Nex 720-0419 Owner's Manual

ASSEMBLY & OPERATING INSTRUCTIONS

Model: 720-0419

FOR PROPANE GAS USE ONLY

PLEASE CONTACT 1-800–648–5864 FOR ASSISTANCE
ABOUT ASSEMBLY OR GRILL OPERATION
DO NOT RETURN TO THE PLACE OF PURCHASE

FOR OUTDOOR USE ONLY

I21Y06P-2

MESSAGE TO OUR CONSUMERS

Thank you for selecting our stainless steel gas grill.

Because this appliance contains features which may not be found on other grills, we
recommend that you read this entire booklet before your first use. Keep it in a handy
place as it has answers to questions that may occur during future use.

Read this booklet carefully and be sure your gas grill is properly assembled, installed and
maintained. Failure to follow these instructions could result in serious bodily injury and/or
property damage. This gas grill is intended for outdoor use only and is not intended to be
installed in or on recreational vehicles or boats.

NOTE TO INSTALLER: Leave these instructions with the consumer after installation.
NOTE TO CONSUMER: Retain for future reference.

IMPORTANCE

Danger

I f you smell gas:
1 S hut off gas to the appliance.
2 Extinguish any open flame.

3 Open lid
4 If odor continues, keep away from the appliance

and immediately call you gas supplier or your fire
department.

WARNING

Combustion byproducts produced when using this

product contain chemicals kno wn to the State
of California to cause cancer, birth defects, or

other reproductive harm.

Your grill will get very hot. Never lean over the cooking area while using your grill. Do not touch cooking
surfaces, grill housing, Lid or any other grill parts while the grill is in operation, or until the gas grill has
cooled down after use.

1.Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.

2.An LP cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.

Failure to comply with these instructions could result
in a fire or explosion that could cause serious bodily
injury, death, or property damage.

WARNING

Warning

WARNING

WARNING

Do not try to light this appliance without first reading the “LIGHTING INSTRUCTIONS”
section in this manual.

I21Y06P-2

TABLE OF CONTENTS

SECTION ONE

Table of Contents & Importance
Precautions----------------------------------------1-2
Placement of the Grill--------------------------- 3

SECTION TWO

Assembly Instructions---------------------------4-12
To Match Light The Grill------------------------13
Gas Hook Up----------------------------------- 14-15
Installer Final Check Lis t ------------------------15
Leak Testing------------ ----------------------- 16-17

SECTION THREE

Operating Instruction--------------------------18-19
Grill Lighting Instruction-------------19-22
Lighting Illustration-----------------------------23

SECTION FOUR

Care & Maintenance-------------------24-25

SECTION FIVE

Trouble Shooting-------------------------26-27

Exploded View---------------------------28
Part List -----------------------------------29

Ordering Parts & Grilling Hints ----------30

SECTION SIX

Grill Cooking Chart---------------------31-33

SECTION SEVEN

Grill Recipe Suggestions--------------34-36

SECTION EIGHT

Limited Warranty------------------------37

I21Y06P-2

PRECAUTIONS

WARNING

Do not try to light this appliance without
first reading the “LIGHTING
INSTRUCTIONS” section in this manual.

TESTED IN ACCORDANCE WITH ANS
Z21.58a •CSA 1.6a-2006 STANDARD FOR
OUTDOOR COOKING GAS APPLIANCES.
THIS GRILL IS FOR OUTDOOR USE ONLY.

Check your local building codes for the
proper method of installation. In the
absence of local codes, this unit should be
installed in accordance with the National
Fuel Gas Code ANSI Z223.1/NFPA 54,
OR CSA B149.1 Natural Gas and
Propane Installation Code, and the
National Electrical Code, ANSI/NFPA 70,
or Propane storage and handling code,
B149.2.

CALIFORNIA PROPOSITION 65-WARNING
The burning of gas fuel generates some by-

products, which are on the list of
substances, which are known by the State
of California to cause cancer or
reproductive harm. California law requires
businesses to warn customers of potential
exposure to such substances. To minimize
exposure to these substances, always
operate this unit according to the use and
care manual, ensuring you provide good
ventilation when cooking with gas.

SAFETY PRACTICES TO AVOID PERSONAL
INJURY

When properly cared for, your stainless
steel grill will give safe, reliable service for
many years. However, extreme care must
be used since the grill produces intense
heat and that can increase accident
potential. When using this appliance basic
safety practices must be followed, including
he following:

Read this Care and Use Manual carefully
and completely before using your grill to
reduce the risk of fire, burn hazard or other
injury.

Do not repair or replace any part of the grill
unless specifically recommended in this
manual. All other service should be referred
to a qualified technician.

CHILDREN SHOULD NOT BE LEFT
ALONE OR UNATTENDED IN AN AREA
WHERE THE GRILL IS BEING USED.
NEVER ALLOW THEM TO SIT, STAND
OR PLAY ON OR AROUND THE GRILL
AT ANY TIME.

I21Y06P-2

1

PRECAUTIONS

DO NOT STORE ITEMS OF INTEREST
TO CHILDREN AROUND OR BELOW
THE GRILL OR IN THE CART. NEVER
ALLOW CHILDREN TO CRAWL INSIDE
OF THE CART.

Never let clothing, pot holders or other
flammable materials come in contact with
or too close to any grate, burner or hot
surface until it has cooled. Fabric may
ignite and result in personal injury.

For personal safety, wear proper apparel.
Loose fitting garments or sleeves should
never be worn while using this appliance.
Some synthetic fabrics are highly
flammable and should not be worn while
cooking.

Only certain types of glass, heat-proof
glass ceramic, earthenware, or other
glazed utensils are suitable for grill use.
These types of materials may break with
sudden temperature changes. Use only on
low or medium heat settings according to
the manufacturer’s directions.

Do not heat unopened food containers as
a build-up of pressure may cause the
container to burst.

Use a covered hand when opening the
grill lid. Never lean over an open grill.

WHEN LIGHTING A BURNER, ALWAYS
PAY CLOSE ATTENTION TO WHAT
YOU ARE DOING. BE CERTAIN YOU
ARE TURNING THE IGNITER LABELED
FOR THE BURNER YOU INTEND ON
USING.

When using the grill, do not touch the grill
rack, burner grate or immediate
surroundings as these areas become
extremely hot and could cause burns. Use
only dry potholders.

Moist or damp potholders on hot surfaces
may cause burns from steam. Do not use a
towel or bulky cloth in place of potholders.
Do not let potholders touch hot portions of
the grill rack.

Grease is flammable. Let hot grease cool
before attempting to handle it. Avoid letting
excess grease deposits collect in the
grease tray at the bottom of the grill’s
firebox. Clean often.

DO NOT USE ALUMINUM FOIL TO LINE
THE GRILL RACKS OR GRILL BOTTOM.
This can severely upset combustion air flow
or trap excessive heat in the control area.

For proper lighting and performance of the
burners keep the burner ports clean. It is
necessary to clean them periodically for
optimum performance. The burners will
only operate in one position and must be
mounted correctly for safe operation.

Clean the grill with caution. Avoid steam
burns; do not use a wet sponge or cloth to
clean the grill while it is hot. Some cleaners
produce noxious fumes or can ignite if
applied to a hot surface.

INSECT WARNING!!! Spiders and insects
can nest in the burners of this and any
other grill, and cause the gas to flow
improperly. This is a very dangerous
condition which can cause a fire to occur
behind the valve panel, thereby damaging
the grill and making it unsafe to operate.
Inspect the grill twice a year.

Be sure all grill controls are turned off and
the grill is cool before using any type of
aerosol cleaner on or around the grill. The
chemical that produces the spraying action
could, in the presence of heat, ignite or
cause metal parts to corrode.

2I21Y06P-2

PRECAUTIONS

Do not use the grill for cooking
excessively fatty meats or products which
promote flare-ups. Do not operate the grill
under unprotected combustible
construction. Use only in well ventilated
areas. Do not use in buildings, garages,
sheds, breezeways or other such
enclosed areas. THIS UNIT IS FOR
OUTDOOR USE ONLY.

Keep the area surrounding the grill free
from combustible materials, trash, or
combustible fluids and vapors such as
gasoline or charcoal lighter fluid. Please
check the surrounding area before use.
And keep a minimum of 24”(61cm)
clearance from combustible material. Do
not obstruct the flow of combustion and
ventilation air. Keep the ventilation
openings of the cylinder enclosure free
and clear from debris. This must be
checked before each use. If the unit is
stored indoors ensure that it is cool. If
propane is used, the cylinder must be
unhooked and the propane cylinder stored

outside in a well ventilated area, out of the
reach of children.

DO NOT USE BRIQUETTES OF ANY
KIND IN THE GRILL.

This stainless steel grill is designed for
optimum performance without the use of
briquettes. Do not place briquettes on the
flame tamer as this will block off the area
for the grill burners to vent. Adding
briquettes can damage ignition components
and knobs, and void the warranty.

Keep the back of the cart free and clear
from debris. Keep any electrical supply
cord, or the rotisserie motor cord away
from the heated areas of the grill.

Never use the grill in extremely windy
conditions. If located in a consistently windy
area (oceanfront, mountaintop, etc.) a
windbreak will be required (see below).
Always adhere to the specified clearance.

NEVER USE A DENTED OR RUSTY
PROPANE TANK.

PLACEMENT OF THE GRILL

CLEARANCE
To Non-Combustible Construction
A minimum of 24”(61cm) clearance from the

back of the grill to non-combustible
construction is required for the lid to open
fully.

DO NOT INSTALL THIS UNIT INTO
COMBUSTIBLE ENCLOSURES!

LOCATION
When determining a suitable location take

into account concerns such as exposure to
wind, proximity to traffic paths and keeping
any gas supply lines as short as possible.

Locate the grill only in a well-ventilated area.
Never locate the grill in a building, garage,

breezeway, shed or other such enclosed areas
without an approved ventilation system. During
heavy use, the grill will produce a lot of smoke.
Lock the wheels after the grill is placed in a
suitable position according to the sticker
located behind the right door. Keep any
electrical supply cord and the fuel supply hose
away from any heated surfaces. Storage of an
outdoor gas cooking appliance indoors is
permissible only if the cylinder is disconnected
and removed from the appliance.

This outdoor cooking gas appliance shall be
used only outdoor and shall not be used in a
building, garage or any other enclosed area.
This appliance is not intended to be installed
on or on recreational vehicles and/or boats

3I21Y06P-2

ASSEMBLY INSTRUCTIONS

PLEASE READ THE INSTURCTION CAREFULLY AND FOLLOW STEP
BY STEP

●Propane Tank is not included

●Philips head Screwdriver (not provided)

●The following hardware is provided

Item

1

2

3

4

5

philips head screw

head s cr ew

head s cr ew

head s cr ew

flat washer

1/4

x50mm

x15mm

1/4

3/16

x10mm

5/32x10 mm

1/4

Quanti tySpecificationDes cr i pt i on

8pcs

22pcs

8pcs

2pcs

4pcs

6

7

locking washer

locking

washer

1/4

5/32

26pcs

2pcs

I21Y06P-2

4

ASSEMBLE INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

PLEASE READ THE INSTRUCTIONS CAREFULLY AND FOLLOW STEP
BY STEP.

TOOLS REQUIRED:
(1) PHILIPS HEAD SCREWDRIVER – NOT PROVIDED

STEP 1:

Attach bottom panel to side panel with 4 pieces 1/4x50mm philips head
screws with 4 pieces locking washer as shown figure below.

STEP 2

:

Attach the back panel to the two side panels with 4 pieces 1/4x15mm
philips head screws and 4 pieces 1/4 locking washers, and attach the
gas tank supporting onto the bottom with 4 pieces 1/4x15mm head
screws and 4 pieces 1/4 locking washers.

I21Y06P-2

5

ASSEMBLY INSTRUCTIONS

STEP 3:

Attach 4 pieces swivel casters with brake to the legs of the bottom.
Tighten caster bolts securely using hex nut wrench provided in parts
pack.

STEP4:

Attach door shaft to the outside of cart legs with 4 pieces 1/4x50mm
philips head screws and 4 pieces 1/4 locking washer then using 2
pieces 1/4x15mm head screws and 2 pieces ¼’’ locking washers to
inside of cart legs. Then place the basket into basket brackets of left
side panel.

1/4x50mm

philips head screws

1/4X15mm
head screws

I21Y06P-2

6

ASSEMBLY INSTRUCTIONS

STEP 5:

Remove the grill head unit from carton, place onto cart from above as
shown on diagram (below). And secure to cart frame.
Caution!!! Head unit is heavy, to avoid injury, we strongly recommend 2 or
more people for this step.

STEP 6:

Secure the head unit to cart with 4 pieces 1/4” x 15mm philips head
screws and 4 pieces flat washers as shown on diagram below.

(Note: Remove cooking grids and flame tamers before this step)

I21Y06P-2

7

ASSEMBLY INSTRUCTIONS

STEP 7:

Attach the left door handle using 4pieces 3/16x10mm philips head screws.
Then attach right door handle using 4 pieces 3/16x10mm philips head
screws.

STEP 8:
Attach the hinge pin in bottom of right side door into hole at the bottom
right front cart leg, then align door with right side door bracket. Depress
spring pin located on top edge of door and slide door lomard right side
door bracket until spring pin locks into hole in door bracket.

I21Y06P-2

8

ASSEMBLY INSTRUCTIONS

STEP 9:

•Insert 4pieces ¼’’x15mm philips head screws with 4pieces ¼’’ locking
washers halfway to the right side grill body panel.

•Place side burner assembly keyholes over bolts and slide dowm,then
tighten securely.

•Fasten side burner front panel to grill body with 1pieces 5/32’’x10mm
philips head screws and 1pieces 5/32’’ locking washers.

Igniter wire

STEP 10:

•Insert 4 pieces 1/4x15mm philips head screws with 4 pieces ¼’’ locking
washers halfway to the left side grill body panel.

•Place side table assembly keyholes over bolts and slide dowm,then tighten
securely.

•Fasten side shelf front panel to grill body with 1pieces 5/32’’x10mm philips
head screw and 1 pieces 5/32’’ locking washers.

I21Y06P-2

9