New Buck Corporation GAS STOVE HEATER User Manual

CAST STOVE SERIES
(VENT-FREE) NATURAL OR L.P. (LIQUID PROPANE) GAS STOVE HEATER
OWNER’S OPERATION AND INSTALLATION MANUAL
“This appliance is intended for supplemental heating.” “This heater shall not bathroom.”
be installed in a bedroom or
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not use
any phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the
fire department. — Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
WARNING: The MA series vent-free gas log heater is
only approved for use in the CVF(*) series cast iron stove models. (*) Indicates Color Suffix Designation)
WARNING: Improper installation, adjustment,
alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency, or the gas supplier.
WARNING: This is an unvented gas-fired heater. It
uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation section on page 3 of this manual.
This appliance may be installed in an aftermarket*, permanently located, manufactured (mobile) home, where not prohibited by state or local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
NEW BUCK CORPORATION WARNING: Only New Buck Corporation P.O. BOX 69 approved blower assembly, part number 8000 HWY. 226 SOUTH MA CVF714, may be used with the Townsend II SPRUCE PINE N.C. 28777 Revised 03/2003 unit only.
TABLE OF CONTENTS
SAFETY INFORMATION ........................................................................................... 1
AIR FOR COMBUSTION AND VENTILATION ................................................... 3
INSTALLATION / CLEARANCES ............................................................................. 6
STOVE CAVITY ASSEMBLY ................................................................................... 7
INSTALLATION: MODEL (MA C100BATLP OR MA C100BATNAT) BURNER
BASE .............................................................................................................................. 9
POSITIONING OF LOGS ........................................................................................... 10
INSTALLATION: MODEL BVFBX201 (MA CVF200LP OR MA CVF200NAT)
FIRE BOX .................................................................................................................... 11
INSTALLATION: OPTIONAL BLOWER ASSEMBLY .......................................... 13
CONNECTING TO GAS SUPPLY ............................................................................. 14
LIGHTING INSTRUCTIONS (SIT) MILLIVOLT .................................................... 17
CLEANING .................................................................................................................. 19
TROUBLE SHOOTING .............................................................................................. 20
ACCESSORIES ........................................................................................................... 23
REPLACEMENT PARTS ........................................................................................... 24
WIRING DIAGRAM ................................................................................................... 33
WARRANTY ............................................................................................................... 34
IDENTIFICATION NUMBERS AND DESCRIPTIONS FOR CAST STOVE SERIES
HEPPLEWHITE CAST UNIT:
ID # DESCRIPTION CVF100A ALMOND CVF100B BLACK CVF100BP CAST (BLACK PAINT) CVF100G GREEN CVF100GP CAST (GREEN PAINT) CVF100R RED
TOWNSEND II CAST UNIT
ID#___________________________ DESCRIPTION CVF200A ALMOND CVF200B BLACK CVF200BP CAST (BLACK PAINT) CVF200G GREEN CVF200GP CAST (GREEN PAINT) CVF200R RED
BURNER BASE UNITS FOR HEPPLEWHITE CAST UNIT ONLY:
ID# DESCRIPTION MA C100BATLP LIQUID PROPANE MA C100BATNAT NATURAL
BURNER BASE (VENTLESS FIREBOX) UNITS FOR TOWNSEND II ONLY:
ID# DESCRIPTION CVFB200LP LIQUID PROPANE CVFB200NAT NATURAL
OPTIONAL BLOWER ASSEMBLY FOR (VENTLESS FIREBOX) TOWNSEND II ONLY:
ID# DESCRIPTION MA CVF714 BLOWER ASSEMBLY
VENT-FREE NATURAL OR L.P GAS STOVE HEATER
1
SAFETY INFORMATION
WARNINGS
IMPORTANT: Read this
owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.
DANGER: Carbon monoxide poisoning may lead to death!
Carbon Monoxide Poisoning:
Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness, or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol, and those at high altitudes.
Make certain you read and understand all Warnings. Keep this manual for reference. It is your guide to safe and proper operation of this heater.
WARNING: Any change to this heater or its controls can be dangerous.
WARNING: Do not allow fans to blow directly into the stove. Avoid any drafts that alter burner flame patterns. Ceiling fans can create drafts that alter burner flame patterns. Altered burner patterns can cause sooting.
WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
Do not place clothing or other flammable material on or near the appliance. Never place any objects on the heater.
Stove becomes very hot when running heater. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Stove will remain hot for a time after shutdown. Allow surfaces to cool before touching.
Carefully supervise young children when they are in the room with heater. When using the handheld remote accessory, keep selector switch in the OFF position to prevent children from turning on burners with remote.
Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.
2. If you smell gas
shut off gas supply
do not try to light any appliance
do not touch any electrical
switch: do not use any phone in your building
immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions
if you cannot reach your gas supplier, call the fire department
3. This heater shall not be installed in a bedroom or bathroom.
4. Do not use this stove as a wood burning fireplace. Use only models MA C100BATLP, MA C100BATNAT, MA CVFB200LP, or MA CVFB200NAT series vent-free gas log heater.
5. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause sooting.
6. During initial operation, slight smoking could occur due to heater burning manufacturing residues.
7. To prevent the creation of soot, follow the instructions in “Cleaning and Maintenance”, page 19.
8. Before using furniture polish, wax, carpet cleaners, or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.
9. This heater has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available. See “Air for Combustion and Ventilation”, pages 3 through 5. If heater keeps shutting off, see “Trouble­shooting”, pages 20 through 22.
10. Do not run heater
where flammable liquids or vapors are used or stored
under dusty conditions
11. Do not use this stove to cook food or burn paper or other objects.
12. Do not use heater if any part has been exposed to or under water. Immediately call a qualified service technician to inspect the room heater and to replace any part of the control system and any gas control which has been under water.
13. Do not operate heater if any log is broken.
14. Turn heater off and let cool before servicing. Only a qualified service person should service and repair heater.
15. Operating heater above elevations of 4,500 feet could cause pilot outage.
16. Do not place stove directly on carpeting, vinyl tile, or any combustible material other than wood. The stove must set on a metal or wood panel extending the full width and depth of the appliance.
PRODUCT
2
INDENTIFICATION
MODELS MA C100BATLP, MA C100BATNAT OR MA CVFB200LP, MA CVFB200NAT MILLIVOLT LOG HEATER UNITS WITH CVF100’s AND CVF200’s CAST STOVE SERIES.
STOVE BODY
STOVE DOOR
(SHOWN IN THE OPEN POSITION)
OPTIONAL
REMOTE CONTROL BRACKET
PIEZO IGNITOR
AUTO OFF MANUAL
PRESSURE ADJUSTMENT (FLAME) KNOB
VALVE CONTROL KNOB
FIGURE 1– TYPICAL STOVE CABINET MODEL
LOCAL CODES
Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition of “The National Fuel Gas Code ANSI Z223.1”, also know as NFPA 54*.
*Available from:
American National Standards Institute Inc. 1430 Broadway New York, NY 10018 National Fire Protection Association, Inc. Batterymarch Park Quincy, MA 02269
PRODUCT FEATURES
OPERATION
This heater is clean burning. It requires no outside venting. There is no heat loss out a vent or up a chimney. Heat is generated by realistic, dancing yellow flames. This heater is designed for vent
-free operation. State and local codes in some areas prohibit the use of vent­free heaters.
SAFETY PILOT
This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room heaters. The ODS/pilot shuts off the heater if there is not enough fresh air.
PIEZO IGNITION SYSTEM
This heater has a piezo ignitor. This system requires no matches, batteries, or other sources to light heater.
3
AIR FOR COMBUSTION AND VENTILATION
WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for ade-quate combustion and ventilation air. Read the following instructions to ensure proper fresh air for this and other fuel-burning appliances in your home.
Today’s homes are built more energy effi­cient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.
While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.
Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances.
PROVIDING ADEQUATE VENTILATION
The following are excerpts from
National Fuel Gas Code, NFPA 54/ ANSI Z223.1, Section 5.3, Air for Combustion and Ventilation.
All spaces in homes fall into one of the three following ventilation classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 4 through 5 will help you classify your space and provide adequate ventilation.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.
Unusually tight construction is defined as construction where: a Walls and ceilings exposed to
the outside atmosphere have a continuous water vapor re­tarder with a rating of one perm (6 x 10
2
) or less with openings
m gasketed or sealed and
b Weather stripping has been
added on openable windows and doors and
c Caulking or sealants are
applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings.
If your home meets all of the three criteria above, you must provide additional fresh air. See Ventilation Air From Outdoors, page 5.
If your home does not meet all of the three criteria above, proceed to
Determining Fresh-Air Flow For Heater Location, page 4.
-11
kg per pa-sec-
Confined and Unconfined Space
The National Fuel Gas Code, ANSI Z223.1 defines a confined space as a
space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8
3
per kw) of the aggregate input
m rating of all appliances installed in that space; and unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8
3
per kw) of the aggregate input
m rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconfined space.
This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air.
*Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.
Installation and repair should be done by a qualified service person. The appliance should be inspected before each use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, pet hair, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.
WARNING: Any change to
this heater or its controls can be dangerous.
AIR FOR
4
COMBUSTION AND VENTILATION
Continued
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have A Confined or Unconfined Space
Use this work sheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.
1. Determine the volume of the space (length x width x height). Length x Width x Height = ____________________ cu. Ft. (volume of space) Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. Ft. (volume of space) if additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support. ____________________ (volume of space) / 50 cu. Ft. = (maximum Btu/Hr the space can support) Example: 2560 cu. Ft. (volume of space) / 50 cu. Ft. = 51,200 (maximum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space. Vent-free heater ________________ Btu/Hr Gas water heater* ________________ Btu/Hr Gas furnace ________________ Btu/Hr Example: Vented gas heater ________________ Btu/Hr Gas water heater 40,000 Btu/Hr Gas fireplace logs ________________ Btu/Hr Vent-free heater + 30,000 Btu/Hr Other gas appliances* + ________________ Btu/Hr Total = 70,000 Btu/Hr Total = ________________ Btu/Hr
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used. ______________ Btu/Hr (maximum the space can support) ______________ Btu/Hr (actual amount of Btu/Hr used) Example: 51,200 Btu/Hr (maximum the space can support) 70,000 Btu/Hr (actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows: A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined
space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 5.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 5. C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no additional fresh air ventilation.
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code, ANSI 223.1, Section 5.3 or applicable local codes. NOTE: ANSI 223.1 is also known as NFPA 54.
5
AIR FOR COMBUSTION AND VENTILATION
Continued
VENTILATION AIR
VENTILATION AIR FROM INSIDE BUILDING
This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings; one within 12" of the ceiling and one within 12" of the floor on the wall connecting the two spaces (See Options 1 and 2, Figure 2). You can also remove door into adjoining room (See Option 3, Figure 2). Follow the National Fuel
Gas Code, NFPA 54/ANSI Z223.1, Section 5.3, Air for Combustion and Ventilation for required size of
ventilation grills or ducts.
WARNING: Rework work­sheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces.
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code,
NFPA 54/ANSI Z223.1, Section 5.3, Air for Combustion and Ventilation
for required size of ventilation grills or ducts.
IMPORTANT: Do not provide openings for inlet or outlet air into attic, if attic has a thermostat­controlled power vent. Heated air entering the attic will activate the power vent.
Ventilation Grills Into Adjoining Room, Option 1
Or Remove Door into Adjoining Room, Option 3
Ventilation Grills Into Adjoining Room, Option 2
12”
12"
FIGURE 2 - VENTILATION AIR FROM INSIDE BUILDING
OUTLET AIR
OUTLET AIR
INLET AIR
INLET AIR
VENTILATED ATTIC
VENTILATED CRAWL SPACE
FIGURE 3 - VENTILATION AIR FROM OUTDOORS
TO ATTIC
TO CRAWL SPACE
INSTALLATION
6
NOTICE: This heater is intended
for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. Do not run ceiling fan while heater is running. In the event of a power outage, you can use this heater as your primary heat source.
WARNING: A qualified service
person must install heater. Follow all local codes.
WARNING: Never install the
heater
in a bedroom or bathroom
in a recreational vehicle
where curtains, furniture,
clothing, or other flammable objects are less than 48 inches from the front, top, or sides of the heater
in high traffic areas
in windy or drafty areas
CAUTION: This heater creates
warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls.
IMPORTANT: Vent-free heaters
add moisture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 4 through 5.
Maintain adequate clearances for accessibility for the purpose of servicing and proper operation.
GAS CONNECTION
Check gas type. Use only the type of gas indicated on the valve rating plate. If the type of gas listed on the plate is not your type of gas supply,DO NOT INSTALL.
Contact your dealer for proper model. Always use an external regulator for all LP heaters to reduce the supply tank pressure to a maximum of 13" W.C. This is in addition to the regulator furnished with the heater.
Warning: Connection directly to an unregulated LP tank can cause an explosion.
The normal gas connection is 3/8" NPT made at the right side facing the log set. If a left side connection is desired, the connecting pipe may be routed under the rear of the burner base to terminate at the right hand side for connection to the inlet of the valve.
NOTE: The connecting pipe must be internally treated for protection from sulfur compounds if copper tubing is used for natural gas. Test for leaks using a solution of soap and water after completing the connection. DO NOT USE OPEN
FLAME.
CLEARANCES TO COMBUSTIBLES (Vent-Free Operation Only)
WARNING:
minimum clearances. If you can, provide greater clearances from floor, ceiling, and adjoining side and back walls.
Carefully follow the instructions below. This stove is a freestanding unit designed to set directly on the floor. Do not place stove directly on carpeting, vinyl tile, or any combustible material other than wood. The stove must set on a metal or wood panel extending the full width and depth of the appliance.
Maintain the
IMPORTANT: You must maintain
minimum wall and ceiling clearances during installation. The minimum clearances are shown in Figure 4. Measure from outermost point of stove top.
Minimum Wall and Ceiling Clearances (See Figure 4)
A. Clearances from outermost
point of stove top to any combustible side wall should not be less than 4 inches.
B. Clearances from outermost
point of stove top to any combustible back wall should not be less than 4 inches (Includes Corner Installations).
C. Clearances from the stove top
to the ceiling should not be less than 48 inches.
FRONT VIEW
4" MINIMUM
SIDE WALL
TOP VIEW
SIDE WALL
CORNER
4" MINIMUM
4" MINIMUM
WALL
4" MINIMUM
CEILING
48" MINIMUM
BACK WALL
4" MINIMUM
4" MINIMUM
SIDE WALL
SIDE WALL
WALL
FIGURE 4 - MINIMUM CLEARANCES TO WALLS AND CEILING
7
INSTALLATION
Continued
STOVE CAVITY ASSEMBLY
1. Lift off corrugated box enclosing stove body crating.
2. Remove all screws fastening the wood frame enclosure. Spread wood frame open and lift away from plastic-bagged stove body. The bottom pieces of pallet wood will remain bolted to the stove body.
3. Remove plastic bag from stove body.
4. Remove back panel from stove, if equipped (See Figure 5). Use an adjustable wrench or a 10 mm socket. Remove six (6) bolts and washers. Keep bolts and washers to reattach back panel later.
5. Remove all contents from inside stove cavity. Contents include:
(4) - Legs (includes leg leveler
bolts) (1) - Bottom door (3) - Top grates (1) - Hardware kit bag with
fasteners
6. Carefully lay stove body on back to attach bottom components to stove body (See Figure 6). Rest stove on drop cloth or blanket to avoid scratching stove edges.
7. Remove remaining pallet wood attached to bottom of stove body (See Figure 6). Use an adjustable wrench to remove bolts.
CAUTION: Cast Iron is brittle.
Do not over-tighten bolts or screws during assembly.
8.
Fasten each leg to stove with four (4) M8 x 1.25—20 mm bolts. Use a flat washer and lock washer with each bolt. Tighten bolts into threaded holes on stove body (See Figures 7 and 8). Use an adjustable wrench or a 12mm socket.
FIGURE 5 - REMOVING BACK PANEL
NOTE: CVF200’s series are
not equipped with a back panel.
FRONT OF STOVE UNIT
DROP CLOTH/ BLANKET
DOOR HINGE STEP BOLT HOLE
REMOVE PALLET BOLTED TO STOVE BOTTOM
FIGURE 6 - LAYING DOWN STOVE ON SIDE
FRONT
LEG HOLE
BOLT
BACK STOVE PANEL
TOP OF STOVE UNIT
DOOR CATCH BOLT WITH ADJUSTABLE HEX NUTS HOLE
LEG HOLE
BOTTOM OF STOVE UNIT
LEG HOLE
LEG HOLE
FIGURE 7 - LOCATING THREADED HOLES FOR STOVE BOTTOM,LEGS
8
INSTALLATION
Continued
9. Attach stove door by inserting step bolt through door hinge pivot hole and into threaded hole in stove body (See Figure 9 and 10 on page 8). Use an adjustable wrench or a 12mm socket to fasten step bolt. Tighten step bolt until snug. Make sure door moves freely.
10. Install door catch bolt (M8 x 1.25 – 55mm with two M8 hex nuts) into threaded hole on stove body (See Figure 10, page 8). Use an adjustable wrench or a 12mm socket. The catch bolt has two hex nuts attached to it. The top nut is a bolt stop and the bottom nut is for door leveling adjustment.
STOVE DOOR
11. Check general catch bolt alignment with door claw. Make final adjustment and door leveling after stove is in normal standing position.
12. Carefully lift stove back up on its four attached legs.
13. Set top grate into stove top.
14. If available, install gas log heater inside stove cavity before installing the back panel (See
Installing Gas Log Heater Into Stove, page 9).
15. Fasten back panel to stove with six (6) M6 x 1—20mm bolts and washers. Make sure product identification label is located on the outside in lower left hand corner.
STOVE DOOR
WASHERS BOLTS
BOTTOM OF STOVE UNIT
FIGURE 8 - ATTACHING STOVE LEGS
NOTE: IF YOUR CASTING HAS A
DROP BOTTOM– DO NOT INSTALL– DISCARD THE BOTTOM.
DOOR
DOOR CLAW
FIGURE 10 - CATCH BOLT AND DOOR CLAW ORIENTATION
THREADED HOLE
DOOR HINGE
STEP BOLT
BOLT SHOULDER
FIGURE 9 - ATTACHING STOVE DOOR
BOLT STOP
ADJUSTING NUT
CATCH BOLT
DOOR HINGE
STEP BOLT
STOVE BOTTOM
BOLT SHOULDER
+ 26 hidden pages