international
copyright laws. Do not use this product for the purpose of making illegal copies or to infringe
copyright laws.
vi
Disposing of Data Storage Devices
Please note that deleting images or formatting data storage devices such as memory cards or
built-in camera memory does not completely erase the original image data. Deleted files can
sometimes be recovered from discarded storage devices using commercially available software,
potentially resulting in the malicious use of personal image data. Ensuring the privacy of such data is
the user’s responsibility.
Before discarding a data storage device or transferring ownership to another person, erase all data
using commercial deletion software, or format the device and then completely refill it with images
containing no private information (for example, pictures of empty sky). Care should be taken to
avoid injury or damage to property when physically destroying data storage devices.
Introduction
vii
For Your Safety
To prevent damage to your Nikon product or injury to yourself or to others, read
the following safety precautions in their entirety before using this equipment.
Introduction
Keep these safety instructions where all those who use the product will read them.
This icon marks warnings, information that should be read before using this Nikon
product, to prevent possible injury.
WARNINGS
Turn off in the event of
malfunction
Should you notice smoke or an unusual
smell coming from the camera or
Charging AC Adapter, unplug the
Charging AC Adapter and remove the
battery immediately, taking care to
avoid burns. Continued operation
could result in injury. After removing or
disconnecting the power source, take
the equipment to a Nikon-authorized
service representative for inspection.
Do not disassemble
Touching the internal parts of the
camera or Charging AC Adapter could
result in injury. Repairs should be
performed only by qualified
viii
technicians. Should the camera or
Charging AC Adapter break open as
the result of a fall or other accident,
take the product to a Nikon-authorized
service representative for inspection,
after unplugging the product and/or
removing the battery.
Do not use the camera or
Charging AC Adapter in the
presence of flammable gas
Do not use electronic equipment in
the presence of flammable gas, as this
could result in explosion or fire.
Handle the camera strap with
care
Never place the strap around the neck
of an infant or child.
Keep out of reach of children
Particular care should be taken to
prevent infants from putting the
battery, brush, or other small parts into
their mouths.
Do not remain in contact with
the camera, Charging AC
Adapter, or AC adapter for
extended periods while the
devices are on or in use
Parts of the devices become hot.
Leaving the devices in direct contact
with the skin for extended periods may
result in low-temperature burns.
Do not leave the product
where it will be exposed to
extremely high temperatures,
such as in an enclosed
automobile or in direct
sunlight
Failure to observe this precaution
could cause damage or fire.
Observe caution when
handling the battery
The battery may leak, overheat, or
explode if improperly handled.
Observe the following precautions
when handling the battery for use in
this product:
• Before replacing the battery, turn
the product off. If you are using the
Charging AC Adapter/AC adapter,
be sure it is unplugged.
• Use only a Rechargeable Li-ion
Battery EN-EL19 (included). Charge
the battery by using a camera that
supports battery charging or by
using a Battery Charger MH-66
(available separately). To charge the
battery with the camera, use either
Charging AC Adapter EH-70P
(included) or the Charge by computer function.
• When inserting the battery, do not
attempt to insert it upside down or
backwards.
• Do not short or disassemble the
battery or attempt to remove or
break battery insulation or casing.
• Do not expose the battery to flame
or to excessive heat.
Introduction
ix
• Do not immerse in or expose to
water.
• Put the battery in a plastic bag
before transporting it. Do not
transport or store with metal objects
Introduction
such as necklaces or hairpins.
• The battery is prone to leakage
when fully discharged. To avoid
damage to the product, be sure to
remove the battery when no charge
remains.
• Discontinue use immediately should
you notice any change in the
battery, such as discoloration or
deformation.
• If liquid from the damaged battery
comes in contact with clothing or
skin, rinse immediately with plenty
of water.
Observe the following
precautions when handling
the Charging AC Adapter
• Keep dry. Failure to observe this
precaution could result in fire or
electric shock.
• Dust on or near the metal parts of
the plug should be removed with a
dry cloth. Continued use could
result in fire.
• Do not handle the plug or go near
the Charging AC Adapter during
lightning storms. Failure to observe
this precaution could result in
electric shock.
• Do not damage, modify, forcibly tug
or bend the USB cable, place it
under heavy objects, or expose it to
heat or flames. Should the insulation
be damaged and the wires become
exposed, take it to a Nikonauthorized service representative for
inspection. Failure to observe these
precautions could result in fire or
electric shock.
• Do not handle the plug or Charging
AC Adapter with wet hands. Failure
to observe this precaution could
result in electric shock.
• Do not use with travel converters or
adapters designed to convert from
one voltage to another or with DCto-AC inverters. Failure to observe
this precaution could damage the
product or result in overheating or
fire.
x
Use appropriate cables
When connecting cables to the input
and output jacks, use only the cables
provided or sold by Nikon for the
purpose, to maintain compliance with
product regulations.
Handle moving parts with care
Be careful that your fingers or other
objects are not pinched by the lens
cover or other moving parts.
Observe caution when using
the flash
Using the flash close to your subject’s
eyes could cause temporary visual
impairment. The flash should be no
less than 1 m (3 ft 4 in.) from the
subject. Particular care should be
observed when photographing
infants.
Do not operate the flash with
the flash window touching a
person or object
Failure to observe this precaution
could result in burns or fire.
Avoid contact with liquid
crystal
Should the monitor break, care should
be taken to avoid injury caused by
broken glass and to prevent liquid
crystal from the monitor touching the
skin or entering the eyes or mouth.
Turn the power off when
using inside an airplane or the
hospital
Turn the power off while inside the
airplane during take off or landing.
Follow the instructions of the hospital
when using while in a hospital.
The electromagnetic waves emitted by
this camera may disrupt the electronic
systems of the airplane or the
instruments of the hospital.
Introduction
xi
Notices
Notice for Customers in the
U.S.A.
Introduction
IMPORTANT SAFETY
INSTRUCTIONS -
SAVE THESE INSTRUCTIONS.
DANGER - TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, CAREFULLY
FOLLOW THESE INSTRUCTIONS
For connection to a supply not in the
U.S.A., use an attachment plug adapter
of the proper configuration for the
power outlet if needed.The power
supply unit is intended to be correctly
orientated in a vertical or floor mount
position.
Federal Communications
Commission (FCC) Radio
Frequency Interference
Statement
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
xii
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment
off and on, the user is encouraged to try
to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an
experienced radio/television
technician for help.
CAUTIONS
Modifications
The FCC requires the user to be
notified that any changes or
modifications made to this device that
are not expressly approved by Nikon
Corporation may void the user’s
authority to operate the equipment.
Interface Cables
Use the interface cables sold or
provided by Nikon for your equipment.
Using other interface cables may
exceed the limits of Class B Part 15 of
the FCC rules.
Notice for customers in the State of
California
WARNING
Handling the cord on this product will
expose you to lead, a chemical known
to the State of California to cause birth
defects or other reproductive harm.
Wash hands after handling.
Nikon Inc.,
1300 Walt Whitman Road Melville,
New York 11747-3064 USA
Tel: 631-547-4200
Notice for customers in Canada
CAN ICES-3 B / NMB-3 B
Notice for Customers in Europe
CAUTIONS
RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
This symbol indicates that
electrical and electronic
equipment is to be collected
separately.
The following apply only to
users in European countries:
• This product is designated for
separate collection at an
appropriate collection point. Do not
dispose of as household waste.
• Separate collection and recycling
helps conserve natural resources
and prevent negative consequences
for human health and the
environment that might result from
incorrect disposal.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
Introduction
xiii
This symbol on the battery
indicates that the battery is
to be collected separately.
The following apply only to
users in European countries:
Introduction
• All batteries, whether marked with
this symbol or not, are designated
for separate collection at an
appropriate collection point. Do not
dispose of as household waste.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
• Make sure to read the following instructions as well as the instructions provided in “Caring
for the Product” (F2).
Notes About Shockproof Performance
This camera has passed Nikon’s in-house test (drop test from a height of 1.5 m (5 ft) on a 5 cm
(2 in.) thick plywood panel) compliant with MIL-STD 810F Method 516.5-Shock*.
This test does not guarantee the waterproof performance of the camera or that the camera
will be free from damage or trouble under all conditions.
Changes in appearance, such as paint peeling off and deformation of the drop shock portion
are not subject to the Nikon’s in-house test.
* U.S. Department of Defense test method standard.
This drop test drops 5 cameras in 26 directions (8 edges, 12 corners, and 6 faces) from a height of
122 cm (48 in.) to make sure that one to five camera s pass the test (if any defect is detected during
the test, another five cameras are tested to make sure that the test criteria are satisfied for one to
five cameras).
bDo not subject the camera to excessive shock, vibration or pressure by dropping
or hitting it.
Failure to observe this precaution could cause water to seep inside the camera and result in
camera malfunction.
• Do not use the camera deeper than 10 m (33 ft) underwater.
• Do not subject the camera to water pressure by exposing it to high-pressure running
water.
• Do not sit down with the camera in the pocket of your trousers.
Do not forcibly stuff the camera into a bag.
Introduction
xv
Notes About Waterproof and Dustproof Performances
The camera is equivalent to IEC/JIS waterproof grade 8 (IPX8) and IEC/JIS dustproof grade 6
(IP6X) and enables shooting pictures underwater at a depth of 10 m (33 ft) for up to 60
minutes.*
This rating does not guarantee the waterproof performance of the camera or that the camera
Introduction
will be free from damage or trouble under all conditions.
* This rating indicates that the camera has been designe d to withstand the specified water pressure
for the specified period of time when the camera is used according to the methods defined by
Nikon.
bIf the camera is subjected to excessive shock, vibration or pressure by dropping
or hitting it, the waterproof performance is not guaranteed.
• If the camera is exposed to shocks, it is recommended to consult your retailer or Nikonauthorized service representative to confirm the waterproof performance (charged service).
- Do not use the camera deeper than 10 m (33 ft) underwater.
- Do not subject the camera to water pressure by exposing it to rapid flowing water or
waterfalls.
- Your Nikon warrantee may not cover troubles caused by water seeping inside the
camera due to improper handling of the camera.
• The waterproof performance of this camera is designed to work for fresh water and
seawater only.
• The inner portion of this camera is not waterproof. Water seeping inside the camera could
cause a malfunction.
• Accessories are not waterproof.
• If liquids or water droplets come into contact with the outside of the camera or the inside
of the battery-chamber/memory card slot cover, immediately wipe the liquids off with a
soft dry cloth. Do not insert wet memory cards or the battery.
If the battery-chamber/memory card slot cover is opened or closed under wet conditions
near a waterfront or underwater, this could cause water to seep inside the camera or result
in camera malfunction.
Do not open or close the cover with wet hands. This could cause water to seep inside the
camera or result in camera malfunction.
xvi
• If a foreign substance adheres to the outside of the
camera or the inside of the battery-chamber/memory
card slot cover (such as the hinge, memory card slot, and
connectors), remove it immediately with a blower. If a
foreign substance adheres to the waterproof packing
inside the battery-chamber/memory card slot cover,
remove it with the included brush. Do not use the
included brush for anything other than cleaning the
waterproof packing.
• If a foreign substance such as suntan oil, sunscreen lotion, hot spring, bath mix powder,
detergent, soap, organic solvent, oil, or alcohol adheres to the camera, immediately wipe it
off.
• Do not leave the camera in high-temperature conditions of 40°C (104°F) or more (in
particular, a place exposed to direct sunlight, inside the cabin of a car, on a boat, on the
beach, or near a heating device) for a long period of time. This could cause deterioration of
the waterproof performance.
Before Using the Camera Underwater
1. Make sure that there are no foreign substances inside the battery-chamber/
memory card slot cover.
• Any foreign substances such as sand, dust or hair inside the battery-chamber/memory
card slot cover should be removed with a blower.
• Any liquid such as water droplets inside the battery-chamber/memory card slot cover
should be wiped off with a soft dry cloth.
2. Make sure that the waterproof packing (A 2) of the battery-chamber/memory
card slot cover is not cracked or deformed.
• The waterproof performance of waterproof packing may start to deteriorate after one
year.
If the waterproof packing begins to deteriorate, consult your retailer or Nikonauthorized service representative.
3. Make sure that the battery-chamber/memory card slot cover is firmly closed.
• Slide the cover until it clicks into place.
Introduction
xvii
Notes About Using the Camera Underwater
Observe the following precautions to prevent water from seeping inside the
camera.
• Do not dive into water deeper than 10 m (33 ft) with the camera.
• Do not continuously use the camera underwater for 60 minutes or more.
Introduction
• Use the camera in the water temperature range 0°C–40°C (32°F–104°F) when using it
underwater.
Do not use the camera at hot springs.
• Do not open or close the battery-chamber/memory card slot cover underwater.
• Do not subject the camera to shock when using it underwater.
Do not jump into water with the camera or subject it to high water pressure conditions
such as rapids or waterfalls.
• This camera does not float in water. Make sure not to drop the camera underwater.
Cleaning After Using the Camera Underwater
• After using the camera underwater, clean the camera within 60 minutes. If you leave the
camera in wet conditions where salt particles or other foreign substances adhere to it, this
could cause damage, discoloration, corrosion, a bad smell or deterioration of waterproof
performance.
• Before cleaning the camera, thoroughly remove water droplets, sand, salt particles, or
other foreign substances from your hands, body, and hair.
• It is recommended to clean the camera indoors to avoid a place where it could be exposed
to water spray or sand.
• Do not open the battery-chamber/memory card slot cover until all foreign substances are
washed off with water and all moisture is wiped off.
xviii
1. Keep the battery-chamber/memory card slot cover closed and wash off the
camera with fresh water.
Lightly rinse the camera with tap water, or immerse the camera in a shallow basin filled
with freshwater for about 10 minutes.
• If the buttons or switches do not operate properly, foreign substances may have
adhered to the camera.
Foreign substances can cause the camera to malfunction; wash the camera thoroughly.
2. Wipe off water droplets with a soft cloth and dry the camera in the well-ventilated
and shady place.
• Place the camera on a dry cloth to dry it.
Water will flow out from openings in the microphone or speakers.
• Do not dry the camera with hot air from a hair dryer or clothes dryer.
• Do not use chemicals (such as benzine, thinner, alcohol, or cleanser), soap, or neutral
detergents.
If the waterproof packing or body of the camera becomes deformed, the waterproof
performance will deteriorate.
Introduction
xix
3. After making sure that there are no water droplets on the camera, open the
battery-chamber/memory card slot cover, gently wipe off any water remaining
inside the camera with a dry soft cloth, and use the blower to remove any foreign
substances.
• If you open the cover before the camera is thoroughly dried, water droplets may fall on
Introduction
the memory card or battery.
The water droplets may also seep inside the battery-chamber/memory card slot cover
(in locations such as waterproof packing, hinges, memory card slot, or terminals).
If that happens, wipe the water off with a dry soft cloth.
• If the cover is closed when the inside is wet, this could cause condensation or
malfunction.
• If the microphone or speaker openings are clogged with water droplets, the sound may
deteriorate or become distorted.
- Wipe the water off with a dry soft cloth.
- Do not puncture the microphone or speaker openings with a sharp implement. If the
inside of the camera is damaged, the waterproof performance will deteriorate.
xx
Notes About Operating Temperature and Humidity and
Condensation
The operation of this camera has been tested at temperatures –10°C – +40°C (14°F–104°F).
When you use the camera in cold climate regions, observe the following precautions. Keep
the camera and spare batteries in a warm place before use.
• The performance of the batteries (number of pictures shot and shooting time) will drop
temporarily.
• If the camera is in a very cold state, the performance may drop temporarily, for example,
the monitor may be darker than normal immediately after the camera is turned on or
residual images may be produced.
• When snow or water droplets adhere to the exterior of the camera, immediately wipe
them off.
- If the buttons or switches are frozen, they may not operate smoothly.
- If the microphone or speaker openings are clogged with water droplets, the sound may
deteriorate or become distorted.
bOperating environmental conditions such as temperature
and humidity may cause fogging (condensation) on the
inside of the monitor, lens, or flash window.
This is not a camera malfunction or defect.
bEnvironmental conditions that are likely to cause
condensation inside of the camera
Fogging (condensation) may occur on the inside of the monitor, lens, or flash window in the
following environmental conditions where there are sharp temperature changes or high humidity.
•
The camera is suddenly immersed in low temperature underwater from high temperature on land.
• The camera is moved from a cold place to a warm place, such as inside a building.
•
The battery-chamber/memory card slot cover is open or closed in a high-humidity environment.
bClearing the fogging
• Open the battery-chamber/memory card slot cover after turning off the camera in a place
where the ambient temperature is stable (avoid any place that has high temperature/high
humidity, sand or dust).
To clear the fogging, remove the battery and memory card, and leave the camera with the
battery-chamber/memory card slot cover open to allow the camera to adjust to the
ambient temperature.
• If the fogging does not clear, consult your retailer or Nikon-authorized service representative.
Introduction
xxi
Table of Contents
Introduction ................................................... ii
Read This First ....................................................... ii
Introduction
About This Manual .................................................. iii
Information and Precautions ............................. v
For Your Safety ................................................. viii
WARNINGS ................................................................ viii
Notices................................................................... xii
<Important> Shockproof, Waterproof,
Dustproof, Condensation ............................... xv
Notes About Shockproof Performance..... xv
Notes About Waterproof and Dustproof
Performances........................................................... xvi
Before Using the Camera Underwater.... xvii
Notes About Using the Camera
Underwater............................................................. xviii
Cleaning After Using the Camera
Underwater............................................................. xviii
Notes About Operating Temperature and
Humidity and Condensation ......................... xxi
Parts of the Camera ..................................... 1
The Camera Body................................................. 1
Attaching the Camera Strap............................... 3
The Monitor ........................................................... 4
16 Grade mark ............................................ 58, E16
15:30
15
9999
999
65
999
1416
1324
15/05/2014
29m 0s
29m 0s
7
8
9
10
11
Parts of the Camera
12
13
C If Information Is Not Displayed During Shooting Mode and Playback Mode
Apart from certain information, information is not displayed if no operations are performed for
several seconds. Information is displayed again when either a flexible button or the multi selector is
pressed.
5
Using the Flexible Buttons
11 0 0
20 m 0s
4
15 / 0 5/ 2 01 4
15 : 3 0
Shooting mode
Playback mode
Flexible button 1
Flexible button 2
Flexible button 3
Flexible button 4
Flexible button 1
Flexible button 2
Flexible button 3
Flexible button 4
If you press a flexible button while the shooting screen or playback screen is displayed, the
menu for the current mode is displayed. Once the menu is displayed, you can change various
settings.
In this document, the flexible buttons are referred to as “flexible button 1” through “flexible
button 4”, in order from top to bottom.
Parts of the Camera
6
15/05/2014
15:30
1100
20m 0s
4
Selecting Items
Flash
Flash mode/self-timer
Self-timer
Exchange messages
Have fun with pictures
Picture play
Grading
Shooting modePlayback mode
Use HI to display other
pages.
To select an item, press the
flexible button next to the
item.
The last setting selected
(including the default
setting) is displayed in
white.
• To select an item, press the flexible button next to it.
• When Q is displayed, press flexible button 1 to return to the previous screen.
• When the menu content continues on another page, a guide indicating the page position
is displayed.
Press the multi selector HI to display other pages.
Parts of the Camera
Camera settings
Welcome screen
Date and time
Brightness
C Notes About Setting Menu Options
Some menu options cannot be selected depending on how the camera is set up. These options are
displayed in gray.
Camera settings
Print date
Electronic VR
AF assist
Print date
Date
O
7
The Basics of Shooting and Playback
Battery latch
Preparation 1 Insert the Battery
1 Open the battery-chamber/memory card slot
cover.
The Basics of Shooting and Playback
2 Insert the battery.
• Push the orange battery latch in the direction indicated by
the arrow (1), and fully insert the battery (2).
• The battery locks into place when inserted correctly.
B Be Careful to Insert the Battery in Correct
Direction
Inserting the battery upside down or backwards could
damage the camera.
8
3 Close the battery-chamber/memory card slot
cover.
• Lay the cover completely flat in the direction indicated by
the arrow (1), and fully slide it in (2).
B Damage Caution
Sliding the cover while it is open may damage the
camera.
Removing the Battery
Turn the camera off and make sure that the power-on lamp
and the monitor have turned off, and then open the batterychamber/memory card slot cover.
Move the battery latch in the direction indicated by the arrow
(1) to eject the battery (2).
B High Temperature Caution
The camera, battery, and memory card may be hot immediately after using the camera.
B Opening and Closing the Battery-chamber/Memory Card Slot Cover
Do not open and close the battery chamber/memory card slot cover in a sandy or dusty
environment or with wet hands. If the cover is closed without removing foreign particles, water may
seep inside the camera or the camera may become damaged.
• If foreign particles get inside the cover or camera, immediately remove them with a blower or
brush.
• If liquid such as water gets inside the cover or camera, immediately wipe it off with a soft and dry
cloth.
The Basics of Shooting and Playback
9
Preparation 2 Charge the Battery
1
3
2
Charge lamp
USB cable (included)
Electrical outlet
1 Turn off the camera and open the battery-chamber/
memory card slot cover.
2 Prepare the included Charging AC Adapter.
The Basics of Shooting and Playback
If a plug adapter* is included with your camera, attach the plug adapter to the
plug on the Charging AC Adapter. Push the plug adapter firmly until it is
securely held in place. Once the two are connected, attempting to forcibly
remove the plug adapter could damage the product.
* The shape of the plug adapter varies according to the country or region in
which the camera was purchased.
The Charging AC Adapter comes with the plug adapter attached in
Argentina and Korea.
3 Make sure the battery is installed in the camera, and then connect the
camera to the Charging AC Adapter in order of 1 to 3.
• Keep the camera turned off.
• Make sure that the plugs are properly oriented. Do not insert or remove the plugs at an
angle when connecting or disconnecting them.
10
• The charge lamp slowly flashes green to indicate that the battery is charging.
• Shooting is not possible while the camera is connected to the Charging AC Adapter.
Charge lampDescription
Flashes slowly (green) The battery is charging.
When charging is complete, the charge lamp stops flashing green and
Off
Flashes quickly
(green)
turns off.
About 2 hours and 35 minutes are required to charge a fully exhausted
battery.
• The ambient temperature is not suited to ch arging. Charge the battery
indoors with an ambient temperature of 5°C to 35°C (41°F to 95°F).
• The USB cable or Charging AC Adapter is not properly connected, or
there is a problem with the battery. Disconnect the USB cable or
unplug the Charging AC Adapter and correctly connect it again, or
change the battery.
4 Disconnect the Charging AC Adapter from the electrical outlet and
then disconnect the USB cable.
C Charging Using a Computer or Battery Charger
• You can also charge the battery by connecting the camera to a computer (A 67, E43).
• You can use the Battery Charger MH-66 (available separately; E59) to charge the battery without
using the camera.
The Basics of Shooting and Playback
11
Preparation 3 Insert a Memory Card
Memory card slot
1 Turn off the camera and open the battery-
chamber/memory card slot cover.
The Basics of Shooting and Playback
2 Insert the memory card.
• Slide the memory card in until it clicks into place.
B Be Careful to Insert the Memory Card in
Correct Direction
Inserting the memory card upside down or backwards
could damage the camera and the memory card.
12
3 Close the battery-chamber/memory card slot
cover.
• Lay the cover completely flat in the direction indicated by
the arrow (1), and fully slide it in (2).
B Damage Caution
Sliding the cover while it is open may damage the
camera.
B Formatting Memory Cards
The first time you insert a memory card that has been used in another device into this camera, make
sure to format it with this camera. Inse rt the card into the camera and select Format card in the
camera settings menu.
Removing Memory Cards
Turn the camera off and make sure that the power-on lamp
and the monitor have turned off, and then open the batterychamber/memory card slot cover.
Gently push the memory card into the camera (1) to partially
eject the card (2).
B High Temperature Caution
The camera, battery, and memory card may be hot immediately after using the camera.
Internal Memory and Memory Cards
Camera data, including images and movies, can be saved either in the camera’s internal
memory or on a memory card. To use the camera’s internal memory, first remove the memory
card.
The Basics of Shooting and Playback
13
Preparation 4 Setting the Display Language, Date, and Time
When the camera is turned on for the first time, the language-selection screen, the date and
time setting screen for the camera clock, and the menu background setting screen are
displayed.
• If you exit without setting the date and time, O will flash when the shooting screen is
displayed.
1 Press the power switch to turn on the camera.
The Basics of Shooting and Playback
2 Use the multi selector JK to select
the desired language and press
flexible button 4 (O).
3 Press flexible button 3 (R Yes).
14
Language
Set time and date?
Yes
No
4 Use flexible button 2, 3, or 4 to select
Year/Month/Day
Date format
Month/Day/Year
Day/Month/Year
the date format.
• Select d Year/Month/Day, e Month/
Day/Year, or f Day/Month/Year.
5 Set the date and time, and press
flexible button 4 (O).
• Select a field: Press JK (changes between D, M,
Y, h, and m).
• Edit the date and time: Press HI.
• Apply the setting: Select m and press flexible
button 4 (O).
• To enable daylight saving time, press flexible
button 3 (m). When the daylight saving time function is enabled, m is displayed in the
monitor. To turn off the daylight saving time function, press flexible button 3 (m) again.
Date and time
6 Press flexible button 3 (R Yes).
Yes
No
YD
Mhm
/
05
16 30
201415
/
:
15/05/2014 15:30
OK?
The Basics of Shooting and Playback
15
7 Use JK to select the background
Menu background
Do not open the covers by
the water or in sandy
locations, as foreign matter
could enter the camera.
image to be displayed when a menu
or setting screen is displayed, and
press flexible button 4 (O).
• To restore the default background image, press
flexible button 3 (P).
8 Confirm the waterproofing-related message
The Basics of Shooting and Playback
and press K.
• There are six message screens.
9 Confirm the message on the screen
shown at right and press flexible
button 4 (O).
• The monitor changes to the shooting screen
(A 18).
16
After drying thoroughly, use
a cloth to remove any
droplets remaining on the
areas indicated.
C Changing the Language Setting, the Date and Time Setting, and the Menu
Background Setting
• You can change the Language, Date and time, and Menu background settings in the
l camera settings menu (A 65).
• You can enable or disable daylight saving time in the l camera settings menu by selecting Date
and time. When enabled, the clock moves forward one hour; when disabled, the clock moves
back one hour.
C The Clock Battery
• The camera’s clock is powered by a built-in backup battery. The backup battery charges when the
main battery is inserted into the camera or when the camera is connected to an optional AC
adapter, and it can run the clock for several days after about ten hours of charging.
• If the camera’s backup battery becomes exhausted, the date and time setting screen is displayed
when the camera is turned on. Set the date and time again. ➝ Step 3 of “Preparation 4 Setting the
Display Language, Date, and Time” (A 14)
C Imprinting the Shooting Date on Printed Images
• You can permanently imprint the shooting date on images as they are captured by setting Print
date in the camera settings menu (A 65).
• If you want the shooting date to be printed without using the Print date setting, print using the
ViewNX 2 software (A 69).
The Basics of Shooting and Playback
17
Step 1 Turn the Camera On
1 10 0
2 0m 0s
Battery level indicator
Number of exposures
remaining
1 Press the power switch.
• The monitor turns on.
• To turn the camera off, press the power switch again.
2 Check the battery level indicator and the
The Basics of Shooting and Playback
number of exposures remaining.
Battery level indicator
DisplayDescription
FThe battery level is high.
GThe battery level is low.
Battery
exhausted.
Number of Exposures Remaining
The number of images that can be taken is displayed.
• C is di splayed when no memory card is i nserted in the camera , and imag es are save d in the
internal memory.
The camera cannot capture images.
Recharge the battery.
1100
20m0s
18
C The Auto Off Function
110 0
20m 0s
Flashes
No operations
performed
No operations
performed
3 min
Camera enters
standby mode.
Camera turns off.
1100
20m 0s
• The time that elapses before the camera enters standby mode is about three minutes.
• While the camera is in standby mode, the monitor turns back on if you perform any of the
following operations:
➝ Press the power switch, shutter-release button, c (shooting/playback mode) button, or
b (e movie-record) button
The Basics of Shooting and Playback
19
Step 2 Frame a Picture
1 10 0
20m 0 s
1 Hold the camera steady.
• Keep fingers and other objects away from the lens, flash,
AF-assist illuminator, microphone, and speaker.
The Basics of Shooting and Playback
2 Frame the picture.
C When Using a Tripod
We recommend using a tripod to stabilize the camera in the following situations.
• When shooting in dim lighting
• When shooting with the flash mode (A 31) set to y Flash off
• When using the telephoto setting
20
1100
20m 0s
Using the Zoom
Zoom out
Zoom in
1 10 0
20m 0 s
Zoom indicator
Maximum
optical zoom
Digital zoom
enabled
Optical
zoom
Digital
zoom
When you press the multi selector HI, the zoom lens
position changes.
• To zoom in closer to the subject: Press H (telephoto)
• To zoom out and view a larger area: Press I (wide-angle)
When you turn the camera on, the zoom moves to the
maximum wide-angle position.
• A zoom indicator is displayed in the monitor when the multi
selector HI is pressed.
• If you press H when the camera is zoomed
in to the maximum optical zoom position,
you can use the digital zoom to magnify the
image further by up to about 4×.
1100
20m 0s
The Basics of Shooting and Playback
C Digital Zoom and Interpolation
While using digital zoom, the image quality decreases due to interpolation depending on the image
size and the amount of digital zoom magnification.
When using digital zoom, we recommend reducing the image size in A Photo size under C Choose a size in order to minimize image deterioration (A 49).
21
Step 3 Focus and Shoot
1 /2 5 01/250 F 3.3F3.3
1 Press the shutter-release button halfway.
• When the subject is in focus, the focus area glows green
(multiple focus areas can glow green).
• When you are using digital zoom, the camera focuses on
the subject in the center of the frame and the focus area is
not displayed. When the camera has focused, the focus
indicator (A 4) glows green.
The Basics of Shooting and Playback
• If the focus area or focus indicator flashes, the camera is
unable to focus. Modify the composition and try pressing
the shutter-release button halfway again.
2 Without lifting your finger, press the shutter-
release button the rest of the way down.
22
The Shutter-release Button
To set focus and exposure (shutter speed and aperture value),
Press halfway
Press all the way
press the shutter-release button lightly until you feel a slight
resistance. Focus and exposure remain locked while the shutterrelease button is pressed halfway.
Press the shutter-release button all the way to release the shutter
and take an image.
Do not use force when pressing the shutter-release button, as this
may result in camera shake and blurred images. Press the button
gently.
B Notes About Saving Images and Recording Movies
The indicator showing the number of exposures remaining or the indicator showing the maximum
movie length flashes while images are being saved or while a movie is being recorded. Do not open the battery-chamber/memory card slot cover or remove the battery or memory card while an
indicator is flashing. Doing this could result in loss of data, or in damage to the camera or the
memory card.
The Basics of Shooting and Playback
23
Step 4 Play Back Images
c
(shooting/
playback mode)
button
Display
the
previous
image
Display
the
next
image
4
1 5/ 0 5/ 2 0 14
1 5: 3 0
1 Press the c (shooting/playback mode)
button.
• If you press and hold down the c (shooting/playback
mode) button while the camera is turned off, the camera
turns on in playback mode.
The Basics of Shooting and Playback
2 Use the multi selector to select an image to
display.
• Press and hold down JK to scroll through the images
quickly.
24
• To return to shooting mode, press the c (shooting/
playback mode) button or shutter-release button.
15/05/2014
15:30
4
Step 5 Delete Images
4
15 / 0 5/ 2 01 4
15 : 3 0
1 Display the image you want to delete
in the monitor and then press flexible
button 3 (n).
2 Use flexible button 2, 3, or 4 to select
the deletion method.
• Select n Erase this picture only, o Erase
selected pictures (A 26), or k Erase all
pictures.
• To exit without deleting, press flexible button 1
(Q).
3 Press flexible button 3 (R Yes).
• Deleted images cannot be recovered.
• To exit without deleting, press flexible button 4
(SNo).
15/05/2014
15:30
4
Erase
Erase this picture only
Erase selected pictures
Erase all pictures
Erase 1 picture ?
Yes
No
The Basics of Shooting and Playback
25
Selecting Which Images You Want to Delete
1 Use the multi selector JK to select an
image to be deleted, and then press
flexible button 2 (S).
• The selected image is indicated by a check mark.
• A check mark is displayed or removed e very time
you press flexible button 2 (S).
• Press flexible button 3 (P) to remove all
The Basics of Shooting and Playback
26
check marks.
2 Add check marks to all images that you want to delete and press
flexible button 4 (O) to confirm the selection.
• A confirmation dialog is displayed. Follow the instructions displayed in the monitor.
Erase selected pictures
Restrict Image Deletion (Image Lock)
44
1 5/ 0 5/ 2 0 1415/05/2014 1 5 :3 015:30
4
1 5/ 0 5/ 2 0 14
1 5: 3 0
To prevent accidental deletion of images, you can lock image deletion (A 25) and
formatting (A 65, E40).
1 Press and hold down flexible buttons
1 and 4 at the same time while in
shooting mode or playback mode.
2 Press flexible button 3 (R Yes).
• Image lock is set.
Yes
No
• When image lock is set, C is displayed in the
monitor.
Removing Image Lock
The procedure for removing image lock is the same as for setting image lock.
Enable image lock?
15/05/2014
15:30
The Basics of Shooting and Playback
4
27
Shooting Features
Functions Available in Shooting Mode (Shooting Menu)
Press a flexible button to display a menu. You can change the following settings.
Flexible buttonOptionDescriptionA
A Point and
shoot
Shooting Features
Z Flash mode/
self-timer
g More picture
options
28
–Sets the shooting mode to A Point and shoot.30
FlashAllows you to set the flash mode.31
The camera is equipped with a self-timer that
Self-timer
Choose a style
Decorate
Change colors
releases the shutter about ten seconds after you
press the shutter-release button. You can also set
the smile timer.
Allows you to select the scene settings and effects
used for shooting.
Allows you to add a frame around your images
when taking images.
Allows you to select b Brighter/darker or
c More vivid/less vivid from the menu, or use
P Highlight colors to keep one specified color
in the image, and change the other colors to
black and white.
33, 35
37
43
44
Flexible buttonOptionDescriptionA
l Settings
Change sounds
Choose a size
Camera settings
Allows you to configure the shutter and button
sounds.
Allows you to set the size of photos (still images)
and movies.
Allows you to change a number of general
settings.
47
49
65
Shooting Features
29
A Point and Shoot
When this camera is used for the first time, the shooting mode is set to A Point and shoot.
The camera automatically selects the optimum scene when you frame an image, making it
even easier to take images using settings that suit the scene.
A Point and shoot is the default shooting mode for this camera.
• The area of the frame that the camera focuses on varies depending on the composition of
the image.
• When the camera detects a human face, it focuses on that face (A 53). The skin softening
feature makes the skin tones in human faces appear smoother (A 54).
• The flash may fire when shooting in low light.
• When shooting in low light, the use of a tripod is recommended.
• The camera does not detect the scene when the digital zoom is being used.
Shooting Features
C Notes About Motion Detection
In A Point and shoot and Shoot close-ups (A 38), when the camera detects subject movement
or camera shake, ISO sensitivity and shutter speed are increased to reduce blurring.
30
Using the Flash
You can select the flash mode to match the shooting conditions.
Enter shooting mode M flexible button 2 (Z) M flexible button 2 (x Flash)
Available Flash Modes
Auto flash
w
The flash fires when necessary, such as in dim lighting.
Flash off
y
The flash does not fire.
• We recommend using a tripod to stabilize the camera when shooting in dark
surroundings.
xAlways fire flash
The flash fires whenever an image is tak en. Use to “fill-in” (illuminate) shadows and backlit
subjects.
Shooting Features
Use flexible button 2, 3, or 4 to select the
flash mode.
• Select w Auto flash, y Flash off, or x Always
fire flash.
• To cancel, press flexible button 1 (Q).
Flash
Auto ash
Flash o
Always re ash
31
C The Flash Lamp
The status of the flash can be confirmed by pressing the shutter-release
button halfway.
• On: The flash fires when you press the shutter-release button all the
way down.
• Flashing: The flash is charging. The camera cannot shoot images.
• Off: The flash does not fire when an image is taken.
If the battery level is low, the monitor turns off while the flash is charging.
C The Flash Mode Setting
• The setting may not be changed when using some shooting modes or settings.
• The setting applied in A Point and shoot is saved in the camera’s memory even after the camera
Shooting Features
is turned off.
32
Using the Self-timer
10 s
Self-timer
Smile timer
O
1 /2 5 01/250 F 3.3F3.31 010
The camera is equipped with a self-timer that releases the shutter about ten seconds after
you press the shutter-release button.
Enter shooting mode M flexible button 2 (Z) M flexible button 3 (i Self-timer)
1 Press flexible button 2 (j 10 s).
• When Y Smile timer is selected, the camera
uses face detection to detect a human face, and
then automatically releases the shutter when a
smile is detected (A 35).
2 Frame the picture and press the
shutter-release button halfway.
• Focus and exposure are set.
Shooting Features
33
3 Press the shutter-release button the
1 /2 5 0
F 3.3
rest of the way down.
• Countdown starts. The self-timer lamp flashes
and then glows steadily about one second
before the shutter is released.
• When the shutter is released, the self-timer is set
to b Off.
• To stop the countdown, press the shutterrelease button again.
Shooting Features
1/250
F3.399
34
Using the Smile Timer
When the camera detects a smiling face, you can take an image automatically without
pressing the shutter-release button. The skin softening function makes the skin tones of
human faces smoother.
Enter shooting mode M flexible button 2 (Z) M flexible button 3 (i Self-timer)
1 Press flexible button 3 (Y Smile
timer).
Self-timer
10 s
Smile timer
O
2 Frame the picture.
• Point the camera at a human face.
3 Without pressing the shutter-release button, wait for the subject to
smile.
• If the camera detects that the face framed by the double border is smiling, the shutter is
automatically released.
• Whenever the camera detects a smiling face, it automatically releases the shutter.
4 End automatic shooting.
• To end automatic shooting, set the self-timer to b Off.
Shooting Features
35
B Notes About Smile Timer
Under some shooting conditions, the camera may be unable to detect faces or detect smiles
(A 53). The shutter-release button can also be used for shooting.
C When the Self-timer Lamp Flashes
When using smile timer, the self-timer lamp flashes when the camera detects a face and flashes
quickly immediately after the shutter is released.
Shooting Features
36
Choose a Style (Shooting Suited to Scenes and Effects)
When a style (shooting scenes and effects) is selected, camera settings are automatically
optimized for the selected scene. The expected effect may not be achieved depending on
the subject.
Enter shooting mode M flexible button 3 (g) M flexible button 2 (g Choose a style)
Use the multi selector JK to select the
desired style (shooting scene and effect)
Shoot close-ups
and press flexible button 4 (O).
• To cancel, press flexible button 1 (Q).
D Shoot night scenes1 (A 38)
(default setting)
X Photograph food
J Shoot under water
K Photograph fireworks
2, 3
L Mirror
G Add a neon effect
Q Take soft pictures
1
The camera focuses at infinity.
2
The camera focuses on the area in the center of the frame. When the zoom is set to a position
where the zoom indicator turns green, the camera can focus on subjects as close as about 20 cm
(8 in.) from the front of the protective glass, or about 5 cm (2 in.) at the maximum wide-angle
position.
3
The flash may be unable to light the entire subject at distances of less than 30 cm (1 ft).
4
Use of a tripod is recommended, because the shutter speed is slow.
5
The camera focuses on the area in the center of the frame.
2
(A 38)O Shoot at intervals (A 39)
2, 3
(A 39)I Take a series of pictures (A 40)
1, 4
(A 40)E Shoot backlit scenes5 (A 40)
(A 41)F Add a bubble effect
2, 3
(A 41)H Add a cartoon effect
2, 3
(A 42)M Create a diorama effect
H Shoot close-ups
2, 3
(A 38)
2, 3
(A 41)
2, 3
(A 42)
2, 3
(A 42)
Shooting Features
37
Tips and Notes
D Shoot night scenes
• When the shutter-release button is pressed all the way, the camera captures a series of images
which are combined into a single image and saved.
• Once the shutter-release button is pressed all the way, hold the camera still until a still image is
displayed. After taking an image, do not turn the camera off before the monitor switches to the
shooting screen.
• The angle of view (i.e., the area visible in the frame) seen in the saved image is narrower than
that seen in the monitor at the time of shooting.
• The flash setting is fixed at y Flash off (A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
H Shoot close-ups
Shooting Features
• The camera automatically zooms to the closest position at which it can focus.
• The flash is set to y Flash off, but the setting can be changed (A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
X Photograph food
• The camera automatically zooms to the closest position at which it can focus.
• Use the multi selector JK to adjust the hue setting and press flexible button 4 (O). The hue
setting is saved in the camera’s memory even after the camera is turned off.
• The flash setting is fixed at y Flash off (A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
38
O Shoot at intervals
• The camera can automatically capture still images at pre-determin ed intervals. Images captured
in one shooting are saved in one folder and can be viewed in a slide show (A 58).
• Press flexible button 2 (d Shoot every 30 seconds), flexible button 3 (e Shoot once a
minute), or flexible button 4 (f Shoot every 5 minutes) to set the shooting interval.
• The maximum number of images that can be captured depends on the selected interval.
- Shoot every 30 seconds: Approx. 280 images
- Shoot once a minute: Approx. 140 images
- Shoot every 5 minutes: Approx. 30 images
• Use a sufficiently charged battery to prevent the camera from turning off during shooting.
• Press the shutter-release button all the way down to capture the first image. In between each
shot, the monitor turns off and the power-on lamp flashes. The monitor automatically turns on
again just before the next image is captured.
• Press the shutter-release button halfway to stop shooting.
• The flash is set to w Auto flash, but the setting can be changed (A 31).
• The self-timer is not available (A 33).
J Shoot under water
• When Shoot under water is set, the waterproofing-related messages are displayed.
Confirm each message and press the multi selector K to display the next message.
Press flexible button 4 (O) to skip the messages and change to the shooting screen.
• See “<Important> Shockproof, Waterproof, Dustproof, Condensation” (A xv-xxi) for more
information about using the camera underwater.
• The flash is set to y Flash off, but the setting can be changed (A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
Shooting Features
39
I Take a series of pictures
• The camera captures a series of still images that allow you to clearly see detailed movements in
a moving subject.
• While the shutter-release button is held all the way down, the camera shoots up to 11 images
continuously at a rate of about 4.7 frames per second (fps) (when Choose a size > Photo size
is set to D Large (13 megapixels)).
• The frame rate for continuous shooting may vary depending upon the current photo size
setting, the memory card used, or shooting condition.
• Focus, exposure, and hue are fixed at the values determined with the first image in each series.
• The flash setting is fixed at y Flash off (A 31).
• The self-timer is not available (A 33).
K Photograph fireworks
Shooting Features
• The shutter speed is fixed at about four seconds.
• The flash setting is fixed at y Flash off (A 31).
• The self-timer is not available (A 33).
E Shoot backlit scenes
• When taking images with very bright and dark areas in the same frame, such as backlit scenes,
the high dynamic range (HDR) compositing is applied and loss of details in highlights or
shadows is minimized.
• When the shutter-release button is pressed all the way, the camera shoots images continuously
at high speed, and saves the following two images.
- A non-HDR composite image
- An HDR composite image in which the loss of details in highlights or shadows is minimized
• If there is only enough memory to save one image, an image processed at the time of shooting,
in which dark areas of the image are corrected, is the only image saved.
• Once the shutter-release button is pressed all the way, hold the camera still until a still image is
displayed. After taking an image, do not turn the camera off before the monitor switches to the
shooting screen.
• The angle of view (i.e., the area visible in the frame) seen in the saved image is narrower than that
seen in the monitor at the time of shooting.
• The flash setting is fixed at y Flash off (A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
40
L Mirror
• You can take images that are vertically or horizontally symmetrical over the center of the frame.
• Press flexible button 2 (c Top ➝ bottom) or flexible button 3 (bLeft ➝ right) to set the flip
direction.
When c Top ➝ bottom is selected, the top half of the screen is flipped over the bottom half,
and the image is composited and displayed. When b Left ➝ right is selected, the left half of
the screen is flipped over the right half.
• The flash is set to w Auto flash, but the setting can be changed (A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
F Add a bubble effect
• This effect makes the image appear to be projected on a bubble.
• A guide is displayed in the monitor. Compose the shot so that the main subject is contained
within the guide.
• The flash setting is fixed at w Auto flash, but the setting can be changed (A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
G Add a neon effect
• This effect makes the outlines of the image appear to glow with neon tubing.
• Use the multi selector JK to select the outline color and press flexible button 4 (O). The color
setting is saved in the camera’s memory even after the camera is turned off.
• After taking an image, do not turn the camera off before the monitor switches to the shooting
screen.
• The flash setting is fixed at w Auto flash, but the setting can be changed(A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
Shooting Features
41
H Add a cartoon effect
• Performs tone compensation and makes the image appear like a cartoon.
• After taking an image, do not turn the camera off before the monitor switches to the shooting
screen.
• The flash setting is fixed at w Auto flash, but the setting can be changed(A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
Q Take soft pictures
• Softens the image by adding a slight blur to areas outside of the guide displayed in the monitor.
• A guide is displayed in the monitor. Compose the shot so that the main subject is contained
within the guide.
• The flash is set to w Auto flash, but the setting can be changed (A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
Shooting Features
M Create a diorama effect
• This effect is well-suited for images captur ed from a high vantage point with the main subject in
the center of the image.
• A guide is displayed in the monitor. Compose the shot so that the main subject is contained
within the guide.
• The flash is set to y Flash off, but the setting can be changed (A 31).
• The self-timer can be set, but Y Smile timer is not available (A 33, 35).
42
Decorate
You can add a frame around your images when taking images. Nine different frames are
available.
Enter shooting mode M flexible button 3 (g) M flexible button 3 (A Decorate)
• The C Choose a size > APhoto size setting is fixed at FSmall (2 megapixels)
(A 49).
1 Use the multi selector JK to select
the desired frame and press flexible
Decorate
button 4 (O).
• To cancel, press flexible button 1 (Q).
• You can press flexible button 3 (c) to remove
the frame.
2 Frame the subject and take a picture.
B Notes About Decorate
• The area that is captured becomes smaller when a thicker frame is selected.
• When using borderless printing to print images that you have added frames to, the frames may
not be printed.
Shooting Features
43
Change Colors
You can adjust brightness (exposure compensation) and vividness when taking images. You
can also select one color to keep in your images and turn the rest of the colors to shades of
black and white. See A 46 for details on each effect.
Enter shooting mode M flexible button 3 (g) M flexible button 4 (d Change colors)
1 Use flexible button 2, 3, or 4 to select
the setting.
• Select b Brighter/darker, c More vivid/less
Shooting Features
vivid, or P Highlight colors.
2 Use the multi selector JK to select the
brightness, vividness, or to select the color
you want to highlight.
• The screen displayed when b Brighter/darker is selected
in step 1 is used here as an example.
• Press flexible button 3 (P) to turn the effect off.
44
Change colors
Brighter/darker
More vivid/less vivid
Highlight colors
Brighter/darker
3 Press flexible button 4 (O).
Brighter/darker
1 10 0
20m 0 s
• To cancel, press flexible button 1 (Q).
4 Frame the subject and take a picture.
C Notes About Change Colors
• The setting is saved in the camera’s memory even after the camera is turned off.
• Images adjusted with Change colors are indicated by R.
1100
20m 0s
Shooting Features
45
b Brighter/Darker (Exposure Compensation)
Cursor
Cursor
Cursor
You can adjust overall image brightness.
• Use J to move the cursor to the left to make the overall
image darker. Use K to move the cursor to the right to
make it brighter.
c More Vivid/Less Vivid (Saturation)
You can adjust the overall vividness of the image.
• Use J to move the cursor to the left to make the overall
Shooting Features
image more dull. Use K to move the cursor to the right to
make it more vivid.
P Highlight Colors
You can create a black and white image in which only the
specified color remains.
• Use JK to move the cursor and select the color to
highlight.
Brighter/darker
More vivid/less vivid
Highlight colors
46
Change Sounds
Allows you to configure the shutter and button sounds. You can select one of eight different
sounds, or turn sounds off.
Enter shooting mode M flexible button 4 (l) M flexible button 2 (u Change sounds)
y Pick a shutter sound
Allows you to select the sound heard when the shutter is released and when the focus has
been locked.
When using Take a series of pictures (A 40) or when recording movies, the shutter sound
is not heard.
If you select z, the shutter sound and the sound heard when the focus has been locked are muted.
•
x Pick a button sound
Allows you to select the beep heard when the camera switches between shooting and playback
modes, when using the menus, when the camera is connected to a computer or printer, etc.
• Regardless of this setting, sounds that are heard when an error occurs and when the
camera is turned on do not change.
• If you select z, button sounds and the sounds heard when an error occurs and when the
camera is turned on are muted.
u Turn sounds on or off
Turn all sounds on or off. When the mute is canceled after muting sounds once, the shutter
sound and button sound used before muting will be used again.
Shooting Features
1 Press flexible button 2 or flexible
button 3.
• y Pick a shutter sound: Set the shutter sound.
• x Pick a button sound: Set the button sound.
Change sounds
Pick a shutter sound
Pick a button sound
Turn sounds on or o
47
2 Use the multi selector JK to select the type
of sound.
• y: Set the standard sounds.
• z: Sounds are not heard.
• Press flexible button 3 (A) to play the selected sound.
• To cancel, press flexible button 1 (Q).
• The screen displayed when y Pick a shutter sound was
selected in step 1 is shown here as an example, but the
procedure is the same if you select x Pick a button sound.
3 Press flexible button 4 (O).
• The sound is set.
Shooting Features
Pick a shutter sound
Pick a shutter sound
C Muting All Sounds
On the screen displayed in step 1, press flexible button 4 (u Turn sounds on or off) M flexible
button 3 (z Turn sounds off), in that order, to mute all sounds.
To cancel the mute, press flexible button 4 (u Turn sounds on or off) M flexible button 2 (u Turn sounds on), in that order.
48
Choose a Size
Set the size of photos (still images) and movies.
Choose a Photo Size
Select the combination of image size and compression ratio that is used when saving images.
The higher the image mode setting, the larger the size at which images can be printed, and
the lower the compression ratio, the higher the quality of the images, but the number of
images that can be saved is reduced.
Enter shooting mode M flexible button 4 (l) M flexible button 3 (C Choose a size) M
flexible button 2 (A Photo size)
Option*Size* (pixels)Compression ratio
Large (13 megapixels)
D
(default setting)
E Medium (4 megapixels)2272 × 1704Approx. 1:84:3
F Small (2 megapixels)1600 × 1200Approx. 1:84:3
* The total number of pixels captured, and the number of pixels captured horizontally and vertically.
Example: D Large (13 megapixels) = approx. 13 megapixels, 4160 × 3120 pixels
4160 × 3120Approx. 1:44:3
C Setting the Photo Size
• This setting also applies to Choose a style and Change colors.
• The setting may not be changed when using certain settings of other functions.
Aspect ratio
(horizontal to vertical)
Shooting Features
49
C Number of Images That Can Be Saved
• The approximate number of images that can be saved can be checked in the monitor when
shooting (A 18).
• Note that due to JPEG compression, the number of images that can be saved may vary greatly
depending on the image content, even when using memory cards with the same capacity and
the same photo size setting. In addition, the number of images that can be saved may vary
depending on the make of the memory card.
• If the number of exposures remaining is 10,000 or more, the number of exposures remaining
display shows “9999”.
Choose a Movie Frame Size
Select the desired movie option to record.
Shooting Features
Enter shooting mode M flexible button 4 (l) M flexible button 3 (C Choose a size) M
flexible button 3 (N Movie frame size)
OptionImage size
1
GLarge (1080p) (default setting
HSmall (640)640 × 4804:3Approx. 30 fps
CSmall (old-fashioned)
1
When no memory card is inserted (i.e., when using the camera’s internal memory), you can select
H Small (640) or CSmall (old-fashioned).
2
Allow s you to re cord movie s with an atmosp here and h ue similar to movies shot o n old 8mm f ilm.
) 1920 × 108016:9Approx. 30 fps
2
640 × 4804:3Approx. 15 fps
Aspect ratio
(horizontal to vertical)
50
Frame rate
Functions That Cannot Be Used Simultaneously
Some functions cannot be used with other menu options.
Restricted functionOptionDescription
When Shoot night scenes, Photograph
FlashChoose a style (A 37)
Self-timerChoose a style (A 37)
Smile timer
Decorate
Change colors
Pick a shutter
sound
Photo sizeDecorate (A 43
Print date
Choose a style (A 37)
Highlight colors (A 46)
Smile timer (A 35)
Choose a style (A 37)
Smile timer (A 35)
Choose a style (A 37)
Take a series of pictures
(A 40)
)
Take a series of pictures
(A 40)
food, Take a series of pictures,
Photograph fireworks, or Shoot backlit
scenes is selected, the flash cannot be used.
When Shoot at intervals, Take a series of
pictures, or Photograph fireworks is
selected, the self-timer cannot be used.
When any option in Choose a style is
enabled, Smile timer cannot be used.
When Highlight colors is enabled, Smile timer cannot be used.
When Smile timer is selected, Decorate
cannot be used.
When any option in Choose a style is
enabled, Decorate cannot be used.
When Smile timer is selected, Change colors cannot be used.
When any option in Choose a style is
enabled, Change colors cannot be used.
When Take a series of pictures is selected,
the shutter sound is disabled.
When Decorate is selected, the Photo size
setting is fixed at F Small (2 megapixels).
When Take a series of pictures is selected,
the date cannot be imprinted on images.
Shooting Features
51
Restricted functionOptionDescription
When Shoot night scenes, Shoot at
Electronic VRChoose a style (A 37)
Smile timer (A 35)
Digital zoom
Choose a style (A 37)
Shooting Features
intervals, Take a series of pictures,
Photograph fireworks, or Shoot backlit
scenes is selected, electronic VR is disabled.
When Smile timer is selected, digital zoom
cannot be used.
When Shoot night scenes, Shoot under
water, Shoot backlit scenes, Take soft
pictures, or Create a diorama effect is
selected, digital zoom cannot be used.
52
Focusing
1 10 0
2 0m 0s
The focus area varies depending on the shooting mode and settings.
Using Face Detection
In the following shooting modes and settings, the camera uses
face detection to automatically focus on human faces.
• A Point and shoot (A 30)
• Shoot at intervals (A 39) and Take a series of pictures
(A 40) when using Choose a style
• Smile timer (A 35)
If the camera detects more than one face, a double border is displayed around the face that
the camera focuses on, and single borders are displayed around the other faces.
If no faces are detected when the shutter-release button is pressed halfway, the camera
focuses on the subject in the center of the frame.
B Notes About Face Detection
• The camera’s ability to detect faces depends on a variety of factors, including the direction in
which the faces are looking.
• The camera may be unable to detect faces in the following situations:
- When faces are partially hidden by sunglasses or otherwise obstructed
- When faces take up too much or too little of the frame
1100
20m 0s
Shooting Features
53
Using Skin Softening
When the shutter is released while using one of the shooting modes and settings listed
below, the camera detects human faces and processes the image to soften facial skin tones
(up to three faces).
• A Point and shoot (A 30)
• Smile timer (A 35)
B Notes About Skin Softening
• It may take more time than usual to save images after shooting.
• Under some shooting conditions, the desired skin softening results may not be achieved, and skin
softening may be applied to areas of the image where there are no faces.
Subjects Not Suitable for Autofocus
Shooting Features
The camera may not focus as expected in the following situations. In some rare cases, the
subject may not be in focus despite the fact that the focus area or the focus indicator glows
green:
• Subject is very dark
• Objects of sharply differing brightness are included in the scene (e.g. the sun behind the
subject makes that subject appear very dark)
• No contrast between the subject and surroundings (e.g. a portrait subject wearing a white
shirt is standing in front of a white wall)
• Several objects are at different distances from the camera (e.g. the subject is inside a cage)
• Subjects with repeating patterns (window blinds, buildings with multiple rows of similarly
shaped windows, etc.)
• Subject is moving rapidly
In the situations noted above, try pressing the shutter-release button halfway to refocus
several times, or focus on another subject positioned at the same distance from the camera as
the actual desired subject, and use focus lock (A 55).
54
Focus Lock
1 /2 5 01/250 F 3.3F3.3
1 /2 5 0
F 3.3
Focus lock shooting is recommended when the camera does not activate the focus area that
contains the desired subject. The following explains how to use focus lock when A Point and
shoot is enabled and the focus area is displayed in the center of the frame.
1 Position the subject in the center of
the frame and press the shutterrelease button halfway.
• Confirm that the focus area glows green.
• Focus and exposure are locked.
2 Without lifting your finger, recompose the
picture.
• Make sure to maintain the same distance between the
camera and the subject.
3 Press the shutter-release button the rest of
the way down to take the picture.
1/250
F3.3
Shooting Features
55
Playback Features
4
1 5/ 0 5/ 2 0 14
1 5: 3 0
H
I
Image is zoomed in.Image is displayed full-frame.
Displayed area guide
Playback Zoom
Pressing the multi selector H in full-frame playback mode (A 24) zooms in on the image.
15/05/2014
15:30
4
• You can change the zoom ratio by pressing HI.
Playback Features
• To view a different area of the image, press flexible button 3 (G) to lock the zoom ratio and
press HIJK.
If you want to change the zoom ratio, press flexible button 3 (H) and then change the
zoom ratio as desired.
• If you are viewing an image that was captured using face detection, the camera zooms in
on the face detected at the time of shooting (except when viewing an image size smaller
than 320 × 240). To zoom in on an area of the image where there are no faces, press
flexible button 3 (H) and then press H.
• When a zoomed image is displayed, press flexible button 1 (S) to return to full-frame
playback mode.
h Crop: Creating a Cropped Copy
When using playback zoom, you can crop the image and save the displayed area of the
image as a separate file by pressing flexible button 4 (h).
56
Thumbnail Playback
77
1 5/ 0 5/ 2 0 1415/05/2014 1 5 :3 015:30
Thumbnail PlaybackFull-frame Playback
H
I
Press the multi selector I in full-frame playback mode (A 24) to display images in contact
sheets of thumbnail images.
• While using thumbnail playback mode, press JK to select an image, and the selected
image is magnified and displayed at the center of the screen. Select an image and press H,
and the selected image is displayed in the full-frame playback mode.
Playback Features
57
Functions Available in Playback Mode (Playback Menu)
When viewing images in full-frame playback mode, you can select one of the flexible buttons
(A 6) and display the corresponding menu.
Playback menuOptionDescriptionA
Playback Features
58
V Have fun
with pictures
Z View
Exchange
1
messages
Picture play
Grading
View by date
Slide show
View movie
Allows you to add voice messages to your
images.
1
2
Allows you to edit your images using a variety
of functions.
Allows you to add grade marks to your images.
You can play back only images that have grade
marks. Protects selected images from
accidental deletion.
Allows you to play back images by selecting
the shooting date from the calendar.
Allows you to view images in an automatic
slide show.
Allows you to play back movies (A 63).A 63
E2
E7
E16
E20
E21
Playback menuOptionDescriptionA
Erase this picture
only
n Erase
Erase selected
pictures
Erase all picturesAllows you to delete all images (A 25).A 25
Retouch
l Settings
Print order
Camera settings
1
Available when a still image is displayed.
2
Available when a movie is displayed.
Allows you to delete only the image currently
displayed (A 25).
Allows you to select multiple images and
delete them (A 26).
Allows you to copy or rotate images or create
a small copy of the current image.
Allows you to specify the image to be printed
and the number of copies to be printed.
Allows you to change a number of general
settings (A 65).
A 25
A 26
E27
Playback Features
E32
E34
59
Recording and Playing Back Movies
1 10 01100
20m 0 s20m 0s
Movie recording time
remaining
1 0m 0s10m 0s
Recording Movies
Recording and Playing Back Movies
When no memory card is inserted (i.e., when using the camera’s internal memory), the movie
frame size (A 50) can be set to H Small (640) or CSmall (old-fashioned).
1 Display the shooting screen.
• Check the remaining amount of movie recording time.
2 Press the b (e movie-record) button to start
movie recording.
• The camera focuses on the subject in the center of the
frame.
3 Press the b (e movie-record) button again to end recording.
60
B Maximum Movie Length
Individual movie files cannot exceed 4 GB in size or 29 minutes in length, even when there is
sufficient free space on the memory card for longer recording.
• The maximum movie length for a single movie is displayed on the shooting screen.
• Recording may end before either limit is reached if camera temperature becomes elevated.
• The actual movie length may vary dependi ng on the movie content, subject movement, or type of
memory card.
B Notes About Saving Movies
After a movie has been recorded, it is not fully saved to the internal memory or memory card until
monitor display returns to the shooting display. Do not open the battery-chamber/memory card slot cover or remove the battery or memory card. Removing the memory card or the battery
while a movie is being saved may result in loss of the movie data or damage to the camera or to the
memory card.
B Notes About Movie Recording
• Memory cards with an SD Speed Class rating of 6 or faster are recommended when recording
movies (F23). Movie recording may stop unexpectedly when memory cards with a lower Speed
Class rating are used.
• When recording movies while Electronic VR (A 65, E38) in the camera settings is set to Auto,
the angle of view (i.e., the area visible in the frame) is narrow compared to that of still images.
• The optical zoom ratio cannot be changed once recording starts.
• There may be some degradation in image quality when digital zoom is used.
• The sounds of multi selector operation, autofocus lens drive movement, and aperture operation
when brightness changes may be recorded.
• The following phenomena may be seen in the monitor while recording movies. These
phenomena are saved in the recorded movies.
- Banding may occur in images under fluorescent, mercury-vapor, or sodium-vapor lighting.
- Subjects that move quickly from one side of the frame to the other, such as a moving train or car,
may appear skewed.
- The entire movie image may be skewed when the camera is panned.
- Lighting or other bright areas may leave residual images when the camera is moved.
• Dependi ng on the distance to the subject or the amount of zoom applied, subjects with repeating
patterns (fabrics, lattice windows, etc.) may have colored stripes (interference patterns, moire, etc.)
in them during movie recording and playback. This occurs when the pattern in the subject and the
layout of the image sensor interfere with each other; it is not a malfunction.
Recording and Playing Back Movies
61
B Camera Temperature
• The camera may become warm when shooting movies for an extended period of time or when
the camera is used in a hot area.
• If the inside of the camera becomes extremely hot when recording movies, the camera will
Recording and Playing Back Movies
automatically stop recording.
The amount of time remaining until the camera stops recording (u10s) is displayed.
After the camera stops recording, it turns itself off.
Leave the camera off until the inside of the camera has cooled.
B Notes About Autofocus
Autofocus may not perform as expected (A 54). Should this occur, try the following:
Frame another subject—positioned at the same distance from the camera as the intended
subject—in the center of the frame, press the b (e movie-record) button to start recording, and
then modify the composition.
62
Playing Back Movies
1 5/ 0 5/ 2 0 14
1 5: 3 0
1 0s
1 Press the c (shooting/playback mode) button to switch to playback
mode.
2 Use the multi selector JK to select
the desired movie and press flexible
button 2 (Z).
• Movies can be identified by the movie recording
time indicator (A 5).
3 Press flexible button 4 (G View
movie).
• You can play movies.
15/05/2014
View
View by date
Slide show
View movie
15:30
10s
Recording and Playing Back Movies
63
Functions Available During Playback
5 s
Paused
During playback
Volume indicator
You can use the flexible buttons to perform the
following operations.
Recording and Playing Back Movies
Function IconDescription
Advance
Rewind
PauseD
End
Hold down the button to advance the movie.
B
Hold down the button to rewind the movie.
C
Pause playback. The operations listed below can be performed while paused.
Advance the movie one frame. Hold down the button for continuous
E
advancing.
Rewind the movie one frame. Hold down the button for continuous
F
rewinding.
Resume playback.
A
Return to full-frame playback mode.
S
Adjusting Volume
Press the multi selector HI during playback.
Deleting movies
To delete a movie, select the desired movie in full-frame playback mode (A 24) and press
flexible button 3 (n) (A 25).
5s
64
General Camera Setup
Camera Settings Menu
Enter shooting mode or playback mode M flexible button 4 (l) M flexible button 4
(l Camera settings)
The settings of the menu options listed below can be configured.
OptionDescriptionA
Welcome screen
Date and timeAllows you to set the camera clock.E35
BrightnessAllows you to adjust the brightness of the monitor.E36
Print dateAllows you to imprint the shooting date on images.E37
Electronic VR
AF assistAllows you to enable or disable the AF-assist illuminator.E39
Format memory/
Format card
LanguageAllows you to change the camera’s display language.E41
Menu background
Video modeAllows you to adjust TV-connection settings.E42
Charge by computer
Allows you to select whether or not the welcome screen is
displayed when the camera is turned on.
Allows you to choose whether to use electronic VR (vibration
reduction) when shooting.
Allows you to format the internal memory or the memory card. E40
Allows you to change the background used on the menu
screen.
Allows you to set whether or not the battery in the camera is
charged when the camera is connected to a computer.
E34
E38
E41
E43
General Camera Setup
65
OptionDescriptionA
Reset allAllows you to reset the camera’s settings to their default values. E44
Firmware versionView the current camera firmware version.E44
General Camera Setup
66
Connecting the Camera to a TV,
Insert the plug straight.
USB/audio/video output connector
Open the cover.
HDMI micro connector (Type D)
Computer, or Printer
Connection Methods
You can enhance your enjoyment of images and movies by connecting the camera to a TV,
computer, or printer.
1
2
3
• Before connecting the camera to an external device, make sure the remaining battery level
is sufficient and turn the camera off. Before disconnecting, make sure to turn the camera
off.
• If the AC Adapter EH-62G (available separately) is used, this camera can be powered from
an electrical outlet. Do not use any other make or model of AC adapter as it may cause the
camera to heat up or malfunction.
• For information about the connection methods and subsequent operations, refer to the
documentation included with the device in addition to this document.
Connecting the Camera to a TV, Computer, or Printer
67
Viewing images on a TVE45
Images and movies captured with the camera can be viewed on a TV.
Connection method: Connect the video and audio (stereo) plugs of the
Connecting the Camera to a TV, Computer, or Printer
Viewing and organizing images on a computerA 69
Printing images without using a computerE48
optional audio video cable to the TV’s input jacks. Alternatively, connect a
commercially available HDMI cable to the TV’s HDMI input jack.
You can transfer images to a computer to perform simple retouching and
manage image data.
Connection method: Connect the camera to the computer’s USB port with
the USB cable.
• Before connecting to a computer, install ViewNX 2 on the computer
(A 69).
• If any USB devices that draw the power from the computer are connected,
disconnect them from the computer before you connect the camera to it.
Connecting the camera and other USB-powered devices to the same
computer simultaneously may cause a camera malfunction or excessive
power supply from the computer, which could damage the camera or
memory card.
If you connect the camera to a PictBridge-compatible printer, you can print
images without using a computer.
Connection method: Connect the camera directly to the printer’s USB port
with the USB cable.
68
Using ViewNX 2
Your Imaging Toolbox
ViewNX 2™
Install ViewNX 2 to upload, view, edit, and share photos and movies.
Installing ViewNX 2
An Internet connection is required.
For system requirements and other information, see the Nikon website for your region.
Connecting the Camera to a TV, Computer, or Printer
1 Download the ViewNX 2 installer.
Start the computer and download the installer from:
http://nikonimglib.com/nvnx/
2 Double-click the downloaded file.
3 Follow the on-screen instructions.
4 Exit the installer.
Click Yes (Windows) or OK (Mac).
69
Transferring Images to the Computer
3
1
2
1 Choose how images will be copied to the computer.
Connecting the Camera to a TV, Computer, or Printer
Choose one of the following methods:
• Direct USB connection: Turn the camera off and ensure that the memory card is inserted
in the camera. Connect the camera to the computer using the USB cable. The camera
automatically turns on.
To transfer images that are saved in the camera’s internal memory, remov e the memory card
from the camera before connecting it to the computer.
• SD card slot: If your computer is equipped with an SD card slot, the card can be inserted
directly in the slot.
• SD card reader: Connect a card reader (available separately from third-party suppliers) to
the computer and insert the memory card.
70
If a message is displayed prompting you to choose a program, select Nikon Transfer 2.
Start Transfer
• When using Windows 7
If the dialog shown at right is displayed,
follow the steps below to select Nikon
Transfer 2.
1Under Import pictures and videos, click
Change program. A program selection
dialog will be displayed; select Import File using Nikon Transfer 2 and click OK.
2Double-click Import File.
If the memory card contains a large number of images, it may take a while for Nikon Transfer 2
to start. Wait until Nikon Transfer 2 starts.
B Connecting the USB Cable
The connection may not be recognized if the camera is connected to the computer via a USB hub.
2 Transfer images to the computer.
• Click Start Transfer.
• At default settings, all the images on the memory card will be copied to the computer.
Connecting the Camera to a TV, Computer, or Printer
71
3 Terminate the connection.
• If the camera is connected to the computer, turn the camera off and disconnect the USB
cable. If you are using a card reader or card slot, choose the appropriate option in the
Connecting the Camera to a TV, Computer, or Printer
computer operating system to eject the removable disk correspond ing to the memory card,
and then remove the card from the card reader or card slot.
Viewing Images
Start ViewNX 2.
• Images are displayed in ViewNX 2 when transfer is
complete.
• Consult online help for more information on
using ViewNX 2.
C Starting ViewNX 2 Manually
• Windows: Double-click the ViewNX 2 shortcut icon on the desktop.
• Mac: Click the ViewNX 2 icon in the Dock.
72
Reference Section
The Reference Section provides detailed information and hints about using the camera.
Have Fun with Pictures
E Exchange Messages................................................................................ E2
V Picture Play ................................................................................................ E7
A Grading ..................................................................................................... E16
View
G View by Date ...........................................................................................E20
m Slide Show ............................................................................................... E21
G View Movie .............................................................................................. E26
Settings
y Retouch..................................................................................................... E27
a Print Order ............................................................................................... E32
l Camera Settings ...................................................................................... E34
Connections
Connecting the Camera to a TV ............................................................. E45
Connecting the Camera to a Printer..................................................... E47