Nex 920-0010 Owner's Manual

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUALS

®

OUTDOOR PATIO HEATER

Model 920-0010

A02Y07P-2

Warning: For outdoor Use Only

IMPORTANT

Read this manual carefully before assembling, using or servicing this
heater. Keep this manual for future reference. If you have questions about
assembly, operation, servicing or repair of this heater, please call Nexgrill
Industries., Inc at 1-866-984-7455

1

Table of Contents

Table of contents & Warning…………………………2 -3
Tools and parts needed for assembly………………….4
Assembly Instruction…………………………………..5 -10
Gas Requirement & Leak testing……………………...11
Safety Checks……………………………………………12
Location heater for use………………………………13-15
Storage burner removal…………………………………16
Burner installation / Pilot cleani ng……………………..17
Trouble Shooting…………………………………………18
Part List……………………………………………………19
Limited Warranty…………………………………………20

General Safety Information

This manual contains important information about the assembly, opera­tion and maintenance of this portable heater. General safety information
Presented in these first few pages and is also located throughout the man­ual. Particular attention should be paid to information accompanied by the
Safety alert symbols: DANGER, WARNING, CAUTION

Keep this manual for future reference and to educate new users of this
Product. This manual should be read in conjunction with the labeling on the
Product.

Safety precautions are essential when any mechanical or propane fueled
Equipment is involved. These precautions are necessary when using, stor­Ing, and servicing. Using this equipment with the respect and caution
Demanded will reduce the possibilities or personal injury or property damage

The following symbols shown below are used extensively throughout this
Manuals. Always heed these precautions, as they are essential when using
Any mechanical or fueled equipment.

DANGER

DANGER indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury

WARNING

WARNING indicates a potentially haza rdou s sit uation which, if
not avoided, could result in death or serious injury

CAUTION

DANGER indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury

CAUTION

If you smell gas:

1. Shut off gas to the appliance

2. Extinguish open flame

3. If odor continues, immediately call your gas
supplier.

2

PRECAUTIONS

¾Do not use this space heater in an explosive atmosphere.

Keep heater away from areas where gasoline or other
flammable liquids or vapors are stored.

¾Prior to use, check for damaged parts such as hoses

regulator, pilot or burner.

¾Do not attempt to alter unit in any manner. EXAMPLE:

using the heater without the top canopy reflector or radiant
screen. Do not shorten the burner post assembly.

¾Heater must always be placed on a solid and level surface.
¾Always maintain proper clearance to combustible materials.

Top 18” (46cm) Side 24”(61cm).

¾Always assure there is ample fresh air ventilation for

outdoors use ONLY.

¾Never replace or substitute the regulator with any regulator

other than the factory suggested replacement.

¾Do not clean heater with cleaners that are combustible or

corrosive

¾Do not paint radiant screen, control panel or top canopy

reflector.

¾All leak tests should be done with a soapy solution NEVER

USE AN OPEN FLAME TO CHECK FOR LEAKS.

¾The LP tank should be turned off when the heater is not in use
¾At least once a year, the unit should be inspected for the presence

of spiders, spider webs or other insects. The burner are a is a
common spider haven and can damage the heater and render it

unsafe for use, Check the heater immediately if any of the

following exists:

1. The smell of gas in conjunction with extreme yellow tipping of
the burner flames

2. The heater does nor reach temperature.

3. The burner makes a popping noise during use (a slight popping

noise is normal when the burner is extinguished).

¾The LP regulator/ hose assembly should be located out of

pathways Where people may trip over it or in area where the hose
will not be subject to accidental damage.

¾Children and adults should be aware of hazards of high surface

temperature and should stay away to avoid burns of clothing
ignition.

¾Young children should be carefully supervised when they are in

the area of the heater.

¾Clothing or other flammable material should not be hung from the

heater, or placed on or near the heater.

3

TOOLS AND PARTS NEEDED FOR ASSEMBLY

NOTE: 20 pound (9.0 kgs), 5 Gallon (18.9 liters) LPG Tank is not supplied

Tools Needed:

Phillips Head Screwdriver
Two Adjustable Opening Wrenches
Spray Bottle of Soapy Water (To check for leaks)

Parts supplied:

Railing (2)Reflector Dome Cap (1)
Rubber Post Gasket (1)Reflector Plate (1)
Granite Table Rubber Ring (1)Reflector (3)
Pole with Support Bracket (1)Emitter Grid (1)
Gas Tank Enclosure Assembly (1)Heater Head With PVC Hose Assembly (1)
LPG Gas regulator with Hose (1)Emitter Screen (2)
Tank Hook (1)Post (1)
Electronic Ignitor Module (1)Granite Table (1)

Hardware Bag

Support Pole Ø 1/4” Nut (4)
Support Pole Ø 1/4” Flat Washer (4)
Support Pole Ø 1/4” Spring Washer (4)
Granite Table Ø 1/4” x 15mm Truss Head Screw (2)
Emitter Grid Ø3/16” x 10mm Truss Head Screw (4)
Secure Guard Ø 1/4” x 20mm Truss Head Screw (4)
Secure Guard Ø 1/4” Flat Washer (4)
Heater Body Ø 1/4” x 25mm Flat Head Screw (3)
Reflector Ø5/32” x 8 mm Truss Head Screw (6)
Reflector Ø 1/4”x 8mm Truss Head Screw (3)
Reflector Nut (1)

Tank hook Ø 3/16 x 4 Flat Head Screw(4)
Tank hook Ø 3/16 x 4 Flat Washer(4)

Reflector Ø1/4” x 82mm Threaded Ends Stud (1)

For Service Questions Replacement parts or other assistance, Please call Nexgrill Customer Service
Hotline at: Nexgrill Industries, Inc

280 Machlin Court, City of Industry, CA91789
[phone]

4

Assembly Instruction

STEP 1. Attach Pole with Support
Bracket

● Put the Pole with Support Bracket
into the Tank hole.

● Secure the Pole with 4 pcs the 1/4”
Flat Washers, 1/4” Lock Washers and
1/4” Nuts

5

STEP 2. Secure the Granite Table

● Align the cut out portion of the
Granite Table Rubber Ring with the

openings in the Granite Table Support
Bracket

● Align the screw holes in the
underside of the Granite Table with the

holes in the Granite Table Support
Bracket. Using 2 - 1/4” x 15mm Truss
Head Screw, attach the Granite Table
to the Granite Table Support Bracket as
shown in the diagram to the left.

Assembly Instruction

STEP 3. Attach the Emitter Grid

● Put the Emitter Grid on the Emitter
base.

● Secure the Emitter Grid with 4pcs
3/16” x 10mm Truss Head Screws as
shown in the diagram to the left.

6

STEP 4. Attach the Post

● Put the head assembly into the post.

● Please make sure the Gas Hose

End and two wires go through the post.
Do not secure the heat assembly in
this step.

Assembly Instruction

STEP 5. Heater Body Assembly

● Put the Post into the hole of
Granite Table. Please make sure that
the Gas Hose End and two Wires go
through the hole and can be reached
from the interior of the Base Housing.

● Turn the Post clockwise until it
is tightly secured.

● Turn the head assembly to align
the Control Panel to the same side as
the Door of the Base Housing.
Secure the Heater Body with 3pcs 1/4”
x 25mm Flat Head Screws as shown
in the diagram to the left.

STEP 6. Emitter Screen Assembly

● The Emitter Screen comes as two
pieces which fit together just under the
base of the Emitter Screen. Needed for
this step are 4 - 1/4” x 20mm Truss

Head Screws and 4 - 1/4” Flat Washers.

● Align the open area at the bottom of
the Emitter Screen with the four holes in
the Control Panel Housing and using the
4 screws with washers installed on the
screws attach the Emitter Screen to the
Control Panel Housing as shown in the
diagram to the left.

7