Page 1
GTS30V
G
U
A
R
A
N
T
E
E
D
S
P
E
C
I
F
I
C
A
T
I
O
N
S
High Precision
Vertical Linear Stage
USER’S MANUAL
Page 2
GTS30V High Precision Vertical Linear Stage
Newport Corporation warrants this product to be free from defects in
material and workmanship for a period of 1 year from the date of
shipment. If found to be defective during the warranty period, the product
will either be repaired or replaced at Newport’s discretion.
To exercise this warranty, write or call your local Newport representative,
or contact Newport headquarters in Irvine, California. You will be given
prompt assistance and return instructions. Send the instrument,
transportation prepaid, to the indicated service facility. Repairs will be
made and the instrument returned, transportation prepaid. Repaired
products are warranted for the balance of the original warranty period, or
at least 90 days.
Limitation of Warranty
This warranty does not apply to defects resulting from modification or
misuse of any product or part.
This warranty is in lieu of all other warranties, expressed or implied,
including any implied warranty of merchantability or fitness for a
particular use. Newport Corporation shall not be liable for any indirect,
special, or consequential damages.
by Newport Corporation, Irvine, CA. All rights reserved.
Original instructions.
No part of this document may be reproduced or copied without the prior
written approval of Newport Corporation. This document is provided for
information o nl y, and pro du ct specifications are subject to change without
notice. Any change will be reflected in future publishings.
CAUTION
Warranty does not apply to damages resulting from:
• Incorrect usage:
– Load on the stage greater than maximum specified load.
– Carriage speed higher than specified speed.
–Improper grounding.
¬ Connectors must be properly secured.
¬ When the load on the stage represents an electrical risk, it must
be connected to ground.
– Excessive or improper cantilever loads.
• Modification of the stage or any part thereof.
CAUTION
Please return equipment in
the original (or equivalent)
packing.
You will be responsible for
damage incurred from
inadequate packaging if the
original packaging is not
used.
Warranty
EDH0222En1041 — 12/18 ii
© 2018
Page 3
GTS30V High Precision Vertical Linear Stage
Table of Contents
Warranty .................................................................................................................ii
EC Declaration of Conformity...............................................................................v
Definitions and Symbols.......................................................................................vi
Warnings ...............................................................................................................vii
Caution .................................................................................................................viii
1.0 — Introduction.................................................................................1
2.0 — Description ...................................................................................2
2.1 Design Details ............................................................................................2
3.0 — Characteristics............................................................................3
3.1 Definitions ..................................................................................................3
3.2 Mechanical Specifications .......................................................................4
3.3 Load Specification Definitions.................................................................4
3.4 Load Characteristics and Stiffness .........................................................4
3.5 Stage Weights ............................................................................................5
4.0 — Drive and Motor.........................................................................5
4.1 DC-Servo Drive Version ............................................................................5
4.2 Sensor Position..........................................................................................6
4.3 Feedback Signal Position .........................................................................6
4.4 Pinouts........................................................................................................7
4.5 MCAB-3 Cable ............................................................................................7
5.0 — Connection to Newport Controllers ................................8
5.1 Warnings on Controllers ..........................................................................8
5.2 Connection .................................................................................................9
5.3 Cables .........................................................................................................9
5.4 MCAB-3 Cable ............................................................................................9
6.0 — Connection to Non-Newport Electronics ....................10
6.1 Connections .............................................................................................10
7.0 — Dimensions.................................................................................11
iii EDH0222En1041 — 12/18
Page 4
GTS30V High Precision Vertical Linear Stage
8.0 — Maintenance ..............................................................................12
8.1 Maintenance ............................................................................................12
8.2 Repair .......................................................................................................12
8.3 Calibration ...............................................................................................12
Service Form .........................................................................................................13
EDH0222En1041 — 12/18 iv
Page 5
GTS30V High Precision Vertical Linear Stage
GTS30V
EU Declaration of Conformity
f
ollowing Annex II-1A
of Directive 2006/42/EC on machinery
The manufacturer:
MICRO-CONTROLE Spectra-Physics,
9, rue du bois sauvage
F-91055 Evry FRANCE
Hereby declares that the machinery:
y Description: " GTS30V"
y Function: High Precision Vertical Linear Stage
y Models: GTS30V
– the technical file of which was compiled by:
Mr Hervé LE COINTE , Quality Director,
MICRO-CONTROLE Spectra-Physics, Zone Industrielle - B.P.29
F-45340 Beaune La Rolande France
– complies with all the relevant provisions of the Directive 2006/42/EC on machinery.
– complies with all the relevant provisions of the Directive 2014/30/EU relating to electromagnetic compatibility.
– complies with all the relevant provisions of the Directive 2011/65/EU relating to RoHS2.
– was designed and built in accordance with the following harmonised standards:
y NF EN 61326-1:2013 « Electrical equipment for measurement, control and
laboratory use – EMC requirements – Part 1: General requirements »
y NF EN 55011:2010/A1:2011 Class A
– was designed and built in accordance with the following other standards:
y NF EN 61000-4-2
y NF EN 61000-4-3
y NF EN 61000-4-4
y NF EN 61000-4-5
y NF EN 61000-4-6
ORIGINAL DECLARATION
Done in Beaune La Rolande on 16 May 2017
Hervé LE COINTE
Quality Director
DC1-EN rev:A
EC Declaration of Conformity
v EDH0222En1041 — 12/18
Page 6
GTS30V High Precision Vertical Linear Stage
The following terms and symbols are used in this documentation and also
appear on the product where safety-related issues occur.
General Warning or Caution
The exclamation symbol may appear in warning and caution tables in this
document. This symbol designates an area where personal injury or
damage to the equipment is possible.
The following are definitions of the Warnings, Cautions and Notes that may
be used in this manual to call attention to important information regarding
personal safety, safety and preservation of the equipment, or important
tips.
WA RN IN G
Warning indicates a potentially dangerous situation which can result in
bodily harm or death.
CAUTION
Caution indicates a potentially hazardous situation which can result in
damage to product or equipment.
NOTE
Note indicates additional information that must be considered by the
user or operator.
European Union CE Mark
The presence of the CE Mark on Newport Corporation equipment means
that it has been designed, tested and certified as complying with all
applicable European Union (CE) regulations and recommendations.
Warnings and Cautions
ATTENTIO N
This stage is a Class A device. In a residential environment, this device
can cause electromagnetic interference. In this case, suitable measures
must be taken by the user.
Definitions and Symbols
EDH0222En1041 — 12/18 vi
Page 7
GTS30V High Precision Vertical Linear Stage
W
ARNING
The motion of objects of all types carries potential risks for operators.
Ensure the protection of operators by prohibiting access to the dangerous
area and by informing the personnel of the potential risks involved.
WA RN IN G
Do not use this stage when its motor is emitting smoke or is unusually
hot to the touch or is emitting any unusual odor or noise or is in any
other abnormal state.
Stop using the stage immediately, switch off the motor power and then
disconnect the electronics power supply.
After checking that smoke is no longer being emitted contact your
Newport service facility and request repairs. Never attempt to repair the
stage yourself as this can be dangerous.
WA RN IN G
Make sure that this stage is not exposed to moisture and that liquid does
not get into the stage.
Nevertheless, if any liquid has entered the stage, switch off the motor
power and then disconnect the electronics from power supply.
Contact your Newport service facility and request repairs.
WA RN IN G
Do not insert or drop objects into this stage, this may cause an electric
shock, or lock the drive.
Do not use this stage if any foreign objects have entered the stage.
Switch off the motor power and then disconnect the electronics power
supply.
Contact your Newport service facility for repairs.
WA RN IN G
Do not place this stage in unstable locations such as on a wobbly table or
sloping surface, where it may fall or tip over and cause injury.
If this stage has been dropped or the case has been damaged, switch off
the motor power and then disconnect the electronics power supply.
Contact your Newport service facility and request repairs.
WA RN IN G
Do not attempt to modify this stage; this may cause an electric shock or
downgrade its performance.
WA RN IN G
Do not exceed the usable depth indicated on the mounting holes (see
section “Dimensions”). Longer screws can damage the mechanics or
cause a short-circuit.
Warnings
vii EDH0222En1041 — 12/18
Page 8
GTS30V High Precision Vertical Linear Stage
C
AUTION
Do not place this stage in a hostile environment such as X-Rays, hard
UV,… or in any vacuum environment.
CAUTION
Do not place this stage in a location affected by dust, oil fumes, steam or
high humidity. This may cause an electric shock.
CAUTION
Do not leave this stage in places subject to extremely high temperatures
or low temperatures. This may cause an electric shock.
• Operating temperature: +10 to +35 °C
• Storage temperature: -10 to +40 °C (in its original packaging)
CAUTION
Do not move this stage if its motor power is on.
Make sure that the cable to the electronics is disconnected before
moving the stage. Failure to do so may damage the cable and cause an
electrical shock.
CAUTION
Be careful that the stage is not bumped when it is being carried. This
may cause it to malfunction.
CAUTION
When handling this stage, always unplug the equipment from the power
source for safety.
CAUTION
When the carriage is in its end-of-run position, it is strongly recommended
not to go beyond this point as this may damage the stage mechanism.
CAUTION
Contact your Newport service facility to request cleaning and
specification control every year.
Caution
EDH0222En1041 — 12/18 viii
Page 9
GTS30V High Precision Vertical Linear Stage
High Precision Vertical Linear Stage
GTS30V
1.0 —Introduction
This manual provides operating instructions for the GTS30V precision
vertical linear stage.
GTS30V stage.
RECOMMENDATION
We recommend you read carefully the chapter “Connection to
electronics” before using the GTS30V stage.
ILS250, GTS30V and URS100 stages
in XZθz configuration.
1 EDH0222En1041 — 12/18
Page 10
GTS30V High Precision Vertical Linear Stage
2.0 —Description
The GTS30V is the ideal foundation for applications that require long
ravel vertical motion of horizontally oriented samples. Its low profile and
t
high-precision motion capabilities make this stage an excellent choice for
applications such as semiconductor wafer inspection, nanotechnology,
automated device alignment, metrology, and quality control processes.
When combined with our XM, GTS, VP, ILS, or IMS series of linear stages,
he GTS30V is a space-saving alternative to traditional XYZ stacks of
t
stages, and provides unobstructed access to the payload from any side.
Furthermore, centering the payload over the bearings, ensures less
cantilevering load effects and Abbe induced motion errors.
High-precision vertical motion is achieved using a direct vertical guiding
system composed of matched pairs of anti-creep crossed roller bearings.
Compared to alternative wedged designs, this direct guiding method
provides consistently lower and more repeatable runout errors. In
addition, the lack of any re-circulating elements in the bearings leads to
outstanding ripple-free motion required in high-sensitivity focus
adjustments. Lastly, the geared retainers prevent bearing cage migration, a
problem often found with other linear bearings, especially in vertical
arrangements.
A folded DC motor with a precision ground, low friction lead screw
arrangement delivers ultra-smooth motion and does not back drive even at
high loads. A reduction belt between the motor and the lead screw
increases the available output torque, reduces the servo sensitivity and
ensures 100 nm minimum incremental motion with all Newport motion
controllers and drivers.
Precision position feedback is provided by an optical scale with 50 nm
resolution. Compared to alternative designs featuring a screw mounted
rotary encoder, this direct position feedback avoids drive train errors
impacting positioning performance, hence leading to superior positioning
accuracy and repeatability.
2.1 Design Details
Base Material High-strength 7075 Aluminum
Bearings Anti-creep crossed roller bearings
Drive Mechanism Precision ground lead screw, gravity preloaded nut
Drive Screw Pitch 1 mm
Feedback Linear steel scale, 20 µm signal period, 0.05 µm resolution,
RS-422 differential output
Limit Switches Optical
Origin Optical, located 5 mm from lower position travel limit
Drive Type DC Servo
Cable Length 3 m (included)
EDH0222En1041 — 12/18 2
Page 11
GTS30V High Precision Vertical Linear Stage
Specifications of our products are established in reference to ISO 230
standard part II “Determination of accuracy and repeatability of
positioning numerically controlled axes”.
T
his standard gives the definition of position uncertainty which depends
on the 3 following parameters:
Absolute Accuracy
Difference between ideal position and real position.
Accuracy
Difference between ideal position and real position after the compensation
of linear errors.
Linear errors include: cosine errors, inaccuracy of screw or linear scale
pitch, angular deviation at the measuring point (Abbe error) and thermal
expansion effects. All Newport motion electronics can compensate for
linear errors.
The relation between absolute accuracy and on-axis accuracy is as follows:
Absolute Accuracy = Accuracy + Correction Factor
x Travel
Repeatability
Ability of a system to achieve a commanded position over many attempts.
Reversal Value (Hysteresis)
Difference between actual position values obtained for a given target
position when approached from opposite directions.
Minimum Incremental Motion (MIM or Sensitivity)
The smallest increment of motion a device is capable of delivering
consistently and reliably.
Resolution
The smallest increment that a motion device can theoretically move
and/or detect. Resolution is not achievable, whereas MIM, is the real
output of a motion system.
Yaw, Pi tch
Rotation of carriage around the Z axis (Yaw) or Y axis (Pitch), when it
moves.
The testing of accuracy, repeatability, and reversal error are made
systematically with test equipment in controlled environment (20±1°C).
A linear cycle with 21 data points on the travel and 4 cycles in each
direction gives a total of 168 points.
Guaranteed and Typical Specifications
Guaranteed maximum performance values are verified per Newport's A167
metrology test procedure. For more information, please consult the
metrology tutorial section in the Newport catalog or at www.newport.com
3.0 —Characteristics
3.1 Definitions
3 EDH0222En1041 — 12/18
Page 12
GTS30V High Precision Vertical Linear Stage
G
U
A
R
A
N
T
E
E
D
S
P
E
C
I
F
I
C
A
T
I
O
N
S
k
α
z
k
α
x
k
α
y
X
Y
Z
Q
D
C
z
.
5
1
(
1
3
)
.
7
5
(
1
9
)
3.2 Mechanical Specifications
Travel Range (mm) 30 (-5/+25 from origin)
Minimum Incremental Motion (µm) 0.1
Bi-directional Repeatability, Typical (Guaranteed)
Accuracy, Typical (Guaranteed)
(1)
(µm) ±0.37 (±0.75)
(1)
(µm) ±0.07 (± 0.10)
Maximum Speed (mm/s) 10
Straightness, Flatness
Pitch, Typical (Guaranteed)
Roll, Typical (Guaranteed)
(1)
(µm) 1.5 or ± 0.75
(1) (2)
(µrad) ±20 (±25)
(1) (2)
(µrad) ±12 (±25)
MTBF (h) 20,000 hours at 25% load and with a 30% duty cycle
1)
Shown are peak to peak, guaranteed specifications or ±half the value as sometimes shown. For the definition of
typical specifications which are about 2X better than the guaranteed values, visit www.newport.com for the
Motion Control Metrology Primer.
2)
To obtain arcsec units, divide µrad value by 4.8.
CAUTION
To reach specifications stated, stages must be fixed on a plane surface
with a flatness of 5 µm.
3.3 Load Specification Definitions
Normal Load Capacity (Cz)
Maximum load a stage can move while maintaining specifications.
Max. Speed (mm/s) 10
Max. Acceleration (mm/s2) 40
3.4 Load Characteristics and Stiffness
Cz, Normal centered load capacity (N) 40
Kax, Compliance in roll (µrad/Nm) 40
Kay, Compliance in pitch (µrad/Nm) 40
Kaz, Compliance in yaw (µrad/Nm) 25
Qx Qy, Off-center load (N) Q ≤ Cz ÷ (1 + D/30)
Where D
= Cantilever distance (mm) 100
max.
CAUTION
Do not use the GTS30V stage as an horizontal movement. Specifications
EDH0222En1041 — 12/18 4
are given only for a vertical use (gravity preloaded).
Page 13
GTS30V High Precision Vertical Linear Stage
Direction +
+V
+ Motor
– Motor
–V
MOTION Direction +
MOTIONDirection –
3.5 Stage Weights
The stage weight indicated into the below table is the one of the stage
ithout any cable.
w
Weight [lb (kg)]
GTS30V 7.3 (3.3)
3-meter MCAB-3 Cable 1.32 (0.6)
4.0 —Drive and Motor
4.1 DC-Servo Drive Version
The GTS30V stage is equipped with a DC-motor and a metal optical scale.
DC-Motor Performance Specifications and Characteristics
Resolution Speed Nominal Max RMS Max. Peak Resistance Inductance Tachometer
(µm) (mm/s) Voltage (V) Current (A) Current (A) (Ω) (mH) Const. (V/krpm)
GTS30V 0.05 10 48 0.5 1.0 2.52 0.51 –
Command Signals for the DC-Motor
In the above drawings, + Motor signal is referred to – Motor signal.
When the stage moves in + Direction, the + Motor voltage is higher than
➀
– Motor voltage.
When the stage moves in – Direction, the + Motor voltage is lower than
➁
5 EDH0222En1041 — 12/18
– Motor voltage.
Page 14
GTS30V High Precision Vertical Linear Stage
S
tage Travel Range
Home Position (Origin)
at 5 mm from the bottom end of travel
Motion Direction +
–
EOR Limit
M
echanical
Z
ero
I
ndex Pulse
I
ndex Pulse
+ EOR Limit
0
1
E
ncoder
P
hase A
0
1
Encoder
Phase A
1
234
0
1
Encoder
Phase B
0
1
Encoder
Phase B
Direction – MOTION Direction +
Direction +
SUD-D25 OR SUB-D15
Encoder Phase A 19 13
Encoder Phase A 23 6
Encoder Phase B 20 14
Encoder Phase B 24 7
Index Pulse Phase I 15 15
Index Pulse Phase I 25 8
21 12
22 5
NEWPORT
STAGE
USER
CONNECTOR PIN #
Output Signals
Encoders
& Sensors
Power Supply
+5 V 5%
150 mA max.
0 V
}
4.2 Sensor Position
End-of-Run and Mechanical Zero are 5 V open collector type.
The Index Pulse provides a repeatable Home Position at ±1 step.
CAUTION
“End-of-Run” and “Mechanical Zero” are active signals and should not be
connected to any other source.
4.3 Feedback Signal Position
The incremental sensor consists of an optical scale and an encoder head.
When the carriage moves, the encoder head generates square signals in
quadrature and sends to pins #19, #20, #23 and #24 of the SUB-D25
connector.
EDH0222En1041 — 12/18 6
“Encoder” and “Index Pulse” are “differential pair” (type RS-422) type
output signals. Using these signals permits a high immunity to noise.
Page 15
GTS30V High Precision Vertical Linear Stage
1
3
2
5
1
4
1
CONNECTED
CONNECTED
SUB-D25M
CONNECTOR
1
2
3
4
5
6
7
8
14
22
21
16
19
23
20
24
15
25
17
18
13
SUB-D25F
CONNECTOR
1
2
3
4
5
6
7
8
14
22
21
16
19
23
20
24
15
25
17
18
13
(0.6 MM2) WHITE 1
(0.6 MM
2
) WHITE 2
(0.6 MM2) WHITE 3
(0.6 MM2) WHITE 4
(0.6 MM2) WHITE 6
(0.6 MM2) WHITE 7
(0.6 MM2) WHITE 8
(0.6 MM2) WHITE 9
(0.6 MM2) WHITE 5
(0.6 MM2) WHITE 10
(0.6 MM2) WHITE 11
(0.6 MM2) WHITE 12
(0.09 MM2) WHITE
(0.09 MM2) BROWN
(0.09 MM2) GREEN
(0.09 MM2) YELLOW
(0.09 MM2) GREY
(0.09 MM2) PINK
(0.09 MM2) BLUE
(0.09 MM2) RED
(0.09 MM2) BLACK
(0.09 MM2) PURPLE
(0.09 MM2) ORANGE
(0.09 MM2) BLUE
(AWG20) WHITE 1
(AWG20) WHITE 2
(AWG20) WHITE 3
(AWG20) WHITE 4
(AWG20) WHITE 6
(AWG20) WHITE 7
(AWG20) WHITE 8
(AWG20) WHITE 9
(AWG20) WHITE 5
(AWG20) WHITE 10
(AWG20) WHITE 11
(AWG20) WHITE 12
(AWG28) WHITE
(AWG28) BROWN
(AWG28) GREEN
(AWG28) YELLOW
(AWG28) GREY
(AWG28) PINK
(AWG28) BLUE
(AWG28) RED
(AWG28) BLACK
(AWG28) PURPLE
(AWG28) ORANGE
(AWG28) BLUE
Emission circuits generally used by Newport are 26LS31 or MC3487.
Reception circuits to use are 26LS32 or MC3486.
4.4 Pinouts
The pinout diagram for the GTS30V stage SUB-D25M connector is shown
below.
IMS-V
1 N.C.
2 N.C.
3 N.C.
4 N.C.
5 + Motor
6 + Motor
7 – Motor
8 – Motor
9 N.C.
10 N.C.
11 N.C.
12 N.C.
13 Mechanical Zero
14 Ground
15 Index Pulse I
16 0 V
17 + End-of-Run
18 – End-of-Run
19 Encoder Phase A
20 Encoder Phase B
21 +5 V
22 0 V
23 Encoder Phase /A
24 Encoder Phase /B
25 Index Pulse /I
4.5 MCAB-3 Cable
A 3-meter MCAB-3 cable is supplied with each GTS30V stage (see section
5.5: ”Cables”).
7 EDH0222En1041 — 12/18
Page 16
GTS30V High Precision Vertical Linear Stage
Controllers are intended for use by qualified personnel who recognize
shock hazards and are familiar with safety precautions required to avoid
p
ossible injury. Read the controller user’s manual carefully before
operating the instrument and pay attention to all written warnings and
cautions.
WA RN IN G
Disconnect the power plug under the following circumstances:
• If the power cord or any attached cables are frayed or damaged in
any way.
• If the power plug is damaged in any way.
• If the unit is exposed to rain, excessive moisture, or liquids are spilled
on the unit.
• If the unit has been dropped or the case is damaged.
• If you suspect service or repair is required.
• Whenever you clean the electronics unit.
CAUTION
To protect the unit from damage, be sure to:
• Keep all air vents free of dir t and dust.
• Keep all liquids away from the unit.
• Do not expose the unit to excessive moisture (85% humidity).
• Read this manual before using the unit for the first time.
WA RN IN G
All attachment plug receptacles in the vicinity of this unit are to be of
the grounding type and properly polarized.
Contact your electrician to check your receptacles.
WA RN IN G
This product is equipped with a 3-wire grounding type plug.
Any interruption of the grounding connection can create an electric
shock hazard.
If you are unable to insert the plug into your wall plug receptacle,
contact your electrician to perform the necessary alterations to ensure
that the green (green-yellow) wire is attached to ear th ground.
WA RN IN G
This product operates with voltages that can be lethal.
Pushing objects of any kind into cabinet slots or holes, or spilling any
liquid on the product, may touch hazardous voltage points or short out
parts.
5.0 —Connection to Newport Controllers
5.1 Warnings on Controllers
EDH0222En1041 — 12/18 8
Page 17
GTS30V High Precision Vertical Linear Stage
C
ABLE
C
ONNECTOR
STAGE
L
OCKING
K
NOBS
BENDING
STATIC CABLE: ≥1.50 (38)
CABLE IN MOTION: ≥3.78 (96)
2
.28 (58)
D
ISCONNECTED
ø.39
(10)
SUB-D25 CONNECTOR SHOWN
DIMENSIONS IN INCHES (AND MILLIMETERS)
WA RN IN G
This cable is shielded correctly. For a correct operation, make sure to
lock connectors (ground continuity provided by the cable).
For applications where the standard 3-meter cable (MCAB-3) included with
your stage is not adequate, Newport offers longer length cables designed to
ensure the integrity of your positioning application.
These cables are specially shielded and terminated with Newport’s standard
SUB-D25 connectors. They are available in 5-m (MCAB-5), 7-m (MCAB-7) or
10-m (MCAB-10) lengths.
WA RN IN G
Keep the motor cables at a safe distance from other electrical cables in
your environment to avoid potential cross talk.
5.2 Connection
There is a label on every stage indicating its part and serial numbers.
ARNING
W
Always turn the controller's power OFF before connecting to a stage.
NOTE
These stages are ESP compatible. Enhanced System Performance is
Newport's exclusive technology that enables Newport ESP motion
controllers to recognize the connected Newport ESP stage and upload
the stage parameters. This ensures that the user can operate the motion
system quickly and safely.
5.3 Cables
The GTS30V stage is delivered with a MCAB-3 3-meter cable with a
SUB-D25M connector for direct connection to Newport Controllers.
5.4 MCAB-3 Cable
9 EDH0222En1041 — 12/18
Page 18
GTS30V High Precision Vertical Linear Stage
Iin max.: 16 mA
V
max.: 5.25 V
N
EWPORT
S
TAGE
5.6 V
6.0 —Connection to Non-Newport Electronics
6.1 Connections
WARNING
ewport is not responsible for malfunction or damage of GTS30V stages
N
when used with non-Newport controllers.
WARNING
Newport guarantees
“”compliance of GTS30V stages only if used
with Newport cables and controllers.
It is the customer’s responsibility to modify the cable and take care of
sensor signal connections, when using the stage with non-Newport
controllers.
End-of-Runs and Mechanical Zero are open collector type with a 5.6 V
protective Zener diode.
EDH0222En1041 — 12/18 10
Page 19
GTS30V High Precision Vertical Linear Stage
.97
(24.75)
.39
(10)
(130
+25
)
-5
5.12
+.98
-.20
S
QR 4.53
(
115)
SQ 4.57
(116)
4
.63
(
117.5)
S
QR 3.97
(
100.8)
M
ANUAL KNOB
4 HOLES M6 THD
ON SQR 3.97 (100.8)
DEPTH: .39 (10)
4 HOLES M4 THD
ON 2.95 x 3.94 (75 x 100)
DEPTH: .31 (8)
5
HOLES M4 THD
O
N ø3.62 (Ø 92)
D
EPTH: .31 (8)
SUB-D25M
CONNECTOR
120°
5
°
4 HOLES M6 THD
ON SQR 2.95 (75)
DEPTH: .39 (10)
4 HOLES M4 THD
ON 3.94 x 2.95 (100 x 75)
DEPTH: .31 (8)
4 HOLES ø.31 (Ø 7.8)
DIMENSIONS IN INCHES (AND MILLIMETERS)
7.0 —Dimensions
A compact XYZ assembly consisting of a GTS150 linear stage,
a GTS70 linear stage and a GTS30V vertical stage.
11 EDH0222En1041 — 12/18
Page 20
GTS30V High Precision Vertical Linear Stage
8.0 —Maintenance
ECOMMENDATION
R
Please contact Technical Sales Support team for recommendations on
application specific maintenance.
8.1 Maintenance
The GTS30V stage requires no particular maintenance. Nevertheless, this
is a precision mechanical device that must be kept and operated with
caution.
PRECAUTIONS
The GTS30V stage must be used or stocked in a clean environment,
without dust, humidity, solvents or other substances.
It is recommended to return the stage to Newport for re-lubrication after
2000 hours of use.
If the GTS30V stage is mounted on a workstation and cannot be easily
removed, please contact Newport's After Sales Service for further
instructions.
8.2 Repair
Never attempt to disassemble a component of the stage that has not
been covered in this manual.
To disassemble a non specified component can cause a malfunction of
the stage.
If you observe a malfunction in your stage, please contact us immediately
to arrange for a repair.
RECOMMENDATION
CAUTION
CAUTION
Any attempt to disassemble or repair a stage without prior
authorization will void your warranty.
8.3 Calibration
It is recommended to return your GTS30V stage to Newport once a year
for recalibration to its original specifications.
EDH0222En1041 — 12/18 12
CAUTION
Page 21
Your Lo ca l R ep re se nt at iv e
Tel. :
F
ax:
N
ame:
Company:
Address:
Country:
P. O . N u m b e r :
Item(s) Being Returned:
Model #:
Description:
Reasons of return of goods (please list any specific problems):
R
eturn authorization #:
(Please obtain prior to return of item)
Date:
Phone Number:
Fax Number:
Serial #:
Service Form
13 EDH0222En1041 — 12/18
Page 22
Visit Newport Online at:
North America & Asia
Newport Corporation
1791 Deere Ave.
Irvine, CA 92606, USA
Sales
Tel.: (800) 222-6440
e-mail: sales@newport.com
Technical Support
Tel.: (800) 222-6440
e-mail: tech@newport.com
Service, RMAs & Returns
Tel.: (800) 222-6440
e-mail: service@newport.com
Europe
MICRO-CONTROLE Spectra-Physics S.A.S
9, rue du Bois Sauvage
91055 Évry CEDEX
France
Sales & Technical Support
Tel.: +33 (0)1.60.91.68.68
e-mail: france@newport.com
Service & Returns
Tel.: +33 (0)2.38.40.51.55
www.newport.com
Loading...