Nex 720-0539, 720-0543, 720-0466, 720-0549, 720-0536 Owner's Manual
...
ASSEMBLY & OPERATING INSTRUCTIONS
Model: 720-0466
FOR PROPANE GAS USE ONLY
PLEASE CONTACT 0239-2322880 FOR ASSISTANCE
ABOUT ASSEMBLY OR GRILL OPERATION
DO NOT RETURN TO THE PLACE OF PURCHASE
FOR OUTDOOR USE ONLY
L17Y07P_1
1
Table of Contents
Safety Instruction . . . . . . . . . . . . . . . . . . . . .
Assembly Instruction . . . . . . . . . . . . . . . . . .
Gas Hook –Up . . . . . . . . . . . . . . . . . . . . . . .
Installer Final Check List . . . . . . . . . . . . . . .
Leak Testing . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instruction . . . . . . . . . . . . . . . . . .
Grill Lighting Instruction . . . . . . . . . . . . . . . .
Lighting Illustration . . . . . . . . . . . . . . . . . . . .
To Match the Light Grill . . . . . . . . . . . . . . . .
2-7
8-13
14-15
15
16-17
18
19-20
21
22
Motor Instruction . . . . . . . . . . . . . . . . . . . . . . . . . .
Care and Maintenance . . . . . . . . . . . . . . . . . . . . .
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . .
Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grill Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grill Cooking Chart . . . . . . . . . . . . . . . . . . . . . . . .
Grill Recipe Suggestion . . . . . . . . . . . . . . . . . . . . .
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . .
23
24-25
26-29
30
31-32
33
33
34-35
36-38
39
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from
the appliance and immediately call
you gas supplier or your fire
department.
Failure to comply with these instructions could result in a fire or explosion that could cause serious bodily
injury, death, or property damage.
Combustion by products produced when using this product contain chemicals known to the States of
California to cause cancer, birth defects, or other reproductive harm
Your grill will very hot. Never lean over the cooking area while using your grill. Do not touch cooking
surfaces, grill housing, lid or any other grill parts while the grill is in operation, or until the gas grill has
cooled down after use.
Safety Instruction
WARNING
1. Do not store or use gasoline or other
flammable liquids or vapors in the
vicinity of this or any other
appliance.
2. An LP cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
2
Safety Instruction continued
WARNING
ELECTRICAL GROUNDING INSTRUCTIONS This appliance (rotisserie motor) is equipped with a plug
and should be plugged directly into a properly grounded receptacle. When installed, must be electrically grounded
in accordance with local codes or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70
or the Canadian Electrical Code, CSA C22.1 DO NOT cut or remove the grounding prong from this plug.
1. To protect against electric shock, do not immerse cord or plugs in water or other liquid.
2. Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off
parts.
3. Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance
malfunctions or has been damaged in any manner. Contact the manufacturer for repair.
4. Do not let the cord hang over the edge of a table of touch hot surface.
5. Do not use an outdoor cooking gas appliance for purposes other than intended.
6. When connecting, first connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.
7. Use only a Ground Fault Interrupt (GFI) protected circuit with this outdoor cooking gas appliance.
8. Never remove the grounding plug or use with an adapter of 2 prongs.
9. Use only extension cords with a 3 prong grounding plug, rated for the power of the equipments, and
approved for outdoor use with a W-A marking.
3
Safety Instruction continued
WARNING
Do not try lighting this appliance without reading the
“LIGHTING INSTRUCTIONS” section of this manual.
TESTED IN ACCORDANCE WITH ANS
Z21.58 CSA 1.6-2007 STANDARD FOR
OUTDOOR COOKING GAS APPLIANCE.
THIS GRILL IS FOR OUTDOOR USE
ONLY.
Grill Installation Codes
Check your local building codes for the proper method of
installation. in the absence of local codes, this unit
should be installed in accordance with the National Fuel
Gas Code ,ANSI Z223.1/NFPA 54,Storage and Handling
of Liquefied Petroleum Gases, ANSI /NFPA B149.2 or
CSA B149.1 Natural Gas and Propane Installation Code,
and the National Electrical Code, ANSI/NFPA 70.
Correct LP Gas Tank Use
LP gas grill models are designed for use with a standard
20 lb. Liquid Propane Gas tank, not included with grill.
Never connect your gas grill to an LP gas tank that
exceeds this capacity.
CAUTION: Beware of Flashback
CAUTION: Spiders and small insects occasionally
spin webs or make nest in the grill
burner tubes during transit and
warehousing. These webs can lead
to gas flow obstruction, which could
result in a fire in and around burner
tubes. This type of fire is known as
“FLASH-BACK” and can cause serious damage to
your grill and create an unsafe operating condition for
the user.
Although an obstructed burner tube is not the only
cause of “FLASH-BACK”, it is the most common
cause.
To reduce the chance of “FLASH-BACK”, you must
clean the burner tubes before assembling your grill,
and at least once a month in late summer or early fall
when spiders are most active. Also perform this
burner tube cleaning procedure if your grill has not
been used for an extended period of time. A clogged
tube can lead to a fire beneath the grill.
If an external electrical source is utilized: The outdoor
cooking gas appliance, when installed, must be
electrically grounded in accordance with local codes or,
in the absence of local codes, with the National Electric al
Code, ANSI/NFPA 70, or the Canadian Electrical Code,
CSA C22.1.
WARNING
Keep any electrical supply cord and the fuel supply hose
away from any heated surfaces.
NOTE: The normal flow of gas through the regulator and
hose assembly can create a humming noise. A low
volume of noise is perfectly normal and wil
with operation of the grill. If humming noise is loud and
excessive you may need to purge air from the gas line or
reset the regulator excess gas flow device. This purging
procedure should be done every time a new LP gas tank
is connected to your grill.
l not interfere
Visually check the burner flames prior to each use.
The flames should look like this picture. If they do not,
refer to the burner main tenancy part of this manual.
4
LP-Gas Supply System
Safety Instruction continued
If the information is not followed exactly, a fire resulting in death or
serious injury could occur.
A 20lb tank of approximately 12 inches in diameter by 18-1/4 inches
high is the maximum size LP gas tank to use.
This safety feature prevents the tank from being overfilled, which
can cause malfunction of the LP gas tank, regulator and/or grill.
The LP gas supply cylinder to be used must be constructed and
marked in accordance with the specifications for LP –Gas cylinder of
the U.S. Department of Transportation (DOT) or the National
Standard of Canada ,CAN/CSA –B339, Cylinders, Spheres and
Tubes for Transportation of Dangerous Goods and Commission .
The LP gas tank must have a shutoff valve terminating in an LP
valve outlet that is compatible with a Type 1. LP gas supply cylinder
must have a shut off valve terminating in a valve outlet specified for
connection type QCC1 in the standard for compressed gas cylinder
valve outlet and inlet connection ANSI/CGA-V-1 as applicable. LP
gas supply cylinder must be fitted with an Overfill Protection Device
(O.P.D) The LP gas tank must also have a safety relief device that
has a direct connection with the vapor space of the tank.
The tank supply system must be arranged for vapor withdrawal.
The LP gas tank used must have a collar to protect the tank valve
Place dust cap on cylinder valve outlet whenever the cylinder is not
in use. Only install the type of dust cap on the cylinder valve outlet
that is provided wit the cylinder valve. Other types of cap or plugs
may result in leakage of propane
Never connect an unregulated LP gas tank to your gas grill.
This outdoor cooking gas appliance is equipped with a high capacity
hose/regulator assembly for connection to a standard 20lb. Liquid
propane cylinder.
Have your LP gas tank filled by a reputable propane gas
dealer and visually inspected and re-qualified at each filling.
Do not store a spare LP gas cylinder under or near this
appliance.
Never fill the cylinder beyond 80 percent full .
Always keep LP gas tanks in an upright position.
Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
Storage of an outdoor cooking gas appliance indoors is permissible
only if the cylinder is disconnected and removed from the outdoor
cooking gas appliance..
When your gas grill is not in use the gas must be turned off at LP
gas tank.
•The gas must be turned off at the supply cylinder when the outdoor
cooking gas appliance is not in use.
•LP gas tank must be stored outdoors in a well-ventilated area and
out of reach of children. Disconnected LP gas tanks must not be
stored in a building, garage or any other enclosed area.
PROPER PLACEMENT AND CLEARANCE OF
GRILL
•Never use your gas grill in a garage, porch, shed,
breezeway or any other enclosed area. Your gas grill i s
to be used outdoors only.
•Do Not install this unit into combustible enclosures.
•Minimum clearance from sides and back of unit to
combustible construction, 24 inches (61cm) from sides
and 24 inches (61cm) from back.
•DO NOT use this appliance under overhead
combustible surfaces. This outdoors cooking gas
appliance is not intend to be installed in or on
recreational vehicles and/or boats.
•Do Not obstruct the flow of ventilation air around the
gas grill housing. Only use the regulator and the hose
assembly supplied with your gas grill. Replacement
regulators and hose assemblies must be those specified
in this manual.
•The regulator and hose assembly must be inspected
before each use of the grill. If there is excessive
abrasion or wear or if the hose is cut, it must be
replaced prior to the grill being put into operation. The
replacement hose assembly shall be that specified by
the manufacturer.
•Pressure regulator and hose assembly supplied with
the outdoor cooking gas appliance must be used. Never
substitute other types of regulator. Contact customer
service for manufacturer specified replacement parts.
•This outdoor cooking gas appliance is equipped with a
pressure regulator comply with the standard for
Pressure Regulating Valves for LP Gas ANSI/ UL 144.
•Do not use briquettes of any kind in the grill.
•The grill is designed for optimum performance without
the use of briquettes. Do not place briquettes on the
radiant as this will block off the area for the grill burners
to vent. Adding briquettes can damage ignition
components and knobs, and void the warranty.
•Keep the back and side cart free and clear from debris.
Keep any electrical supply cord, or the rotisserie motor
cord away from the heated areas of the grill.
•Never use the grill in extremely windy conditions. If
located in a consistently windy area (oceanfront,
mountaintop, etc.) a windbreak will be required. Always
adhere to the specified clearance.
•Never use a dented or rusty propane tank.
•Keep any electrical supply cord and the fuel supply
hose away from any heated surface
•While lighting, keep your face and hands as far away
from the grill as possible.
•Burner adjustment should only be performed after the
burner has cooled.
5
Safety Instruction continued
WARNING
Your grill will get very hot. Never lean over the
cooking area while using your grill. Do not touch
cooking surfaces, grill housing, lid or any other grill
hot surface while the grill is in operation, or until the
gas grill has cooled down after use.
Failure to comply with these instructions may
result in serious bodily injury.
ROTISSERIE DRIVE MOTOR
USE ONLY FOR OUTDOORS, DO NOT EXPOSE
TO RAIN.
CAUTION: TO ENSURE CONTINUED
PROTECTION AGAINST RISK OF ELECTRIC
SHOCK, CONNECT TO PROPERLY GROUNDED
OUTLETS ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK, KEEP EXTENSION CORD
CONNECTION DRY AND OFF THE GROUND.
INSECT WARNING:
Spiders and insects can nest in the burners of this
and any other grill, and cause the gas to flow
improperly. This is a very dangerous condition, which
can cause a fire to occur behind and beneath the
valve panel, thereby damaging the grill and making it
unsafe to operate. Inspect the grill at least twice a
year.
WARNING
Keep a spray bottle of soapy water near the gas
supply valve and check the connections before each
use.
DO NOT USE ALUMINUM FOIL TO LINE THE
GRILL RACKS OR GRILL BOTTOM.
This can severely upset combustion airflow or trap
excessive heat in the control area.
SAFETY PRACTICES TO AVOID PER S ONAL
INJURY
When properly cared for, your grill will provide safe,
reliable service for many years. However, extreme
care must be used as the grill produces intense heat
that can increase accident potential. When using this
appliance basic safety practices must be followed,
including the following:
Do not repair or replace any part of the grill unless
specifically recommended in this manual. All other
service should be refer
This grill is not intended to be installed in or on
recreational vehicles or boats
Children should not be left alone or unattended in an
area where the grill is being used. Do not allow them to
sit, stand or play in or around the grill at any time.
Do not store items of interest to children around or
below the grill.
Do not permit clothing, pot holders or other flammable
materials to come in contact with or too close to any
grate, burner or hot surface until it has cooled. The
fabric could ignite and cause personal injury.
For personal safety, wear proper apparel. Loose fitting
garments or sleeves should never be worn while using
this appliance. Some synthetic fabrics are highly
flammable and should not be worn while cooking.
Only certain types of glass, heat-proof glass ceramic,
earthenware, or other glazed utensils are suitable for
grill use. These materials may break with sudden
temperature changes. Use only on low or medium heat
settings in accordance with the manufacturer’s
guidelines.
red to a qualified technician.
DO NOT LEAVE THE GRILL UNATTENDED
WHILE COOKING.
6
Safety Instruction continued
Do not heat unopened food containers. A build-up of
pressure may cause the containers to burst.
Use a covered hand when opening the grill lid.
Never lean over an open grill.
When lighting a burner, pay close attention to what
you are doing. Make certain you are aware of which
burner you are lighting, so your body and clothing
remain clear of open flames.
When using the grill, do not touch the grill rack, burner
grate or immediate sur
become extremely hot and could cause burns. Use
only dry potholders. Moist or damp potholders on hot
surfaces may cause steam burns. Do not use a towel
or bulky cloth in place or potholders. Do not allow
potholders to touch hot portions of the grill rack.
Grease is flammable. Let hot grease cool before
attempting to handle it. Do not allow grease deposits
to collect in the grease tray at the bottom of the grill’s
firebox. Clean the grease tray often.
roundings as these areas
Do not use the grill to cook excessively fatty meats or
other products which promote flare – ups.
Do not operate the grill under unprotected combustible
constructions. Use only in well ventilated areas. Do
not use in buildings, garages, sheds, breezeways or
other such enclosed areas.
Keep the area surrounding the grill free from
combustible materials including fluids, trash, and
vapors such as gasoline or charcoal lighter fluid. Do
not obstruct the flow of combustion and air ventilation.
WARNING
This outdoor cooking gas appliance is not
intended to be installed in or on boats. For
other than RV grills, a statement that this
appliance is not intended to be installed in or
on recreational vehicles.
Do not use aluminum foil to line the grill racks or grill
bottom. This can severely upset combustion air flow or
trap excessive heat in the control area.
For proper lighting and performance of the burners
keep the burner ports clean. It is necessary to clean
them periodically for optimum performance. The
burners will only operate in one position and must be
mounted cor
Clean the grill with caution. To avoid steam burns, do
not use a wet sponge or cloth to clean the grill while it
is hot. Some cleaners produce toxic fumes or can
ignite if applied to a hot surface.
Turn off grill controls and make certain the grill is cool
before using any type of aerosol cleaner on or around
the grill. The chemical that produces the spraying
action could, in the presence of heat, ignite or cause
metal parts to cor
rectly for safe operation.
rode.
7
Assembly Instruction
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND FOLLOW STEP BY
STEP
► Propane Tank is not include
► Phillips head Screwdriver (not provided)
STEP 1: The screws used to attach the side shelf are already screwed into the left panel (see the
figure below). Remove the screws from the left panel and control panel, align with the holes in the
side shelf, and then re-screw into the holes on the left panel and control panel of the grill.
8
Assembly Instruction continued
STEP 3: The front 2 screws used to attach the push bar are screwed into the right panel (see
the figure below). align with the holes in the push bar, and then screw into the holes on the
right panel of the grill. The back screw has already screwed into the push bar , loosen the
screw and attach the back side push bar to the right panel. Press the cap against the ends
of the push bar, and gently tap them into place.
9
Assembly Instruction continued
STEP 3: Find the 4 screws used to attach the right push bar brackets. Align with the holes on the
right panel beneath the push bar. Insert the screws and loosely attach the brackets. Locate the 2
screws which will attach the bracket
screws will install from the under side of the push bar through the hole in bracket. Insert the screws
and then tighten the screws attaching the bracket to the right panel. then put the service tray on it.
to the push bar itself, as shown in the diagram below. These
2 sets each side
10
Assembly Instruction continued
STEP 4: Battery is inserted for the Rotisserie burner . To install the battery, turn the ignition button
cap counterclockwise and remove it. Replace the ignition button cap after the bat
tery are installed.
11
Assembly Instruction continued
STEP 5: The screws for rotisserie drive motor bracket are screwed into the right side of the grill
housing. Remove the screws and install the rotisserie motor bracket as shown in the figure below.
Assemble the rotisserie skewer as shown in the figure below.
12
Loading...