A.2 Recycling information ..................................................................................................... 15
nevion.com | 3
Page 4
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
Reclocker
EQ
Microcontroller
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
Remote
Control
Bypass
Passive
LoopThrough
(-PL version
only)
Bypass
Format
IN
1 Product overview
The Flashlink DA-3GHD-8-PL and DA-3GHD-8 is a multi bit-rate distribution amplifier
module providing high performance media distribution for various signal formats from
19.4Mbps up to 2970Mbps. The unit can be configured to do cable equalizing and
reclocking of SMPTE 424M, SMPTE 292 and SMPTE 259M signal formats.
Both modules provide 8 reclocked non-inverting outputs, and the DA-3GHD-8-PL also
provides a passive loop-through output. The passive loop-through output facilitates
distribution of the source signal to multiple cards without corruption due to powerdown
or removal of cards. The passive loop-through output must be terminated into 75 ohm,
either by connecting it to a subsequent DA-3GHD-8-PL, or by attaching a 75 ohm BNC
terminator.
Both modules will detect HD and SD rates and automatically switch to correct output
slew-rate. The reclocker supports the bit-rates 270Mbps, 1483.5Mbps, 1485Mbps,
2967Mbps and 2970Mbps. For other rates the reclocker can automatically switch to
bypass mode and the DA-3GHD-8-PL/DA-3GHD-8 will work as a non-reclocking
distribution amplifier with cable equalizer. The DA-3GHD-8-PL/DA-3GHD-8 also
supports reclocking of DVB-ASI at 270Mbps, enabling all possible rates including
empty transport streams with only K28.5 padding packets. All 8 outputs (and the
passive loop-through output) are non-inverting and suitable for DVB-ASI.
The DA-3GHD-8-PL/DA-3GHD-8 is designed for all distribution purposes in studio,
duplication and Broadcast applications.
Figure 1: DA-3GHD-8-PL / DA-3GHD-8
nevion.com | 4
Page 5
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
Number of outputs
8 reclocked
1 passive loop-through (-PL version)
Connectors
75 Ohm BNC
Output Return loss
- < -15dB, 5MHz -1.5GHz
- < -10dB, 1.5GHz - 3GHz
Output signal level
800mV +/- 10%
Output signal rise / fall time
20% - 80%
- SD limit: [0.4ns – 1.5ns]; <0.5ns rise/fall var.
- HD limit: < 270ps, <100ps rise/fall var.
- 3G HD limit: <135ps, <50ps rise/fall var.
Amplitude overshoot
<10%
Polarity
- All outputs are non-inverting
Output timing jitter
- SD: <0.2 UI
- HD: <1 UI
- 3G HD: <1UI
Output alignment jitter
- SD: <0.15 UI
- HD: <0.15 UI
- 3G HD: <0.2UI
Number of inputs
1
Connectors
75 Ohm BNC
Input Return loss
- < -15dB, 5MHz -1.5GHz
- < -10dB, 1.5GHz - 3GHz
Jitter tolerance
- SD limit:
- 10Hz-10kHz: >1 UI
- 10kHz-10MHz: >0.2 UI
- HD limit:
- 10Hz-100kHz: >1 UI
- 100kHz-150MHz: >0.2 UI
- 3G HD limit:
- 10Hz-100kHz: >2 UI
- 100kHz-300MHz: >0.3 UI
2 Specifications
2.1 Electrical Outputs
2.2 Electrical Inputs
nevion.com | 5
Page 6
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
Cable equalization, DA-3GHD-8.
Format
Min.
Typical
Comments
SD-SDI
300m
Belden 8281
BER< 10E-12
Total length of cable included
patching between modules
325m
HD-SDI
150m
Belden 1694A
BER< 10E-12
Total length of cable included
patching between modules
200m
3GHD-SDI
70m
100m
Cable equalization, DA-3GHD-8-PL, single unit.
Format
Min.
Typical
Comments
SD-SDI
200m1,2
Belden 8281
BER< 10E-12
Total length of cable included
patching between modules
225m
2,3
HD-SDI
50m
1,2
Belden 1694A
BER< 10E-12
Total length of cable included
patching between modules
75m
2,3
3GHD-SDI
30m
1,2
40m
2,3
Cable equalization, DA-3GHD-8-PL, two looped units.
Format
Min.
Typical
Comments
SD-SDI
200m
1,2
Belden 8281
BER< 10E-12
Total length of cable included
patching between modules
225m
2,3
HD-SDI
50m
1,2
Belden 1694A
BER< 10E-12
Total length of cable included
patching between modules
60m
2,3
3GHD-SDI
25m
1,2
25m
2,3
Cable equalization, DA-3GHD-8-PL, three looped units.
Format
Min.
Typical
Comments
SD-SDI
175m
1,2
Belden 8281
BER< 10E-12
Total length of cable included
patching between modules
200m
2,3
HD-SDI
30m
1,2
Belden 1694A
BER< 10E-12
Total length of cable included
patching between modules
50m
2,3
3GHD-SDI
15m
1,2
20m
2,3
1
2
3
Measured with the following parameters at the limits of the standards simultaneously;
Amplitude (+/- 10%), Ambient temperature (0ºC/45ºC), Generator jitter:
The DA-3GHD-8-PL/DA-3GHD-8 supports a number of different formats. The correct
configuration can either be set with a DIP switch or with GYDA Control System. The
layout of DA-3GHD-8-PL/DA-3GHD-8 is shown in the drawing below with the DIP
switch to the upper left position.
Figure 2: DA-3GHD-8-PL/DA-3GHD-8 module layout
DIP switch configuration must be set according to Table 1:
Table 1: DA-3GHD-8-PL/DA-3GHD-8 DIP switches
nevion.com | 8
All DIP switches are off when pointing towards the release handle.
Page 9
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
- - -
- - -
- - -
- - -
ABYP
RCL
EQ
OVR
ON
1
8
- - -
- - -
- - -
- - -
ABYP
RCL
EQ
OVR
ON
1
8
- - -
- - -
- - -
- - -
ABYP
RCL
EQ
OVR
ON
1
8
3.1 Configuration Examples
Typical configurations for DA-3GHD-8-PL/DA-3GHD-8:
Figure 3: Default all off; Gyda controls the card
Figure 4: DIP control; Equalizing and reclocking turned on
Figure 5: Same as above, but if the input signal is something else than the supported bit-
rates, the reclocker will automatically enter bypass mode
nevion.com | 9
Page 10
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
4 Connections
Both module versions have a dedicated connector backplane which is mounted at the
rear of the sub-rack. The backplane layout is shown in Figure 6.
Due to signal performance discrepancies in slot 1 (leftmost position), slot 1
may not be used with this product for 3G-SDI.
HD, SD and ASI meets is not affected and meets their respective
performance specifications.
Figure 6: Layout of the backplanes DA-3GHD-8-PL-C1 and DA-3GHD-8-C1.
The electrical input signal is connected to the IN BNC. On the -PL version the signal is
then passively looped to the LOOP-OUT BNC. The LOOP-OUT BNC must not be left
open, if it is not connected to another DA-3GHD-8-PL-C1 backplane, it must be
equipped with a good quality 75ohm termination. All OUT1 to OUT8 BNC’s provides
non-inverted signals and can be used for all formats, included DVB-ASI. Unused
outputs should be terminated with 75ohm.
Note: In an application with two or three distribution cards looped together, the source
SDI-signal will travel through several BCN connector interconnects. It is therefore very
important that those connectors are of good quality and specified for the bitrate used.
Only new and fresh interconnection equipment should be used. This is especially
important to 3G-SDI.
nevion.com | 10
Page 11
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
IN LOOP-OUT
OUT5
OUT6
OUT7
OUT8
OUT1
OUT2
OUT3
OUT4
Source cable
Termination
Total cable length = Source cable
IN LOOP-OUT
OUT5
OUT6
OUT7
OUT8
OUT1
OUT2
OUT3
OUT4
IN LOOP-OUT
OUT5
OUT6
OUT7
OUT8
OUT1
OUT2
OUT3
OUT4
Source cable
L1
Termination
Total cable length =
Source cable + L1
IN LOOP-OUT
OUT5
OUT6
OUT7
OUT8
OUT1
OUT2
OUT3
OUT4
IN LOOP-OUT
OUT5
OUT6
OUT7
OUT8
OUT1
OUT2
OUT3
OUT4
IN LOOP-OUT
OUT5
OUT6
OUT7
OUT8
OUT1
OUT2
OUT3
OUT4
Source cable
L1
L2
Termination
Total cable
length =
Source cable +
L1 + L2
See the following drawings for illustration of how the DA-3GHD-8-PL modules are
looped together:
Figure 7: Single module
Figure 8: Two modules looped
nevion.com | 11
Figure 9: Three modules looped
Page 12
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
Diode \
state
Red LED
Yellow LED
Green LED
No light
Status
Module is faulty
Module is OK
Module has power
Module has
no power
Signal
No input signal
EQ bypassed or
muted
Input signal
present
Rate
Rate not
detected
Recl. bypassed
Reclocker locked
Fourth LED
not used
Status
Signal
Rate
Not used
5 Operation
The status of the module can be easily monitored visually by LED’s at the front of the
module. The LED’s are visible through the front panel as shown in Figure 10.
Figure 10: Panel indicator overview for DA-3GHD-8-PL/DA-3GHD-8 (text not printed on
the front panel).
The functions of the different LED’s are described in Table 2.
Table 2: LED status description
nevion.com | 12
Page 13
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
1.
The equipment will meet the guaranteed performance specification under the
following environmental conditions:
-
Operating room temperature
range:
0°C to 50°C
-
Operating relative humidity range:
<90% (non-condensing)
2.
The equipment will operate without damage under the following environmental
conditions:
-
Temperature range:
-5°C to 55°C
-
Relative humidity range:
<95% (non-condensing)
General environmental requirements for Nevion equipment
nevion.com | 13
Page 14
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
Product Warranty
The warranty terms and conditions for the product(s) covered by this manual follow the
General Sales Conditions by Nevion, which are available on the company web site:
www.nevion.com
nevion.com | 14
Page 15
DA-3GHD-8-PL / DA-3GHD-8 Rev. D
組成名稱
Part Name
Toxic or hazardous substances and elements
鉛
Lead
(Pb)
汞
Mercury
(Hg)
镉
Cadmium
(Cd)
六价铬
Hexavalent
Chromium
(Cr(VI))
多溴联苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
DA-3GHD-8-PL
DA-3GHD-8
O O O O O
O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is
below the limit requirement in SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used
for this part is above the limit requirement in SJ/T11363-2006.
Appendix A Materials declaration and recycling
information
A.1 Materials declaration
For product sold into China after 1st March 2007, we comply with the “Administrative
Measure on the Control of Pollution by Electronic Information Products”. In the first
stage of this legislation, content of six hazardous materials has to be declared. The
table below shows the required information.
This is indicated by the product marking:
A.2 Recycling information
Nevion provides assistance to customers and recyclers through our web site
http://www.nevion.com/. Please contact Nevion’s Customer Support for assistance with
recycling if this site does not show the information you require.
Where it is not possible to return the product to Nevion or its agents for recycling, the
following general information may be of assistance:
Before attempting disassembly, ensure the product is completely disconnected
from power and signal connections.
All major parts are marked or labeled to show their material content.
Depending on the date of manufacture, this product may contain lead in solder.
Some circuit boards may contain battery-backed memory devices.
nevion.com | 15
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.