Netopia 3386-ENT User Manual
Checklist
AKING
M
Cayman
ROADBAND
B
®
Cable/DSL Router
1
ORK
W
™
3386-ENT
Quickstart Guide
Connect the power transformer to the power jack on the Router back panel.
2.
Plug the power transformer into an appropriate electrical outlet.
The Power light should come on solid green.
Connect the Router to the Ethernet jack on your cable modem or DSL modem.
3.
Be sure your DSL or cable modem is installed according to its instructions, and connected to its appropriate wall jack. Insert one end of the gray modem cable in the
mm
MMMMooooddddeeeemm
port on the Cayman Router back panel. Insert the other end of the modem
cable into the Ethernet jack on your DSL or cable modem. The Modem indicator light
should blink for up to two minutes and then come on solid green.
Connect the yellow Ethernet cable to your first PC.
4.
The Ethernet light for the port where you connected the cable should blink briefly and
come on solid green.
When all of your connections are made, the status LEDs on the front of your Cayman Router
will light, according to the following diagram:
Power - Green when power is on
Modem -
1
3386-ENT
Front Panel
4
3
Power
2
Modem
Ethernet
Solid green when connected
Flashes green for traffic on the WAN
Ethernet 1, 2, 3, 4 -
Solid green when connected
to each port on the LAN.
Flash green when there is
activity on each port.
CCCChhhheeeecccckkkk yyyyoooouuuurrrr ppppaaaacccckkkkaaaaggggeeee ccccoooonnnntttteeeennnnttttssss::::
3
2
1
Ethernet
Cayman Router
4
Power
Modem
CD & Quickstart
Guide
Power
Supply
Gray RJ-45
Modem
Cable
Yellow RJ-45
Ethernet
Cable
Set up your Router
After unpacking your Cayman Router shipping carton, decide where you want
1.
to locate the Router.
You should install the Router near your PC or another location that permits easy access
and visibility. You can lay the Cayman Router flat or mount it on a wall. Make sure any
Ethernet cables are kept away from power cords, fluorescent lighting fixtures, and
other sources of electrical interference. Put the Router in a location where air can circulate freely around it.
3386-ENT
Modem
Ethernet DC Power
Port
Back Panel
Modem
DSL or Cable
Modem
3
5.
Connect the Router to create your Ethernet local area network (LAN.)
Connect each computer or other device to a switch port on the back of the Router with
an Ethernet cable (maximum length 100 meters). If you need more than four ports, connect a hub or switch to the Router using a standard Ethernet cable.
Proceed to the next section “Configure Your PC for Dynamic Addressing” .
Ethernet 1234
4
Power
2
Configure Your PC for Dynamic Addressing
The following instructions assume that you want to use the automatic configuration and
address sharing features of the Router to provide IP information to devices on your local
Ethernet network.
Configure your computer to use an IP address on the same TCP/IP network as
1.
the Cayman Router.
• Windows 95/98 or Windows ME:
• Right-Click on the NNNNeeeettttwwwwoooorrrrkkkk NNNNeeeeiiiigggghhhhbbbboooorrrrhhhhoooooooodd
select PPPPrrrrooooppppeeeerrrrttttiiiieeeess
• In the list of network components, highlight the entry that says
“ TTTTCCCCPPPP////IIIIPPPP (((([[[[yyyyoooouuuurrrr EEEEtttthhhheeeerrrrnnnneeeetttt ccccaaaarrrrdddd hhhheeeerrrreeee]]]]))
• Click the PPPPrrrrooooppppeeeerrrrttttiiiieeeess
• Click the OOOObbbbttttaaaaiiiinnnn aaaannnn IIIIPPPP aaaaddddddddrrrreeeessssssss aaaauuuuttttoooommmmaaaattttiiiiccccaaaallllllllyy
figuration tab. Click the DDDDiiiissssaaaabbbblllleeee DDDDNNNNSS
any installed Gateways. Click the OOOOKK
• Proceed to the next section “Configure Your Cayman Router” .
• Windows 2000 and XP
• Right Click on the MMMMyyyy NNNNeeeettttwwwwoooorrrrkkkk PPPPllllaaaacccceeeess
PPPPrrrrooooppppeeeerrrrttttiiiieeeess
• Select your LLLLooooccccaaaallll AAAArrrreeeeaaaa CCCCoooonnnnnnnneeeeccccttttiiiioooonn
• Right click on your LLLLooooccccaaaallll AAAArrrreeeeaaaa CCCCoooonnnnnnnneeeeccccttttiiiioooonn
• Select IIIInnnntttteeeerrrrnnnneeeetttt PPPPrrrroooottttooooccccoooollll [[[[TTTTCCCCPPPP////IIIIPPPP]]
• Click the PPPPrrrrooooppppeeeerrrrttttiiiieeeess
• Click the OOOObbbbttttaaaaiiiinnnn IIIIPPPP aaaaddddddddrrrreeeessssssss aaaauuuuttttoooommmmaaaattttiiiiccccaaaallllllllyy
sssseeeerrrrvvvveeeerrrr aaaaddddddddrrrreeeessssssss aaaauuuuttttoooommmmaaaattttiiiiccccaaaallllllllyy
• Proceed to the next section “Configure Your Cayman Router” .
ss
from the pull-down menu.
ss
button.
ss
.
ss
button.
SS
KK
button twice. When prompted, restart your PC.
yy
radio button. Click the OOOOKK
dd
icon on your Windows desktop and
))
”.
yy
radio button. Click the DNS Con-
radio button. Click the Gateway tab and remove
ss
icon on your Windows desktop and select
nn
.
nn
and select PPPPrrrrooooppppeeeerrrrttttiiiieeeess
]]
.
yy
radio button and the OOOObbbbttttaaaaiiiinnnn DDDDNNNNSSSS
KK
button.
ss
.
2 3
IP Easy Setup
Ethernet IP Address: 192.168.1.1
Ethernet Subnet Mask: 255.255.255.0
Domain Name: isp.com
Primary Domain Name Server: 0.0.0.0
Secondary Domain Name Server: 0.0.0.0
Default IP Gateway: 0.0.0.0
IP Address Serving: On
Number of Client IP Addresses: 100
1st Client Address: 192.168.1.100
PREVIOUS SCREEN NEXT SCREEN
Enter an IP address in decimal and dot form (xxx.xxx.xxx.xxx).
Set up the basic IP & IPX attributes of your Netopia in this screen.
Easy Setup Security Configuration
It is strongly suggested that you password-protect configuration access
to your
Netopia. By entering a Name and Password pair here, access via serial,
Telnet and Web Server will be password-protected.
Be sure to remember what you have typed here, because you will be prompted
for
it each time you configure this Netopia.
Write Access Name:
Write Access Password:
PREVIOUS SCREEN TO MAIN MENU RESTART DEVICE
Configure a Configuration Access Name and Password here.
• Macintosh Mac OS
Your Macintosh must be using MacOS 7.6.1 or higher.
• Select CCCCoooonnnnttttrrrroooollll PPPPaaaannnneeeellllss
ss
from the Apple Menu.
• Open the TCP/IP Control Panel.
• Choose CCCCoooonnnnnnnneeeecccctttt vvvviiiiaaaa EEEEtttthhhheeeerrrrnnnneeeett
• Choose CCCCoooonnnnffffiiiigggguuuurrrreeee UUUUssssiiiinnnngggg DDDDHHHHCCCCPPPP SSSSeeeerrrrvvvveeeerr
tt
.
rr
. Close and Save.
You do not have to restart the Macintosh.
• Proceed to the next section “Configure Your Cayman Router” .
• Mac OS X
• Launch System Preferences from the Dock or from the Apple Menu.
• Select the NNNNeeeettttwwwwoooorrrrkk
• Choose SSSShhhhoooowwww:::: BBBBuuuuiiiilllltttt----iiiinnnn EEEEtttthhhheeeerrrrnnnneeeett
kk
Preference Pane.
tt
.
• Click the TCP/IP tab.
• Choose CCCCoooonnnnffffiiiigggguuuurrrreeee:::: UUUUssssiiiinnnngggg DDDDHHHHCCCCPP
PP
.
• Quit System Preferences.
You do not have to restart the Macintosh.
• Proceed to the next section “Configure Your Cayman Router” .
To connect additional computers that will use the Router’s address sharing
2.
feature repeat Step 1.
4
pp
NN
and
nn
.
pp
--
Configure Your Cayman Router
Run a Telnet application from the computer on the same network as the
1.
Router.
• Windows users click on the SSSSttttaaaarrrrtt
tt
menu, select RRRRuuuunn
type “ telnet 192.168.1.1 " (without the quotes).
• Macintosh OS X users launch the TTTTeeeerrrrmmmmiiiinnnnaaaall
the Utilities folder, and type “ telnet 192.168.1.1 " (without the quotes).
• Classic Macintosh OS users need to install the NCSA Telnet application, included on
the Netopia CD, or freely available from user groups or other freeware sources. Then
launch NCSA Telnet and type “ telnet 192.168.1.1 " (without the quotes).
The Telnet window displays the MMMMaaaaiiiinnnn MMMMeeeennnnuu
Cayman Router
Easy Setup...
WAN Configuration...
System Configuration...
Utilities & Diagnostics...
Statistics & Logs...
Quick Menus...
Quick View...
nn
, and in the resulting entry box,
ll
application, either from the Dock or from
uu
.
In the Telnet screens,
move from field to field
with the arrow keys.
Select items with the
nn
RRRReeeettttuuuurrrrnn
key, and toggle
items with the TTTTaaaabb
followed by RRRReeeettttuuuurrrrnn
Select EEEEaaaassssyyyy SSSSeeeettttuuuupp
press RRRReeeettttuuuurrrrnn
The IIIIPPPP EEEEaaaassssyyyy SSSSeeeettttuuuupp
screen appears.
Make any changes that
your ISP requires. Select
NNNNEEEEXXXXTTTT SSSSCCCCRRRREEEEEEEENN
press RRRReeeettttuuuurrrrnn
The EEEEaaaassssyyyy SSSSeeeettttuuuupp
SSSSeeeeccccuuuurrrriiiittttyyyy CCCCoooonnnnffffiiiigggguuuurrrraaaa--
nn
ttttiiiioooonn
screen appears.
Enter a name and password that will limit
access to the Router’s
bb
key
nn
.
pp
and
nn
.
configuration screens.
Select RRRREEEESSSSTTTTAAAARRRRTTTT
EE
DDDDEEEEVVVVIIIICCCCEE
and press
nn
RRRReeeettttuuuurrrrnn
.
Return/Enter goes to Easy Setup -- minimal configuration.
You always start from this main screen.
WAN Ethernet Configuration
Enable PPP over Ethernet: Off
Address Translation Enabled: Yes
Local WAN IP Address 0.0.0.0
TO MAIN MENU NEXT SCREEN
Set up the basic IP attributes of your Ethernet Module in this screen.
The WWWWAAAANNNN EEEEtttthhhheeeerrrrnnnneeeetttt
CCCCoooonnnnffffiiiigggguuuurrrraaaattttiiiioooonn
nn
screen
appears.
Make any changes that
your ISP requires. Select
NNNNEEEEXXXXTTTT SSSSCCCCRRRREEEEEEEENN
press RRRReeeettttuuuurrrrnn
NN
and
nn
.
2.
The Cayman Router will then restart and your settings will take effect.
CCCCoooonnnnggggrrrraaaattttuuuullllaaaattttiiiioooonnnnssss!!
!!
Your installation is complete. You can now surf to your favorite Web sites
by typing an URL in your browser’s location box or by selecting one of your favorite Internet
bookmarks.
If you have any questions or encounter problems with your Cayman Router, refer to the
detailed documentation on the Netopia CD, or contact your service provider’s technical support helpdesk.
Answers to many frequently asked product-related questions are also available on-line at:
http://www.netopia.com/support
NNNNeeeettttooooppppiiiiaaaa PPPPaaaarrrrtttt NNNNuuuummmmbbbbeeeerrrr::
::
6180057-00-01
Copyright 2003, Netopia, Inc. Netopia and Cayman are registered trademarks, and “Making
Broadband Work” is a trademark of Netopia, Inc. All rights reserved.
5
6
Loading...