NEXXT SOLUTIONS 320U1 User Manual

Nexxt Solutions - Integrated Wireless IP Camera

HTTP Port - In most cases, you can leave this value as 80; however, if your Internet Service Provider blocks this port, you may have to switch to another port number, such as 8005.

Wireless LAN Settings

Enter the wireless settings page of the Wireless Router to ﬁnd out the SSID, Channel, Encryption and Authentication details. This product supports WEP and WAP security encryption methods.

ADSL Settings

When connected to the Internet through ADSL, you can enter the ADSL username and password obtained directly from your ISP.

Nexxt Solutions - Integrated Wireless IP Camera

DDNS Service Settings

The system supports protocols from some DDNS providers such as dyndns.org. Fill in the following ﬁelds once the DDNS service has been setup.

User and Password: The User Name and Password used when applying for the domain name.

DDNS Host: The domain name. DDNS or Proxy Server: If you access the DDNS host

through a proxy, you should enter the Proxy IP here.

DDNS or Proxy Port: The Proxy Port.

Mail Service Settings

Conﬁgure the email addresses that will receive and send mails after an alarm is triggered.

Sender - This device uses the sender mailbox to send mails. Receiver – The account used to receive mails from the Sender. You can set up to 4 receiver mailboxes. SMTP Server - The SMTP server for the sender mailbox.

Nexxt Solutions - Integrated Wireless IP Camera

Need Authentication - Check the box if the email needs authentication. If so, please enter the SMTP User Name & Password. Mail test: Set the Mail parameters and click ‘Submit’ before attempting to send a test email.

There are 8 possible Mail Test errors:

1. Cannot connect to the server.

2. Network Error. Please try later.

3. Server Error.

4. Incorrect username or password.

5. The Sender is denied by the server - The server needs to authenticate the user; check settings and try again.

6. The Receiver is denied by the server - Could be caused by the anti-spam privacy settings of the server.

7. The message is denied by the server - Could be caused by the anti-spam privacy settings of the server.

8. The server does not support the authentication mode used by the device. Report Internet IP by Mail - Check the box so when the IP camera is powered on or the Internet IP address changes, an email will be

Nexxt Solutions - Integrated Wireless IP Camera

sent. (For example: XPY 320`s address is http://119.123.207.96:9002). Make sure the port is mapped to the router correctly by UPnP or Virtual Map function.

FTP Service Settings Note: When under Alarm Service Settings the

option “Upload Image on Alarm” is checked, the FTP Service takes effect.

FTP Server - The FTP server address. FTP port - The port usually is 21. FTP Mode - Supports standard (PORT) mode and

passive (PASV) mode. Upload Image Now - Check the box to upload an image. When checked, you can input the upload interval time in seconds. FTP Test - Set the FTP parameters and then click ‘Submit’ before testing the FTP settings. If successful, the user will be prompted accordingly. Otherwise, an error message will be displayed. There are 8 possible FTP test errors:

1. Cannot connect to the server - Please check FTP Server settings.

2. Network Error. Please try later.

3. Server Error.

Nexxt Solutions - Integrated Wireless IP Camera

4. Incorrect username or password - Check the username and password.

5. Cannot access the folder - Ensure the folder exists and your account is authorized.

6. Error in PASV mode - Ensure the server supports PASV mode.

7. Error in PORT mode - PASV mode should be selected if the device is behind a NAT.

8. Cannot upload ﬁle - Ensure your account is authorized.

Alarm Service Settings (Motion Detection)

Enter the Alarm Service Settings page to conﬁgure the Motion Detection function. When motion detection is enabled, the camera can be triggered to send email alerts and upload images. In the camera monitoring page, the green icons will turn to red and you will hear an alert sound if motion is detected.

Note: The default path for saving recorded ﬁles is C:\Documents and Settings\All Users\Documents.

Motion Detection Sensitivity - Sensitivity can be determined in a scale from 1 to 10, 1 being the

Nexxt Solutions - Integrated Wireless IP Camera

setting with the highest motion detection sensitivity, while 10 represents the lowest sensitivity available you can preset.

Send Mail on Alarm - Sends picture & mail information to the set email address after the alarm is triggered.

Upload Image on Alarm - Enable this function to upload an image after the alarm is triggered.

REC on schedule and save to PC - Enable this function for automatic recording to start on the scheduled time for several seconds, and save the video in the PC when an alarm has been triggered.

ACCESSING THE IP CAMERA

Using the WiFi capability

To use the wireless feature of the IP Camera, a wireless router is required. Follow the instructions below to get started after the camera has been mounted properly.

1. Use the Network cable to connect the IP Camera to the LAN.

2. Enter IP Camera Tool to search for the camera.

3. When IP address of the camera is listed in the Result Field of the IP Camera Tool, it means the basic conﬁguration is completed.

4. Set the security settings in Internet Explorer on the PC when you view it for the ﬁrst time.

5. Log in to the web browser of the IP camera.

6. Now you can use the IP Camera as a Visitor, Operator or Administration in the LAN.

+ 14 hidden pages