Netgear SRC60 User Manual
Package Contents
Mount the Satellite on a Drop Ceiling
Mount the Satellite on a Wall
Orbi Pro Ceiling Satellite
(Model SRC60)
Metal bracket with T-bar
and lock screw for ceiling
mounting and 4 short
screws to attach the plastic
mount to the metal bracket
Before mounting the access point, rst set up and test the access
point to verify WiFi network connectivity.
Note: If you are mounting the access point on a hard ceiling,
follow the instructions in Mount the Satellite on a Wall.
1. Slide the T-bar partially
into the metal bracket.
2. Attach the metal bracket
to the ceiling bar.
3. Push the T-bar over the
ceiling bar.
4. Use the lock screw to
lock the metal bracket
into place.
5. Use the four short screws
to attach the plastic
mount to the metal
bracket.
1. Place the plastic mount
on the wall.
2. Mark the wall where the
two mounting holes are.
3. If needed, drill holes.
4. Use the two wall anchors
and tall screws to attach
the plastic mount to the
wall.
5. Slide the satellite onto
the plastic mount.
6. Use the retaining clip
to lock the satellite into
place.
Quick Start
Plastic mount for either
ceiling mounting or wall
mounting
2 tall screws and anchors
to attach the plastic mount
to a wall
Power adapter
(varies by region)
Note: If you use a Power over Ethernet (PoE) connection to a
PoE+ switch, the satellite does not require a power adapter.
Model SRC60
6. Slide the satellite onto
the plastic mount.
7. Cable the satellite to
your network.
7. Use the retaining clip
to lock the satellite into
place.
8. Cable the satellite to
your network.
PRO
Orbi Pro Ceiling Satellite Overview
Sync your Orbi Satellite With the
Manually Sync Your Satellite Before You Install It
Support
NETGEAR Insight App
You can use the NETGEAR Insight app to sync your Orbi satellite
with your Orbi Pro router. For more information about the app,
visit https://www.netgear.com/insight/.
1
2
Place your Orbi Pro router and Orbi satellite near each other during the syncing process. After your router and satellite are synced, mount
the satellite.
1. Place your Orbi satellite in an area near your Orbi Pro router.
2. Connect your satellite to a power source.
Either connect the power adapter to the satellite and to a power source or connect PoE+ LAN port 1 on the satellite to an Ethernet
cable and to a Power over Ethernet Plus (PoE+) switch that can provide 802.3at (PoE+) power.
The Power LED on the top panel of the Orbi satellite lights solid green.
Note: If the Power LED does not light, check the power source or the PoE+ switch. If the Power LED lights red, the power is not at the
required 802.3at (PoE+) level. Make sure that you use an 802.3at (PoE+) switch and not an 802.af (PoE) switch. For more information
about the Power LED, see the user manual, which you can download by visiting https://www.netgear.com/support/download/.
Thank you for purchasing this NETGEAR product. You can visit
https://www.netgear.com/support/ to register your product, get
help, access the latest downloads and user manuals, and join our
community. We recommend that you use only ofcial NETGEAR
support resources.
Si ce produit est vendu au Canada, vous pouvez accéder à ce
document en français canadien à
https://www.netgear.com/support/download/.
(If this product is sold in Canada, you can access this document
in Canadian French at
https://www.netgear.com/support/download/.)
3. Wait for the LED bar (next to the Power LED) to light solid white.
1. Download the NETGEAR Insight app from the Apple App
Store or Google Play Store.
The following is the LED bar behavior during booting:
• Pulsing white. The satellite is booting.
For regulatory compliance information including the EU
Declaration of Conformity, visit
https://www.netgear.com/about/regulatory/.
• Solid white. The satellite nished booting and is ready to sync with your router.
See the regulatory compliance document before connecting the
power supply.
2. Launch the NETGEAR Insight app on your mobile device and
follow the prompts.
Note: If you don’t own a mobile device, follow the instructions
in Manually Sync Your Satellite Before You Install It.
4. Press the Sync button on the back of your satellite, and within two minutes, press the Sync button on the back of your Orbi Pro router.
5. Wait for the satellite to sync with the router.
The LED bar on the satellite lights pulsing white while it attempts to sync with your Orbi Pro router. It might take about six minutes for
your satellite to sync.
After the LED bar lights pulsing white, it lights one of the following colors for about three minutes and then turns off:
1
Power LED on the top panel
2
LED bar on the top panel
3
DC power connector
4
PoE+ LAN 1 port
5
LAN 2 port
6
Reset button
Sync button
7
3 465
Blue
The Orbi Pro router and satellite successfully synced, and the connection between the router and satellite is good.
Amber
The Orbi Pro router and satellite successfully synced, and the connection between the router and satellite is fair. Consider moving
the satellite closer to the router.
Magenta
The Orbi Pro router and satellite did not sync. Move the satellite closer to the router and try again.
7
6. Mount your satellite and connect it to a power source.
You can mount your satellite on a ceiling or on a wall. For more information, see Mount the Satellite on a Drop Ceiling or Mount the
Satellite on a Wall on the other side of this quick start guide.
Either connect the power adapter to the satellite and to a power source or connect PoE+ LAN port 1 on the satellite to an Ethernet
cable and to a PoE+ switch that can provide 802.3at (PoE+) power.
7. Make sure that the LED bar lights blue to indicate a good connection to the Orbi router.
Note: After your satellite syncs with your router, the satellite’s Sync button is disabled for security reasons. If you press the Sync button
December 2018
and the satellite’s LED bar pulses magenta, this LED behavior indicates that the Sync button is disabled. To enable the Sync button, log
in to the router and go to the Attached Devices page. For more information, see the user manual.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of
NETGEAR, Inc. Any non-NETGEAR trademarks are used for reference purposes
only.
NETGEAR INTL LTD
Building 3, University Technology
Centre
Curraheen Road, Cork, Ireland
Loading...