Newport IDP Quick Start Manual

IDP

Process Meter

12172ML-01 Rev. E MQS1866/N/0202

This device is marked with the international caution symbol. It is important to read
the Setup Guide before installing or commissioning this device as it contains
important information relating to safety and EMC.

It is the policy of NEWPORT to comply with all worldwide safety and EMC/EMI
regulations that apply. NEWPORTis constantly pursuing certification of its products to the
European New Approach Directives. NEWPORTwill add the CE mark to every
appropriate device upon certification.

The information contained in this document is believed to be correct but NEWPORT
Electronics, Inc. accepts no liability for any errors it contains, and reserves the right to
alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for,
patient connected applications.

TRADEMARK NOTICE:

,, ,

newportUS.com

,,

, and are trademarks of NEWPORT Electronics, Inc.

TM

®

NEWPORT

®

NEWPORT

®

NEWPORT Electronics, Inc. warrants this unit to be free of defects in materials and
workmanship for a period of one (1) year from the date of purchase. In addition to
NEWPORT’s standard warranty period, NEWPORT Electronics will extend the warranty
period for one (1) additional year if the warranty card enclosed with each instrument is
returned to NEWPORT.

If the unit should malfunction, it must be returned to the factory for evaluation.
NEWPORT’s Customer Service Department will issue an Authorized Return (AR) number
immediately upon phone or written request. Upon examination by NEWPORT, if the unit
is found to be defective it will be repaired or replaced at no charge. NEWPORT’s
WARRANTY does not apply to defects resulting from any action of the purchaser,
including but not limited to mishandling, improper interfacing, operation outside of design
limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit
shows evidence of having been tampered with or shows evidence of being damaged as a
result of excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of
NEWPORT’s control. Components which wear are not warranted, including but not
limited to contact points, fuses, and triacs.

NEWPORT is pleased to of fer suggestions on the use of its various
products. However, NEWPORT neither assumes responsibility for any
omissions or errors nor assumes liability for any damages that result
from the use of its products in accordance with information provided by
NEWPORT, either verbal or written. NEWPORT warrants only that the
parts manufactured by it will be as specified and free of defects.
NEWPORT MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF
ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of
purchaser set forth herein are exclusive and the total liability of
NEWPORT with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall
not exceed the purchase price of the component upon which liability is
based. In no event shall NEWPORT be liable for consequential,
incidental or special damages.

CONDITIONS: Equipment sold by NEWPORT is not intended to be used, nor shall it be
used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear
installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, or
used on humans, or misused in any way, NEWPORT assumes no responsibility as set
forth in our basic WARRANTY / DISCLAIMER language, and additionally purchaser will
indemnify NEWPORT and hold NEWPORT harmless from any liability or damage
whatsoever arising out of the use of the Product(s) in such a manner.

Direct all warranty and repair requests/inquiries to the NEWPORT Customer Service
Department. BEFORE RETURNING ANY PRODUCT(S) TO NEWPORT,
PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM
NEWPORT’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID
PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper
packaging to prevent breakage in transit.

FOR WARRANTY RETURNS, please
have the following information available
BEFORE
contacting NEWPORT:

1. P.O. number under which the product
was PURCHASED,

2. Model and serial number of the
product under warranty, and

3. Repair instructions and/or specific
problems relative to the product.

FOR NON-W

ARRANTY REPAIRS,
consult NEWPORT for current repair
charges. Have the following information
available BEFORE contacting
NEWPORT:

1. P.O. number to cover the COSTof the

repair,

2. Model and serial number of product,

and

3. Repair instructions and/or specific

problems relative to the product.

NEWPORT’s policy is to make running changes, not model changes, whenever an
improvement is possible. This affords our customers the latest in technology and
engineering.

NEWPORT is a registered trademark of NEWPORT Electronics, Inc.

© Copyright 2002 NEWPORT Electronics, Inc. All rights reserved.
This document may not be copied, photocopied, reproduced, translated, or reduced to
any electronic medium or machine-readable form, in whole or in part, without prior
written consent of NEWPORT Electronics, Inc.

PATENT NOTICE:The “Meter Case Bezel Design” is a trademark of NEWPORT
Electronics, Inc., registered in the U.S. This product is covered by one or more of the
following patents: U.S. Pat. No. Des. 336,895, 5,274,577/ Canada 2052599, 2052600/
Italy 1249456, 1250938/ France Brevet No. 91 12756/ Spain 2039150, 2048066/ UK
Patent No. GB2 249 837, GB2 248 954/ Germany DE 41 34398 C2. OTHER
INTERNATIONALPATENTS PENDING.

Return Requests/Inquiries

Warranty/Disclaimer

56

Configuration Mode

The following table lists display prompts that appear
when the meter is in the configuration mode.

MENU

䊳

/TARE

䊱

/MAX

InP 0-10

4-20
20-4
0-5
1-5

dEc.P FFF.F

FFFF.
FFFF
F.FFF
FF.FF

ScAL int rd1*

LivE XXXX

rd 2*
*XXXX

* Shows only if you press the

䊱

/MAX button.

Tare

The following buttons enable tare functions in the run
mode:

T-RST

Clears tare value

䊳

/TARE

Tares display value to zero.

Reference Information

Meter Modes

Run Mode - The meter is in the run mode when the
display is actively showing a process.

Configuration Mode - The meter is in the configuration
mode when you press the MENU button to enable
meter configurations.

Jumpers

The following table gives you information about
jumpers. Refer to the illustration below for exact
jumper location. Refer to the Operator's Manual for
additional jumper information.

S1 - S3 Jumpers

Jumper Description

S1 Installed: 10 V excitation

Removed: 24 V excitation

S2 Installed: Front-panel buttons locked

out Removed: All buttons operable

S3 Installed: PEAK shows when

䊱

/MAX
button is pushed. PrsT (Peak Reset)
is active when RESET is pushed.
Press

䊱

/MAX to show PEAK value.*

Removed: VALLEY shows when

䊱

/MAX button is pushed. VrST
(Valley Reset) is active when
RESET is pushed. Press

䊱

/MAX to

show VALLEY value.*

*Shows in run mode only

S3

S2

S1

For immediate technical or application assistance please call:

Newport Electronics, Inc.

2229 South Yale Street • Santa Ana, CA • 92704 • U.S.A.

TEL: [phone] • FAX: [phone]

Toll Free: 1-800-639-7678 • http://www.newportUS.com • e-mail:[e-mail]

ISO 9001 Certified

Newport Technologies, Inc.

976 Bergar • Laval (Quebec) • H7L 5A1 • Canada

TEL: [phone] • FAX: [phone]

Toll Free: 1-800-639-7678 • http://www.newport.ca • e-mail:[e-mail]

Newport Electronics, Ltd.

One Omega Drive • River Bend Technology Centre

Northbank, Irlam • Manchester M44 5BD • United Kingdom

Tel: [phone] • FAX: [phone]

Toll Free: 0800 488 488 • http://www.newportuk.co.uk • e-mail:[e-mail]

Newport Electronics B.V.

Postbus 8034 • 1180 LA Amstelveen • The Netherlands

TEL: [phone] • FAX: [phone]

Toll Free: 0800 0993344 • http://www.newport.nl • e-mail: [e-mail]

Newport Electronics spol s.r.o.

Rudé armády 1868, 733 01 Karviná 8 • Czech Republic

TEL: [phone] • FAX: [phone]

Toll Free: 0800-1-66342 • http://www.newport.cz • e-mail: [e-mail]

Newport Electronics GmbH

Daimlerstrasse 26 • D-75392 Deckenpfronn • Germany

TEL: [phone] • FAX: [phone]

Toll Free: 0800 / 6397678 • http://www.newport.de • e-mail: [e-mail]

Newport Electronique S.A.R.L.

9, rue Denis Papin • 78190 Trappes • France

TEL: [phone] • FAX: [phone]

Toll Free: 0800-4-06342 • http://www.newport.fr • e-mail: [e-mail]

Mexico and Latin America

TEL: [phone] • FAX: [phone]

En Español: 001 [phone]

7. Press 䊱/MAX. The display momentarily flashes
“rd 1”, then shows the low calibrated value.

8. a. If you selected “int,”enter the desired display

corresponding to low input.

(0Vdc, 1Vdc, 4mA)

b. If you selected “LivE”, apply low load to

sensor and enter desired display.

Press䊱/MAX and 䊳/TARE to enter desired
display.

9. Press MENU. The display momentarily flashes
“rd 2”, then shows the high calibrated value.

10. a. If you selected “int”, enter the desired display

corresponding to high input.
(10Vdc, 5Vdc, 20mA)

b. If you selected “LivE”, apply full scale or 3/4

full scale load to sensor and enter desired
display.

Press䊱/MAX and 䊳/TARE to enter the desired
display.

11. Press MENU to store new scale factor and return
to the run mode.

12. If the display is not zero, with no load on your
sensor, press 䊳/TARE. Scaling is now complete.

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

.

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

Connect the Sensor Input

Depending upon sensor input type, connect your
sensors according to one of the following figures. If
your sensor type is not shown, refer to Section 3 of the
Operator’s Manual.

4 -20 mA Input with External Excitation

3-Wire dc Voltage Input with Internal Excitation

4-20 mA Transmitter with Internal Excitation

Apply Power

Plug in the meter. There is no power switch, so the
meter will be active as soon as you apply power. The
meter shows the following:

* Represents the revision code. Write this number
down. You will need this number if you call Customer
Service for assistance.

J4

1

2

3

J3

2

3

Jumper

User

Provided

2

3

1

2

3

J3

J4

EXC

SIG

COM

J4

1

2

3

START HERE

2

34

Using This Quick Start Manua

l

Use this Quick Start manual with your meter to power
up, configure and scale your meter. For detailed
instructions, refer to the appropriate section in the
Operator’s Manual.

Wiring

1. Locate the J1 connector.

2.

Insert the correct wire in each terminal as shown in
the following figure and tighten the lockdown screws.

3. Tug gently on the wires to verify the connections.

Main Power Connections - ac

Mount the Meter

1. Cut a hole in your panel, as shown in the figure
below.

2. Insert the meter into the hole. Be sure the front
bezel is flush to the panel.

1.772" + .024/–.000

(45.01mm + 0.61/–0.00)

3.622" + .032/–.000

(92.00mm + 0.81/–0.00)

PANEL

Line Neutral

AC Power

123

FUSE

Earth
Ground

J1

Configuring and Scaling Your Meter

1. Press MENU. The meter momentarily shows
“InP”, then shows last saved input range.

2. Configure the input range by pressing 䊳/TARE
to select from the following:
4-20mA, 20-4mA, 0-5V, 1-5V and 0-10V.

3. Press MENU to store range. The meter
momentarily shows “Stor”,“dEc.P”, and then
shows the last saved decimal point location.

4. Configure the decimal point
location by pressing
䊳/TARE to select from the
following: FFF.F, FFFF.,
FFFF, F.FFF and FF.FF.

5. Press MENU to store decimal point. The meter

momentarily shows “Stor”, “ScAL”, and then
shows the last saved scaling method.

6. Press 䊳/TARE to select
“int” or “LivE” scaling. “int”
is internal scaling, or
scaling without known
loads. “LivE” is applying
known loads to a sensor.

...

.

*

T-RST

䊱/MAX

䊳/TARE

MENU

RESET

T-RST

䊱/MAX

䊳/TARE

MENU

RESET

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

T-RST

䊱/MAX

䊳/TARE

MENU

RESET

.

T-RST

䊱/MAX

䊳/TARE

MENU

RESET

.

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

T-RST

䊱/MAX 䊳/TARE

MENU

RESET

Warning: Do not connect AC power to your device
until you have completed all input and output
connections. This device must only be installed by a
specially trained electrician with corresponding
qualifications. Failure to follow all instructions and
warnings may result in injury!